Electric fireplace heater i n s t r u c t i o n m a n u a l m870p-28adc ndf-65nb-1 attention: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you read all instructions..
2 s a f e t y i n s t r u c t i o n s important please note: when you open the carton carefully check the unit and make sure there are no damages. If you have any problems with the unit, with how the various functions work or with hidden damages or missing parts please call 1-800-459-4409 (est) imme...
3 and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 8) do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 9) to discon...
4 at c is available for connecting three-blade grounding-type plugs to two-slot recep- tacles. The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is ava...
5 a s s e m b ly i n s t r u c t i o n s parts list: fireplace insert 1 a) top panel 1 b) base panel 1 c) front upper panel 1 d) left front upper panel 1 e) right front upper panel 1 f) left front lower panel 1 g) right front lower panel 1 h) left upper side panel 1 j) right upper side panel 1 k) le...
6 panel d together with 1 kd screw. Attach panel g and panel e together with 1 kd screw. Attach 2 x 3-holes wood connec- tors (q), one at each side, to panel c with 4 kd screws (2 screws for each 3-holes wood connector). Fig. A step 2: attach the left side panel (h and k) to the left front panel (d ...
7 step 5: attach the front upper panel (c ) to the left and right front upper panel (d and e) with 2 kd screws (1 screw on each side). See fig. E. Fig. E step 6: attach 2 plastic connectors on the upper side of front upper panel (c) with 4 kd screws (2 at each plastic con- nector). See fig f. Fig. F...
8 o p e r a t i o n fig. I step 10: tighten all kd screws. Step 11: carefully move the assembled unit to the desired location. The fireplace mantel should not be positioned in area exposed to direct sunlight. Wall anchor safety cable the use of wall anchor safety cable is highly recommended in order...
9 m a i n t e n a n c e on/off: press this button for main power and flame effect. The indicator light will turn on. See below for other control switches. 750w: for low heat function - press this switch while the on/off switch is in the on position for low heat. The indicator light will turn on. 150...
10 touch up repair paint paint directly on the mantel unit if necessary. Fig. A. Fig. A repairs if any problems are found with the original parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of the fol- lowing method. Tools required: e...
11 fig. B 2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches (10 mm) on the mantel. Each plastic connector needs 3 holes. See fig. C. Fig. C fig. D 3. Gently install the kd nuts into the drilled-holes with hammer as shown in fig. D. 4. Attach the plastic connector and lock in p...
12 fig. G fig. H 3. Attach the small l-bracket and lock in place with screws as shown in fig. H. Cleaning to clean unit first turn off controls on unit and unplug the unit from power source. To clean glass display panel; remove dust with clean dry cloth or to remove finger prints and other marks cle...
