Kanrich 915 User Manual - page 10
Call 915CC/Code setting button/Main monitor & Sub monitor setting button
Handsfree Talking / Monitoring Button
:
After talking press again for finish.
Handsfree Talking button
Press for getting a call and talking .
Monitoring button
:
Press to start monitor screen and monitor door camera situation and also to talk
with camera ,press
for finish. The talking time limitation is 180 sec.
again
Intercom Button/ N.O. Contact Point
Intercom
Press this button to intercom and talk with other monitors in this apartment .
When monitor screen is started , press this button and
N.O. Contact Point
drive this contact point in camera then to start other devices.
Door Release Button /
Code setting button
Door Release
Press “ "
door.
to open the
: When doorphone system is standby and press "
+
",
Code setting button
this button
code setting button
you will hear "Du" on 915M and on camera ,too. Please enter "monitor code"on camera immediately ,
7
915M will get this call and send "Ding-Dong" , it means a successful code setting .
7
In
/O
u
t
S
y
s
te
m L
in
e
+
F
G
N
D
S
y
s
te
m L
in
e
一
E
S
P
K
E
x
te
rn
a
l S
P
K
.
G
N
D
V
id
e
o O
u
t
B
e
ll
Monitor
E
x
te
rn
a
l d
o
o
r
b
e
ll s
w
it
c
h
For Intercom
function
DC
12V
+
D
C
1
2
V
REAR VIEW
Color Adj. Knob
Brightness Adj. Knob
Calling Tone Volume Knob
Side View
↑ +
↓ -
Power Indicator
Power Indicator - green - power on
Door Status Indicator(Red)
The red LED constantly lights on , it means the main door is
open, the red LED lights off ,it means the main door is close .
mic.
External power
for LCD screen
in apartment project.
915M7 7” Handsfree video monitor
spk.
Call 915CC :
Press “ " + " " to call control center and talk to the guard ; press “ “ again for finishing talk.
Code setting button
: When doorphone system is standby and press " + ",you will hear
"Du" on 915M7 and on camera ,too. Please enter "monitor code"on camera immediately , 915M7 will get this
call and send "Ding-Dong" , it means a successful code setting .
: Hold this button 8 sec. at least ,you will hear a high-pitch “Du",
Main monitor-Sub monitor setting button
it means to set main monitor successfully.Then, hold this button 8 sec. at least , you will hear a deep "Du",it
means to set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors in one apartment ,camera can't
call monitor normally ,the doorphone system will happen problem ,camera can't make a call to this apartment .
Specifications
Working Voltage: DC15V from 915P
Current Consumption : Stand-by 40mA,
Working 170mA(the power of LCD screen is
from external DC12V)
Working 450mA(the power of LCD screen is
from main line of doorphone)
Resolution: Color 7” 800RGB(H)x480(V)
Installation way: Surface mounting type
Material: Aluminum & ABS
heat-resistant
Plastic
Dimensions: (H)150mm/(W)235mm/(D)28mm
Weights : 700gs
Measurement: 0.35 cuft
Accessories
1. 7-pin connector 1
2. Monitor Bracket 1
3. Screw Bag 1
P20
2011 Sep.
Dummy Load
ON
OFF
LCD screen power setting
Please pay attention to
the direction of short pin.
The LCD screen power is
from the main line
( for single
house project)
The LCD screen power is
from external DC12V power
(for apartment project)
"in use" indicator / Intercom Indicator (Red)
This indicator is on - It means one of residents is using ,
please wait this resident finishing talking then to use .
Green/Red mutual flashing, it means intercom function is started.