M Design LUNA 1000H Instructions For Installation And Use Manual - page 8
2.5 Convectiestroming
2.5.1 Natuurlijke convectie
Het is verplicht 2 of 4 warmeluchtuitgangen te openen aan de bovenkant van het
toestel. 2 is voldoende als u met een ventilator werkt ( optie ) en 4 openingen indien
geen ventilator voorzien wordt . Indien het metselwerk niet toelaat de bovenste con-
vectiegaten te gebruiken, kan men de twee bovenste, zijdelingse openingen gebrui-
ken. In dit geval moet een ventilator geplaatst worden.
Om natuurlijke convectie toe te laten langs de onderzijde wordt de haard op min.
20 mm van de grond geplaatst (bij plaatsing op de grond). Voor de ingang van de
lucht (ventilatie), moet een doorgang van min. 4 dm² zonder filter in het metselwerk
voorzien zijn, of van min. 6 dm² mét een stoffilter.
(Let op: rekening houden met de coëfficiënt van de doorgang van de roosters).
De ingangen van de verse lucht bevinden zich aan de achterzijde, linker en rech-
terzijde van het toestel en onder het toestel, zijnde de opening voorzien voor de
ventilator .
2.5.2 Convectie door ventilator (optie)
Het is verplicht om min. 2 warmeluchtuitgangen te openen. Het is noodzakelijk de
luchttoevoer en -uitgangen in het metselwerk correct te scheiden. Sommige isola-
tiematerialen worden met de tijd aangetast, het is noodzakelijk ze van de ventilatie-
luchttoevoer te scheiden, anders loopt men het risico dat ze opgezogen worden en
door het huis gediffuseerd worden. Het is dus ook meest aan te raden vaste isolatie-
platen te gebruiken. (Promatec..). De ventilator kan zowel vanbuiten als langs binnen
gemonteerd worden, wat ons de mogelijkheid geeft van zelfs later een ventilator te
plaatsen.
2.5.3 Warmeluchtkanalen
Thermisch geïsoleerde kanalen zijn noodzakelijk voor de optimale werking van het
toestel (deze veroorzaken een ‘trek’ voor de convectielucht). Het maximum aantal
kanalen gebruiken (min.2), verbetert het rendement en het geluid (dat door de ver-
plaatsing voortgebracht wordt). Voor de installatie van deze kanalen, best om eerst
min 1 m. verticaal naar boven te gaan om daarna een richtingsverandering door te
voeren, buig vrij breed om en beperk de richtingsveranderingen. Vermijd het gebruik
van uitgangsroosters met een kleine doorlaat, want de veroorzaakte snelheidsverlie-
zen verminderen de doeltreffendheid van de warmeluchtuitlaten.
M-design heeft hiervoor ideale warme luchtroosters ontwikkeld met vele voordelen.
2.5 Convection current
2.5.1 Natural convection
It is compulsory to open 2 or 4 hot air vents (see table 1) at the
top of the appliance. The entrance for the air supply convection are situated at the lower
backside of the Luna Diamond and also through the opening that is provided for the fan. These
have been constructed in such a way that no air can be blown out along here, not even with
a fan. The stove is placed at least 20 mm above the floor (if placed on the floor) to allow for
natural convection.
A clearance of at least 4 dm3 , excluding the measurements of a dust filter, or at least 6 dm3
, including the measurements of a filter, must be provided for in the masonry. (Note: Remember
to take the measurements of the clearance of the
grids into account.) (Pic.7a)
2.5.2 Convection by means of a fan (optional)
It is compulsory to open at least 2 hot air vents (see table 1). It is essential to separate the
air supply ducts and the air vents correctly in the masonry. Some insulation material gets da-
maged in time, and it is essential to separate it from the ventilation air supply, otherwise one
runs the risk that it is sucked in and spread in the house. It is therefore also advisable to use
fixed insulation plates (Promatec, HT-platen or promatec). The fan may be mounted either on
the outside or on the inside, which even makes it possible to install a fan afterwards.
2.5.3 Hot air ducts
Thermally insulated ducts are essential for the optimal functioning of the appliance (these cause
‘draught’ in the convection air current). By using the maximum number of ducts (at least 2), the
output is improved and the noise (that is caused by the displacement) is reduced.
For the purposes of the installation of these ducts it is best to go vertically upwards first for
at least 1m and then to change direction, making a rather wide bend and avoid using a flue
terminal grid with a small clearance because the speed loss that this causes reduces the ef-
ficiency of the hot air vents.
M-design has developed its ideal hot air grids which have many advantages (Pic 7b and 7c)
Installatievoorschrift en gebruiksaanwijzing - LUNA DIAMOND / Instructions for installation and use
- 6 -