1. DL manuals
  2. Worx
  3. Chainsaw
  4. WG303E
  5. Safety And Operating Manual

Worx WG303E Safety And Operating Manual

Summary of WG303E

  • Page 1

    Chain saw wg303e safety and operating manual original instructions.

  • Page 2: Chain Saw

    2 chain saw wg303e general power tool safety warnings warning: read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in th...

  • Page 3: Chain Saw

    3 chain saw wg303e dust collection can reduce dust-related hazards. 4) power tool use and care a) do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. B) do not use the power tool ...

  • Page 4: Chain Saw

    4 chain saw wg303e 8. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance. 9. Carry the chain saw by the front handle with the chain saw switched off and away from your body. When transporting or storing ...

  • Page 5: Chain Saw

    5 chain saw wg303e diagonally to the rear of the expected line of fall as illustrated in figure 1. Before felling is started, consider the natural lean of the tree, the location of larger branches and the wind direction to judge which way the tree will fall. Remove dirt, stones, loose bark, nails, s...

  • Page 6: Chain Saw

    6 chain saw wg303e 5. Bucking a log bucking is cutting a log into lengths. It is important to make sure your footing is firm and your weight is evenly distributed on both feet. When possible, the log should be raised and supported by the use of limbs, logs or chocks. Follow the simple directions for...

  • Page 7: Chain Saw

    7 chain saw wg303e remove plug from the mains immediately if the cable is damaged or cut. Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. Symbols read the manual warning...

  • Page 8: Chain Saw

    8 chain saw wg303e 4 5 6 7 8 9 10 13 14 15 17 16 11 12 3 2 18 14 1.

  • Page 9: Chain Saw

    9 chain saw wg303e 1. Rear handle 2. On/off switch 3. Lock-off button 4. Oil filler cap 5. Activation lever for kickback brake(hand guard) 6. Front handle 7. Guide bar 8. Chain 9. Spiked bumper 10. Locking knob/ chain tensioning adjustment knob 11. Cover plate 12. Blade protection cover 13. Drive sp...

  • Page 10: Chain Saw

    10 chain saw wg303e technical data type wg303e (3- designation of machinery, representative of chain saw) voltage 220-240v~50/60hz rated power 2000w bar length 400mm chain speed 12m/s oil tank capacity 200ml chain pitch 3/8” number of chain links 57 chain gauge 0.05” saw chain type es:91vg bar type ...

  • Page 11: Chain Saw

    11 chain saw wg303e and the tool is being used as intended by its design and these instructions. This tool may cause hand-arm vibration syndrome if its use is not adequately managed warning: to be accurate, an estimation of exposure level in the actual conditions of use should also take account of a...

  • Page 12: Chain Saw

    12 chain saw wg303e intended use the chain saw is intended for sawing of trees, tree trunks, branches, wooden beams, planks, etc. Cuts can be sawed with or across the grain. This product is not suitable for sawing mineral materials. Assembly warning! Do not connect the chain saw to mains before it i...

  • Page 13: Chain Saw

    13 chain saw wg303e tensioning chain always check the chain tension before use, after the first cuts and regularly during use, approx. Every 10 minutes. Upon initial operation, new chains can lengthen considerably. Warning: unplug chain saw from power source before adjusting saw chain tension. Warni...

  • Page 14: Chain Saw

    14 chain saw wg303e 4. Avoid dirt or debris entering oil tank, refit oil filler cap (4) and tighten. Important: to allow venting of the oil reservoir, small breather channels are provided between the oil filler cap and the strainer, to prevent leakage ensure machine is left in a horizontal position ...

  • Page 15: Chain Saw

    15 chain saw wg303e cutting - is the oil reservoir filled? Check oil level gauge (19) prior to starting and regularly during operation. Refill oil when oil level is low. The oil tank filling will last approx. 16minutes, depending on sawing intensity and stops. (see fig. H) - is the chain tension in ...

  • Page 16: Chain Saw

    16 chain saw wg303e general behavior always hold the chain saw firmly with both hands. Front grip with the left hand and rear grip with the right hand. Fully grip both handles at all times during operation. Never operate chain saw using only one hand. Ensure power cord is located to the rear, away f...

  • Page 17: Chain Saw

    17 chain saw wg303e when working on a slope, operate above or to the side of the trunk or laying tree. Be careful not to trip over tree stumps, branches, roots, etc. Cutting wood under tension (see fig. L) there is a high risk of accidents when sawing wood, branch or trees under tension. Be extremel...

  • Page 18: Chain Saw

    18 chain saw wg303e if the chain bar is worn out or damaged, take the chain tensioning catch off the bar by loosing the screw anti- clockwise. Then fit the tensioning catch into the new bar by tightening the screw clockwise. The catch protrude (a) must be fitted into the bar hole. (see fig m) sharpe...

  • Page 19: Chain Saw

    19 chain saw wg303e troubleshooting symptom possible cause chain saw fails to operate kickback brake is activated no power mains socket faulty extension cord damaged fuse faulty pull hand guard back in position (figure g) check power use another socket check cord, replace replace fuse chain saw oper...

  • Page 20: Plug Replacement

    Plug replacement (only for rewirable plug of uk & ireland) if you need to replace the fitted plug then follow the instructions below. Important the wires in the mains lead are colored in accordance with the following code: blue – neutral brown – live as the colors of the wires in the mains lead of t...

  • Page 24

    Copyright © 2015, positec. All rights reserved. Ar01166300 www.Worx.Com.