Servend SV-200 SCI Installation, Use & Care Manual - page 32
Operation
Section 3
3-8
Part Number 020003997
4/12
FLAVOR MAGIC DISPENSING MODES
For Units With This Option
Normal Dispense
With power applied to the control board, it will automatically
start in dispense mode after a five (5) second delay. The LED
display will count down from four (4) to zero (0) and then show
“- - - -” while in dispense mode. Simply pressing the desired
flavor on the touchpad dispenses Flavor Magic.
Flavor Counter
The flavor counter tracks the number of flavor shots
dispensed per flavor. To access Flavor Counter Mode, press
the program button on the control board once for at least
three (3) seconds. The LED display will show “C n t”. In the
count mode the Flavor Magic module will not dispense.
Check the number of dispenses for any flavor by pressing
the corresponding touchpad button. To check another flavor
press the program button once and then the corresponding
flavor button on the touchpad. To return to dispense mode
press the program button until the LED display shows “- - - -”.
CHANGING NUMBER OF ACTIVE FLAVORS
To line up flavors with valves, note that valve outlets number
from left to right 1…2…3…4. Touch pad flavor tab is
numbered as shown below. Connect vinyl tube from outlet 1
and dispense with flavor tab 1, etc..
The current Flavor Magic control board is set up in the 4
flavor default mode. This mode will handle all dispensing
situations whether 3 or 4 flavors are used. Some early
boards were set up as default in the 3 flavor mode. If the
customer desires to add another flavor for a total of 4,
proceed as follows:
1. Power down the circuit board by disconnecting the 24
volt connector in the lower left hand side of the board.
“24VAC” is imprinted on the board next to the pin
connection.
2. Wait a minimum of 10 seconds.
3. Power up the board by connecting the 24 volt connector.
4. IMMEDIATELY (within 5 seconds) press and hold the
“PROG” button down.
5. After a few seconds, the number “4” will appear on the
display.
6. Release the “PROG” button. The board will cycle the
display from “Pro” to “4……3……2……1……0” and
then to “- - - -”.
7. The circuit board is now enabled to dispense the 4th
flavor. The 4th flavor button is the top middle button.
8. A flavor tab for the 4th flavor will have to be added to the
touch pad. To do this, obtain one (1) P/N 5030780 20
flavor decal pad. Remove the P/N 5031579 decal
overlay and add the 4th flavor tab as well as replace any
flavor tabs which came off when removing the decal
overlay.
NOTE: Position of 4th flavor on the touch pad in the
picture and placed tab where indicated.
9. Obtain a new P/N 5031579 decal overlay and place
over the tabs.
If the customer decides to go back to 3 flavors, it will not be
necessary to change the board back to 3 flavors. However, it
can be done by following steps 1 through 6 above. The
number “3” will appear on the display. Then disconnect the
number “4” syrup from the system, remove the 5031579
decal overlay, remove the flavor tab “4” and replace the
5031579 decal overlay.
NOTE: It would be a good idea to have an additional P/N
5030780 in case flavor tabs are damaged in the process.
TIME DELAY AFTER DISPENSE
1. A time delay can be programmed into the control board
which will prevent the system from dispensing another
flavor for a period of from 0 to 10 seconds following a
dispense. The default is 0 seconds.
2. Enter the Time Delay mode by pressing the program
button until “d L A Y” is displayed. To check the current
delay time press any flavor button one time and the
current value will be displayed. To increase the time (+)
by 1.0 second increments press flavor button 1 (far left
button).
3. To decrease the time (-) by 1.0 second increments
press flavor button 3 (far right button). When done move
on to another programming mode or if you are finished
return the control board to the dispense mode by
pressing the program button and holding for 3 seconds
or until the LED displays 0.
1
2
3
4