1. DL manuals
  2. Racers Edge
  3. Battery Charger
  4. SureCharge 2000 LiPo
  5. Operating Manual

Racers Edge SureCharge 2000 LiPo Operating Manual

Manual is about: Balance Charger

Summary of SureCharge 2000 LiPo

  • Page 1

    Sure charge 2000 intelligent digital balance charger www.Racers-edge.Com.

  • Page 2

    Introduction thank you for purchasing the surecharge 2000 lipo balance charger by racers edge. This is a rapid charger with a high performance microprocessor and specialized operating software. Please read this entire operating manual completely and attentively before using this product, as it cover...

  • Page 3

    Special features safety programming the automatic charge termination program is based on the principle of the delta-peak volt- age detection. When the battery’s voltage exceeds the threshold, the charging process will end automatically. Automatic charging current limit you can set up the upper limit...

  • Page 4

    Lithium polymer balance charge connection diagram this diagram shows the correct way to connect your battery to the surecharge 2000 while charging in the balance charge mode only. Warning: failure to connect as shown in this diagram will damage this charger. The main battery leads must be connected ...

  • Page 5

    Warnings and safety notes these warnings and safety notes are particularly important. Please follow the instructions for maximum safety; otherwise the charger and battery can be damaged, or worse, can cause a fire. Never leave the charger unattended when it is connected to its power supply. If any •...

  • Page 6

    Warning and safety notes to avoid short circuit between the charge lead always connect the charge cable to the • charger first, then connect the battery. Reverse the sequence when disconnecting. Do not connect more than one battery pack to this charger at any one time. • never attempt to charge or d...

  • Page 7

    Warning and safety notes always refer to the manual by the battery manufacturer pertaining to charging methods, recom- mended charging current and charging time. Lithium cells should be charged according to the charging instruction provided by the manufacturer, strictly. Special attention should be ...

  • Page 8

    Navigation and programming as default this charger will be set to typical user settings when it is connected to a 12v battery for the first time. The screen displays the following information in sequence and the user can change the parameter on each screen. If you need to alter the parameter value i...

  • Page 9

    Navigation and programming there is a 3-pin port on the left of the charger used as usb interface or temperature sensor port. If the screen displays temperature, you can use the optional temperature probe to connect to the surface of the battery. If it is set as the usb port, you can connect the cha...

  • Page 10

    Lithium battery charging the left side of the first line shows the type of battery you choose. The value on the left of the second line of the charger is current user set, after setting the current and voltage, press start/enter key for more than 3 seconds to start the process. (charge current: 0.1-...

  • Page 11

    Lithium battery charging fast charge mode charging current will become lower when it progress to the end of charging. A specific cv process will be reduced to end the charging process earlier. In fact, the charging current will goes to 1/5 when the charging process comes to 1/10. Charging capacity w...

  • Page 12

    Voltage balancing and monitoring in the discharge process the processor monitors the voltage of each cell when the battery packs during “storage” and -discharging” process. To achieve this feature, plug each battery to the charger individually. If voltage of any cell is abnormal, the sc2000 will sho...

  • Page 13

    Cycling of nicd/nimh battery you can set up sequence on the left and the number of cycles on the right. You can balance, refresh and break-in the battery with this function you can set a temporary cool-off procedure in the user’s setting. Range of the cycle number is 1-5. Press batt type/stop key to...

  • Page 14

    Data storage program for your convenience the sc2000 has a data storage and load program. It can store five battery data representing the respective specifications of batteries. You can call back the data when charging or discharging without setting up the program again. Press start/enter key to mak...

  • Page 15

    Programming information it comes to the final voltage when the program ended. 3-pin connector is selected to be the usb port. The external temperature is displayed when the temperature probe is used. Present input voltage. The battery is connected with each port through cable; you can check voltage ...

  • Page 16

    Warning and error information the voltage is higher than which is set. Please check the number of cells in the battery pack. Voltage of one cell in the battery pack is too low, please check the voltage of each cell voltage of one cell in the battery pack is too high; please check the voltage of each...

  • Page 17

    Www.Racers-edge.Com.