Installation, use & care manual this manual is updated as new information and models are released. Visit our website for the latest manual. Www.Manitowocfsg.Com leader in ice & beverage dispensers selectable ice beverage/ice dispensers part number 020003997 4/12.
We reserve the right to make product improvements at any time. Specifications and design are subject to change without notice. Safety notices as you work on manitowoc equipment, be sure to pay close attention to the safety notices in this manual. Disregarding the notices may lead to serious injury a...
Part number 020003997 4/12 i table of contents section 1 general information read this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Table of contents (continued) ii part number 020003997 4/12 co 2 supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 routing internal carb tank purge tube . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 drains . . . . . ....
Table of contents (continued) part number 020003997 4/12 iii programming modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 selectable ice non-adjustable agitation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 crushed or cubed default . ...
Table of contents (continued) iv part number 020003997 4/12.
Part number 020003997 4/12 1-1 section 1 general information read this manual manitowoc beverage equipment (mbe) developed this manual as a reference guide for the owner/operator and installer of this equipment. Please read this manual before installation or operation of the machine. A qualified ser...
General information section 1 1-2 part number 020003997 4/12 manual fill lid for dispensers with an ice machine if you are top mounting your dispenser with an ice machine, you will require a lid for the manual fill area at the top, front of the dispenser. If you ordered a dispenser and an ice machin...
Part number 020003997 4/12 2-1 section 2 installation instructions general these instructions are provided to assist the qualified installer. Contact your manitowoc beverage equipment service agent or call manitowoc beverage equipment for information regarding start-up services. Dimensions selectabl...
Installation instructions section 2 2-2 part number 020003997 4/12 footprint selectable ice maximum minimum a b c d sv-200/250sci 26.00" (66.0 cm) 17.81" (45.2 cm) 4.00" (20.30 cm) 24.00" (61.00 cm) ! Caution cutting the countertop may decrease its strength. Counter must be braced to support the dis...
Section 2 installation instructions part number 020003997 4/12 2-3 location the location selected for the beverage dispenser must meet the following criteria. If any of these criteria are not met, select another location. • the air temperature must be at least 50°f (10°c), but must not exceed 95°f (...
Installation instructions section 2 2-4 part number 020003997 4/12 pre-installation checklist when installing any system, first make sure the major components are available. Generally the major components necessary for an installation are: essential tools - tubing cutters - oetiker pliers - phillips...
Section 2 installation instructions part number 020003997 4/12 2-5 top mounted ice machine installations note: for full information about icemaker installation, including plumbing lines connections and electrical requirements, see the icemaker installation manual. S series baffle installation 1. Rem...
Installation instructions section 2 2-6 part number 020003997 4/12 electrical general minimum circuit ampacity the minimum circuit ampacity is used to help select the wire size of the electrical supply. (minimum circuit ampacity is not the beverage/ice machine’s running amp load.) the wire size (or ...
Section 2 installation instructions part number 020003997 4/12 2-7 pump deck wiring the supply cord is equipped with a three prong 5-15p. When a ground fault circuit interrupter (gfci) is required by code, a breaker type protector must be used. We do not recommend gfic outlets as they are known for ...
Installation instructions section 2 2-8 part number 020003997 4/12 water supply recommended plumbing the plumbing diagram is printed on a white vinyl label, located above the inlet tubes for syrup and water. The plumbing diagram label can be accessed by removing the splash panel of the dispenser. Th...
Section 2 installation instructions part number 020003997 4/12 2-9 sv200/250 8 valve diagram 1 plumbing: 3-1-1-1-2 manifolding *optional* variety valve on #4 1 – water (thru coldplate) 2 – syrup (ambient) 3 – syrup (ambient) 4 – syrup (thru coldplate) note: syrup lines not shown pre-chill out to car...
Installation instructions section 2 2-10 part number 020003997 4/12 sv200/250 10 valve diagram internal carbonator tank (optional) plumbing: 3-1-2-1-3 manifolding pre-chill out to carbonator 8 7 6 5 4 3 3 2 1 1, 2, 3 4 5, 6 7 valves circuits co 2 manifold: change to carbonated or non-carbonated wate...
Section 2 installation instructions part number 020003997 4/12 2-11 flavor magic (for units with this feature) capacities specifications chart flavor 1 flavor 2 flavor 3 2 x 4 bib rack flavor 5 flavor 6 flavor 7 flavor 4 flavor 8 flavor 1 flavor 2 flavor 3 1 x 3 bib rack flavor 1 flavor 2 flavor 3 2...
Installation instructions section 2 2-12 part number 020003997 4/12 co 2 supply routing internal carb tank purge tube some models are equipped with an internal carbonation tank. These models require that the purge/pressure relief tubing be routed to a drain. 1. Remove the splash panel. 2. Uncoil tub...
Section 2 installation instructions part number 020003997 4/12 2-13 step by step installation general sv series dispensers have a stainless steel cabinet and lighted merchandiser standard. Beverage valves, coldplate connections, drain connections and electrical components are front serviceable. Spec...
Installation instructions section 2 2-14 part number 020003997 4/12 g. Loosen the bracket adjustment screws and pull the module toward you. This will allow for reinstallation of the merchandiser. H. Install merchandiser and adjust the selectable ice module so that it is flush with the front of the m...
Section 2 installation instructions part number 020003997 4/12 2-15 ada key pads these instructions are for installations with this option. 1. Remove power from the unit. Merchandiser removal 2. Loosen the two knurled fasteners located in the top of the merchandiser that hold the merchandiser in pla...
Installation instructions section 2 2-16 part number 020003997 4/12 ada key pad matrix finish installation 12. Put the splash panel and merchandiser back onto the unit and reinstall the screws that hold them in place. Restore power to the unit. Starting your beverage system & dispenser upon completi...
Part number 020003997 4/12 3-1 section 3 operation general system overview typical internal carbonation beverage dispensing system typical external carbonation (ambient) beverage dispensing system 1800 75 60 dispenser carbonator tank carbonate, non-carbonate beverage manifold countertop syrup tap wa...
Operation section 3 3-2 part number 020003997 4/12 component identification dispenser merchandiser soda valves key switch carb/non-carb water manifold and syrup/soda inlet (behind splash panel) drainpan grid drainpan splash panel counter cubed/crushed selectable ice module and/or *flavor magic * on ...
Section 3 operation part number 020003997 4/12 3-3 selectable ice module selectable ice module with flavor magic cubed / crushed touch pad module cover cubed / crushed touch pad flavor selection touch pad nozzle module cover.
Operation section 3 3-4 part number 020003997 4/12 sequence of operation ice recommended for dispensing dispensers are designed to dispense hard, cube ice up to one-inch square. The ice shapes and sizes listed above are recommended for dispensing. Warm “super cooled” ice before dispensing: “super co...
Section 3 operation part number 020003997 4/12 3-5 syrup delivery system your syrup location can vary depending on the volume of beverages served and ease of accessibility. Your beverage system may set in a back storage room or under the counter of the dispenser. Configurations are almost limitless....
Operation section 3 3-6 part number 020003997 4/12 figal system figal refers to the stainless steel tanks of pre-mix beverage or post-mix syrup. A small co 2 tank pushes the beverage out of the figal tank. Figal tanks the stainless steel figal beverage tanks are easy to store and connect. When using...
Section 3 operation part number 020003997 4/12 3-7 programming modes selectable ice non-adjustable agitation on units equipped with the selectable ice option, timed agitation for the unit is handled by the control board and is not adjustable. Note: this timer is re-settable, timed agitation every 3....
Operation section 3 3-8 part number 020003997 4/12 flavor magic dispensing modes for units with this option normal dispense with power applied to the control board, it will automatically start in dispense mode after a five (5) second delay. The led display will count down from four (4) to zero (0) a...
Section 3 operation part number 020003997 4/12 3-9 control logic matrix - flavor magic.
Operation section 3 3-10 part number 020003997 4/12 this page intentionally left blank.
Part number 020003997 4/12 4-1 section 4 maintenance preventive maintenance preventative maintenance is a vital part of keeping your dispenser in top condition. Following the guidelines below will assist you in continued trouble-free operation of your unit. 1. Conduct daily maintenance of the unit. ...
Maintenance section 4 4-2 part number 020003997 4/12 dispensing valves 1. Remove nozzles and diffusers from beverage valves. Nozzle removal 2. Rinse nozzle and diffuser with warm, clean water. 3. Clean nozzles and diffusers with soapy water and a soft bristle brush. 4. Clean the underside of the bev...
Section 4 maintenance part number 020003997 4/12 4-3 disassembly for cleaning & maintenance note: sanitize the ice dispenser at initial start-up in addition to monthly sanitizing. You will need a slotted screwdriver in order to disassemble. Disassemble parts in the following order: a. Merchandiser b...
Maintenance section 4 4-4 part number 020003997 4/12 selectable ice crusher once the ice crusher hub assembly has been removed the crusher is ready to be cleaned and sanitized. Follow the steps below for proper cleaning and sanitizing procedures. 1. Assure the unit is unplugged. 2. Mix a solution of...
Section 4 maintenance part number 020003997 4/12 4-5 5. Replace the ice door, crushed ice door, and crusher drip pan, slide until it snaps into place. 6. Reattach the decorative ice chute by inserting the chute rod through the chute, housing mount, and motor mount. Secure the chute rod by inserting ...
Maintenance section 4 4-6 part number 020003997 4/12 sanitizing beverage system cleaning sanitize the beverage system at initial start-up as well as regularly scheduled cleaning. The drain pan must be in place under soda valves, to carry away detergent and sanitizing agents that will be flushed thro...
Section 4 maintenance part number 020003997 4/12 4-7 5. Draw rinse water through system until clean water is dispensed. Most beverage valves allow the syrup side to be manually activated by depressing the syrup pallet. 6. Connect bucket 2 to system. 7. Draw detergent solution through system until so...
Maintenance section 4 4-8 part number 020003997 4/12 bag-in-box system sanitation the procedure below is for the sanitation of one syrup circuit at a time. Repeat to sanitize additional circuits. You will need the following items to clean and sanitize the bag-in-box (bib) beverage system: • three (3...
Section 4 maintenance part number 020003997 4/12 4-9 figal beverage system 1. Prepare the following in three clean figal tanks: • rinse tank - fill with room temperature tap water. • detergent tank - mix approved beverage system cleaner with warm water as directed. • sanitizing tank - mix a solution...
Maintenance section 4 4-10 part number 020003997 4/12 this page intentionally left blank.
Part number 020003997 4/12 5-1 section 5 before calling for service checklist if a problem arises during operation of your dispenser, follow the checklist below before calling service. Routine adjustments and maintenance procedures are not covered by the warranty. Dispenser general problem possible ...
Before calling for service section 5 5-2 part number 020003997 4/12 selectable ice problem possible cause to correct dispenser does not dispense crushed ice. Nothing is heard. No power. Check power source and power cord. Loose wire in electrical system. Check wiring. Dispense switch faulty replace s...
Section 5 before calling for service part number 020003997 4/12 5-3 drinks condition investigation check correction water only dispensing no pressure regulator(s) out of adjustment check/adjust regulator(s). Out of co 2 install fresh tank. Defective regulator(s) check/repair/replace regulator(s). Co...
Before calling for service section 5 5-4 part number 020003997 4/12 flavor shots pump problem possible cause corrective action flavor shot syrup does not dispense when flavor button is depressed. Syrup supply depleted. Replace syrup. Co 2 supply depleted. Replace co 2 . Bib disconnect loose or packe...
Section 5 before calling for service part number 020003997 4/12 5-5 this page intentionally left blank.
Before calling for service section 5 5-6 part number 020003997 4/12 this page intentionally left blank.
Manitowoc foodservice 2100 future drive sellersburg, in 47172, usa ph: 812-246-7000 fax: 812-246-7024 visit us online at: www.Manitowocfsg.Com © 2012 manitowoc continuing product improvements may necessitate change of specifications without notice. Part number 020003997 4/12.