Wavecom TnP-500 User Manual - Important Information
Wavecom Instruments Fully Integrated Test N Print Unit - User Manual
4
Important Information
In the box
Integrated Test N Print System
User Manual/Quick Start Guide
IEC Test Lead (500mm Orange)
WCM Keyboard
USB A to USB B Interface Cable
Wavecom Scanner
Serial Scanner Cable
Wavecom TT-040-50
1 x Roll /500 Labels - 1 x Resin Ribbon
WinPATS Software (Full Version - Asset Management)
Earth Lead with Alligator Clip (1800mm black)
Self-Contained in Heavy Duty Case
Locking IEC Power Cable (1800mm Blue)
Manufacturer’s 1
st
Calibration Certificate
(Valid for 12 months from date of purchase)
Important:
Please register your WinPATS Software and Test N Print Unit with the provided documentation or online via
our website
www.wavecom.com.au
Precautions
Unique Locking Power Cable – For whole TnP Range
Please make sure yellow lever is pressed prior to removal of the locking power supply cable - 10A & 20A Models. Failure to do so,
combined with excessive force may damage the panel. This revolutionary locking, removable cable is intended not to dislodge during
test procedures.
Note: 10A ver. plug illustrated. 20A ver. is similar.
[
Following are for TnP 500B series with internal lithium-ion battery.
Switch from battery power to mains power
To switch from battery power to mains power, simply plug in the supplied power cord and connect to mains. Unit will automatically
switch to mains. Turning off Main Red Neon switch on left top corner will turn off the unit completely.
Switching from mains power to Battery Power or Turning On /Off unit on Battery power
When unit is not connected to mains, simply press and hold ENTER button on the unit till unit starts. Use the same button to turn off
the unit.
Mains Supply tests, Leakage tests and Meter Mode functions are not available on battery power. To perform RCD Tests, unit
is required to be connected to mains power. [Make sure that battery isolation switch located underneath the keyboard is ON all
the time while operating the unit & performing tests.]
To Charge the battery
Internal lithium-ion battery is of 97.92Wh, 6800mAh. It gets charged automatically while unit is connected to mains. It takes around
four hours to charge it fully. While charging, a battery symbol on top right corner of LCD screen will show how much it has been
charged and how much is left.
While it’s charging and user is not using the unit, display can be turned off by pressing and holding the same ENTER button. This will
bring a charging information display and decrease the brightness of LCD screen. Once battery is full charged and it is still connected
to mains, battery symbol will convert to plug symbol. It is advised not to put unit to charge when it is unattended or overnight.
Warnings:
Operating Environment: Charging – 0ᴼ to ~45ᴼC; Discharging - -20ᴼ to ~ 60ᴼC.
Please keep unit away from extreme exposed heat or extreme warm environment where typical temperature is above 60ᴼ. Please
keep unit safe and secured from free-fall or physical pressures, trauma or drop from heights.
Please do not open Battery compartment which is located behind the printer, unless user suspects that battery is damaged or smoke
is detected. Robust design and studies has been carried out while unit was under development and all possible safety concerns are
taken care of in this regards. It is still advised not to be opened. Damaged lithium ion batteries are not allowed for transportation.
Please speak to support team at Wavecom @ +61 08 8243 3500. Battery can simply be removed by opening a black cover behind the
printer, which should only be done in case of damage.
If sending unit for calibration, please turn off the battery isolation switch which is located underneath the keyboard.
Storage Warning: Please store the unit as per operating environment, do not leave unit where temperature can rise above 60ᴼ C
]
For units with wireless scanner, please note that user have to press and hold yellow trigger button on scanner till It lights up and
beeps. Long beep will confirm the connection between unit and scanner. Please let scanner charge for some time once in a while,
when unit is connected to mains. Wireless Scanner charges through the dock, please make sure that scanner is docked properly and
red LED flashes on scanner, indicating charge mode. Scanner battery and internal main TnP Li battery charges simultaneously while
being on Mains power, in case of TnPBW & TnPBWX units.
“If required, TnP firmware can be updated by Wavecom Instruments only to comply with potential changes in testing standards.”