Majorcom: EN 54-16 User manual - page 15
EN 54-16 certified PA/VA System SERIES
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
User manual V1.1
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
Usermanual V1.1
29
28
SERIES EN 54-16 certified PA/VA System
Page
28
sur
51
ϯ͘ϱ͘Ϯ
ROUTE SOURCES
To route any available audio source to any of the zones or group of zones press the button “ROUTE
SOURCES”. The following window will appear:
ĂͿ
EMERGENCY MICROPHONE
On special occasions, you can use the emergency microphone to make announcements by one or more
zones in PA mode. Once the audio source routing is concluded, use the PTT button on the microphone
to make the announcement.
ďͿ
PRE-RECORDED MESSAGES
From this menu, you can select one of the two pre-recorded message player sources integrated in the
equipment. To play the message, once the routing a message player is done, you must access the pre-
recorded message window in the advanced menu (see 3.5.7) and play the selected message.
ĐͿ
SELECTION INDICATOR
When the audio source has been selected, a blue band selection within the source button will appear.
ĚͿ
DEROUTE AUDIO SOURCE
To clear the current assignment of an audio source to a zone / zones, select the source marked as an "X".
A new routing is done automatically if you assign a new source to a zone that previously had an audio
source routed.
Once you have done the source selection, if you want to cancel, press the " BACK" button. To confirm the
selection, press the " OK" button, you will access to the zone selection menu where you can assign the
zones to be assigned sound source (see 2.2.7).
NOTE: When the ACSI bus is being used (see 4.2), the audio source number 5 will change into a
microphone icon. This source will also be shown as unavailable.
NOTE: When the zone selection is for one of the pre-recorded message players
or the EMIC, the
selection will be cleared when performing a new selection. When the selection if for any of the other
audio sources, the selection will be cumulative, meaning the zones not affected by the selection will keep
its audio routing.
ϯ͘ϱ͘ϯ
ADVANCED OPTIONS
The equipment/system has advanced adjustment options. To access these options, from the PA menu,
click on the "ADVANCED" button, a user control access level 3 (see 2.3) will be displayed. To return, press
the "BACK" button. Overcome the access control, the level of access authorization, will change to "Level
3" and access the menu, which contains the options:
Picture 32: Route sources Window
Page
28
sur
51
ϯ͘ϱ͘Ϯ
ROUTE SOURCES
To route any available audio source to any of the zones or group of zones press the button “ROUTE
SOURCES”. The following window will appear:
ĂͿ
EMERGENCY MICROPHONE
On special occasions, you can use the emergency microphone to make announcements by one or more
zones in PA mode. Once the audio source routing is concluded, use the PTT button on the microphone
to make the announcement.
ďͿ
PRE-RECORDED MESSAGES
From this menu, you can select one of the two pre-recorded message player sources integrated in the
equipment. To play the message, once the routing a message player is done, you must access the pre-
recorded message window in the advanced menu (see 3.5.7) and play the selected message.
ĐͿ
SELECTION INDICATOR
When the audio source has been selected, a blue band selection within the source button will appear.
ĚͿ
DEROUTE AUDIO SOURCE
To clear the current assignment of an audio source to a zone / zones, select the source marked as an "X".
A new routing is done automatically if you assign a new source to a zone that previously had an audio
source routed.
Once you have done the source selection, if you want to cancel, press the " BACK" button. To confirm the
selection, press the " OK" button, you will access to the zone selection menu where you can assign the
zones to be assigned sound source (see 2.2.7).
NOTE: When the ACSI bus is being used (see 4.2), the audio source number 5 will change into a
microphone icon. This source will also be shown as unavailable.
NOTE: When the zone selection is for one of the pre-recorded message players
or the EMIC, the
selection will be cleared when performing a new selection. When the selection if for any of the other
audio sources, the selection will be cumulative, meaning the zones not affected by the selection will keep
its audio routing.
ϯ͘ϱ͘ϯ
ADVANCED OPTIONS
The equipment/system has advanced adjustment options. To access these options, from the PA menu,
click on the "ADVANCED" button, a user control access level 3 (see 2.3) will be displayed. To return, press
the "BACK" button. Overcome the access control, the level of access authorization, will change to "Level
3" and access the menu, which contains the options:
Picture 32: Route sources Window
Page
28
sur
51
ϯ͘ϱ͘Ϯ
ROUTE SOURCES
To route any available audio source to any of the zones or group of zones press the button “ROUTE
SOURCES”. The following window will appear:
ĂͿ
EMERGENCY MICROPHONE
On special occasions, you can use the emergency microphone to make announcements by one or more
zones in PA mode. Once the audio source routing is concluded, use the PTT button on the microphone
to make the announcement.
ďͿ
PRE-RECORDED MESSAGES
From this menu, you can select one of the two pre-recorded message player sources integrated in the
equipment. To play the message, once the routing a message player is done, you must access the pre-
recorded message window in the advanced menu (see 3.5.7) and play the selected message.
ĐͿ
SELECTION INDICATOR
When the audio source has been selected, a blue band selection within the source button will appear.
ĚͿ
DEROUTE AUDIO SOURCE
To clear the current assignment of an audio source to a zone / zones, select the source marked as an "X".
A new routing is done automatically if you assign a new source to a zone that previously had an audio
source routed.
Once you have done the source selection, if you want to cancel, press the " BACK" button. To confirm the
selection, press the " OK" button, you will access to the zone selection menu where you can assign the
zones to be assigned sound source (see 2.2.7).
NOTE: When the ACSI bus is being used (see 4.2), the audio source number 5 will change into a
microphone icon. This source will also be shown as unavailable.
NOTE: When the zone selection is for one of the pre-recorded message players
or the EMIC, the
selection will be cleared when performing a new selection. When the selection if for any of the other
audio sources, the selection will be cumulative, meaning the zones not affected by the selection will keep
its audio routing.
ϯ͘ϱ͘ϯ
ADVANCED OPTIONS
The equipment/system has advanced adjustment options. To access these options, from the PA menu,
click on the "ADVANCED" button, a user control access level 3 (see 2.3) will be displayed. To return, press
the "BACK" button. Overcome the access control, the level of access authorization, will change to "Level
3" and access the menu, which contains the options:
Picture 32: Route sources Window
Page
29
sur
51
ĂͿ
AUDIO INPUT
Access window settings for the audio inputs. For more detail see 3.5.4
ďͿ
AUDIO OUTPUT
Access setting window for audio outputs. For more detail see 3.5.5
ĐͿ
MONITOR
The equipment/system has an integrated speaker that lets you hear the audio sources that are available,
and the audio input routed to each zone. For more detail see 3.5.6
ĚͿ
MESSAGES
Access to the pre-recorded messages menu.
ĞͿ
LOAD PRESET
Access to the selection window of saved memory with a certain system operation (preset). To configure
and save the preset you must use the configuration software.
ĨͿ
SYSTEM
Access to the system's information window and identification configuration.
ϯ͘ϱ͘ϰ
ADVANCED OPTIONS. AUDIO INPUT.
ĂͿ
AUDIO INPUT SELECTION BUTTONS
The audio inputs are in the left half of the screen. Click on the desired entry and if the progress indicator
appears (see 9), use the scroll control to display the rest of available audio inputs.
Picture 33: Advanced Options Menu
Picture 34: Audio Input Setting Window
Page
29
sur
51
ĂͿ
AUDIO INPUT
Access window settings for the audio inputs. For more detail see 3.5.4
ďͿ
AUDIO OUTPUT
Access setting window for audio outputs. For more detail see 3.5.5
ĐͿ
MONITOR
The equipment/system has an integrated speaker that lets you hear the audio sources that are available,
and the audio input routed to each zone. For more detail see 3.5.6
ĚͿ
MESSAGES
Access to the pre-recorded messages menu.
ĞͿ
LOAD PRESET
Access to the selection window of saved memory with a certain system operation (preset). To configure
and save the preset you must use the configuration software.
ĨͿ
SYSTEM
Access to the system's information window and identification configuration.
ϯ͘ϱ͘ϰ
ADVANCED OPTIONS. AUDIO INPUT.
ĂͿ
AUDIO INPUT SELECTION BUTTONS
The audio inputs are in the left half of the screen. Click on the desired entry and if the progress indicator
appears (see 9), use the scroll control to display the rest of available audio inputs.
Picture 33: Advanced Options Menu
Picture 34: Audio Input Setting Window
Page
29
sur
51
ĂͿ
AUDIO INPUT
Access window settings for the audio inputs. For more detail see 3.5.4
ďͿ
AUDIO OUTPUT
Access setting window for audio outputs. For more detail see 3.5.5
ĐͿ
MONITOR
The equipment/system has an integrated speaker that lets you hear the audio sources that are available,
and the audio input routed to each zone. For more detail see 3.5.6
ĚͿ
MESSAGES
Access to the pre-recorded messages menu.
ĞͿ
LOAD PRESET
Access to the selection window of saved memory with a certain system operation (preset). To configure
and save the preset you must use the configuration software.
ĨͿ
SYSTEM
Access to the system's information window and identification configuration.
ϯ͘ϱ͘ϰ
ADVANCED OPTIONS. AUDIO INPUT.
ĂͿ
AUDIO INPUT SELECTION BUTTONS
The audio inputs are in the left half of the screen. Click on the desired entry and if the progress indicator
appears (see 9), use the scroll control to display the rest of available audio inputs.
Picture 33: Advanced Options Menu
Picture 34: Audio Input Setting Window