Kanrich 915 User Manual - page 14
Door Release -1 / Resident Code Setting
1. Door Release - 1
When a calling is from camera, press
this button and pick up the handset to open the 1st door.
2.Resident Code Setting
915M3
,
When doorphone system is standby and press " + ", you will hear "Du" on
and on camera too.
Please enter "
code" on camera immediatel
will get this call and send "Ding-Dong" , it means
resident
y, 915M3
a successful code setting .
JP1
T3
UP
6 5 4 3 2 1
Inside View
of Base
PCB
Dummy Load Switch
Set “ON”
6 5 4 3 2 1
DUMMY
←ON OFF→
In
/O
u
t M
a
in L
in
e
+
F
G
N
D M
a
in L
in
e
一
G
N
D
G
ro
u
n
d W
ir
e
B
e
ll
E
x
te
rn
a
l D
o
o
r B
e
ll S
w
it
c
h
(I
n
te
rc
o
m
)
Button Switch
N
o F
u
n
c
tio
n
915M3 Audio Handset
Resident Code Setting / Main Handset & Sub-Handset Setting
1.
Resident Code Setting
915M3
,
When doorphone system is standby and press " + ", you will hear "Du" on
and on camera too.
Please enter "
code" on camera immediatel
will get this call and send "Ding-Dong" , it means
resident
y, 915M3
a successful code setting .
2. Main Handset or Sub-Handset Setting
Press this button 8 sec. at least and you will hear a high-pitched “Du”, this handset is set as main handset .
Press this button 8 sec. at least and you will hear a low-pitched “Du”, this handset is set as sub-handset .
To identify the “Du” is high-pitched or “low-pitched” as main or sub handset.
If there are 2 monitors(915M) or “monitor(915M) + audio handset” in one house, it is necessary to set main monitor
and sub-monitor(handset) because one house only allow one main monitor, other monitors(handsets)
are sub-monitors(handsets).
Intercom / Door Release - 2
1. Intercom
Pick up the handset and press this button and talk with another monitor(or handset),
the talking time is 3 min. Hang up the handset and finish talking.
2. Door Release - 2
When a calling is from camera, pick up the handset and press this button to open the 2nd door .
Handset
ick up the handset and talk with camera or other monitors hen you hear the ringing tone, the tal
P
king time limitation is 180 sec.
w
When you are talking with camera, an intercom call coming, please hang up the handset first then pick up the handset again
for getting this intercom call.
Rear View of Front Cover
Power Indicator
On
-
Green
In Use / Intercom Indicator
On
-
Red
:
System in using
,
after Led off then to use
.
Flashing
-
Red
:
Intercom in using
,
after Led off then to use
.
Door Status Indicator
On
-
Red
Door is Open
N
o F
u
n
c
tio
n
Connect to other monitors(Handsets) in the same house.
Specifications
Working Voltage:
DC15V from 915P
Current Consumption :
Stand-by 40mA, Working 150mA
Communicating Interface:
the modulated carrier wave signal
Installation way: Surface mounting type
Material: ABS
heat-resistant plastic
Dimensions: (H)206mm/(W)92mm/(D)58mm
Weights : 400gs
Measurement: 0.5 cuft
P24
2011 Sep.