Majorcom: EN 54-16 User manual - page 18
EN 54-16 certified PA/VA System SERIES
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
User manual V1.1
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
Usermanual V1.1
35
34
SERIES EN 54-16 certified PA/VA System
Page
34
sur
51
ĂͿ
FACTORY PRESET BUTTON
The factory preset button will load the default audio configuration of the equipment. All the audio
configuration that was configured by the user will be replaced.
ďͿ
BUTTON OF PRESET
Press over the preset button that you want to load. If the progress indicator is present (see 2.2.6) use the
scroll control to display the remaining presets available. To confirm press the button “OK”.
NOTE: It is possible to create or modify presets from the configuration software.
ϯ͘ϱ͘ϵ
ADVANCED OPTIONS. SYSTEM
ĂͿ
SYSTEM'S EQUIPMENT LIST BUTTONS
The left side of the windows will show the current equipment present in the system. If the progress
indicator is present (see 2.2.6) use the scroll control to display the remaining equipment units available.
Select the desired button in the list of items to show its information. A selection band will appear in the
selected item.
ďͿ
SYSTEM IDENTIFIER
In this section, you will find information of the equipment related to the system. First, there is the name
or identifier of the equipment, followed by the serial number associated with it. Below, you will see the
version of the equipment's operating system, followed by the version of the application firmware
installed. To upgrade the firmware, you must use the configuration software.
Picture 38: Load Preset Window
Picture 39: System's Advanced Options Window
Page
34
sur
51
ĂͿ
FACTORY PRESET BUTTON
The factory preset button will load the default audio configuration of the equipment. All the audio
configuration that was configured by the user will be replaced.
ďͿ
BUTTON OF PRESET
Press over the preset button that you want to load. If the progress indicator is present (see 2.2.6) use the
scroll control to display the remaining presets available. To confirm press the button “OK”.
NOTE: It is possible to create or modify presets from the configuration software.
ϯ͘ϱ͘ϵ
ADVANCED OPTIONS. SYSTEM
ĂͿ
SYSTEM'S EQUIPMENT LIST BUTTONS
The left side of the windows will show the current equipment present in the system. If the progress
indicator is present (see 2.2.6) use the scroll control to display the remaining equipment units available.
Select the desired button in the list of items to show its information. A selection band will appear in the
selected item.
ďͿ
SYSTEM IDENTIFIER
In this section, you will find information of the equipment related to the system. First, there is the name
or identifier of the equipment, followed by the serial number associated with it. Below, you will see the
version of the equipment's operating system, followed by the version of the application firmware
installed. To upgrade the firmware, you must use the configuration software.
Picture 38: Load Preset Window
Picture 39: System's Advanced Options Window
Page
35
sur
51
ĐͿ
LOCATION IDENTIFIER
This area shows the information of the physical location of the equipment, previously introduced in the
configuration software.
ĚͿ
CURRENT NETWORK SETTINGS
Shows the current network configuration of the equipment.
ĞͿ
FACTORY RESET
ATTENTION: This button can perform a factory reset of the equipment. When pressed it will indicate
that all settings will be reset to default and you can confirm or abort.
ĨͿ
NETWORK CONFIGURATION BUTTON
The network configuration button enters into the equipment's network configuration menu.
NOTE: You must press the
OK button present in the numbers keyboard, as shown in the following picture,
to save changes in the configuration.
ŐͿ
DATE AND TIME SETTINGS/ IDENTIFY EQUIPMENT
It allows you to set the date and time manually.
NOTE: When linking the equipment to the Configuration software, the equipment will be automatically
synchronized with the PC's date and time.
When the selected equipment is an Extension unit (not the number 1), this button will change and allow
you to identify the equipment visually. When pressing the button, the frontal led light of the selected
item will blink for a few seconds.
ŚͿ
DISCOVER / UNLINK EQUIPMENT
The discover button searches for all the Extension units connected in the network. The equipment units
found will be shown in the system's equipment list buttons.
When the selected equipment is an Extension unit (not the number 1), this button will change and allows
you to unlink an equipment from the system.
ϰ
CONNECTION AND SETUP
ϰ͘ϭ
EMERGENCY SUPPLY SYSTEM
The equipment requires an external emergency power supply to work as an EN 54 voice evacuation
system. This power supply system must manage the battery charge and monitor the status of the external
batteries that will provide the required power in case of loss of normal power supply. The requirements
Picture 40: Network Configuration Window
Page
35
sur
51
ĐͿ
LOCATION IDENTIFIER
This area shows the information of the physical location of the equipment, previously introduced in the
configuration software.
ĚͿ
CURRENT NETWORK SETTINGS
Shows the current network configuration of the equipment.
ĞͿ
FACTORY RESET
ATTENTION: This button can perform a factory reset of the equipment. When pressed it will indicate
that all settings will be reset to default and you can confirm or abort.
ĨͿ
NETWORK CONFIGURATION BUTTON
The network configuration button enters into the equipment's network configuration menu.
NOTE: You must press the
OK button present in the numbers keyboard, as shown in the following picture,
to save changes in the configuration.
ŐͿ
DATE AND TIME SETTINGS/ IDENTIFY EQUIPMENT
It allows you to set the date and time manually.
NOTE: When linking the equipment to the Configuration software, the equipment will be automatically
synchronized with the PC's date and time.
When the selected equipment is an Extension unit (not the number 1), this button will change and allow
you to identify the equipment visually. When pressing the button, the frontal led light of the selected
item will blink for a few seconds.
ŚͿ
DISCOVER / UNLINK EQUIPMENT
The discover button searches for all the Extension units connected in the network. The equipment units
found will be shown in the system's equipment list buttons.
When the selected equipment is an Extension unit (not the number 1), this button will change and allows
you to unlink an equipment from the system.
ϰ
CONNECTION AND SETUP
ϰ͘ϭ
EMERGENCY SUPPLY SYSTEM
The equipment requires an external emergency power supply to work as an EN 54 voice evacuation
system. This power supply system must manage the battery charge and monitor the status of the external
batteries that will provide the required power in case of loss of normal power supply. The requirements
Picture 40: Network Configuration Window
Page
35
sur
51
ĐͿ
LOCATION IDENTIFIER
This area shows the information of the physical location of the equipment, previously introduced in the
configuration software.
ĚͿ
CURRENT NETWORK SETTINGS
Shows the current network configuration of the equipment.
ĞͿ
FACTORY RESET
ATTENTION: This button can perform a factory reset of the equipment. When pressed it will indicate
that all settings will be reset to default and you can confirm or abort.
ĨͿ
NETWORK CONFIGURATION BUTTON
The network configuration button enters into the equipment's network configuration menu.
NOTE: You must press the
OK button present in the numbers keyboard, as shown in the following picture,
to save changes in the configuration.
ŐͿ
DATE AND TIME SETTINGS/ IDENTIFY EQUIPMENT
It allows you to set the date and time manually.
NOTE: When linking the equipment to the Configuration software, the equipment will be automatically
synchronized with the PC's date and time.
When the selected equipment is an Extension unit (not the number 1), this button will change and allow
you to identify the equipment visually. When pressing the button, the frontal led light of the selected
item will blink for a few seconds.
ŚͿ
DISCOVER / UNLINK EQUIPMENT
The discover button searches for all the Extension units connected in the network. The equipment units
found will be shown in the system's equipment list buttons.
When the selected equipment is an Extension unit (not the number 1), this button will change and allows
you to unlink an equipment from the system.
ϰ
CONNECTION AND SETUP
ϰ͘ϭ
EMERGENCY SUPPLY SYSTEM
The equipment requires an external emergency power supply to work as an EN 54 voice evacuation
system. This power supply system must manage the battery charge and monitor the status of the external
batteries that will provide the required power in case of loss of normal power supply. The requirements
Picture 40: Network Configuration Window
Page
35
sur
51
ĐͿ
LOCATION IDENTIFIER
This area shows the information of the physical location of the equipment, previously introduced in the
configuration software.
ĚͿ
CURRENT NETWORK SETTINGS
Shows the current network configuration of the equipment.
ĞͿ
FACTORY RESET
ATTENTION: This button can perform a factory reset of the equipment. When pressed it will indicate
that all settings will be reset to default and you can confirm or abort.
ĨͿ
NETWORK CONFIGURATION BUTTON
The network configuration button enters into the equipment's network configuration menu.
NOTE: You must press the
OK button present in the numbers keyboard, as shown in the following picture,
to save changes in the configuration.
ŐͿ
DATE AND TIME SETTINGS/ IDENTIFY EQUIPMENT
It allows you to set the date and time manually.
NOTE: When linking the equipment to the Configuration software, the equipment will be automatically
synchronized with the PC's date and time.
When the selected equipment is an Extension unit (not the number 1), this button will change and allow
you to identify the equipment visually. When pressing the button, the frontal led light of the selected
item will blink for a few seconds.
ŚͿ
DISCOVER / UNLINK EQUIPMENT
The discover button searches for all the Extension units connected in the network. The equipment units
found will be shown in the system's equipment list buttons.
When the selected equipment is an Extension unit (not the number 1), this button will change and allows
you to unlink an equipment from the system.
ϰ
CONNECTION AND SETUP
ϰ͘ϭ
EMERGENCY SUPPLY SYSTEM
The equipment requires an external emergency power supply to work as an EN 54 voice evacuation
system. This power supply system must manage the battery charge and monitor the status of the external
batteries that will provide the required power in case of loss of normal power supply. The requirements
Picture 40: Network Configuration Window