Lanier R/C MARINER 40 MK II ARF Instruction Manual - page 3
3
7. If you are not an experienced pilot or have not flown
this type of model before, we recommend that you get
the assistance of an experienced pilot in your R/C club for
your first flights. If you’re not a member of a club, your local
hobby shop has information about clubs in your area whose
membership includes experienced pilots.
8. While this kit has been flight tested to exceed normal use,
if the plane will be used for extremely high stress flying, such
as racing, or if an engine larger than one in the recommended
range is used, the modeler is responsible for taking steps to
reinforce the high stress points and/or substituting hardware
more suitable for the increased stress.
9. WARNING: The cowl and wheel pants included in this kit
are made of fiberglass, the fibers of which may cause eye,
skin and respiratory tract irritation. Never blow into a part
to remove fiberglass dust, as the dust will blow back into
your eyes. Always wear safety goggles, a particle mask and
rubber gloves when grinding, drilling and sanding fiberglass
parts. Vacuum the parts and the work area thoroughly after
working with fiberglass parts.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and fl yability of your fi nished model depends
on how you build it; therefore, we cannot in any way
guarantee the performance of your completed model,
and no representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow the instructions
to end up with a well-built model that is straight and true.
DECISIONS YOU MUST MAKE
This is a partial list of items required to finish the Stinger II
.46 ARF that may require planning or decision making before
starting to build. Order numbers are provided in parentheses.
Radio Equipment
The Stinger requires a minimum 4-channel radio system with
five 44 oz.-in. [3.2 kg-cm] minimum standard sized servos.
In addition, two 6" [152mm] servo extensions are required
for the aileron servos. If you are using a radio system that
does not support mixing functions, a Y-harness will also be
required to connect the aileron servos to the receiver.
Recommended part numbers for the radio components are
provided below:
❏
(5) Futaba
®
S3004 Standard Ball Bearing Servo (FUTM0004)
❏
(2) Hobbico
®
6" Extension Futaba J (HCAM2000)
❏
Futaba Dual Servo Extension 6" J (FUTM4130)
❏
Ernst Charge Receptacle Futaba J FM (ERNM3001)
Engine Recommendations
The recommended engine/motor size for the Stinger is a
.46-.55 cu in [7.5-9cc] two-stroke engine or a .70-.72 cu in
[11.5-12cc] four-stroke engine. A pitts muffler is also required.
Choose a propeller based on the engine manufacturer’s
recommendation. Order numbers are provided below:
❏
O.S.
®
.46AX ABL w/Muffler (OSMG0547)
❏
Bisson Pitts Muffler O.S. 55AX (BISG4046)
❏
O.S.
®
FS72-A Ring (OSMG0877)
ADDITIONAL ITEMS REQUIRED
Hardware and Accessories
This is the list of hardware and accessories required to finish
the Stinger. Order numbers are provided in parentheses:
❏
R/C foam rubber 1/4" [6mm] (HCAQ1000)
❏
3' [900mm] standard silicone fuel tubing (GPMQ4131)
Adhesives and Building Supplies
This is the list of Adhesives and Building Supplies that are
required to finish the Stinger II .46 ARF:
❏
1/2 oz. [15g] Thin Pro
™
CA (GPMR6001)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Threadlocker thread locking cement (GPMR6060)
❏
Denatured alcohol (for epoxy clean up)
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32" [2.4mm]
❏
Great Planes Tap & Drill Set 6-32 (GPMR8102)
❏
Tap handle (GPMR8120)
❏
Rotary tool with cutting bit
❏
Revell
®
Premium Soft Handle Knife w/Blades (5)
(RMXR6900)
❏
Top Flite
®
MonoKote
®
sealing iron (TOPR2100)
❏
Top Flite Hot Sock
™
iron cover (TOPR2175)
❏
Panel Line Pen (TOPQ2510)
❏
Hobbico Steel T-Pins 1" (100) (HCAR5100)
❏
Harry Higley’s 3/16" Extended Drill (HIGR1020)
❏
Small clamps
❏
Masking tape
❏
Household oil
Optional Supplies and Tools
Here is a list of optional tools that will help you build the
Stinger II .46 ARF:
❏
1/2 oz. [15g] Thick Pro CA- (GPMR6013)
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
4 oz. [113g] aerosol CA activator (GPMR6034)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Great Planes Pro Epoxy 6-Minute Formula 4 oz
(GPMR6042)