Installation manual remote control auto starter with keyless entry and panic this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference; and [2] this device must accept any interference received, includ...
2 installer warnings installation this remote starter with keyless entry system is designed to be installed on fuel injected vehicles with an automatic transmission only. • never install this remote starter on a manual transmission vehicle. • some automatic transmission vehicles [mainly older gm veh...
Yellow wire with white stripe: [ignition 2 output] • provides [+] 12 volts while cranking and while running on remote control. • some vehicles have [2] ignition wires that must be powered. • connect to the vehicle's 2nd ignition wire that goes hot in the start and remains hot in the run position. If...
Cavity #8 vacant: [rear hatch/trunk pop output] this vacant cavity outputs a [-] signal to pop the rear hatch when the remote transmitter “unlock” button is depressed for 3 seconds or more. • the #8 cavity sends out a [-] signal to activate a relay coil. [300ma maximum] for vehicles that use a [-] p...
(-) lock out ground input (-) unlock out to door lock control relays lock control switch black wire: connect to unlock red wire: connect to lock orange wire: no connection 3 pin black plug 5 optional accessory connections (+) lock out +12 volts input (+) unlock out to door lock control relays black ...
Blue wire violet wire to b+ or ground as required white wire no connection brown wire no connection lock fuse 1 unlock fuse 2 black 3-pin plug green wire ala-dl1 to vehicles lock/unlock wire 6 optional accessory connections 87 87a 85 86 30 87 87a 85 86 30 to +12 volts (battery +) to ground to newly ...
Optional accessory connections (continued) 7 red wire lock all doors black wire unlock drivers door 87 87a 85 86 30 orange wire unlock wire passenger's door lock unlock to +12v or ground to +12v or ground driver's door rear door passenger door switch door lock relay control module lock unlock +12v m...
Optional accessory connections (continued) 87 86 85 30 white wire with black stripe (spst ala984h relay not supplied) output to power trunk switch to constant +12 volts input to relay (+ or -) insert white wire with black stripe into the eighth socket power trunk activation using optional 30 amp rel...
Optional accessory connections (continued) 9 transponder interfacing • you will need a transponder key that’s already programmed to the vehicle. • you will also need a transponder interface module. Our rs-tim module plugs directly into the remote starter module. • detailed instructions are included ...
Optional accessory connections (continued) 10 pass-lock interface the pass-lock system is similar to the pass-key system except the resistor is inside the steering column instead of the ignition key. 1. Locate pass-lock wires coming down the steering column. (3 bonded wires) 2. Determine wire color ...
11 transmitter code learning to enter code learning mode: [the module learns up to 4 transmitter codes] 1. Turn on the ignition key. 2. Depress the program switch [3] times within 30 seconds. After turning ignition key. 3. The horn will emit [1] long chirp to indicate you are now in code learning mo...
12 automatic door locking and unlocking feature programming warning- • if you program the automatic door locking feature “on” you “must” also connect one of our door trigger wires to the dome light wire of the vehicle. • do not risk the customer getting locked out of the vehicle. For proper operatio...
To enter remote starter feature programming: 1. Turn on the ignition key. 2. Depress the program switch [10] times within 30 seconds. After turning on ignition. 3. The parking lights will flash [10] times. The horn will chirp [10] times. 4. You are now in remote starter feature programming mode. Rem...
Remote starter checkout procedures 1. Apply the under-hood caution label on the radiator-housing shroud. 2. Remove all tools and close the hood. 3. Verify the transmission is in park position and apply the parking brake. 4. Remove the ignition keys and connect the 6-pin connector to the control modu...
1. Remote starter module will not activate: • the hood switch may be pointed in the wrong direction. Disconnect and re-try. • probe the pink brake wire to verify the wire is not until the brake is depressed. • probe the heavy red wires [both sides of the fuses] to verify +12 volts on each. • probe a...
Pl70im © 2000 copyright magnadyne corp. 3-10-00 rev. B 2p blue 3p white 2p green 2p orange 3p black + parking lights [-] parking lights red wire 12v+ input red wire 12v+ input black wire ground input yellow wire 1 ignition output yellow/white wire 2 ignition output vacant 12v+for relay coil (ala-rpt...
