- DL manuals
- Sam4s
- Cash Register
- ER-380
- Operation And Program Manual
Sam4s ER-380 Operation And Program Manual
Summary of ER-380
Page 1
Er-380/ er-380m operation and program manual lyt z_w lsl j{y vu pgjhz og yln pz{l y all specifications are subject to change without notice.
Page 2
Attention the product that you have purchased contains a rechargeable ni-mh battery. This battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of the battery into the municipal waste system. Check with your local solid waste officials...
Page 3: Precaution Statements
Precaution statements follow these safety, servicing and esd precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 safety precautions 1. Be sure that all built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstall...
Page 5
1-2 servicing precautions warning: first read the-safety precautions-section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning: an electrolytic capacitor installed with the wrong polarity mig...
Page 7: Contents
Er-380 / er-380m contents • i contents getting started 1 about the er-380 / er-380m ................................................................................................... 1 unpacking............................................................................................................
Page 8
Ii • contents er-380 / er-380m coupon on sale (vendor coupon) ............................................................................39 coupon on item (store coupon) ...............................................................................40 return merchandise registrations..................
Page 9
Er-380 / er-380m contents • iii function key codes ..................................................................................................77 rs-232 communication options.............................................................................................78 er-380m second rs-232c p...
Page 10
Iv • contents er-380 / er-380m tare.......................................................................................................................134 tax exempt........................................................................................................135 tip .......................
Page 11: Getting Started
Er-380 / er-380m getting started • 1 getting started about the er-380 / er-380m the er-380 / er-380m is offered in three different versions. • the er-380 / er-380m features a raised 44-position keyboard with 12 nlu keys. A standard capacity of 300 plus and 20 groups allows for easy item management. ...
Page 12: Unpacking
2 • getting started er-380 / er-380m unpacking 1. Unpack and unwrap the cash register. 2. Located in the packing are the following items: • 1 roll of paper and paper spindle, • 2 sets of control keys, • operation and program manual, 3. Remove the cardboard protectors from the cash drawer. 4. Plug th...
Page 13
Er-380 / er-380m getting started • 3 2. Push the blue cap lever and then lift up to open the paper cover. Lyt z_w lsl j{yv upgj hzo gyl npz {ly lyt z_w ls lj{ yv upgj hz og yln pz{ly.
Page 14
4 • getting started er-380 / er-380m 3. Ensure that the paper is being fed from the bottom of the roll. Ly tz _w lsl j{y vup gjhz ogy ln pz{l y 4. Put the leading edge of the paper over the printer 5. Close the paper cover slowly until it locks firmly lyt z_w lsl j{ yv upgj hz ogy ln pz{l y.
Page 15
Er-380 / er-380m getting started • 5 6. Passing the leading edge of the paper through the cutter slot. Tear off the excess paper. Replace the printer cover. Lyt z_w lsl j{ yv upgj hzog yln pz{l y ※ if you wish to use the printer to print a sales journal or electronic journal, insert the paper into t...
Page 16: Basic Features and Functions
6 • getting started er-380 / er-380m basic features and functions standard hardware • display => lcd model: adjustable 2 line, 20 character liquid crystal display and ten position rear displays with a rear pop up display standard. => vfd model : ten position front and rear displays with a rear pop u...
Page 17
Er-380 / er-380m getting started • 7 front display vfd model the er-380 comes with a ten position front display. Annotations on the display window include: • rpt, where a counter appears when the same item is multiplied or repeated. • the amount area shows the amount, i.E. Price, subtotal or total. ...
Page 18
8 • getting started er-380 / er-380m negative entry rcpt off void shift clerk rpt amount subtotal amount rpt rcpt off clerk void shift numbered error conditions amount rpt rcpt off clerk void shift.
Page 19: ** Warning **
Er-380 / er-380m getting started • 9 lcd model the er-380m comes with a liquid crystal screen, allowing you to view up to 2 lines of information with up to 20 characters per line. The display is backlit and adjustable to provide excellent visibility, regardless of lighting conditions. When the contr...
Page 20
10 • getting started er-380 / er-380m rear display the rear display is a 10 digit florescent display that allows your customer to monitor the transaction and view the sale total. The rear display can be lifted and turned for easy customer viewing. Rear display information item count the number of ti...
Page 21
Er-380 / er-380m getting started • 11 error code table e0 sequence error e1 plu no data e2 clerk error e3 amount count over e4 lan tran e5 communication error e6 time and date e7 limit over e8 inactive e9 xmode only e10 nonadd e11 addcheck error e12 condiment error e13 req. Eat in e14 req. Stock e15...
Page 22
12 • getting started er-380 / er-380m e34 invalid function e35 req. Table e36 req. Pbal e37 req.Check # e38 only one table e39 req. Valid per receipt printer paper end pco printer cover open pfp system error (if this problem occurs, call the service engineer.) e43 memory allocation error e44 electro...
Page 23
Er-380 / er-380m getting started • 13 control lock the control lock has 7 positions, accessed with 5 keys. Each ecr is shipped with two full sets of keys. Void p z x reg off s void use to void (correct) items outside of a sale. Off the register is inoperable. Reg use for normal registrations. X use ...
Page 24
14 • getting started er-380 / er-380m keyboards the er-380 / er-380m keyboard includes 44 key positions with the default legends and key assignments as shown below. The keyboard legend sheet can be replaced by lifting the protective plastic cover. Programmable key locations are shown with a bold bor...
Page 25: Memory Clear
Er-380 / er-380m getting started • 15 memory clear caution: the procedures described in this area are security sensitive. Clearing all or parts of the er-380/er-380m memory may cause damage or loss to the program. Do not share this information with unauthorized users and distribute the special servi...
Page 26: Initial Clear
16 • getting started er-380 / er-380m initial clear caution: do not share this information with unauthorized users. Distribute the p mode key only to those you may want to perform this function. The initial clear function allows you to exit any register activity and return to a beginning or cleared ...
Page 27: Operating Instructions
Er-380 / er-380m operating instructions • 17 operating instructions function key descriptions keys are listed in alphabetical order. Some of the keys described below are not included on the default keyboard. See “function key assignment programming to add or change programmable keys. Keyboard legend...
Page 28
18 • operating instructions er-380 / er-380m allowed by entering an amount before pressing the check key. The cash drawer will open only if the amount tendered is equal to or greater than the total amount of the sale. Change issued will be subtracted from the cash-in-drawer total. Check cashing use ...
Page 29
Er-380 / er-380m operating instructions • 19 food stamp eligible can be made food stamp eligible. F/s sub displays the amount of the sale that is food stamp eligible. F/s tend use to tender food stamps for eligible sales. Guest # use to enter the count of guests served as part of a guest check. Macr...
Page 30
20 • operating instructions er-380 / er-380m transactions. Sbtl displays subtotal of sale including tax. Must be pressed prior to a sale discount or sale surcharge. Table # tracks the current balance for a guest check or table. Tare tares are container weights. If you are using the scale function, y...
Page 31: Clerk Sign-On/sign-Off
Er-380 / er-380m operating instructions • 21 clerk sign-on/sign-off see "system option programming” to review your clerk options: • system option #2 allows you to select direct or code entry sign on and/or stay- down or pop-up operation. Depending on how your machine has been programmed, sign-on wil...
Page 32: Receipt On and Off
22 • operating instructions er-380 / er-380m receipt on and off 1. Turn the control lock to the x position. 2. To turn the receipt off, enter 9 9, press the sbtl key. Enter 1, press cash. 1 sbtl 9 9 cash 3. To turn the receipt on, enter 9 9, press the sbtl key. Enter 0, press cash. 0 sbtl 9 9 cash.
Page 33: Item Registrations
Er-380 / er-380m operating instructions • 23 item registrations all registrations on er-380 / er-380m are made into open or preset plus. • in place of traditional plu keys, some plus are located directly on the keyboard. • when more items or categories are needed than the number of plus available on...
Page 34
24 • operating instructions er-380 / er-380m open keyboard plu entry 1. Enter an amount on the numberpad. Do not use the decimal key. For example, for $2.99, enter: 2 9 9 2. Press a plu key. For example, press plu 1: 1 thank-you call again date 01/15/2003 wed time 08:33 plu1 t1 $2.99 tax1 $0.18 tota...
Page 35
Er-380 / er-380m operating instructions • 25 keyboard plu repeat entry open or preset price plus can be repeated as many times as necessary by pressing the same plu again. The number of times the item is repeated is shown on the display. 1. Enter an amount on the numberpad. Do not use the decimal ke...
Page 36
26 • operating instructions er-380 / er-380m keyboard plu multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset plus. 1. Enter the quantity of items ...
Page 37
Er-380 / er-380m operating instructions • 27 keyboard plu multiplication with decimal point if you are selling items by weight, or if you are selling yard goods, you can multiply a fraction of a unit. 1. Enter the amount with the decimal point, and then press the x/time key. For example, for 3.75 po...
Page 38
28 • operating instructions er-380 / er-380m split pricing (keyboard plu) when items are priced in groups, i.E. 3 for $1.00, you can enter the quantity purchased and let the register calculate the correct price. 1. Enter the quantity purchased, and then press the x/time key. For example, enter: 2 x/...
Page 39
Er-380 / er-380m operating instructions • 29 single item keyboard plu immediately after registration single item plus automatically total as a cash sale. Use single item plus for speedy one item sales. For example if you are selling admission tickets, and all ticket sales are one item sales, you can...
Page 40
30 • operating instructions er-380 / er-380m open code entry plu if the preset status of a plu is set to n (no), the plu will operate as an open plu. See "plu programming" in the "program mode programming" chapter to program plu descriptors and options. 1. Enter the plu number; press the plu key. Fo...
Page 41
Er-380 / er-380m operating instructions • 31 code entry plu multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset plus. 1. Enter the quantity of item...
Page 42
32 • operating instructions er-380 / er-380m code entry plu multiplication with decimal point if you are selling items by weight, or if you are selling yard goods, you can multiply a fraction of a unit. 1. Enter the quantity with the decimal point, and then press the x/time key. For example, for 3.7...
Page 43
Er-380 / er-380m operating instructions • 33 modifier key pressing a modifier key alters the next plu registered, either by changing the code number of the plu so that a different item is registered, or by just adding the modifier descriptor and registering the same plu. See "modifier 1-5" in the "p...
Page 44
34 • operating instructions er-380 / er-380m price level key if you choose to use the price level feature, you must allocate memory for each level. See "memory allocation" in the "service mode programming" chapter. Note that the default program selects one price level. You must also place price leve...
Page 45
Er-380 / er-380m operating instructions • 35 promo the promo key allows you to account for promotional items, as in "buy two, get one free". Pressing this key will remove an item's cost from the sale, and the promo item will not be added to the plu sales total, but it is added to the item sales coun...
Page 46
36 • operating instructions er-380 / er-380m waste the waste key allows control of inventory by accounting for items that must be removed from stock due to spoilage, breakage or mistakes. Press the waste key before entering wasted items, and then press the waste key again to finalize. The waste key ...
Page 47: Percent Key Operations
Er-380 / er-380m operating instructions • 37 percent key operations a total of five % functions are available. %1 and %2 are located on the default keyboard. Your keyboard may be different. More or less % keys may be located on the keyboard, or they may be located on one of the function look up menu...
Page 48
38 • operating instructions er-380 / er-380m enter a percent discount on an item you can also operate the percentage functions by entering the percentage of the discount or surcharge. You can enter a fractional percentage up two 3 digits beyond the decimal (i.E. 99.999%) if necessary. 1. Register th...
Page 49
Er-380 / er-380m operating instructions • 39 coupon on sale (vendor coupon) when programmed as "amount", "sale", "open" and "negative", a % key will perform a coupon against a sale (or vendor coupon.) also, depending upon programming: • you may be allowed to enter only one coupon in a sale, after th...
Page 50
40 • operating instructions er-380 / er-380m coupon on item (store coupon) when programmed as "amount", "item", "open" and "negative", a % key will perform a coupon against an item (or store coupon.) in this case, you must press the plu (or enter the plu number) of the plu you wish the coupon to be ...
Page 51
Er-380 / er-380m operating instructions • 41 return merchandise registrations if you wish to return or refund an item press return, then re-enter any item. You can return merchandise as part of a sale, or you can return merchandise as a separate transaction and return cash to the customer. 1. Press ...
Page 52: Voids and Corrections
42 • operating instructions er-380 / er-380m voids and corrections error correction (void last item) this function corrects the last item entered. 1. Register the item you wish to sell. 2. Press the error corr key: error corr thank-you call again date 01/15/2003 wed time 08:33 plu1 t1 $2 29 plu2 $1....
Page 53
Er-380 / er-380m operating instructions • 43 cancel the cancel key allows you to stop any transaction. Anything registered within the transaction before the cancel key is pressed is automatically corrected. The cancel key can be inactivated through programming, see "function key programming" in the ...
Page 54: No Sale Operations
44 • operating instructions er-380 / er-380m no sale operations open drawer the #/no sale key will open the cash drawer when you have not already started a transaction. The no sale function can be disabled or placed under manager control through programming, see "function key programming" in the "pr...
Page 55
Er-380 / er-380m operating instructions • 45 received on account operations you can use one of the received on accountfunctions (ra1-ra3) to accept cash or checks into the cash drawer when you are not actually selling merchandise. For example, use received on accountto accept payments for previously...
Page 56: Paid Out Operations
46 • operating instructions er-380 / er-380m paid out operations you can use the paid out function (po1-po3) to track cash or checks paid out or to record loans from the cash drawer. 1. Press one of the paid out keys (po1-po3) po1 2. Enter the amount of cash paid out, press cash. Cash 0 0 0 1 3. Ent...
Page 57: Subtotaling A Sale
Er-380 / er-380m operating instructions • 47 subtotaling a sale 1. Register the items you wish to sell. 2. Press sbtl. The subtotal will display with the message "sub" indicated on the rear display. Sbtl the subtotal can be printed if the system option is set. See "print option programming" in the "...
Page 58: Totaling and Tendering
48 • operating instructions er-380 / er-380m totaling and tendering there are ten tender functions available to categorize sales. Cash and check are individual keys on the keyboard totaling a cash sale 1. Register the items you wish to sell. 2. To total a cash sale, press cash: cash 3. The display w...
Page 59
Er-380 / er-380m operating instructions • 49 tendering a cash sale 1. Register the items you wish to sell. 2. Enter the amount tendered by the customer. For example, for $20.00 enter: 0 0 0 2 3. Press cash: cash 4. The display will indicate the total amount of the cash tendered and the change due, i...
Page 60
50 • operating instructions er-380 / er-380m totaling a charge sale use the charge keys to track charge or credit card sales. See "function key programming" in the "program mode programming" chapter to change the descriptors for the charge tender functions. For example, you can use charge 1 to track...
Page 61
Er-380 / er-380m operating instructions • 51 tendering a charge sale tendering a charge sale may or may not be allowed. See "function key programming" in the "program mode programming" chapter to set tendering options for the charge keys, i.E. Whether to allow over tendering or to enforce tendering....
Page 62
52 • operating instructions er-380 / er-380m check cashing check cashing means exchanging cash for a check. If you wish to cash checks, you must place a chkcash key on the keyboard. See "function key assignment" in the "program mode programming" chapter. 1. Enter the amount of the check tendered by ...
Page 63
Er-380 / er-380m operating instructions • 53 split tender split tendering is paying for one transaction by more than one payment method. For example, a $20.00 sale could be split so $10.00 is paid in cash, and the remaining $10.00 is paid by a check. If necessary, you can make several different paym...
Page 64
54 • operating instructions er-380 / er-380m post tender post tendering means computing change after the sale has been totaled and the drawer is open. This feature is useful when a customer changes the amount of the tender or when a "quick change artist" confuses a clerk. Normally, this function is ...
Page 65
Er-380 / er-380m operating instructions • 55 currency conversion if you normally accept currency from neighboring nations, you can program to convert the subtotal of a sale to the equivalent cost in the foreign currency. You can set up four separate conversion functions for different foreign currenc...
Page 66
56 • operating instructions er-380 / er-380m table management and clerk interrupt operations overview the er-380 / er-380m can employ a manual previous balance, hard check, or soft check system. (you must select hard or soft check posting in memory allocation programming - the default selection is s...
Page 67
Er-380 / er-380m operating instructions • 57 soft check opening a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. If required, enter the table number and press the table key: table 3 3. If req...
Page 68
58 • operating instructions er-380 / er-380m adding to a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: table 3 2. Register the next items you wish to sell. 3. To total the post...
Page 69
Er-380 / er-380m operating instructions • 59 paying a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: table 3 2. If necessary, add additional items. If you wish to add a tip, pre...
Page 70
60 • operating instructions er-380 / er-380m hard check opening a hard check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. If required, enter the table number and press the table key: table 3 3. If req...
Page 71
Er-380 / er-380m operating instructions • 61 adding to a hard check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: table 3 2. Register the next items you wish to sell. 3. To total the post...
Page 72
62 • operating instructions er-380 / er-380m paying a hard check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: table 3 2. If necessary, add additional items. If you wish to add a tip, pre...
Page 73
Er-380 / er-380m operating instructions • 63 direct scale entry place a product on the scale and access the scale function to display the weight on the cash register. Then make the appropriate entry; the plu must have "scaleable" status. 1. Place an item on the scale. 2. Press the scale key. Scale 3...
Page 74
64 • operating instructions er-380 / er-380m automatic scale entry place a product on the scale and make the appropriate plu entry. The plu must be set with "auto scale status". 1. Place an item on the scale. 2. Press a plu key, if the item is a preset item, or enter the price per pound on the numbe...
Page 75
Er-380 / er-380m operating instructions • 65 manual tare weight entry 1. Place an item on the scale. 2. Enter the manual tare number, 5. Press the tare key: 5 tare 3. Enter the weight of the tare, for example, enter .01, press the tare key: 1 tare . 0 4. Press the scale key. Scale 5. Note that the w...
Page 76
66 • operating instructions er-380 / er-380m manual weight entry operators can make manual weight entries if the item has been programmed to accept them. You must use the decimal key to enter fractional manual weights. 1. Place an item on the scale. 2. Enter the weight using the decimal key for frac...
Page 77: X Mode
Er-380 / er-380m x mode • 67 x mode introduction all management functions take place with the control lock in the x position. In this way only those with the correct key will have access to these functions. Some register operations may be programmed to require the control lock in the x position in o...
Page 78: X Reports
68 • x mode er-380 / er-380m x reports system reports are divided into two basic categories: • x reports, which read totals without resetting • z reports, which read totals and reset them to zero most reports are available in both categories. Some reports, such as the cash-in-drawer report and the f...
Page 79
Er-380 / er-380m x mode • 69 report table report type report number report mode control lock position key sequence 1 x x 1 – sbtl z z 1 – sbtl x2 x 201 – sbtl financial z2 z 201 – sbtl 2 x x 2 – sbtl z z 2 – sbtl x2 x 202 – sbtl time z2 z 202 – sbtl 3 x x 3 – sbtl z z 3 – sbtl x2 x 203 – sbtl all pl...
Page 80
70 • x mode er-380 / er-380m print ej % 304 x x 304 -sbtl print ej ra/po 305 x x 305 -sbtl print ej return 306 x x 306 -sbtl print ej ec/void 307 x x 307 -sbtl print ej no sale 308 x x 308 -sbtl print ej cancel 309 x x 309 –sbtl print ej by clerk 401 – 15 x x/z 401-415(depends on max clerk)-sbtl ej ...
Page 81: Cash Declaration
Er-380 / er-380m x mode • 71 cash declaration if compulsory cash declaration is required, you must declare the count of the cash drawer prior to taking x or z financial and clerk reports. You can enter the cash drawer total in one step, or to facilitate the counting of the cash drawer, you can enter...
Page 82: Service Mode Programming
72 • service mode programming er-380 / er-380m service mode programming overview the following procedures are done from the service mode menu: • clear all totals • clear grand total • clear plu file • eprom information • memory allocation • assignment of functions to keyboard locations • rs232c port...
Page 83: Memory Allocation Scan
Er-380 / er-380m service mode programming • 73 memory allocation scan 1.Turn the control lock to the s position to scan the allocated memory. 2. Enter 60, press the sbtl key. 0 sbtl 6 3.Press cash key cash pc online mode in er-380 / er-380m, there are no special commands to enter pc online mode. Whe...
Page 84: Memory Allocation
74 • service mode programming er-380 / er-380m memory allocation 1. Turn the control lock to the s position. 2. To allocate memory, enter 60, and then press the sbtl key. 0 sbtl 6 3. Refer to the chart below. Enter the index number and press the x/time key. X x/time x memory item 1 plu 2 clerk 3 gro...
Page 85: Clear Total
Er-380 / er-380m service mode programming • 75 clear total 1.Turn the control lock to the s position. 2.To reset total, enter 20, and then press the sbtl key. 0 sbtl 2 clear grand total 1.Turn the control lock to the s position. 2. To reset grand total, enter 30, and then press the sbtl key. 0 sbtl ...
Page 86
76 • service mode programming er-380 / er-380m function key assignment programming function keys may be relocated, inactivated or changed with this program. For example, you may wish to place functions, such as previous balance and service that are not placed on the default keyboard. Or perhaps, you...
Page 87
Er-380 / er-380m service mode programming • 77 function key codes code function code function code function code function 1 nlu 1 37 charge 1 63 level 1 89 rec on acct 2 12 nlu 12 38 charge 2 64 level 2 90 rec on acct 3 13 reserved 39 charge 3 65 macro 1 91 sbtl 14 reserved 40 charge 4 66 macro 2 92...
Page 88: Rs-232 Communication Options
78 • service mode programming er-380 / er-380m rs-232 communication options you must define the device that is attached to the rs-232c communications port, and the options for the device. 1. Turn the control lock to the s position. 2. Enter 8 0 and press the sbtl key. 3. Refer to the chart rs-232c o...
Page 89
Er-380 / er-380m service mode programming • 79 n1 option n2 value 8 eft 9 pole 6 initial feeding line kp 0 - 20 7 end feeding line kp 0 - 20 8 initial feeding line slip 0 - 20 9 print line on guest check 0 - 50 0 nci 10 scale type 1 cas 0 none 1 samsung srp-100 2 srp-250 3 srp-300 4 srp-350 5 citize...
Page 90
80 • service mode programming er-380 / er-380m er-380m second rs-232c port programming the er-380m includes a standard second rs-232c port. The second port is set in the same manner as the first, using program 81: 1. Turn the control lock to the s position. 2. Enter 8 1 and press the sbtl key. 3. Re...
Page 91: Program Mode Programming
Er-380 / er-380m program mode programming • 81 program mode programming default programming • all keyboard plus are nontaxable and open, without entry limits by default status programming of "00000000". • all system options are set to 0 in default programming, unless otherwise noted. Change only the...
Page 92
82 • program mode programming er-380 / er-380m descriptor code method char Ç ü é â ä à å ç ê ë code 001 002 003 004 005 006 007 008 009 010 char è ï î ì Ä Å É æ Æ ô code 011 012 013 014 015 016 017 018 019 020 char ö ò û ù ÿ Ö Ü ¢ £ ¥ code 021 022 023 024 0250 026 027 028 029 030 char € space ! " # ...
Page 93: Tax Programming
Er-380 / er-380m program mode programming • 83 tax programming the er-380 / er-380m has the capability to support four separate taxes. Taxes can be calculated as either a straight percentage rate of between .001% and 99.999%, or a 60 break point tax table. Each tax may be either an add-on tax (added...
Page 94
84 • program mode programming er-380 / er-380m 4. Enter 0 here for all taxes, unless if you are programming tax 4 as a canadian gst. If tax 4 is a canadian gst, enter the sum of the options below: option value = sum gst (tax 4) is taxable by rate 1? Yes = 1 no = 0 gst (tax 4) is taxable by rate 2? Y...
Page 95: Plu
Er-380 / er-380m program mode programming • 85 plu programming all plus, whether they are registered by pressing a plu key on the keyboard, or by entering the plu number and pressing the plu key, have the same programming options. These options are set through separate programs: • program 100 – plu ...
Page 96
86 • program mode programming er-380 / er-380m program 100 - plu status programming 1. Turn the control lock to the p position. 2. To begin the program, enter 1 0 0, press the sbtl key. 0 sbtl 0 1 3. Select the plu or plus you wish to program in one of the following ways: • press a plu key on the ke...
Page 97
Er-380 / er-380m program mode programming • 87 plu status chart address program option value = sum plu is preset? Yes = 0 no = 1 plu is override preset ? Yes = 0 no = 2 n1 plu is taxable by rate 1? Yes = 4 no = 0 plu is taxable by rate 2? Yes = 1 no = 0 plu is taxable by rate 3? Yes = 2 no = 0 n2 pl...
Page 98
88 • program mode programming er-380 / er-380m address program option value = sum plu counter is not reset when a plu z report is done? Yes = 1 no = 0 n9 plu is preset override in mgr control? Yes = 2 no = 0
Page 99
Er-380 / er-380m program mode programming • 89 program 110 - plu auto tare programming 1. Turn the control lock to the p position. 2. To begin the program, enter 1 1 0, press the sbtl key 0 sbtl 1 1 3. Select the plu or plus you wish to program in one of the following ways: press on the keyboard, or...
Page 100
90 • program mode programming er-380 / er-380m program 150 - plu group assignment each plu may report to any three of 20 groups. Group totals appear on reports, so that you can track sales of different types of items. A group can also be used to designate items that are to print on an optional kitch...
Page 101
Er-380 / er-380m program mode programming • 91 program 200 - plu price/halo programming if a plu is open, set the halo (high amount lock out) here. If a plu is preset set the preset price here. If a plu is set with gallonage status, enter the price per gallon here. (enter price per gallon in tenths ...
Page 102
92 • program mode programming er-380 / er-380m program 250 - plu stock amount programming with this program, you can you can add stock to the plu sales counters for plus you have designated as stock keeping plus. See “program 100 – plu status programming”. The stock number set here can be the amount...
Page 103
Er-380 / er-380m program mode programming • 93 program 300 - plu description programming program descriptors by entering three digit alpha character codes. 1. Turn the control lock to the p position 2. To begin the program, enter 3 0 0, press the sbtl key. 0 sbtl 0 3 3. Select the plu you wish to pr...
Page 104
94 • program mode programming er-380 / er-380m program 350 - plu link programming plu link programming allows you to link a plu to another plu, so that registration of the first plu will automatically trigger registration of the linked plu. For example, you may wish to link a bottle deposit with the...
Page 105
Er-380 / er-380m program mode programming • 95 program 400 – plu delete programming note: to delete a plu, all totals for the plu must be cleared from z reports (including stock and plu reports.) 1. Turn the control lock to the p position. 2. To begin the program, enter 4 0 0, press the sbtl key. 0 ...
Page 106
96 • program mode programming er-380 / er-380m program 450 - plu mix & match programming 1. Turn the control lock to the p position. 2. To begin the program, enter 4 5 0, press the sbtl key. 0 sbtl 5 4 3. Select the plu you wish to program in one of the following ways: • press a plu key on the keybo...
Page 107: System Option Programming
Er-380 / er-380m program mode programming • 97 system option programming refer to the “system option table” to review the system options. Read each option carefully to determine if you wish to make any changes. Note: because after clearing memory all options settings are automatically set to 0, and ...
Page 108
98 • program mode programming er-380 / er-380m system option table address system option value = sum beeper is active? Yes = 0 no = 1 1 % is not to affect net sale? Yes = 2 no = 0 direct entry = 0 2 clerk sign on method is: code entry = 1 pop-up = 1 3 clerks are: stay down = 0 drawer needs to be shu...
Page 109
Er-380 / er-380m program mode programming • 99 address system option value = sum round up at 0.005 = 0(default) always round up = 1 12 percentage and tax calculations will: always round down = 2 round up at 0.005 = 0(default) always round up = 1 13 split price calculations will: always round down = ...
Page 110
100 • program mode programming er-380 / er-380m address system option value = sum allow swedish round on subtotal? Yes = 4 no = 0 allow rounding on cash? Yes = 1 no = 0 22 allow z stock report? Yes = 0 no = 2 enter = 1 23 training mode exit = 0 enable electronic journal? Yes = 1 no = 0 prompt operat...
Page 111: Print Option Programming
Er-380 / er-380m program mode programming • 101 print option programming refer to the “print option table” to review the print options. Read each option carefully to determine if you wish to make any changes. Note: because after clearing memory all options settings are automatically set to 0, and be...
Page 112
102 • program mode programming er-380 / er-380m print option table address print option value = sum print media total on clerk report? Yes = 1 no = 0 1 print tax symbol? Yes = 0 no = 2 void/return totals will print on the financial report? Yes = 0 no = 1 2 audaction total will print on the financial...
Page 113
Er-380 / er-380m program mode programming • 103 address print option value = sum print gross total on the x financial report? Yes = 0 no = 1 10 print gross total on the z financial report? Yes = 0 no = 2 print the subtotal without tax on the receipt? Yes = 1 no = 0 combined = 2 11 tax amount to prin...
Page 114
104 • program mode programming er-380 / er-380m address print option value = sum print preamble message on the guest check? Yes = 1 no = 0 22 print postamble message on the guest check? Yes = 2 no = 0 print average items per customer on the financial report? Yes = 0 no = 1 23 print average sales per...
Page 115
Er-380 / er-380m program mode programming • 105 note 1: print option# 8 - users outside of the usa can designate a different currency symbol. To select a different symbol enter three digit alpha character codes. Note 2: print option# 14,15,16,17 - if you are using the currency conversion feature, yo...
Page 116: Function Key Programming
106 • program mode programming er-380 / er-380m function key programming three programs are used to program function keys: • program 70 - is used to set each keys individual options • program 80 - is used to program a 18 character alpha numeric descriptor • program 90 - is used to set a high amount ...
Page 117
Er-380 / er-380m program mode programming • 107 program 70 - function key options use program 70 to set options for function keys. Because of the differences inherent in function keys, individual options will be different. See the specific instructions for each key in this chapter to find the option...
Page 118
108 • program mode programming er-380 / er-380m program 80 - function key descriptor program descriptors by entering three digit alpha character codes. 1. Turn the control lock to the p position. 2. To begin the program, enter 8 0, press the sbtl key. 0 sbtl 8 3. Enter up to 18 three-character codes...
Page 119
Er-380 / er-380m program mode programming • 109 program 90 - function key halo use program 90 to program a high amount lock out (halo) for a function key. Only specific keys require this program. For example, you can set a halo for the cash, check or charge keys. Refer to the specific function key p...
Page 120
110 • program mode programming er-380 / er-380m add check options - program 70 add cehck cash repeat for another function key n1 sbtl 0 7 n2 n3 address option value = sum key is inactive? Yes = 1 no = 0 compulsory before tendering? Yes = 2 no = 0 n1 advance the consecutive # when this function is us...
Page 121
Er-380 / er-380m program mode programming • 111 cancel options - program 70 cancel cash repeat for another function key n1 sbtl 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes = 4 no = 0 des...
Page 122
112 • program mode programming er-380 / er-380m cash options - program 70 cash cash n1 sbtl 0 7 n2 n3 repeat for another function key address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock position only? Yes = 2 no = 0 n1 dis...
Page 123
Er-380 / er-380m program mode programming • 113 charge1-8 charge cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 n5 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock position only? Yes = 2 no = 0 n1 disable und...
Page 124
114 • program mode programming er-380 / er-380m check options - program 70 check cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock position only? Yes = 2 no = 0 n...
Page 125
Er-380 / er-380m program mode programming • 115 check cashing options - program 70 check cash cash n1 sbtl 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes = 4...
Page 126
116 • program mode programming er-380 / er-380m check endorsement options - program 70 check endorse cash repeat for another function key n1 sbtl 0 7 n2 address option value = sum key is inactive? Yes = 1 no = 0 print the amount of the check and endorsement message? Yes = 2 no = 0 n1 print date? Yes...
Page 127
Er-380 / er-380m program mode programming • 117 check # options - program 70 check# cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 address option value = sum key is inactive? Yes = 1 no = 0 required at start of sale? Yes = 2 no = 0 n1 opening clerk has exclusive access? Yes = 4 no = 0 che...
Page 128
118 • program mode programming er-380 / er-380m currency conversion currency conversion rate - program 90 1. Turn the control lock to the p position. 2. To begin the program, enter 9 0, press the sbtl key. 0 sbtl 9 3. Enter the exchange rate of up to 7 digits (do not enter the decimal point), and th...
Page 129
Er-380 / er-380m program mode programming • 119 drive thru / eat in / take out options - program 70 drive thru cash n1 sbtl 0 7 n2 repeat for another function key eat in cash n1 sbtl 0 7 n2 repeat for another function key take out cash n1 sbtl 0 7 n2 repeat for another function key address option va...
Page 130
120 • program mode programming er-380 / er-380m error correct options - program 70 error correct cash repeat for another function key n1 sbtl 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes ...
Page 131
Er-380 / er-380m program mode programming • 121 f/s tend options - program 70 f/s tend cash repeat for another function key n1 sbtl 0 7 n2 n3 address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax 4? Yes = 1 no = 0 the tender i...
Page 132
122 • program mode programming er-380 / er-380m guest options - program 70 guest cash repeat for another function key n1 sbtl 0 7 address option value = sum required when opening a new check? Yes = 1 no = 0 before registering, enter a guest number? Yes = 2 no = 0 n1 print guest # at the kitchen prin...
Page 133
Er-380 / er-380m program mode programming • 123 #/ns options - program 70 #/ns cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 address option value = sum no sale is inactive? Yes = 1 no = 0 no sale active in x control lock position only? Yes = 2 no = 0 n1 no sale inactive after non-add # e...
Page 134
124 • program mode programming er-380 / er-380m descriptor - programs 80 & 81 since two distinct functions, # entry and no sale, reside on the same key, different programs are used to program each descriptor. To program the no sale descriptor: function key cash repeat for another function key sbtl 0...
Page 135
Er-380 / er-380m program mode programming • 125 modifier 1-5 options - program 70 mod cash repeat for another function key n1 sbtl 0 7 n2 n3 address option value = sum key is active in x control lock position only? Yes = 1 no = 0 n1 modify plu#? Yes = 2 no = 0 print modifier descriptor on the guest ...
Page 136
126 • program mode programming er-380 / er-380m payment options - program 70 payment cash repeat for another function key n1 sbtl 0 7 address option value = sum n1 required to close check? Yes = 1 no = 0 descriptor - refer to “program 80 – function key descriptor” pbal options - program 70 previous ...
Page 137
Er-380 / er-380m program mode programming • 127 promo options - program 70 promo cash repeat for another function key n1 sbtl 0 7 n2 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 taxable by tax 1? Yes = 4 no = 0 taxable by...
Page 138
128 • program mode programming er-380 / er-380m paid out1-3 options - program 70 p/o cash n1 sbtl 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only yes = 2 no = 0 n1 validation is compulsory? Yes = 4 no = 0 de...
Page 139
Er-380 / er-380m program mode programming • 129 print check options - program 70 print check cash repeat for another function key n1 sbtl 0 7 n2 address option value = sum n1 enter port number. (zero if the check will print on the receipt printer) er380 er380m 0-1 0-2 automatically service check? Ye...
Page 140
130 • program mode programming er-380 / er-380m recd on acct1-3 options - program 70 r/a cash n1 sbtl 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes = 4 no =...
Page 141
Er-380 / er-380m program mode programming • 131 scale options - program 70 scale cash n1 sbtl 0 7 n2 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 allow manual entry of weight? Yes = 4 no = ...
Page 142
132 • program mode programming er-380 / er-380m service options - program 70 service cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 address option value = sum compulsory non-add number before this key is used? Yes = 1 no = 0 print on receipt? Yes = 0 no = 2 n1 allow negative balance in x ...
Page 143
Er-380 / er-380m program mode programming • 133 subtotal options - program 70 subtotal cash repeat for another function key n1 sbtl 0 7 address option value = sum n1 key is inactive? Yes = 1 no = 0 descriptor - refer to “program 80 – function key descriptor” table options - program 70 table # cash n...
Page 144
134 • program mode programming er-380 / er-380m tare options - program 70 tare cash repeat for another function key n1 sbtl 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 using tare number five to manually enter a tare ...
Page 145
Er-380 / er-380m program mode programming • 135 tax exempt options - program 70 tax exempt cash n1 sbtl 0 7 n2 repeat for another function key address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax 4? Yes = 1 no = 0 compulsory ...
Page 146
136 • program mode programming er-380 / er-380m tip options - program 70 tip cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 address option value = sum percentage = 1 n1 type of tip is: amount = 0 key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0...
Page 147
Er-380 / er-380m program mode programming • 137 validate options - program 70 valid cash repeat for another function key n1 sbtl 0 7 n2 address option value = sum n1 enter port number. Enter zero if validation is not used. Er380 er380m 0-1 0-2 key is inactive? Yes = 1 no = 0 n2 allow multiple valida...
Page 148
138 • program mode programming er-380 / er-380m void options - program 70 void cash n1 sbtl 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes = 4 no = 0 descrip...
Page 149
Er-380 / er-380m program mode programming • 139 waste options - program 70 waste cash n1 sbtl 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Yes = 4 no = 0 descr...
Page 150
140 • program mode programming er-380 / er-380m %1- %5 options - program 70 % cash repeat for another function key n1 sbtl 0 7 n2 n3 n4 n6 n5 address option value = sum amount = 1 apply an: percentage = 0 key is inactive? Yes = 2 no = 0 n1 % key is active in x control lock position only? Yes = 4 no ...
Page 151
Er-380 / er-380m program mode programming • 141 descriptor - refer to “program 80 – function key descriptor” halo - program 90 % cash repeat for another function key sbtl 0 9 enter 5 digit rate or amount (see note below) note: if key is amount, enter 5 digit halo, or 0 for no halo. If key is percent...
Page 152: Clerk Programming
142 • program mode programming er-380 / er-380m clerk programming clerks (which may be used as cashiers), have the following programming options. These options are set through separate programs: • program 800 - secret code programming determines the code that is used for clerk sign on if a code entr...
Page 153
Er-380 / er-380m program mode programming • 143 program 800 - secret code programming 1. Turn the control lock to the p position. 2. To begin the program, enter 8 0 0, press the sbtl key. 0 sbtl 0 8 3. Enter the number of the clerk you wish to program; press the x/time key. X/time 4. Enter a secret ...
Page 154
144 • program mode programming er-380 / er-380m program 801 - drawer assignment & training clerk 1. Turn the control lock to the p position. 2. To begin the program, enter 8 0 1, press the sbtl key. 1 sbtl 0 8 3. Enter the number of the clerk you wish to program; press the x/time key. X/time 4. Ente...
Page 155
Er-380 / er-380m program mode programming • 145 program 810 – clerk description programming program descriptors by entering three digit alpha character codes. 1. Turn the control lock to the p position. 2. To begin the program, enter 8 1 0, press the sbtl key. 0 sbtl 1 8 3. Enter the number of the c...
Page 156: Mix & Match Programming
146 • program mode programming er-380 / er-380m mix & match programming mix & match tables have the following programming options. These options are set through separate programs: • program 600 - trip level programming • program 601 - price programming • program 610 - mix & match description program...
Page 157
Er-380 / er-380m program mode programming • 147 program 600 - trip level programming 1. Turn the control lock to the p position. 2. To begin the program, enter 6 0 0, press the sbtl key. 0 sbtl 0 6 3. Enter the number of the m&m table you wish to program; press the x/time key. X/time 4. Enter a leve...
Page 158
148 • program mode programming er-380 / er-380m program 610 - mix & match description programming program descriptors by entering three digit alpha character codes. 1. Turn the control lock to the p position. 2. To begin the program, enter 6 1 0, press the sbtl key. 0 sbtl 1 6 3. Enter the number of...
Page 159: Group Programming
Er-380 / er-380m program mode programming • 149 group programming 20 group totals are available to accumulate totals of individual plus that are assigned to each group. Each plu can be assigned to one, two or three different groups. • use program 900 to assign a group status, i.E. A group can be set...
Page 160
150 • program mode programming er-380 / er-380m programming group descriptors 1. Turn the control lock to the p position. 2. To begin the program, enter 9 1 0, press the sbtl key. 0 sbtl 1 9 3. Enter the number of the group you wish to program; press the x/time key. X/time 4. If you are programming ...
Page 161: Miscellaneous Programming
Er-380 / er-380m program mode programming • 151 miscellaneous programming macro key sequence programming macros are special function keys that are used to execute a sequence of key depressions. For example, a macro might be used to execute a string of reports or to automatically tender a preset amou...
Page 162
152 • program mode programming er-380 / er-380m logo description programming programming the receipt/check endorsement message a preamble message of up to six lines can be printed at the top of each receipt; a postamble message of up to six lines can be printed at the bottom of each receipt: a endor...
Page 163
Er-380 / er-380m program mode programming • 153 programming the financial report message the financial report selection allows you to reprogram the descriptors that appear with the financial report totals and counters. For example, the first total on the financial report "+plu ttl" represents the to...
Page 164
154 • program mode programming er-380 / er-380m financial report message x message line x message line x message line 1 +plu ttl 29 credit tax4 57 chg7-in-d 2 -plu ttl 30 fd/s credit 58 chg8-in-d 3 adjst ttl 31 return 59 chg1 sales 4 nontax 32 error corr 60 chg2 sales 5 tax1 sales 33 previous vd 61 ...
Page 165
Er-380 / er-380m program mode programming • 155 programming the clerk report message the clerk report selection allows you to reprogram the descriptors that appear with the clerk report totals and counters. For example, the first total on the clerk report "net sales" might be re-labeled to say "gros...
Page 166
156 • program mode programming er-380 / er-380m clerk report message x message line x message line x message line 1 net sale 24 credit tax2 47 chg2 sales 2 nontax 25 credit tax3 48 chg3 sales 3 tax1 sales 26 credit tax4 49 chg4 sales 4 tax2 sales 27 fd/s credit 50 chg5 sales 5 tax3 sales 28 return 5...
Page 167
Er-380 / er-380m program mode programming • 157 programming the macro name up to ten function locations may be designated as macro keys. You may wish to program a name for a macro. For example if a macro executes a series of commands to produce daily reports, you can program the descriptor “daily”, ...
Page 168
158 • program mode programming er-380 / er-380m nlu code number programming nlu are fixed keys on the keyboard (like traditional department keys) that access specific plus. On the default keyboard, there are 12 nlu keys and the plu# assigned to the nlu key is the same, i.E. Nlu key number one is plu...
Page 169
Er-380 / er-380m program mode programming • 159 cash-in-drawer limit programming you can set a limit for cash in drawer. When cash in drawer exceeds the limit you program here, a warning will display on the screen. You must press clear to remove the warning and continue operations. The warning will ...
Page 170
160 • program mode programming er-380 / er-380m check change limit programming use this program to set the maximum amount of cash that can be returned when a check is tendered for an amount greater than the amount of the sale. For example, if the check change limit is $10.00 the maximum amount that ...
Page 171
Er-380 / er-380m program mode programming • 161 date and time programming use this program to set the clock and calendar on your er-380 / er-380m. The date changes automatically. After initial setting, time changing will probably be required only for beginning and ending daylight savings time. Progr...
Page 172
162 • program mode programming er-380 / er-380m scale tare weight programming a tare is the amount of weight representing the container, or package when items are sold by weight. You can pre-program five tare weights, representing the weight of different containers. When you place an item and a cont...
Page 173
Er-380 / er-380m program mode programming • 163 machine number programming the machine number is printed on the register receipt. Program a machine number so that any receipt can be identified with the store or register where the transaction took place. Programming the machine number 1. Turn the con...
Page 174: Program Scans
164 • program mode programming er-380 / er-380m program scans since much time and energy has been invested in the planning and programming of your er-380 / er-380m, it is advisable to print a hard copy of the final program for future reference. This copy should be kept in a safe place. 1. Turn the c...
Page 175
Er-380 / er-380m program mode programming • 165 others program scan x x/time x program x program 0 group 9 financial report message 1 tax 10 clerk report message 2 system option 11 macro name 3 print option 12 drawer limit 4 function keys 13 check change limit 5 clerk 14 time & date 6 preamble messa...
Page 176: Sample Reports
166 • sample reports er-380 / er-380m sample reports financial date 11/10/1999 wed time 13:32 x 1 report 00001 -------------------------------- financial +plu ttl 179.56 $288.60 -plu ttl 10 -20.00 adjst ttl 189.56 $268.60 -------------------------------- nontax $30.47 tax1 sales $153.60 tax2 sales $...
Page 177
Er-380 / er-380m sample reports • 167 continued from previous page sale disc. 2 -5.22 sale surch. 3 $3.23 % 4 0 $0.00 % 5 0 $0.00 net sale 26 $281.18 credit tax1 4 -1.11 credit tax2 1 -0.23 credit tax3 2 -0.89 credit tax4 1 -0.39 fd/s credit 0 $0.23 return 33 -59.73 error corr 2 -4.00 previous vd 1 ...
Page 178
168 • sample reports er-380 / er-380m continued from previous page hash ttl 0 $0.00 nosale 4 non add # 547 cash-in-d 14 $269.99 check-in-d 3 -108.45 fd/s-in-d 2 $21.00 chg1-in-d 0 $0.00 chg2-in-d 1 $8.43 chg3-in-d 1 $8.52 chg4-in-d 2 -1.60 chg5-in-d 1 $2.67 chg6-in-d 2 $13.09 chg7-in-d 0 $0.00 chg8-...
Page 179
Er-380 / er-380m sample reports • 169 continued from previous page drwr ttl $216.69 promo 1 $1.50 waste 8 $12.50 tips 0 $0.00 train ttl 5 $62.59 bal forward 4 $88.13 guests 5 p/bal 4 $0.00 checks paid 2 $18.64 service 4 $88.13 mix&match 0 $0.00 avg item/cust 7.29 avg $/cust $10.81 ******************...
Page 180: Time
170 • sample reports er-380 / er-380m time date 11/10/1999 wed time 15:48 x 1 report 00001 -------------------------------- time 13:00-13:59 cnt 17 sales amt $183.85 sales rate 65.39% 14:00-14:59 cnt 9 sales amt $97.33 sales rate 34.61% ******************************** total cnt 26 total amt $281.18...
Page 181: Plu
Er-380 / er-380m sample reports • 171 plu date 11/10/1999 wed time 15:33 x 1 report 00001 -------------------------------- all plu plu#1 hamburger cnt 28 $42.00 sales rate 15.64% plu#2 dbl burger cnt 40 $99.75 sales rate 37.14% plu#4 coke cnt 26 $38.85 sales rate 14.46% plu#5 sprite cnt 18 $13.42 sa...
Page 182: Clerk
172 • sample reports er-380 / er-380m clerk note: media totals can be printed for each clerk, if selected in system option programming. Date 11/10/1999 wed time 15:36 x 1 report 00001 -------------------------------- all clerk ethan net sale 10 $155.23 drwr ttl $109.81 ------------------------------...
Page 183: Individual Clerk
Er-380 / er-380m sample reports • 173 individual clerk date 11/10/1999 wed time 15:36 x 1 report 00001 -------------------------------- individual clerk ethan net sale 10 $155.23 drwr ttl $109.81 -------------------------------- ethan 000218 00000 clerk name number of transactions net sales for this...
Page 184: Groups
174 • sample reports er-380 / er-380m groups date 11/10/1999 wed time 15:34 x 1 report 00001 -------------------------------- group group : 1 food cnt 68 sales amt $141.75 group : 2 drink cnt 44 sales amt $52.27 group : 3 rest. Cnt 112 sales amt $194.02 group : 5 store cnt 19.16 sales amt $30.47 gro...
Page 185: Stock
Er-380 / er-380m sample reports • 175 stock date 11/10/1999 wed time 15:47 x 1 report 00001 -------------------------------- all plu stock plu#1 hamburger cnt 26 plu#2 dbl burger cnt 15 plu#7 roast cnt 25.96 plu#28 unleaded cnt 1488.47 plu#33 nails cnt 161.25 ethan 000228 00000 plu number plu descri...
Page 186: Open Check
176 • sample reports er-380 / er-380m open check date 11/10/1999 wed time 15:59 x 1 report 00001 -------------------------------- open check check : 3 $24.07 molly check : 4 $45.42 ethan check : 5 $24.50 ethan check : 6 $28.33 ethan ethan 000243 00000 open check number and balance. Clerk responsible...
Page 187: Appendix A
Er-380 / er-380m appendix a • 177 appendix a eeprom version differences er380 v 1.0 1) initial release er380 v 1.1 (same as er380m initial release) 1) added print option 33 printer format 2) added receipt on/off key (code 107) 3) increased transaction buffer to 100 lines er380 v1.2 (er380m v1.1) 1) ...