Kanrich 915 User Manual - page 11
Dummy
Load
ON
OFF
In
/O
u
t S
y
s
te
m L
in
e
+
F
G
N
D S
y
s
te
m L
in
e
一
E
S
P
K E
x
te
rn
a
l S
P
K
.
G
N
D
V
id
e
o O
u
t
B
e
ll
E
x
te
rn
a
l d
o
o
r
b
e
ll s
w
it
c
h
DC
12V
+
D
C
1
2
V
rear view
External power
G
N
D
Monitor
SD
915M7b 7” Touch Pad Handsfree video monitor
Clock
when the screen on and time is display, access to toolbar and choose for adjusting time.
"in use" indicator / Intercom Indicator (Red)
The red light on - It means one of residents is using ,please wait
this resident finishing talking then to use .
The red light flashing, it means intercom function is started.
Door Status Indicator / picture indicator(Red)
The red light on constantly, it means the main door is
open, the red light off, it means the main door is close .
The red light flashing, it means the new picture coming.
Touchpad
In standby status,only the first key(top one) has indicator, just touch
it on touch area, all 5 touch keys with 5 indicators on and screen on
immediately. Please touch the touch key according to icon(on the
left view of touchpad).
Calling Tone
Volume Knob
Code setting
: When system is standby and touch " + ",you will hear "Du" on 915M7b and on camera ,too.
Please enter "monitor code"on camera immediately , 915M7b will get this call and send "Ding-Dong" , it means a successful
code setting .
: Keep touching 8 sec. at least ,you will hear a high-pitch “Du", it means to set main
Main monitor-Sub monitor setting
monitor successfully.Then, keep touching 8 sec. at least , you will hear a deep "Du",it means to set sub monitor successfully.
PS. One apartment only can set one main monitor, if you set 2 main monitors in one apartment ,camera can't call monitor(You
can hear “Ding-Dong” on monitor but no video).
The same problem will be happened when the system is no “main monitor” setting .
Code setting/Main monitor & Sub monitor setting
Monitor on or operate something then return to “Home Screen”, within 10 sec. without next operation, the screen
will be off and return to standby status. If you need further information, please access to , touch and get
more informaton(next pages) by touch and .
Adjust clock : The clock is on the upper left side , access to and touch for adjusting time .
Adjust brightness : Access to and touch for adjusting brightness .
Check pictures or change picture quantity : Access to , touch for choosing 0/1/3 .
PS.1. The period of taking picture, all buttons are locked temporarily till finish taking picture.
2. Automatically take picture set "3" - "go out" mode - one call , take 3 pictures ;
set "1" - "at home" mode - one call, take 1 picture ;
set "0" - "no picture" mode , no tate picture.
3. Due to the period of taking picture, all buttons are locked temporarily. When camera call monitor and start to
take a picture, you have to wait till finish "take a picture" then talk with monitor . The waiting time is about
12 sec. from calling to finish taking a picture.
Talking Volume Knob
Specifications
Working Voltage: DC15V from 915P
Current Consumption : Stand-by 200mA
Working 600mA
Resolution: Color 7” 800RGB(H)x480(V)
Installation way: Surface mounting type
Material: ABS
heat-resistant plastic
Dimensions: (H)155mm/(W)256mm/(D)27mm
Weights : 500gs
Measurement: 0.35 cuft
For Intercom
function
Accessories
1. 6-pin connector 1
2. 2-pin connector 1
3. Monitor Bracket 1
4. Screw Bag
1
SPK.
MIC.
2012/ 12/ 12 12: 12: 12
P21