- DL manuals
- Sam4s
- Cash Register
- ER-380
- Operation And Program Manual
Sam4s ER-380 Operation And Program Manual
Summary of ER-380
Page 1
Er-380 / er-380m electronic cash register au operation and program manual lyt z_w lsl j{ yv upgj hz og yln pz{l y all specifications are subject to change without notice jk68-60962q(rev.03) from er-380 v1.0, er-380m v1.0 up to er-380 v4.1, er-380m v4.1.
Page 2
Attention the product that you have purchased contains a rechargeable ni-mh battery. This battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of the battery into the municipal waste system. Check with your local solid waste officials...
Page 3: Precaution Statements
Precaution statements follow these safety, servicing and esd precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 safety precautions 1. Be sure that all built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstall...
Page 4
1-2 servicing precautions warning: first read the-safety precautions-section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning: an electrolytic capacitor installed with the wrong polarity mig...
Page 5: Contents
Er-380 / er-380m electronic cash register au contents • i contents getting started 1 about the er-380 / er-380m ................................................................................................... 1 unpacking................................................................................
Page 6
Ii • contents er-380 / er-380m electronic cash register au code plu entry - multiplication ..............................................................................31 code plu entry - multiplication with decimal point ..............................................31 code plu entry - split prici...
Page 7
Er-380 / er-380m electronic cash register au contents • iii x/z mode 71 introduction ............................................................................................................................. 71 x/z reports .............................................................................
Page 8
Iv • contents er-380 / er-380m electronic cash register au system option programming.................................................................................................104 program 30 - system option programming ............................................................104 system optio...
Page 9
Er-380 / er-380m electronic cash register au contents • v group programming .............................................................................................................. 156 program 900 - group status programming ............................................................. 156 prog...
Page 11: Getting Started
Er-380 / er-380m electronic cash register au getting started • 1 getting started about the er-380 / er-380m the er-380 / er-380m is offered in two different versions. • the er-380 / er-380m features a 44-position keyboard with traditional raised keys. This keyboard will accommodate up to 12/16 nlu k...
Page 12: Unpacking
2 • getting started er-380 / er-380m electronic cash register au unpacking 1. Unpack and unwrap the cash register. 2. Located in the packing are the following items: • 1 roll of paper, • 2 sets of control keys, • operation and program manual, 3. Remove the cardboard protectors from the cash drawer. ...
Page 13
Er-380 / er-380m electronic cash register au getting started • 3 2. Push the blue cap lever and then lift up to open the paper cover..
Page 14
4 • getting started er-380 / er-380m electronic cash register au 3. Ensure that the paper is being fed from the bottom of the roll. 4. Put the leading edge of the paper over the printer 5. Close the paper cover slowly until it locks firmly.
Page 15
Er-380 / er-380m electronic cash register au getting started • 5 6. Passing the leading edge of the paper through the cutter slot. Tear off the excess paper. Replace the printer cover. ※ if you wish to use the printer to print a sales journal or electronic journal, insert the paper into the paper ta...
Page 16: Basic Features and Functions
6 • getting started er-380 / er-380m electronic cash register au basic features and functions standard hardware • display => er-380m lcd model: 2 line, 16 character liquid crystal display and ten position rear displays with a rear pop up display standard. => er-380 vfd model: ten position front and ...
Page 17
Er-380 / er-380m electronic cash register au getting started • 7 front display vfd model - er-380 the er-380 comes with a ten position front display. Annotations on the display window include: • rpt, where a counter appears when the same item is multiplied or repeated. • the amount area shows the am...
Page 18
8 • getting started er-380 / er-380m electronic cash register au negative entry rc pt off void shift cler k rpt amount subtotal amount rpt rcpt off clerk void shift total of sale amount rpt rc pt off cler k void sh ift numbered error conditions amount rpt rcpt off clerk void shift.
Page 19: Warning!
Er-380 / er-380m electronic cash register au getting started • 9 lcd model - er-380m the er-380m comes with a liquid crystal screen, allowing you to view up to 2 lines of information with up to 16 characters per line. The display is backlit to provide excellent visibility, regardless of lighting con...
Page 20
10 • getting started er-380 / er-380m electronic cash register au rear display - vfd the rear display is a 10 digit florescent display that allows your customer to monitor the transaction and view the sale total. The rear display can be lifted and turned for easy customer viewing. Rear display infor...
Page 21
Er-380 / er-380m electronic cash register au getting started • 11 total of sale numbered error conditions.
Page 22
12 • getting started er-380 / er-380m electronic cash register au error code table e00 sequence error e22 req. Endorsement e01 plu no data e23 consol over e02 clerk error e24 req. Subtotal e03 amount count over e25 promo error e04 lan tran e26 check open e05 communication error e27 req. Password e06...
Page 23
Er-380 / er-380m electronic cash register au getting started • 13 control lock the control lock has 7 positions, accessed with 5 keys. Each ecr is shipped with two full sets of keys. Void p z x reg off s void use to void (correct) items outside of a sale. Off the register is inoperable. Reg use for ...
Page 24
14 • getting started er-380 / er-380m electronic cash register au keyboards the er-380 / er-380m keyboard includes 44 key positions with the default legends and key assignments as shown below. This configuration has 16 keyboard nlu locations. The keyboard legend label can be replaced by removing the...
Page 25: Memory Clear
Er-380 / er-380m electronic cash register au getting started • 15 memory clear memory all clear (ram clear) caution: the procedures described in this area are security sensitive. Clearing all or parts of the er-380/er-380m memory may cause damage or loss to the program. Do not share this information...
Page 26
16 • getting started er-380 / er-380m electronic cash register au initial clear (status clear) caution: do not share this information with unauthorized users. Distribute the p-mode key only to those you may want to perform this function. The initial clear function allows you to exit any register act...
Page 27: Operating Instructions
Er-380 / er-380m electronic cash register au operating instructions • 17 operating instructions function key descriptions keys are listed in alphabetical order. Some of the keys described below are not included on the default keyboard. See “function key assignment programming” to add or change progr...
Page 28
18 • operating instructions er-380 / er-380m electronic cash register au keyboard legend description charge (1 - 8) or eftpos use to finalize charge sales. Calculates the sale total including tax, finalizes the sale, and opens the cash drawer. Change computation is allowed by entering an amount befo...
Page 29
Er-380 / er-380m electronic cash register au operating instructions • 19 keyboard legend description guest # use to enter the count of guests served as part of a guest check. Inactive use to inactivate the key on the keyboard with warning/error message. Level (1 - 2) use to switch between different ...
Page 30
20 • operating instructions er-380 / er-380m electronic cash register au keyboard legend description tare tares are container weights. If you are using the scale function, you can preset up to 5 different tare weights. The tare can be subtracted automatically when a specific plu is registered, or ma...
Page 31: Clerk Sign-On/sign-Off
Er-380 / er-380m electronic cash register au operating instructions • 21 clerk sign-on/sign-off see "system option programming” to review your clerk options: • system option #2 allows you to select direct or code entry sign on. • system option #3 allows you to select stay-down or pop-up operation. D...
Page 32: Receipt On and Off
22 • operating instructions er-380 / er-380m electronic cash register au receipt on and off the receipt on/off function key may or may not be located on your keyboard. If the receipt on/off key is located on the keyboard 1. Press the receipt on/off key once to turn the receipt off. 2. Press the rece...
Page 33: Item Registrations
Er-380 / er-380m electronic cash register au operating instructions • 23 item registrations all registrations on er-380/er-380m are made into open or preset plus. • in place of traditional plu keys, some plus are located directly on the keyboard. • when more items or categories are needed than the n...
Page 34
24 • operating instructions er-380 / er-380m electronic cash register au keyboard plu entry - open price / preset price override 1. Enter an amount on the number pad. Do not use the decimal key. For example, for $2.99, enter: 2 9 9 2. Press a plu. For example, press plu 1: 1 receipt example: thank-y...
Page 35
Er-380 / er-380m electronic cash register au operating instructions • 25 keyboard plu entry - repeat open or preset price plus can be repeated as many times as necessary by pressing the same plu again. The number of times the item is repeated is shown on the display. 1. Enter an amount on the number...
Page 36
26 • operating instructions er-380 / er-380m electronic cash register au keyboard plu entry - multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset p...
Page 37
Er-380 / er-380m electronic cash register au operating instructions • 27 keyboard plu entry - multiplication with decimal point if you are selling items by weight or by length etc., you can multiply a fraction of a unit. It is up to 3 digits after decimal places. 1. Enter the amount with the decimal...
Page 38
28 • operating instructions er-380 / er-380m electronic cash register au keyboard plu entry - split pricing when items are priced in groups, i.E. 3 for $1.00, you can enter the quantity purchased and let the register calculate the correct price. 1. Enter the quantity purchased, and then press the x/...
Page 39
Er-380 / er-380m electronic cash register au operating instructions • 29 code plu entry - open price if the preset status of a plu is set to n (no), the plu will operate as an open price plu. See "plu programming" in the "program mode programming" chapter to program plu descriptors and options. 1. E...
Page 40
30 • operating instructions er-380 / er-380m electronic cash register au code plu entry - preset price override if the override preset is set to y (yes), the plu is operating as a preset override plu. See "plu programming" in the "program mode programming" chapter to program plu descriptors and opti...
Page 41
Er-380 / er-380m electronic cash register au operating instructions • 31 code plu entry - multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset plus....
Page 42
32 • operating instructions er-380 / er-380m electronic cash register au code plu entry - split pricing when items are priced in groups, i.E. 3 for $1.00, you can enter the quantity purchased and let the register calculate the correct price. 1. Enter the quantity purchased, and then press the x/time...
Page 43
Er-380 / er-380m electronic cash register au operating instructions • 33 barcode plu entry - open price, single item 1. Press 1 on the number pad, and then press the x/time key. 1 x/ ti me 2. Scan barcode of the item. 3. Enter an amount on the number pad. Do not use the decimal key. For example, for...
Page 44
34 • operating instructions er-380 / er-380m electronic cash register au barcode plu entry - preset price override, single item 1. Press 1 on the number pad, and then press the x/time key. 1 x/ ti me 2. Scan barcode of the item. 3. Enter an amount on the number pad. Do not use the decimal key. For e...
Page 45
Er-380 / er-380m electronic cash register au operating instructions • 35 modifier key pressing a modifier key alters the next plu registered, either by changing the code number of the plu so that a different item is registered, or by just adding the modifier descriptor and registering the same plu. ...
Page 46
36 • operating instructions er-380 / er-380m electronic cash register au price level key if you choose to use the price level feature, you must allocate memory for each level. See "memory allocation" in the "service mode programming" chapter. Note that the default program selects one price level. Yo...
Page 47
Er-380 / er-380m electronic cash register au operating instructions • 37 promo the promo key allows you to account for promotional items, as in "buy two, get one free". Pressing this key will remove an item's cost from the sale, and the promo item will not be added to the plu sales total, but it is ...
Page 48
38 • operating instructions er-380 / er-380m electronic cash register au waste the waste key allows control of inventory by accounting for items that must be removed from stock due to spoilage, breakage or mistakes. Press the waste key before entering wasted items, and then press the waste key again...
Page 49: Percent Key Operations
Er-380 / er-380m electronic cash register au operating instructions • 39 percent key operations a total of five % functions are available. %1 is located on the default keyboard. Your keyboard may be different. More or less % keys may be located on the keyboard, or they may be located on one of the f...
Page 50
40 • operating instructions er-380 / er-380m electronic cash register au preset percent discount on an item in this example the %1 function is programmed with percentage, negative, item, preset and overridable witha rate of 10%.Please refer to % (1 ~ 5) (discounts or surcharges) in function key prog...
Page 51
Er-380 / er-380m electronic cash register au operating instructions • 41 preset percent discount on sale total in this example the %1 function is programmed with percentage, negative, sale, preset and overridable witha rate of 10%.Please refer to % (1 ~ 5) (discounts or surcharges) in function key p...
Page 52
42 • operating instructions er-380 / er-380m electronic cash register au dollar amount discount on sale when programmed as "amount", "sale", "open" and "negative", a % key will deduct an amount from a sale. Also, depending upon programming: • you may be allowed to enter only one discount in a sale, ...
Page 53
Er-380 / er-380m electronic cash register au operating instructions • 43 return merchandise registrations if you wish to return or refund an item press return, then re-enter any item. You can return merchandise as part of a sale, or you can return merchandise as a separate transaction and return cas...
Page 54: Voids and Corrections
44 • operating instructions er-380 / er-380m electronic cash register au voids and corrections error correction (void last item) this function corrects the last item entered. 1. Register the item you wish to sell. 2. Press the error corr key: error corr receipt example: thank-you call again date 15/...
Page 55
Er-380 / er-380m electronic cash register au operating instructions • 45 cancel the cancel key allows you to stop any transaction. Anything registered within the transaction before the cancel key is pressed is automatically corrected. The cancel key can be inactivated through programming, see "funct...
Page 56: No Sale Operations
46 • operating instructions er-380 / er-380m electronic cash register au no sale operations open drawer the #/no sale key will open the cash drawer when you have not already started a transaction. The no sale function can be disabled or placed under manager control through programming, see "function...
Page 57
Er-380 / er-380m electronic cash register au operating instructions • 47 received on account operations you can use one of the received on accountfunctions (ra1-ra3) to accept cash or checks into the cash drawer when you are not actually selling merchandise. For example, use received on accountto ac...
Page 58: Paid Out Operations
48 • operating instructions er-380 / er-380m electronic cash register au paid out operations you can use the paid out function (po1-po3) to track cash or checks paid out or to record loans from the cash drawer. 1. Press one of the paid out keys (po1-po3) po1 2. Enter the amount of cash paid out, pre...
Page 59: Subtotaling A Sale
Er-380 / er-380m electronic cash register au operating instructions • 49 subtotaling a sale 1. Register the items you wish to sell. 2. Press sbtl. The subtotal will display with the message "sub" indicated on the rear display. Sbt l the subtotal can be printed if the system option is set. See "print...
Page 60: Totaling and Tendering
50 • operating instructions er-380 / er-380m electronic cash register au totaling and tendering there are ten tender functions available to categorize sales. Cash and check are individual keys on the keyboard totaling a cash sale 1. Register the items you wish to sell. 2. To total a cash sale, press...
Page 61
Er-380 / er-380m electronic cash register au operating instructions • 51 tendering a cash sale 1. Register the items you wish to sell. 2. Enter the amount tendered by the customer. For example, for $20.00 enter: 0 0 0 2 3. Press cash: cash 4. The display will indicate the total amount of the cash te...
Page 62
52 • operating instructions er-380 / er-380m electronic cash register au totaling a charge (eftpos) sale use the charge keys to track charge or credit card sales. See "function key programming" in the "program mode programming" chapter to change the descriptors for the charge tender functions. For e...
Page 63
Er-380 / er-380m electronic cash register au operating instructions • 53 cash out within a charge (eftpos) sale cash out within a charge (eftpos) sale may or may not be allowed. See "function key assignment programming" in the "service mode programming" chapter to assign cash out key. 1. Register th...
Page 64
54 • operating instructions er-380 / er-380m electronic cash register au check cashing check cashing means exchanging cash for a check. If you wish to cash checks, you must place a chkcash key on the keyboard. See "function key assignment" in the "program mode programming" chapter. 1. Enter the amou...
Page 65
Er-380 / er-380m electronic cash register au operating instructions • 55 post tender post tendering means computing change after the sale has been totaled and the drawer is open. This feature is useful when a customer changes the amount of the tender or when a "quick change artist" confuses a clerk....
Page 66
56 • operating instructions er-380 / er-380m electronic cash register au table management and clerk interrupt operations overview the er-380 / er-380m can employ a manual previous balance, hard check (monthly accounts), or soft check (restaurant bill) system. (you must select hard or soft check post...
Page 67
Er-380 / er-380m electronic cash register au operating instructions • 57 soft check - restaurant style billing opening a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. If required, enter the ...
Page 68
58 • operating instructions er-380 / er-380m electronic cash register au adding to a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: t able 3 2. Register the next items you wish ...
Page 69
Er-380 / er-380m electronic cash register au operating instructions • 59 paying a soft check without payment key required to close check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: t ab...
Page 70
60 • operating instructions er-380 / er-380m electronic cash register au taking deposits or account payments with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programmi...
Page 71
Er-380 / er-380m electronic cash register au operating instructions • 61 paying a soft check with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programming - payment” in...
Page 72
62 • operating instructions er-380 / er-380m electronic cash register au hard check - monthly account style billing opening a hard check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. Register the items...
Page 73
Er-380 / er-380m electronic cash register au operating instructions • 63 paying a hard check without payment key required to close check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 2. Pay the balance, as you would normally tender a transaction, with cash, check, or on...
Page 74
64 • operating instructions er-380 / er-380m electronic cash register au paying a hard check with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programming - payment” in...
Page 75
Er-380 / er-380m electronic cash register au operating instructions • 65 sample of hard check postings printed on an optional cbm-820 printer example without payment key required to close check: date ___________ 15/01/2003 ____________ wed ____ check # _________________ #123 ____ pbal ______________...
Page 76: Scale Entry
66 • operating instructions er-380 / er-380m electronic cash register au scale entry direct scale entry place a product on the scale and access the scale function to display the weight on the cash register. Then make the appropriate entry; the plu must have "scaleable" status. 1. Place an item on th...
Page 77
Er-380 / er-380m electronic cash register au operating instructions • 67 automatic scale entry place a product on the scale and make the appropriate plu entry. The plu must be set with "auto scale status" & “scalable”. 1. Place an item on the scale. 2. Press a plu key, if the item is a preset item, ...
Page 78
68 • operating instructions er-380 / er-380m electronic cash register au manual tare weight entry 1. Place an item on the scale. 2. Enter the manual tare number, 5. Press the tare key: 5 t are 3. Enter the weight of the tare. For example, enter .01, press the tare key: 1 t are . 0 4. Press the scale...
Page 79
Er-380 / er-380m electronic cash register au operating instructions • 69 manual weight entry operators can make manual weight entries if the item has been programmed to accept them. You must use the decimal key to enter fractional manual weights. 1. Place an item on the scale. 2. Enter the weight us...
Page 81: X/z Mode
Er-380 / er-380m electronic cash register au x/z mode • 71 x/z mode introduction all management functions take place with the control lock in the x position. In this way only those with the correct key will have access to these functions. Some register operations may be programmed to require the con...
Page 82: X/z Reports
72 • x/z mode er-380 / er-380m electronic cash register au x/z reports system reports are divided into two basic categories: • x reports (include x1 and x2 reports) in x mode, which read totals without resetting • z reports (include z1 and z2 reports) in z mode, which read totals and reset them to z...
Page 83
Er-380 / er-380m electronic cash register au x/z mode • 73 report table report type report number report mode control lock position key sequence x1 x 1 – sbtl z1 z 1 – sbtl x2 x 201 – sbtl financial 1 z2 z 201 – sbtl x1 x 2 – sbtl z1 z 2 – sbtl x2 x 202 – sbtl time 2 z2 z 202 – sbtl x1 x 3 – sbtl z1...
Page 84
74 • x/z mode er-380 / er-380m electronic cash register au electronic journal table report type report number report mode control lock position key sequence print all ej 300 x x 300 -sbtl print ej cash 301 x x 301 -sbtl print ej check 302 x x 302 -sbtl print ej misc/t 303 x x 303 -sbtl print ej % 30...
Page 85
Er-380 / er-380m electronic cash register au x/z mode • 75 reset hard check (slip) line # (eprom v3.1 & later) if you want to reset hard check line # to 0, follow below sequence after turn control lock to z-mode. Program 10 - reset hard check line # programming 1. Reset all hard check line #. Cash 0...
Page 86: Cash Declaration
76 • x/z mode er-380 / er-380m electronic cash register au cash declaration if compulsory cash declaration is required, you must declare the count of the cash drawer prior to taking x or z financial and clerk reports. You can enter the cash drawer total in one step, or to facilitate the counting of ...
Page 87: Service Mode Programming
Er-380 / er-380m electronic cash register au service mode programming • 77 service mode programming overview the following procedures are done from the service mode menu: • program 20 - clear all sales totals • program 30 - clear grand total • program 40 - clear / delete plu file • program 50 - epro...
Page 88: Memory Allocation Scan
78 • service mode programming er-380 / er-380m electronic cash register au memory allocation scan 1. Turn the control lock to the s-mode to scan the allocated memory. 2. Enter 6 0, press the sbtl key. 0 sbt l 6 3. Press cash key. Cash pc online mode in er-380 / er-380m, there are no special commands...
Page 89: Memory Allocation
Er-380 / er-380m electronic cash register au service mode programming • 79 memory allocation nb. This will clear the memory! Program 60 - memory allocation programming 1. Turn the control lock to the s-mode. 2. To allocate memory, enter 6 0, and then press the sbtl key. 0 sbt l 6 3. Refer to the cha...
Page 90: Clear All Sales Totals
80 • service mode programming er-380 / er-380m electronic cash register au clear all sales totals program 20 - clear all sales totals 1. Turn the control lock to the s-mode. 2. To clear all sale totals, enter 2 0, and then press the sbtl key. 0 sbt l 2 clear grand total program 30 - clear grand tota...
Page 91
Er-380 / er-380m electronic cash register au service mode programming • 81 function key assignment programming function keys may be relocated, inactivated or changed with this program. For example, you may wish to place functions, such as previous balance and service that are not placed on the defau...
Page 92
82 • service mode programming er-380 / er-380m electronic cash register au function key codes - new version (er-380 eprom v2.1 & later / er-380m eprom v1.8 & later) code function code function code function code function 1 nlu 1 142 charge 1 168 level 1 194 rec on acct 2 ~117 nlu 117 143 charge 2 16...
Page 93
Er-380 / er-380m electronic cash register au service mode programming • 83 function key codes - old version (er-380 eprom v2.0 & earlier / er-380m eprom v1.7 & earlier) code function code function code function code function 1 nlu 1 37 charge 1 63 level 1 89 rec on acct 2 ~12 nlu 12 38 charge 2 64 l...
Page 94
84 • service mode programming er-380 / er-380m electronic cash register au rs232c serial port #1 communication options you must define the device that is attached to the rs-232c communications port, and the options for the device. The default is comm1 is set to pc polling program 80 - rs232c serial ...
Page 95
Er-380 / er-380m electronic cash register au service mode programming • 85 n1 option n2 value 7 end feeding line kp 0 - 20 7 8 initial feeding line slip 0 - 20 0 9 print line on guest check 0 - 50 0 (preset “0” is equivalant to 30 lines) 0 nci 10 scale type 1 cas 0 none 1 sam4s ellix10 2 sam4s ellix...
Page 96
86 • service mode programming er-380 / er-380m electronic cash register au er-380m rs232c serial port #2 communication options the er-380mincludes a standard second rs-232c port. The second port is set in the same manner as the first, using program 81: program 81 - rs232c serial port #2 communicatio...
Page 97: Program Mode Programming
Er-380 / er-380m electronic cash register au program mode programming • 87 program mode programming default programming • all keyboard plus are taxable, preset and override, without entry limits by default status programming of "400000000". • all system options are set to 0 in default programming, u...
Page 98
88 • program mode programming er-380 / er-380m electronic cash register au descriptor programming methods descriptors are programmable for plus, function keys, groups, clerks and the logo/messages. There are two methods available to program descriptors, the alpha overlay and descriptor code methods....
Page 99
Er-380 / er-380m electronic cash register au program mode programming • 89 descriptor code method if you customize your keyboard by covering key locations, or by installing double or quad size keys, or need lower case characters, symbles in the description, you will need to program descriptors using...
Page 100: Tax Programming
90 • program mode programming er-380 / er-380m electronic cash register au tax programming the er-380 / er-380m has the capability to support four separate taxes. Taxes can be calculated as either a straight percentage rate of between .001% and 99.999%, or a 60 break point tax table. Each tax may be...
Page 101
Er-380 / er-380m electronic cash register au program mode programming • 91 4. Enter 0 here for all taxes, unless if you are programming tax 4 as a canadian gst. If tax 4 is a canadian gst, enter the sum of the options below: option value = sum gst (tax 4) is taxable by rate 1? Yes = 1 no = 0 gst (ta...
Page 102: Plu Programming
92 • program mode programming er-380 / er-380m electronic cash register au plu programming all plus, whether they are registered by pressing a plu key on the keyboard, or by entering the plu number and pressing the plu key, have the same programming options. These options are set through separate pr...
Page 103
Er-380 / er-380m electronic cash register au program mode programming • 93 program 100 - plu status programming plus default to taxable by rate 1. I.E gst 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 1 0 0, press the sbtl key. 0 sbtl 0 1 3. Select the plu or plus you wish...
Page 104
94 • program mode programming er-380 / er-380m electronic cash register au plu status chart address program option value = sum plu is preset price? Yes = 0 no = 1 plu allows override of preset ? Yes = 0 no = 2 n1 plu is taxable by rate 1(gst)? Yes = 4 no = 0 plu is taxable by rate 2? Yes = 1 no = 0 ...
Page 105
Er-380 / er-380m electronic cash register au program mode programming • 95 address program option value = sum plu counter is not reset when a plu z report is done? Yes = 1 no = 0 n9 plu is preset override in mgr control? Yes = 2 no = 0 Údefault values have been highlighted in bold print.
Page 106
96 • program mode programming er-380 / er-380m electronic cash register au program 110 - plu auto tare programming note: if this program has been performed, please also see program 1400 - scale tare weight programming in program mode programming - miscellaneous programming for more detail. 1. Turn t...
Page 107
Er-380 / er-380m electronic cash register au program mode programming • 97 program 150 - plu group assignment programming each plu may report to any three levels of 20 groups. Group totals appear on reports, so that you can track sales of different types of items. A group can also be used to designa...
Page 108
98 • program mode programming er-380 / er-380m electronic cash register au program 200 - plu price/halo programming note: if price level in the memory allocation is set to 2, the 2 nd price level must be set as well. Price of level 2 may be $0.00. Before changing price of one of the level, original ...
Page 109
Er-380 / er-380m electronic cash register au program mode programming • 99 program 250 - plu stock amount programming with this program, you can add stock to the plu sales counters for plus you have designated as stock keeping plus. See “program 100 - plu status programming”. The stock number set he...
Page 110
100 • program mode programming er-380 / er-380m electronic cash register au program 300 - plu description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘n...
Page 111
Er-380 / er-380m electronic cash register au program mode programming • 101 program 350 - plu link programming plu link programming allows you to link a plu to another plu, so that registration of the first plu will automatically trigger registration of the linked plu. For example, you may wish to l...
Page 112
102 • program mode programming er-380 / er-380m electronic cash register au program 400 - plu delete programming note: to delete a plu, all totals for the plu must be cleared from z reports (including stock and plu reports.) 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 4 ...
Page 113
Er-380 / er-380m electronic cash register au program mode programming • 103 program 450 - plu mix & match programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 4 5 0, press the sbtl key. 0 sbt l 5 4 3. Select the plu you wish to program in one of the following ways: • ...
Page 114: System Option Programming
104 • program mode programming er-380 / er-380m electronic cash register au system option programming refer to the “system option table” to review the system options. Read each option carefully to determine if you wish to make any changes. Default value has been highlighted in bold print. Note: beca...
Page 115
Er-380 / er-380m electronic cash register au program mode programming • 105 system option table address system option value = sum beeper is active? Yes = 0 no = 1 1 % affect net sale? Yes = 0 no = 2 direct entry = 0 2 clerk sign on method is: code entry = 1 pop-up = 1 3 clerks are: stay down = 0 dra...
Page 116
106 • program mode programming er-380 / er-380m electronic cash register au address system option value = sum round up at 0.005 = 0 always round up = 1 12 percentage and tax calculations will: always round down = 2 round up at 0.005 = 0 always round up = 1 13 split price calculations will: always ro...
Page 117
Er-380 / er-380m electronic cash register au program mode programming • 107 address system option value = sum allow australian rounding on cash? Yes = 1 no = 0 22 allow z stock report? Yes = 0 no = 2 enter = 1 23 training mode exit = 0 enable electronic journal? Yes = 1 no = 0 prompt operator when e...
Page 118
108 • program mode programming er-380 / er-380m electronic cash register au address system option value = sum 31 price embedded barcode type? (0/1/2/3/4/7) (see note below) ( er-380 eprom v1.6; er-380m eprom v1.3) 0 new zealand round on subtotal (nb turn au rounding off first) ( er-380 eprom v2.1; e...
Page 119: Print Option Programming
Er-380 / er-380m electronic cash register au program mode programming • 109 print option programming refer to the “print option table” to review the print options. Read each option carefully to determine if you wish to make any changes. Default value has been highlighted in bold print. Note: because...
Page 120
110 • program mode programming er-380 / er-380m electronic cash register au print option table address print option value = sum print media totals on clerk report? Yes = 1 no = 0 1 print tax symbol? Yes = 0 no = 2 void/return totals will print on the financial report? Yes = 0 no = 1 2 audaction tota...
Page 121
Er-380 / er-380m electronic cash register au program mode programming • 111 address print option value = sum print gross total on the x financial report? Yes = 0 no = 1 10 print gross total on the z financial report? Yes = 0 no = 2 print the subtotal without tax on the receipt? Yes = 1 no = 0 combin...
Page 122
112 • program mode programming er-380 / er-380m electronic cash register au address print option value = sum print preamble message on the guest check? Yes = 1 no = 0 22 print postamble message on the guest check? Yes = 2 no = 0 print average items per customer on the financial report? Yes = 0 no = ...
Page 123
Er-380 / er-380m electronic cash register au program mode programming • 113 address print option value = sum 34 print check# line on the guest check (eprom v3.3) yes = 1 no = 0 Údefault values have been highlighted in bold print note 1: print option# 8 - users outside of the usa can designate a diff...
Page 124: Function Key Programming
114 • program mode programming er-380 / er-380m electronic cash register au function key programming three programs are used to program function keys: • program 70 - function key options programming is used to set each keys individual options • program 80 - function key descriptor programming is use...
Page 125
Er-380 / er-380m electronic cash register au program mode programming • 115 program 70 - function key options programming use program 70 to set options for function keys. Because of the differences inherent in function keys, individual options will be different. See the specific instructions for eac...
Page 126
116 • program mode programming er-380 / er-380m electronic cash register au program 80 - function key descriptor programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must se...
Page 127
Er-380 / er-380m electronic cash register au program mode programming • 117 program 90 - function key halo or percentage rate programming use program 90 to program a high amount lock out (halo) for a function key. Only specific keys require this program. For example, you can set a halo for the cash,...
Page 128
118 • program mode programming er-380 / er-380m electronic cash register au add check (cafeteria tray total) options - program 70 add cehck cash repeat for another function key n1 sbt l 0 7 n2 n3 address option value = sum key is inactive? Yes = 1 no = 0 compulsory before tendering? Yes = 2 no = 0 n...
Page 129
Er-380 / er-380m electronic cash register au program mode programming • 119 cancel (cancel a sale) options - program 70 canc el c ash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 ...
Page 130
120 • program mode programming er-380 / er-380m electronic cash register au cash options - program 70 cash cash n1 sbt l 0 7 n2 n3 repeat for another function key address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock positio...
Page 131
Er-380 / er-380m electronic cash register au program mode programming • 121 charge (1 ~ 8) options - program 70 charge cash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 n5 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x c...
Page 132
122 • program mode programming er-380 / er-380m electronic cash register au check (cheque) options - program 70 check c ash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x cont...
Page 133
Er-380 / er-380m electronic cash register au program mode programming • 123 check (cheque) cashing options - program 70 check cash c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no =...
Page 134
124 • program mode programming er-380 / er-380m electronic cash register au check (cheque) endorsement options - program 70 check endorse cash repeat for another function key n1 sbt l 0 7 n 2 address option value = sum key is inactive? Yes = 1 no = 0 print the amount of the check and endorsement mes...
Page 135
Er-380 / er-380m electronic cash register au program mode programming • 125 check # (bill or account no.) options - program 70 check# cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum key is inactive? Yes = 1 no = 0 required at start of sale? (compulsory for all s...
Page 136
126 • program mode programming er-380 / er-380m electronic cash register au currency conversion currency conversion rate - program 90 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 9 0, press the sbtl key. 0 sbt l 9 3. Enter the exchange rate of up to 7 digits (do not enter...
Page 137
Er-380 / er-380m electronic cash register au program mode programming • 127 drive thru / eat in / take out options - program 70 dr ive t hru cash n1 sbt l 0 7 n 2 repeat for another function key eat in cash n1 sbt l 0 7 n 2 repeat for another function key t ake out cash n1 sbt l 0 7 n 2 repeat for a...
Page 138
128 • program mode programming er-380 / er-380m electronic cash register au error correct options - program 70 error correct cash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 v...
Page 139
Er-380 / er-380m electronic cash register au program mode programming • 129 f/s tend options - program 70 f/s tend cash repeat for another function key n1 sbt l 0 7 n 2 n3 address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax ...
Page 140
130 • program mode programming er-380 / er-380m electronic cash register au guest (bill or account) options - program 70 guest c ash repeat for another function key n1 sbt l 0 7 address option value = sum required when opening a new check? Yes = 1 no = 0 before registering, enter a guest number? Yes...
Page 141
Er-380 / er-380m electronic cash register au program mode programming • 131 macro (1 ~ 10) options - program 70 mac ro c ash repeat for another function key n1 sbt l 0 7 address option value = sum n1 key is active in x control lock position only? (eprom v3.3) yes = 1 no = 0 Údefault values have been...
Page 142
132 • program mode programming er-380 / er-380m electronic cash register au modifier (1 ~ 5) options - program 70 mod cash repeat for another function key n1 sbt l 0 7 n 2 n3 address option value = sum key is active in x control lock position only? Yes = 1 no = 0 n1 modify plu#? Yes = 2 no = 0 print...
Page 143
Er-380 / er-380m electronic cash register au program mode programming • 133 #/ns (non add#/no sale) options - program 70 #/ns c ash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 address option value = sum no sale is inactive? Yes = 1 no = 0 no sale active in x control lock position only? Ye...
Page 144
134 • program mode programming er-380 / er-380m electronic cash register au paid out (1 ~ 3) options - program 70 p/o c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only yes = 2 no = 0 n1 validati...
Page 145
Er-380 / er-380m electronic cash register au program mode programming • 135 pbal options - program 70 previous balance cash n1 sbt l 0 7 repeat for another function key address option value = sum previous balance may be entered at any time? Yes = 1 no = 0 n1 previous balance required at the start of...
Page 146
136 • program mode programming er-380 / er-380m electronic cash register au promo options - program 70 pr omo cash repeat for another function key n1 sbt l 0 7 n2 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 taxable by ta...
Page 147
Er-380 / er-380m electronic cash register au program mode programming • 137 recd on acct (1 ~ 3) options - program 70 r/a c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 val...
Page 148
138 • program mode programming er-380 / er-380m electronic cash register au scale options - program 70 sc ale cash n1 sbt l 0 7 n2 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 allow manual ...
Page 149
Er-380 / er-380m electronic cash register au program mode programming • 139 service (bill or account) options - program 70 ser vice cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum compulsory non-add number before this key is used? Yes = 1 no = 0 print on receipt...
Page 150
140 • program mode programming er-380 / er-380m electronic cash register au subtotal options - program 70 subtotal cash repeat for another function key n1 sbt l 0 7 address option value = sum n1 key is inactive? Yes = 1 no = 0 Údefault values have been highlighted in bold print descriptor - program ...
Page 151
Er-380 / er-380m electronic cash register au program mode programming • 141 tare options - program 70 t are c ash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 using tare number...
Page 152
142 • program mode programming er-380 / er-380m electronic cash register au tax exempt options - program 70 tax exempt cash n1 sbt l 0 7 n2 repeat for another function key address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax ...
Page 153
Er-380 / er-380m electronic cash register au program mode programming • 143 tip (bill or account) options - program 70 t ip cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum percentage = 1 n1 type of tip is: amount = 0 key is inactive? Yes = 1 no = 0 key is active...
Page 154
144 • program mode programming er-380 / er-380m electronic cash register au validate options - program 70 valid cash repeat for another function key n1 sbt l 0 7 n2 address option value = sum er-380 (0-1) n1 enter port number. Enter 0 (zero) if validation is not used. Er-380m (0-2) 0 0 key is inacti...
Page 155
Er-380 / er-380m electronic cash register au program mode programming • 145 waste options - program 70 wast e c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is c...
Page 156
146 • program mode programming er-380 / er-380m electronic cash register au % (1 ~ 5) (discounts or surcharges) options - program 70 % cash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 n6 n5 address option value = sum amount = 1 apply an: percentage = 0 key is inactive? Yes = 2 no = 0 n1 %...
Page 157
Er-380 / er-380m electronic cash register au program mode programming • 147 descriptor - program 80 - refer to “program 80 - function key descriptor” preset % rate - program 90 % cash repeat for another function key sbt l 0 9 enter 5 digit rate or amount (see note b elow) note: if key is amount, ent...
Page 159: Clerk Programming
Er-380 / er-380m electronic cash register au program mode programming • 149 clerk programming clerks (which may be used as cashiers), have the following programming options. These options are set through separate programs: • program 800 - secret code programming determines the code that is used for ...
Page 160
150 • program mode programming er-380 / er-380m electronic cash register au program 800 - secret code programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 8 0 0, press the sbtl key. 0 sbtl 0 8 3. Enter the number of the clerk you wish to program; press the x/time key....
Page 161
Er-380 / er-380m electronic cash register au program mode programming • 151 program 801 - drawer assignment & training clerk programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 8 0 1, press the sbtl key. 1 sbt l 0 8 3. Enter the number of the clerk you wish to progra...
Page 162
152 • program mode programming er-380 / er-380m electronic cash register au program 810 - clerk description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ...
Page 163: Mix & Match Programming
Er-380 / er-380m electronic cash register au program mode programming • 153 mix & match programming mix & match tables have the following programming options. These options are set through separate programs: • program 600 - trip level programming • program 601 - price programming • program 610 - mix...
Page 164
154 • program mode programming er-380 / er-380m electronic cash register au program 600 - trip level programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 6 0 0, press the sbtl key. 0 sbt l 0 6 3. Enter the number of the m&m table you wish to program; press the x/time ...
Page 165
Er-380 / er-380m electronic cash register au program mode programming • 155 program 610 - mix & match description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must s...
Page 166: Group Programming
156 • program mode programming er-380 / er-380m electronic cash register au group programming 20 group totals are available to accumulate totals of individual plus that are assigned to each group. Each plu can be assigned to one, two or three different groups. • program 900 - group status programmin...
Page 167
Er-380 / er-380m electronic cash register au program mode programming • 157 program 910 - group descriptors programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ...
Page 168: Miscellaneous Programming
158 • program mode programming er-380 / er-380m electronic cash register au miscellaneous programming program 1500 - macro key sequence programming macros are special function keys that are used to execute a sequence of key depressions. For example, a macro might be used to execute a string of repor...
Page 169
Er-380 / er-380m electronic cash register au program mode programming • 159 program 700 - logo description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘...
Page 170
160 • program mode programming er-380 / er-380m electronic cash register au program 701 - financial report message programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must ...
Page 171
Er-380 / er-380m electronic cash register au program mode programming • 161 financial report message x message line x message line x message line 1 +plu ttl 29 credit tax4 57 chg7-in-d 2 -plu ttl 30 fd/s credit 58 chg8-in-d 3 adjst ttl 31 return 59 chg1 sales 4 nontax 32 error corr 60 chg2 sales 5 g...
Page 172
162 • program mode programming er-380 / er-380m electronic cash register au program 710 - clerk report message programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must sele...
Page 173
Er-380 / er-380m electronic cash register au program mode programming • 163 clerk report message x message line x message line x message line 1 net sale 25 credit tax3 49 chg4 sales 2 nontax 26 credit tax4 50 chg5 sales 3 gst sales 27 fd/s credit 51 chg6 sales 4 tax2 sales 28 return 52 chg7 sales 5 ...
Page 174
164 • program mode programming er-380 / er-380m electronic cash register au program 711 - macro name programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in...
Page 175
Er-380 / er-380m electronic cash register au program mode programming • 165 program 1000 - nlu (number look up) code number programming nlu (number look up) are fixed keys on the keyboard (like traditional department keys) that access specific plus. On the default keyboard, there are 12/16 nlu keys ...
Page 176
166 • program mode programming er-380 / er-380m electronic cash register au program 1100 - cash-in-drawer limit programming you can set a limit for cash in drawer. When cash in drawer exceeds the limit you program here, a warning will display on the screen. You must press clear to remove the warning...
Page 177
Er-380 / er-380m electronic cash register au program mode programming • 167 program 1200 - check change limit programming use this program to set the maximum amount of cash that can be returned when a check is tendered for an amount greater than the amount of the sale. For example, if the check chan...
Page 178
168 • program mode programming er-380 / er-380m electronic cash register au program 1300 - date and time programming use this program to set the clock and calendar on your er-380 / er-380m. The date changes automatically. After initial setting, time changing will probably be required only for beginn...
Page 179
Er-380 / er-380m electronic cash register au program mode programming • 169 program 1400 - scale tare weight programming a tare is the amount of weight representing the container, or package when items are sold by weight. You can pre-program five tare weights, representing the weight of different co...
Page 180
170 • program mode programming er-380 / er-380m electronic cash register au program 1600 - machine number programming the machine number is printed on the register receipt. Program a machine number so that any receipt can be identified with the store or register where the transaction took place. Pro...
Page 181: Program Scans
Er-380 / er-380m electronic cash register au program mode programming • 171 program scans since much time and energy has been invested in the planning and programming of your er-380 / er-380m, it is advisable to print a hard copy of the final program for future reference. This copy should be kept in...
Page 182
172 • program mode programming er-380 / er-380m electronic cash register au others program scan refer to the chart below and enter a digit to represent the segment of the program you wish to print; press the x/time key. To see additional scan, repeat this operation. X x/t ime x program x program 0 g...
Page 183: Sample Reports
Er-380 / er-380m electronic cash register au sample reports • 173 sample reports financial date 15/01/2003 wed time 13:32 x 1 report 00001 -------------------------------- financial +plu ttl 179.56 $288.60 -plu ttl 10 -20.00 adjst ttl 189.56 $268.60 -------------------------------- nontax $30.47 gst...
Page 184
174 • sample reports er-380 / er-380m electronic cash register au continued from previous page drthru ttl 1 $3.04 item disc. 3 -0.48 sale disc. 2 -5.22 sale surch. 3 $3.23 % 4 0 $0.00 % 5 0 $0.00 net sale 26 $281.18 credit gst 4 -1.11 credit tax2 1 -0.23 credit tax3 2 -0.89 credit tax4 1 -0.39 fd/s ...
Page 185
Er-380 / er-380m electronic cash register au sample reports • 175 continued from previous page r/a 3 0 $0.00 p/o 1 1 -140.00 p/o 2 0 $0.00 p/o 3 0 $0.00 hash ttl 0 $0.00 nosale 4 non add # 547 cash-in-d 14 $269.99 check-in-d 3 -108.45 fd/s-in-d 2 $21.00 chg1-in-d 0 $0.00 chg2-in-d 1 $8.43 chg3-in-d ...
Page 186
176 • sample reports er-380 / er-380m electronic cash register au continued from previous page chg6 sales 2 $13.09 chg7 sales 0 $0.00 chg8 sales 1 $3.04 foreign 1 0.00 foreign 2 0.00 foreign 3 0.00 foreign 4 0.00 drwr ttl $216.69 promo 1 $1.50 waste 8 $12.50 tips 0 $0.00 train ttl 5 $62.59 bal forwa...
Page 187: Time
Er-380 / er-380m electronic cash register au sample reports • 177 time date 15/01/2003 wed time 15:48 x 1 report 00001 -------------------------------- time 13:00-13:59 cnt 17 sales amt $183.85 sales rate 65.39% 14:00-14:59 cnt 9 sales amt $97.33 sales rate 34.61% ¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾ ¾ t...
Page 188: Plu
178 • sample reports er-380 / er-380m electronic cash register au plu date 15/01/2003 wed time 15:33 x 1 report 00001 -------------------------------- all plu hamburger cnt 28 $42.00 sales rate 15.64% dbl burger cnt 40 $99.75 sales rate 37.14% coke cnt 26 $38.85 sales rate 14.46% sprite cnt 18 $13.4...
Page 189: Clerk
Er-380 / er-380m electronic cash register au sample reports • 179 clerk note: media totals can be printed for each clerk, if selected in system option programming. Date 15/01/2003 wed time 15:36 x 1 report 00001 -------------------------------- all clerk ethan net sale 10 $155.23 drwr ttl $109.81 --...
Page 190: Individual Clerk
180 • sample reports er-380 / er-380m electronic cash register au individual clerk date 15/01/2003 wed time 15:36 x 1 report 00001 -------------------------------- individual clerk ethan net sale 10 $155.23 drwr ttl $109.81 -------------------------------- ethan 000218 00000 clerk name number of tra...
Page 191: Groups
Er-380 / er-380m electronic cash register au sample reports • 181 groups date 15/01/2003 wed time 15:34 x 1 report 00001 -------------------------------- group group : 1 food cnt 68 sales amt $141.75 group : 2 drink cnt 44 sales amt $52.27 group : 3 rest. Cnt 112 sales amt $194.02 group : 5 store cn...
Page 192: Stock
182 • sample reports er-380 / er-380m electronic cash register au stock date 15/01/2003 wed time 15:47 x 1 report 00001 -------------------------------- all plu stock hamburger cnt 26 dbl burger cnt 15 roast cnt 25.96 unleaded cnt 1488.47 plu33 cnt 161.25 ethan 000228 00000 plu number or plu descrip...
Page 193: Open Check
Er-380 / er-380m electronic cash register au sample reports • 183 open check date 15/01/2003 wed time 15:59 x 1 report 00001 -------------------------------- open check check : 3 $24.07 table : 15 molly check : 4 $45.42 table : 8 ethan check : 5 $24.50 table : 2 ethan check : 6 $28.33 table : 6 etha...