Summary of EDC-120P
Page 1
Flashlight user guide edc- 85p or 120p copyright 2007 by novatac, inc. All rights reserved july 2007.
Page 2: Flashlight User Guide
Flashlight user guide novatac™ edc- 85p or novatac™ 120p copyright 2007 by novatac, inc. All rights reserved july 2007 congratulations on your purchase of the edc-85p or 120p flashlight, the finest user programmable flashlight available! The edc is your best-of-class everyday carry pocket flashlight...
Page 3: Contents
Contents 1. Quick start 2. User guide 3. Brightness settings 4. The options menu 5. Resets 6. Low battery indication 7. Installing a new battery. 8. Hi temperature indication 9. Cleaning and maintenance 10. Warnings 11. Factory default settings 12. Specifications 13. Primary features 14. Settable op...
Page 4: 2. User’S Guide.
2. User’s guide. Using the single push button: the single push button is used to turn the light on or off, and access other functions. The following concepts are important to understand the operation of your light: click: a quick push and release of the button lasting less than one third of a second...
Page 5: 3. Brightness Settings.
3. Brightness settings. The light has 21 or 22 brightness levels and 3 signal levels available. Four of these are preset at the factory. The 4 settings are called primary, secondary, minimum and maximum. Any of the 22 brightness levels may be assigned to any of the preset settings. The 3 signal leve...
Page 6: Levels:
Is reached. 8. Do not turn the light off unless you want to save the setting. 9. Turn the light off to remember the brightness or signal level for this preset. If there is insufficient power to remember the setting, the light will flash rapidly for 2 seconds then turn off. The selected changes will ...
Page 7: To Enter The Options Menu:
If the button is not pressed for 10 seconds, an unknown command is entered, or the button is not held until the light turns off, the light will exit the options menu unchanged. The error flash sequence of six rapid flashes will be displayed and the light will return to the last setting accessed. To ...
Page 8: Option 2: Emergency Sos
Option 2: emergency sos (…---…) the sos option flashes the international emergency sos signal (dot, dot, dot, dash, dash, dash, dot, dot, dot). Setting it once enables it. To stop the sos signal, turn the light off. If the automatic turn-off option is enabled, the sos signal will turn off after 5 mi...
Page 9: Option 6: Automatic Turn Off
Option 5: automatic button lock (three rapid flashes) the automatic button lock option locks the light off after it has been off for five (5) minutes. If the button is pressed while the light is locked, it will flash three times and remain off. To release the automatic button lock, triple-click the ...
Page 10: Option 8: Tactical Momentary
Option 8: tactical momentary (short-short-long flash) the tactical momentary option provides a pure momentary mode of operation. When the button is pressed, the light will be on. When released, the light will be off. Any desired configuration changes (such as forcing on to maximum) must be made befo...
Page 11: Battery-Detect-Reset
Of dim light. 4. The soft reset is complete. If the light is still unresponsive, remove the battery for two minutes, then reinstall. Battery-detect-reset battery-detect-reset will not change any personal settings. Required when changing to or from a rechargeable battery. A rechargeable battery must ...
Page 12: 6. Low Battery Indication.
Light’s settings will remain unmodified. If there is insufficient power to remember the factory settings you will see two seconds of very rapid flashing. The default settings will be restored but when the battery is changed or a soft reset is done the change will be forgotten. 6. Low battery indicat...
Page 13: 7. Installing A New Battery.
7. Installing a new battery. The light comes with a fresh battery installed from the factory. To replace the battery, unscrew the battery compartment at the head or the button cap. Insert a new battery into the battery compartment so the positive terminal is toward the front of the light. Be sure bo...
Page 14: 10. Warnings.
Recessed contacts should be cleaned in a counter-clockwise direction, while springs should be cleaned in a clockwise direction to prevent snagging the swab. Be sure to remove any cotton fibers that may be left behind. The exterior can be cleaned with a mild soap and water. Rinse well and dry with a ...
Page 15: 12. Specifications:
12. Specifications: • input voltage: 1.8v to 4.5v • light source: white led • maximum light output: 85 or 120 lumens • regulation: constant power regulation with tint control™ • battery pack: 1xcr123a lithium-manganese dioxide • runtimes: see factory default settings • housing: aerospace aluminum, m...
Page 16
15. Battery configurations supported by the power supply. Primary cells (non-rechargeable) • li-fes2: 2 cells (3.3) • li-mno2: 1 cell (3.2v) • li-socl2: 1 cell (3.6v) • alkaline: 2 cells (3.3v) secondary cells (rechargeable) • li-ion: 1 cell (4.2v) • nicad: 2 cells (2.5v) • nimh: 2 cells (2.6v) batt...