1. DL manuals
  2. Valor
  3. Electric Heater
  4. 850
  5. Installer And Owner Manual

Valor 850 Installer And Owner Manual

Summary of 850

  • Page 1

    5139642/01 model 850 electric heater fitted with one of the following fascia: dream or petrus. (gc no. Ef-032-41) this guide is intended to help you install and care for your valor electric heater. Please read carefully before installing and using your heater. However, if further information is requ...

  • Page 2

    © baxi heating u.K. Limited 2011. All rights reserved. No part of this publication may be reproduced in any material form (including photocopying), stored in any medium by electronic means (including in any retrieval system or database) or transmitted, in any form or by any means, whether electronic...

  • Page 3

    Customer care thank you for choosing valor. All valor heaters are designed to meet the most stringent quality, performance and safety requirements to provide our customers with many years of trouble free service. This guide aims to improve your understanding and appreciation of your new valor heater...

  • Page 4

    2. Handling and unpacking before continuing any further with the installation of this heater please read the following: important instructions.  the approximate lifting weight (kg) of the heater parts are listed below: model heat engine fascia optional spacer (see section 4) petrus 7.7 10.0 1.0* dr...

  • Page 5

     always use genuine spares supplied by valor or approved agents. Never  never leave children unsupervised in a room where the heater is on and unguarded.  never use the heater in a small room when occupied by persons not able to leave the room by themselves unless constantly supervised.  never o...

  • Page 6

    4. Optional spacer frame kit an optional spacer frame kit is obtainable either from your heater supplier or direct from valor sales. The kit is an 80mm deep spacer kit (kit number 0582631). This spacer enables the heater to be flat wall fixed. The kit is obtainable either from your heater supplier o...

  • Page 7

    6. Heater contents installer and owner guide © baxi heating u.K. Limited 2011. Page 7 contents qty. (not to scale) heater (may differ from that shown - hood not present on petrus models) 1 securing clamp 1 m5 x 40mm securing clamp screw 1 no.8 x 3/8 pan head screw 5 tension wire 1 screw eye 1 wood s...

  • Page 8

    Page 8 © baxi heating u.K. Limited 2011. Installer and owner guide 7. Heater dimensions 8. Where and how can i fit the heater? Important: before continuing with the installation of this heater please ensure that you have completed the information on the last page of this guide. Please read this sect...

  • Page 9

    Page 9 © baxi heating u.K. Limited 2011. Installer and owner guide q do you want to fit the heater against a flat wall with the base of the heater on a hearth or similar surface? A you will need to purchase the optional spacer frame kit. This spacer enables the heater to be flat wall fixed. Please r...

  • Page 10

    General notes to read before fitting your heater.  if fitting the heater onto a reflective or shiny surface such as a hearth we recommend that this surface does not extend further than 300mm from the fixing plane (wall). Reflective or shiny surfaces that project further than 300mm may reflect an im...

  • Page 11

    The mains cable guides. At the base of the heater you will find two electric cable guides, one each side of the heater. If required, the cable guide on the right hand side (looking from the front of the heater) can be removed and put in the rectangular slot in the centre rear of the heater. For remo...

  • Page 12

    Securing the heater. The heater must be secured into position to prevent it from being tipped over. The following securing options are available: method a - securing the heater with screws. Method b - securing the heater with wire. Method c - securing the heater using the optional spacer frame (kit ...

  • Page 13

    Method b - securing with wire. This method of securing is recommended where the wall / brickwork is in poor condition or where marble back panels / surrounds are used. Although this section deals with fireplace openings without a spacer, this method of securing the heater it can also be used with th...

  • Page 14

    Page 14 © baxi heating u.K. Limited 2011. 11. Locate the heater in the fireplace opening, then from the front of the heater, gently pull the wire on the right hand side to gather up the excess until the heater is secure. Thread the wire through the remaining small hole to lock the wire and heater in...

  • Page 15

    Page 15 © baxi heating u.K. Limited 2011. Method d - securing with the clamp. This method of securing cannot be used in conjunction with the optional spacer frame. This is an alternative securing method where fixing to a surround or rear wall proves impractical. 1. Locate the clamp as in item 1 of f...

  • Page 16

    Page 16 © baxi heating u.K. Limited 2011. 9. Light shutter adjustment the light shutter is an adjustable plate that increases and decreases the appearance of the flames in the flame effect. 1. Switch on the fuel effect. If you are satisfied with the appearance of the flame effect there is no need to...

  • Page 17

    Page 17 © baxi heating u.K. Limited 2011. 10. Fitting the fascia fitting the infill trim (petrus model only). 1. Remove the infill trim from its packaging. 2. Locate the four tabs on the rear of the infill trim into the four slotted holes in the heater (see figure 18). Fitting the infill trim (dream...

  • Page 18

    Page 18 © baxi heating u.K. Limited 2011. Fitting the firefront and ash pan (petrus model only). 1. Remove the firefront from its packaging. 2. The rear of the firefront may be fitted with hanging screws or they may be supplied in the firefront packaging. Where they are not already fitted insert the...

  • Page 19: There?

    Page 19 © baxi heating u.K. Limited 2011. Pressing the ‘lamp’ button. This turns the effect on. The indicator lamp (see figure 24) will flash green for approximately five seconds, after this time the lamp will no longer be visible. An internal fan is used to produce the flickering flame effect, room...

  • Page 20

    Page 20 © baxi heating u.K. Limited 2011. What does the button do? Press the button once. This turns the effect on. The indicator lamp will flash green for approximately five seconds, after this time the lamp will no longer be visible. Press the button a second time. This will turn the 675 watt heat...

  • Page 21

    Page 21 © baxi heating u.K. Limited 2011. 13. Help and advice i have a problem with my heater! 1. My remote control does not work. The batteries in the remote control handset probably need replacing - see section 8 and figure 6. The heater can be operated manually as on pages 19 and 20. 2. My heater...

  • Page 22: Environmental Protection.

     model, name and serial number (this information can be found on a small label attached to the lower right of the heater (see figure 23) and should also have been recorded on the last page of this guide. 14. Environment environmental protection. Waste electrical products should not be disposed of w...

  • Page 23

    You must register your heater with heateam, the service division of baxi heating uk limited, either by completing and returning the registration card or calling our free telephone registration line on 0800 032 72 44. Our promise to you if you experience a fault with your new heater, we aim to provid...

  • Page 24

    © baxi heating u.K. Limited 2011. Page 24 installer and owner guide d d m m y y date of installation fascia name (block capitals) model 8 5 0 serial number (a label containing this information may have been placed below or can be found on the serial number label - see figure 28) brand customer: plea...