NAPCO Gemini GEM-P816 Programming Instructions Manual - page 8
X
GEM-P816 Programming Instructions
L
NAPCO Security Systems
!
Page 8
WI995C 2/04
E
A
SY M
E
NU D
R
IVEN
PRO
G
RA
M
M
O
DE
Enable Burg Output Chirp on KeyFob?
•
Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.
•
Press the PRIOR/NO button to continue.
NOTE:
The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.
Enable SIA CP-01 Features?
•
Press the NEXT/YES button to enable.
•
Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms.
NOTE:
Do not
enable unless reporting, otherwise system trouble
Fail to Communicate
may occur.
Number of Keypads in Area 1
•
Enter the total number of Keypads to be installed in Area 1.
•
Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.
Press
U
to save. Press the NEXT/YES button to proceed.
NOTE:
Area 2 keypads must be assigned in Direct Address Programming. See Keypad Options.
Central Station Receiver 1 Telephone Number
•
Enter telephone number of up to 16 digits.
•
Press
1
through
9
for digits 1–9;
G
0
for a zero and
0
for a blank (•).
•
Press
G
1
through
G
5
for letters B–F, respectively.
•
Pre-Dial Delay = “D” (
G
4
); Dial-Tone Detection = “E” (
G
5
).
•
Press
U
to save and press the NEXT/YES button to proceed.
NOTE:
Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming.
See CS Receiver Options.
Central Station Receiver 1 Account Number
•
Enter an account number of up to four digits.
•
Press
0
through
9
for digits 0–9, and
G
0
for a blank (•).
•
Press
U
to save and press the NEXT/YES button to proceed.
NOTE:
Central Station Receiver 2 and 3 Account Numbers
must be entered in Direct Address Programming.
See CS
Reporting Options.
Central Station Receiver 1 Format
•
From the table at the right enter the receiver format.
•
Press
0
through
9
, and
G0
for blank (•).
•
Press
G1
through
G4
for letters B–E.
•
Press
U
to save and press the NEXT/YES button to proceed.
Enter User Codes
(Press
R
to set cursor.)
For default program, enter up to 32 User Codes, with Area 1 and Area 2 Options.
•
Press the (
R
) button once to set the cursor to the User Code.
•
Press
0
through
9
to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
•
Press
R
to set the cursor to the Area 1 Options Level. Refer to the table below for available op-
tions. For Area 2 Options, press the
R
button once again.
•
If “Enable Global Ambush Code” (Address 0720) is enabled and “Global Ambush Code” (Address 1054) is
not
left blank (•),
do not
program the
first two digits of ANY User Code the same as the “Global Ambush Code”.
•
Press
U
to save.
Note:
Duplicate User Codes are not allowed; therefore a duplicate Code entered in the LCD Window will erase when
U
is
pressed. To proceed to the next User Code, press
R
to set the cursor to the User Number and change it using the number buttons. Press
the NEXT/YES button to proceed.
(Direct Entry)
Cen tral Ph one #
(Direct Entry)
Central Station
Account # (____)
DATA
ENTRY
CS RECEIVER 1 FORMAT
•
(blank)
Ademco Slow, Silent Knight
Slow
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
B
SIA
C
Ademco Point ID
E
Pager
(Direct Entry)
S e e W I f o r I n f o
R c v r F o r m a t ( 0 )
E n t e r u s e r c o d e
U 0 1 1 2 3 - 9 -
User# User Code Area 1 Area 2
OPTION
ENABLED
Disabled
Arm/Disarm
Arm Only
Service
Access
Ambush
* User Program
L
R
blank(•) blank
blank(•)
1
blank(•)
2
blank(•)
3
blank(•)
4
blank(•)
5
DATA ENTRIES
blank(•) Add 8
USER AREA OPTIONS
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
AREA 1
OPTIONS
AREA 2
OPTIONS
Example:
Program a code of “2222” for user
02, with area 1 options of “Arm/Disarm” and
“User Program”. Enter “2222” for a user code,
“• (blank) 9” for area 1 options and “• (blank) •
(blank)” for area 2 options.
(Direct Entry)
# A rea 1 K eypads
Ent er # KP s 01
(Press YES or NO)
Enable SIA CP-01?
Y/N
(Press YES or NO)
Enable Burg Out
Chirp? Y/N