Raleigh Pedelec Groove* User Manual - page 254

English–

4

0 276 001 X45 | (28.9.11)

Bosch eBike Systems

Adjusting the Assistance Mode

The level of assistance of the eBike drive when 

pedaling can be adjusted via the drive HMI.

Note: 

For individual versions, it is possible that 

the the assistance mode is pre-set and cannot 

be changed. It is also possible that less modes 

are available for selection than listed here.

A maximum of four assistance modes are avail-

able:

To 

change the assistance mode

, press the 

“mode”

 button 

4

 until the desired mode is dis-

played in indicator 

f

.

While using the start-assistance function, indi-

cation 

f

 goes out; the set assistance mode is 

stored.

Adjusting the Assistance Level

In the set assistance mode, the assistance level 

can be adjusted anytime, even during riding.

Note: 

For individual versions, it is possible that 

the assistance level is pre-set and cannot be 

changed.

A maximum of three assistance levels as well as 

the assistance shut-off are possible.

To 

increase the assistance level

, press the 

button 

6

 until the desired level is displayed in in-

dicator 

c

.

To 

decrease the assistance level

, press the 

button 

7

 until the desired level is displayed in in-

dicator 

c

.

In assistance level 

“0”

, the drive is switched off. 

The eBike can be operated as a normal bicycle 

through pedaling.

While using the start-assistance function, indica-

tion 

c

 goes out; the set assistance level is stored.

Switching Start-assistance On/Off

Start-assistance can be used for additional sup-

port on the first meters when starting is difficult 

(e.g., at a traffic light or when starting uphill). It 

can also be used as a pushing aid when in the 

lowest gear.

f

The start-assistance function may only be 

used when starting or pushing the eBike. 

Danger of injury when the wheels of the 

eBike do not have ground contact while using 

the start-assistance function.

To 

activate

 the start-assistance function, press 

the  

button 

6

 longer than 1 second and con-

tinue to hold. The eBike drive is activated, indi-

cator 

d

 flashes and indicators 

c

, 

e

 and 

f

 go out.

Start-assistance is 

switched off

 as soon as any 

of the following points occur:

– You release button 

6

,

– You press another button on the drive HMI,

– You pedal in forward or quickly in backward 

direction,

– The wheels of the eBike are blocked (e.g., 

through braking or running against an ob-

struction),

– After achieving a speed of 16 km/h.

Switching the Lighting On/Off

Depending on country-specific regulations, two 

lighting versions are possible:

– The front light, rear light and display lighting 

can be switched on and off at the same time 

via the drive HMI.

– Only the display lighting can be switched on 

and off; the front and rear light of the eBike 

are independent of the drive HMI.

“ECO”

: Effective assistance at max-

imum efficiency for maximum cruis-

ing range

“TOUR”

: Uniform assistance, for 

touring with long cruising range

“SPORT”

: Powerful assistance for 

sportive riding off road as well as 

for urban traffic

“SPEED”

: Maximum assistance, 

supporting highest cadence for 

sportive riding

Assistance 

degree* at:

Assistance level

Assistance mode

“1”

“2”

“3”

“ECO”

30 %

60 %

100 %

“TOUR”

45 %

80 %

120 %

“SPORT”

70 %

140 %

180 %

“SPEED”

90 %

160 %

250 %

* The assistance degree can vary for individual versions.

OBJ_BUCH-1557-001.book  Page 4  Wednesday, September 28, 2011  11:39 AM