1. DL manuals
  2. Anritsu
  3. Remote Control
  4. MS2690A
  5. Operation manual

Anritsu MS2690A Operation manual

Manual is about: Signal Analyzer Spectrum Analyzer Function Remote Control

Summary of MS2690A

  • Page 1

    Document no.: m-w2855ae-47.0 anritsu corporation • for safety and warning information, please read this manual before attempting to use the equipment. • additional safety and warning information is provided within the ms2690a/ms2691a/ms2692a signal analyzer operation manual (mainframe operation), ms...

  • Page 2: Danger

    Ii safety symbols to prevent the risk of personal injury or loss related to equipment malfunction, anritsu corporation uses the following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the symbols before using the equipment. Some or all of t...

  • Page 3

    Iii notes on export management this product and its manuals may require an export license/approval by the government of the product's country of origin for re-export from your country. Before re-exporting the product or manuals, please contact us to confirm whether they are export-controlled items o...

  • Page 4

    Iv.

  • Page 5: About This Manual

    I about this manual operation manual configuration the operation manual configuration of the ms2690a/ms2691a/ms2692a and ms2830a/ms2840a signal analyzer is shown below. Ms2690a/ms2691a/ms2692a signal analyzer operation manual (main frame operation) ms2690a/ms2691a/ms2692a and ms2830a/ms2840a signal ...

  • Page 6

    Ii • signal analyzer operation manual (mainframe operation) • signal analyzer operation manual (mainframe remote control) description of basic operations, maintenance procedures, common functions and common remote functions of the mainframe • signal analyzer operation manual (signal analyzer functio...

  • Page 7: Table Of Contents

    1 iii 2 3 4 table of contents about this manual ....................................... I chapter 1 overview ................................... 1-1 1.1 overview .................................................................... 1-2 chapter 2 scpi device message details .. 2-1 2.1 frequency/span.....

  • Page 8

    Iv. Chapter 3 native device message list ..... 3-1 3.1 ieee488.2 common device messages .................... .. 3-3 3.2 application common device messages .................... .. 3-5 3.3 frequency/span settings .......................................... .. 3-7 3.4 level settings .......................

  • Page 9

    Chapter 1 overview 1-1 1 o ver view this chapter provides an overview of the remote control of the spectrum analyzer function (hereinafter, referred to as “this application”). 1.1 overview ....................................................................... 1-2.

  • Page 10: 1.1  Overview

    Chapter 1 overview 1-2. 1.1 overview automatic measurement can be performed by using this instrument in connection with an external controller (pc). This instrument is standard equipped with gpib, ethernet, and usb interfaces. You can also select a remote control command from the scpi mode, which is...

  • Page 11

    Chapter 2 scpi device message details 2-1 2 sc pi d ev ice m es sa ge d et ail s this chapter describes detailed specifications on scpi remote control commands for executing functions of this application in alphabetical order. Refer to the ms2690a/ms2691a/ms2692a and ms2830a/ms2840a signal analyzer ...

  • Page 12

    Chapter 2 scpi device message details 2-2 :unit:power? ........................................................................................................................ 2-67 :display:window[1]:trace:y[:scale]:linear:pdivision .................................. 2-68 :display:window[1]:trace:y[...

  • Page 19

    Chapter 2 scpi device message details 2-9 2 sc pi d ev ice m es sa ge d et ail s :calculate:acpower:carrier[1]:rcarrier ......................................................... 2-355 [:sense]:acpower:carrier[1]:rcarrier? ........................................................................... 2-...

  • Page 21

    Chapter 2 scpi device message details 2-11 2 sc pi d ev ice m es sa ge d et ail s :read:acp[n]? ....................................................................................................................... 2-415 :measure:acp[n]? ................................................................

  • Page 24

    Chapter 2 scpi device message details 2-14 [:sense]:chpower:frequency:center? ............................................................................ 2-483 :calculate:chpower:frequency:center? ........................................................................ 2-483 [:sense]:chpower:bandwi...

  • Page 25

    Chapter 2 scpi device message details 2-15 2 sc pi d ev ice m es sa ge d et ail s :display:chpower:view[1]:window[1]:trace:y[:scale]:pdivision? .............................. 2-507 :display:chpower:view[1]:window[1]:trace:y[:scale]:rlevel ......................... 2-508 :display:chpower:view[1]:wind...

  • Page 27

    Chapter 2 scpi device message details 2-17 2 sc pi d ev ice m es sa ge d et ail s :trigger:obwidth[:sequence]:source? ............................................................................ 2-556 [:sense]:obwidth:average:count .......................................................................

  • Page 33

    Chapter 2 scpi device message details 2-23 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:frequency:start ,,,,,,,,, ,,,,,,,, ,, .................................................................................. 2-734 [:sense]:spurious[:range][:list]:frequency:start? ...........

  • Page 36

    Chapter 2 scpi device message details 2-26 :calculate:spurious[:range][:list]:limit:absolute[:upper]:data:stop ,,,,,,,, ,,,,,,, ,,,, ....................................... 2-776 :calculate:spurious[:range][:list]:limit:absolute[:upper]:data:stop? .................... 2-777 [:sense]:spurious[:range]...

  • Page 37

    Chapter 2 scpi device message details 2-27 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious:tdomain[:range][:list]:sweep:time ,,,,, ,,,,, ,,,,, ,,,, ........... 2-791 [:sense]:spurious:tdomain[:range][:list]:sweep:time? ............................................ 2-792 [:sense]:spurious:tdo...

  • Page 39

    Chapter 2 scpi device message details 2-29 2 sc pi d ev ice m es sa ge d et ail s :calculate:toi:frequency:im3:search? .......................................................................... 2-843 :configure:toi ........................................................................................

  • Page 40

    Chapter 2 scpi device message details 2-30 2.19 questionable status register ................................................................................................ 2-962 :status:questionable[:event]? .............................................................................................

  • Page 42: 2.1  Frequency/span

    Chapter 2 scpi device message details 2-32 2.1 frequency/span table 2.1-1 lists device messages for frequency/span. Table 2.1-1 device messages for frequency/span function device messages center frequency [:sense]:frequency:center [:sense]:frequency:center? Frequency step size [:sense]:frequency:cen...

  • Page 43

    2.1 frequency/span 2-33 2 sc pi d ev ice m es sa ge d et ail s [:sense]:frequency:center center frequency function this command sets the center frequency. Command [:sense]:frequency:center parameter center frequency range [ms269xa] –100 mhz to 6.05 ghz (ms2690a) –100 mhz to 13.6 ghz (ms2691a) –100 m...

  • Page 44

    Chapter 2 scpi device message details 2-34 details this command is not available during the spurious emission measurement. When internal signal generator control on/off is on, the center frequency range depends on the frequency range of signal generator. Example of use to set the center frequency to...

  • Page 45

    2.1 frequency/span 2-35 2 sc pi d ev ice m es sa ge d et ail s [:sense]:frequency:center? Center frequency query function this command queries the center frequency. Command [:sense]:frequency:center? Response parameter center frequency range [ms269xa] –100 mhz to 6.05 ghz (ms2690a) –100 mhz to 13.6 ...

  • Page 46

    Chapter 2 scpi device message details 2-36 example of use to query the center frequency. Freq:cent? > 123456 [:sense]:frequency:center:step[:increment] frequency step size function this command sets the step size of the center, start and stop frequency. Command [:sense]:frequency:center:step[:increm...

  • Page 47

    2.1 frequency/span 2-37 2 sc pi d ev ice m es sa ge d et ail s [:sense]:frequency:center:step[:increment]? Frequency step size query function this command queries the step size of the center, start and stop frequency. Query [:sense]:frequency:center:step? Response parameter step size range [ms269xa]...

  • Page 48

    Chapter 2 scpi device message details 2-38 [:sense]:frequency:offset frequency offset function this command sets the frequency offset. Command [:sense]:frequency:offset parameter offset range –100 to 100 ghz resolution 1 hz suffix code hz, khz, kz, mhz, mz, ghz, gz hz is used when omitted. Default v...

  • Page 50

    Chapter 2 scpi device message details 2-40 [:sense]:frequency:span frequency span function this command sets the frequency span. Command [:sense]:frequency:span parameter frequency span range [ms269xa] 0 hz, 300 hz to 6.15 ghz (ms2690a) 0 hz, 300 hz to 13.7 ghz (ms2691a) 0 hz, 300 hz to 26.7 ghz (ms...

  • Page 51

    2.1 frequency/span 2-41 2 sc pi d ev ice m es sa ge d et ail s details this command is not available during the spectrum emission mask measurement or the spurious emission measurement. Frequency span cannot be set to 0 hz when internal signal generator control on/off is on. Frequency span cannot be ...

  • Page 52

    Chapter 2 scpi device message details 2-42 [:sense]:frequency:span? Frequency span query function this command queries the frequency span. Query [:sense]:frequency:span? Response parameter frequency span range [ms269xa] 0 hz, 300 hz to 6.15 ghz (ms2690a) 0 hz, 300 hz to 13.7 ghz (ms2691a) 0 hz, 300 ...

  • Page 53

    2.1 frequency/span 2-43 2 sc pi d ev ice m es sa ge d et ail s related command this command has the same function as the following commands. [:sense]:acpower:frequency:span? [:sense]:chpower:frequency:span? [:sense]:obwidth:frequency:span? [:sense]:frequency:span:full full span function this command...

  • Page 54

    Chapter 2 scpi device message details 2-44 [:sense]:frequency:start start frequency function this command sets the start frequency. Command [:sense]:frequency:start parameter start frequency range [ms269xa] –100 mhz to 6.0499997 ghz (ms2690a) –100 mhz to 13.5999997 ghz (ms2691a) –100 mhz to 26.59999...

  • Page 55

    2.1 frequency/span 2-45 2 sc pi d ev ice m es sa ge d et ail s [:sense]:frequency:start? Start frequency query function this command queries the start frequency. Query [:sense]:frequency:start? Response parameter start frequency range [ms269xa] –100 mhz to 6.0499997 ghz (ms2690a) –100 mhz to 13.5999...

  • Page 56

    Chapter 2 scpi device message details 2-46 [:sense]:frequency:stop stop frequency this command sets the stop frequency. Command [:sense]:frequency:stop parameter stop frequency range [ms269xa] –99.9997 mhz to 6.05 ghz (ms2690a) –99.9997 mhz to 13.6 ghz (ms2691a) –99.9997 mhz to 26.6 ghz (ms2692a) [m...

  • Page 57

    2.1 frequency/span 2-47 2 sc pi d ev ice m es sa ge d et ail s example of use to set the stop frequency to 10 mhz. Freq:stop 10000khz [:sense]:frequency:stop? Stop frequency query function this command queries the stop frequency. Query [:sense]:frequency:stop? Response parameter stop frequency range...

  • Page 58

    Chapter 2 scpi device message details 2-48 [:sense]:frequency:span:zero zero span function this command sets the frequency span to 0 hz (time domain display). Command [:sense]:frequency:span:zero details when zero span is executed during other than the burst average measurement, the measure function...

  • Page 60

    Chapter 2 scpi device message details 2-50 [:sense]:frequency:band:mode? Frequency band mode query function this command queries the frequency band path. The frequency at which the path is switched to the preselector band or a path that does not pass through the preselector can be set with this func...

  • Page 61

    2.1 frequency/span 2-51 2 sc pi d ev ice m es sa ge d et ail s [:sense]:frequency:band:mode:state? Frequency band mode status query function this command queries the spurious mode status of the frequency band with the current measurement conditions. Query [:sense]:frequency:band:mode:state? Response...

  • Page 63

    2.1 frequency/span 2-53 2 sc pi d ev ice m es sa ge d et ail s parameter enables/disables coupling 1 the rbw, vbw, detection mode, and trace point are coupled (shared) between the time domain and the frequency domain. 0 the rbw, vbw, detection mode, and trace point for the time domain are separate f...

  • Page 64

    Chapter 2 scpi device message details 2-54 [:sense]:frequency:synthesis[:state]? Switching speed query function this command queries the switching speed of frequency. Query [:sense]:frequency:synthesis[:state]? Response parameter frequency switching speed bph the operation is done so as to improve t...

  • Page 65: 2.2  Level

    2.2 level 2-55 2 sc pi d ev ice m es sa ge d et ail s 2.2 level the table below shows device messages for level. Table 2.2-1 device messages for level function device message reference level :display:window[1]:trace:y[:scale]:rlevel :display:window[1]:trace:y[:scale]:rlevel? Rf attenuator [:sense]:p...

  • Page 66

    Chapter 2 scpi device message details 2-56 :display:window[1]:trace:y[:scale]:rlevel reference level function this command sets the reference level. Command :display:window[1]:trace:y[:scale]:rlevel parameter reference level range value equivalent to –120 to +50 dbm resolution 0.01 db (when scale un...

  • Page 67

    2.2 level 2-57 2 sc pi d ev ice m es sa ge d et ail s example of use to set the reference level to 0 dbm. Disp:wind:trac:y:rlev 0dbm related command this command has the same function as the following commands. :display:acpower:view[1]:window[1]:trace:y[:scale]:rleve l :display:chpower:view[1]:windo...

  • Page 68

    Chapter 2 scpi device message details 2-58 :display:window[1]:trace:y[:scale]:rlevel? Reference level query function this command queries the reference level. Query :display:window[1]:trace:y[:scale]:rlevel? Response parameter reference level range value equivalent to –120 to +50 dbm resolution 0.01...

  • Page 69

    2.2 level 2-59 2 sc pi d ev ice m es sa ge d et ail s [:sense]:power[:rf]:attenuation rf attenuator function this command sets the attenuation. Command [:sense]:power[:rf]:attenuation parameter attenuation range 0 to 60 db resolution [ms269xa] 2 db [ms2830a], [ms2840a] 2 db or 10 db refer to “table ...

  • Page 70

    Chapter 2 scpi device message details 2-60 [:sense]:power[:rf]:attenuation? Rf attenuator query function this command queries the attenuation. Query [:sense]:power[:rf]:attenuation? Response parameter attenuation range 0 to 60 db resolution [ms269xa] 2 db [ms2830a], [ms2840a] 2 db or 10 db refer to ...

  • Page 72

    Chapter 2 scpi device message details 2-62 [:sense]:power[:rf]:attenuation:auto? Rf attenuator auto/manual query function this command queries the on/off state of the automatic attenuation. Query [:sense]:power[:rf]attenuation:auto? Response parameter automatic attenuation is disabled/enabled. 0 dis...

  • Page 73

    2.2 level 2-63 2 sc pi d ev ice m es sa ge d et ail s :display:window[1]:trace:y[:scale][:logarithmic]:pdivision log scale range function this command sets the y-axis scale magnification when scale mode is set to log. Command :display:window[1]:trace:y[:scale][:logarithmic]:pdivisi on parameter y-ax...

  • Page 74

    Chapter 2 scpi device message details 2-64 :display:window[1]:trace:y[:scale][:logarithmic]:pdivision? Log scale range query function this command queries the y-axis scale magnification when scale mode is set to log. Query :display:window[1]:trace:y[:scale][:logarithmic]:pdivisi on? Response paramet...

  • Page 75

    Chapter 2 scpi device message details 2-76 [:sense]:correction:impedance[:input][:magnitude] 50

  • Page 77

    2.2 level 2-67 2 sc pi d ev ice m es sa ge d et ail s :unit:power? Log scale unit query function this command queries the level display unit system at log scale. Query :unit:power? Response parameter level display unit system at log scale dbm dbm dbmv dbmv dbuv dbµv dbuve dbmv (emf) v v w w dbuvm db...

  • Page 78

    Chapter 2 scpi device message details 2-68 :display:window[1]:trace:y[:scale]:linear:pdivision linear scale range function this command sets the y-axis scale magnification for the linear scale display. Command :display:window[1]:trace:y[:scale]:linear:pdivision parameter y-axis scale magnification 1...

  • Page 79

    2.2 level 2-69 2 sc pi d ev ice m es sa ge d et ail s example of use to query the scale magnification. Disp:wind:trac:y:lin:pdiv? > 5 :display:window[1]:trace:y[:scale][:logarithmic] log scale line function this command sets the number of y-axis scale segments in log scale mode. Command :display:win...

  • Page 80

    Chapter 2 scpi device message details 2-70 :display:window[1]:trace:y[:scale][:logarithmic]? Log scale line query function this command queries the number of y-axis segments in log scale mode. Query :display:window[1]:trace:y[:scale][:logarithmic]? Response parameter number of y-axis scale segments ...

  • Page 81

    2.2 level 2-71 2 sc pi d ev ice m es sa ge d et ail s :display:window[1]:trace:y[:scale]:rlevel:offset ref.Level offset value function this command sets the offset value of the reference level offset function. Command :display:window[1]:trace:y[:scale]:rlevel:offset parameter reference level offset ...

  • Page 83

    2.2 level 2-73 2 sc pi d ev ice m es sa ge d et ail s :display:window[1]:trace:y[:scale]:rlevel:offset:state? Reference level offset mode query function this command queries the on/off state of the reference level offset function. Command :display:window[1]:trace:y[:scale]:rlevel:offset:state? Respo...

  • Page 84

    Chapter 2 scpi device message details 2-74 details [ms269xa] this command is fixed to off and cannot be set when the option 008/108 6 ghz preamplifier is not installed. [ms2830a] this command is fixed to off and cannot be set when the option 008/108/068/168 preamplifier is not installed. [ms2840a] t...

  • Page 85

    2.2 level 2-75 2 sc pi d ev ice m es sa ge d et ail s :display:window[1]:trace:y[:scale]:line[:logarithmic] log scale line function this command sets the number of y-axis segments in log scale mode. Command :display:window[1]:trace:y[:scale]:line[:logarithmic] parameter number of y-axis scale segmen...

  • Page 89

    2.3 rbw/vbw 2-79 2 sc pi d ev ice m es sa ge d et ail s details in ms269xa, ms2830a, ms2840a rbw mode: normal • the resolution bandwidth auto setting is switched off when the resolution bandwidth (rbw) is changed. • for ms2830a, ms2840a rbw 20 mhz or greater is only available for ms2830a-005/105/007...

  • Page 91

    2.3 rbw/vbw 2-81 2 sc pi d ev ice m es sa ge d et ail s details in ms269xa, ms2830a, ms2840a rbw mode: normal • the resolution bandwidth auto setting is switched off when the resolution bandwidth (rbw) is changed. For ms2830a, ms2840a rbw 20 mhz or greater is only available for ms2830a-005/105/007/0...

  • Page 94

    Chapter 2 scpi device message details 2-84 parameter resolution bandwidth (rbw) [ms269xa] range/resolution 30 hz to 31.25 mhz however, the settable value is 30 hz to 3 mhz (for 1 to 3 sequences), 50 khz, 5 mhz, 10 mhz, or 20 mhz, or 31.25 mhz. [ms2830a], [ms2840a] rbw mode normal range/resolution 1 ...

  • Page 123

    2.4 marker 2-113 2 sc pi d ev ice m es sa ge d et ail s s is used when omitted. Details this command is not available during spurious emission measurement and when displayed segment mode is auto. Not available during spectrum emission mask measurement. When internal signal generator control on/off i...

  • Page 124

    Chapter 2 scpi device message details 2-114 when omitted: marker 1 center frequency of zone marker range [ms269xa] –100 mhz to 6.05 ghz (ms2690a) –100 mhz to 13.6 ghz (ms2691a) –100 mhz to 26.6 ghz (ms2692a) [ms2830a] –100 mhz to 3.7 ghz (option 040) –100 mhz to 6.1 ghz (option 041) –100 mhz to 13.6...

  • Page 126

    Chapter 2 scpi device message details 2-116 when frequency span is 0 hz, and active marker is maker 2. To move the center of marker 1 zone marker to +100 mhz of marker 2 (reference marker). Calc:mark1:ref 2 calc:mark1:x:delt 100mhz when frequency span is 0 hz, and active marker is maker 2. To move t...

  • Page 128

    Chapter 2 scpi device message details 2-118 to query the center of marker 1 zone marker in relative value. Calc:mark:x:delt? > 100000000.00 when frequency span is 0 hz, and active marker is maker 2. To move the center of marker 1 zone marker to 15 ms of marker 2 (reference marker). Calc:mark1:ref 2 ...

  • Page 131

    2.4 marker 2-121 2 sc pi d ev ice m es sa ge d et ail s marker number for reference 1 marker 1 2 marker 2 3 marker 3 4 marker 4 5 marker 5 6 marker 6 7 marker 7 8 marker 8 9 marker 9 10 marker 10 example of use to query the reference marker for the marker 2. Calc:mark2:ref? > 4 related command this ...

  • Page 134

    Chapter 2 scpi device message details 2-124 :calculate:marker:sline[:state]? Spot line query function this command queries the on/off state of the marker line display setting in spot marker. Query :calculate:marker:sline[:state]? Response parameter marker line display on/off 1 displays the marker li...

  • Page 135

    2.4 marker 2-125 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:couple:zone[:state]? Couple zone query function this command queries the on/off state of the zone width shared setting. Query :calculate:marker:couple:zone[:state]? Response parameter zone width shared setting on/off 1 on 0 of...

  • Page 153

    2.4 marker 2-143 2 sc pi d ev ice m es sa ge d et ail s when marker mode is delta and scale mode is log resolution: 0.001 db suffix code none. Value is returned in db units. –999.0 is returned at no measurement or error when marker mode is delta and scale mode is lin range 0.0000 to 10000 resolution...

  • Page 155

    2.4 marker 2-145 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:reference:x:position? Reference marker position query function this command queries the position of the marker specified by relative to of the active marker by the display points from the left edge of the screen. Query :calcul...

  • Page 156

    Chapter 2 scpi device message details 2-146 :calculate:marker:reference:x? Reference marker frequency (time) query function this command queries the frequency or time at the marker point set in relative to of the active marker. Query :calculate:marker:reference:x? Response parameter resolution 0.01 ...

  • Page 157

    2.4 marker 2-147 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:reference:y? Reference marker level query function this command queries the level data at the marker point set in relative to of the active marker. Query :calculate:marker:reference:y? Response parameter level at reference mar...

  • Page 159

    2.4 marker 2-149 2 sc pi d ev ice m es sa ge d et ail s when scale unit settings are v-system units. Resolution 0.001 db suffix code none. Value is returned in dbm units. –999.0 is returned when no measurement is performed or an error occurs. –999.0 is returned when marker mode is set to fixed or of...

  • Page 160

    Chapter 2 scpi device message details 2-150 :calculate:pmarker:delta:y? Power marker result query function this command queries the total power ratio and the power density ratio within the range of the zone marker, regarding the active marker and the marker specified by relative to. Query :calculate...

  • Page 161

    2.4 marker 2-151 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:aoff all marker off function this command sets all the markers to off. Command :calculate:marker:aoff details this command is not available during spurious emission measurement and when displayed segment mode is auto. Not avai...

  • Page 162

    Chapter 2 scpi device message details 2-152 :calculate:marker:readout? Marker readout query function this command queries all the marker values. Query :calculate:marker:readout? Response ,,,,..., , (in frequency domain) ,,,,..., , (in time domain) parameter frequency of maker n resolution 0.01 hz su...

  • Page 163

    2.4 marker 2-153 2 sc pi d ev ice m es sa ge d et ail s suffix code none. Value is returned in w units. –999.0 is returned when no measurement is performed, an error has occurred, or the marker is off. When marker level display units are x multiple-system units. Resolution 0.0001 suffix code none 1:...

  • Page 183

    2.5 signal search 2-173 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:peak:threshold peak search threshold level function this command sets the threshold when a peak point is detected. Command :calculate:marker:peak:threshold parameter threshold when searching for the peak point range ful...

  • Page 184

    Chapter 2 scpi device message details 2-174 :calculate:marker:peak:threshold? Peak search threshold level query function this command queries the threshold when searching for the peak point. Query :calculate:marker:peak:threshold? Response parameter threshold when searching for the peak point range ...

  • Page 187

    2.5 signal search 2-177 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:peak:threshold:mode? Peak search mode query function this command queries the detection mode for the threshold (peak search threshold level) when searching for the peak point. Query :calculate:marker:peak:threshold:mode...

  • Page 188

    Chapter 2 scpi device message details 2-178 :calculate:data:peaks[:logarithmic]? ,[,] all peak search and query function this command queries the frequency (or time) and level of all the peak points in the trace data of the active trace in a lump sum. Query :calculate:data:peaks[:logarithmic]? ,[,] ...

  • Page 189

    2.5 signal search 2-179 2 sc pi d ev ice m es sa ge d et ail s uw µw nw nw pw pw fw fw follows the setting of scale unit, when omitted. V is used when it is linear scale. When scale mode is log. Range 0.001 to 100.000 db suffix code db db is used even when omitted. When scale mode is lin. Range 0.01...

  • Page 190

    Chapter 2 scpi device message details 2-180 peak time resolution 0.01 µs suffix code none. Value is returned in s units. –999999999999 is returned when not measured or an error occurs. Example of use to query the frequency and level of the active trace at once. Calc:data:peak? –40.000,10.000 :calcul...

  • Page 191

    2.5 signal search 2-181 2 sc pi d ev ice m es sa ge d et ail s :calculate:marker:peak:sort:x search peaks sort x function this command sorts as many markers as the number set in search peaks number by frequency (time) on the trace. Command :calculate:marker:peak:sort:x details this command is not av...

  • Page 192

    Chapter 2 scpi device message details 2-182 :calculate:marker:peak:sort:count? Search peaks number query function this command queries the number of searches when executing search peaks sort y/x. Query :calculate:marker:peak:sort:count? Response parameter number of searches range 1 to 10 resolution ...

  • Page 197

    2.6 trace 2-187 2 sc pi d ev ice m es sa ge d et ail s :trace:active? Active trace query function this command queries the trace (active trace) to operate the marker. Command :trace:active? Response parameter type of trace to be activated a trace a b trace b c trace c d trace d e trace e f trace f e...

  • Page 202

    Chapter 2 scpi device message details 2-192 [:sense]:average:count average count function this command sets the storage count. Command [:sense]:average:count parameter storage count range 2 to 9999 default 10 details this command is not available during the spurious emission measurement. Example of ...

  • Page 203

    2.6 trace 2-193 2 sc pi d ev ice m es sa ge d et ail s [:sense]:average:count? Average count query function this command queries the storage count. Query [:sense]:average:count? Response parameter storage count range 2 to 9999 example of use to query the storage count. Aver:coun? > 110 command this ...

  • Page 204

    Chapter 2 scpi device message details 2-194 :trace:sweep:count? Sweep count query function this command queries the sweep count. Query :trace:sweep:count? Response parameter storage count range 2 to 9999 details during the spectrum emission mask measurement, the sweep count is displayed as a percent...

  • Page 219

    2.6 trace 2-209 2 sc pi d ev ice m es sa ge d et ail s gate view cannot be set when gate view is set to off. This command is not available when all the traces are set to blank. Example of use to save the waveform data file “trace” of trace b into e drive. Mmem:stor:trac trac2,"trace",e :mmemory:stor...

  • Page 221

    2.6 trace 2-211 2 sc pi d ev ice m es sa ge d et ail s > #44004 the “4” after “#” indicates that “this is followed by 4 characters indicating the binary data length.”“4004” indicates that “this is followed by 4004 bytes of binary data.” details this function writes or queries the trace data of the p...

  • Page 223

    2.6 trace 2-213 2 sc pi d ev ice m es sa ge d et ail s details this function queries the trace data of the negative detection, when the detection mode is positive & negative (normal mode). –999.0 is returned for traces a, b, c, d, e and f while spectrum emission mask measurement is performed. –999.0...

  • Page 225

    2.6 trace 2-215 2 sc pi d ev ice m es sa ge d et ail s example: if 1001 point trace data is read out when real,32 is set for :format[:data], > #44004 the “4” after “#” indicates that “this is followed by 4 characters indicating the binary data length.”“4004” indicates that “this is followed by 4004 ...

  • Page 227

    2.6 trace 2-217 2 sc pi d ev ice m es sa ge d et ail s example: if 1001 point trace data is read out when real,32 is set for :format[:data], > #44004 the “4” after “#” indicates that “this is followed by 4 characters indicating the binary data length.”“4004” indicates that “this is followed by 4004 ...

  • Page 229

    2.6 trace 2-219 2 sc pi d ev ice m es sa ge d et ail s :format:border? Binary data byte order query function this command reads the byte order of the query data when real,32 or integer,32 is set for :format[:data]. Query :format:border? Response parameter byte order norm byte order: big endian swap ...

  • Page 231

    2.6 trace 2-221 2 sc pi d ev ice m es sa ge d et ail s :format[:data]? Numeric data format query function this command queries the format of the data that is read out with [:sense]:data?. Query :format[:data]? Response , parameter data format asc ascii format. Real 32-bit binary floating point forma...

  • Page 247

    2.6 trace 2-237 2 sc pi d ev ice m es sa ge d et ail s :mmemory:delete:lline [,] delete limit data file function this command deletes the specified limit data file. Command :mmemory:delete:lline [,] parameter "name of limit data file to delete" string of up to 32 characters, not including the extens...

  • Page 248

    Chapter 2 scpi device message details 2-238 :mmemory:delete:lline:all [] delete all limit data files function this command deletes all limit data files stored in the specified drive. Command :mmemory:delete:lline:data:all [] parameter drive name a,b,d,e,f,... Defaults to d when omitted. Details from...

  • Page 249

    2.6 trace 2-239 2 sc pi d ev ice m es sa ge d et ail s :mmemory:delete:waveform [,] delete waveform data file function this command deletes the specified waveform data folder. Command :mmemory:delete:waveform [,] parameter "name of waveform data folder to delete" string of up to 32 characters, not i...

  • Page 250

    Chapter 2 scpi device message details 2-240 :mmemory:delete:waveform:all [] delete all waveform data files function this command deletes all waveform data folders and all files in those folders. Command :mmemory:delete:waveform:all [] parameter drive name a,b,d,e,f,... Defaults to d when omitted. De...

  • Page 252

    Chapter 2 scpi device message details 2-242 this command is available only for ms2830a. The destination trace means the selelcted trace. Trace-writing mode where store ref. Is executed is set to view. This cannot be executed under the following conditions: • internal signal generator control functio...

  • Page 253

    2.6 trace 2-243 2 sc pi d ev ice m es sa ge d et ail s :display:window[1]:trace:y[:scale]:nrlevel reference level (normalize) function this command sets the reference level when the normalize finction is performed. Command :display:window[1]:trace:y[:scale]:nrlevel parameter reference level range –1...

  • Page 254

    Chapter 2 scpi device message details 2-244 :calculate:math ,[,,] math function this command performs calculations between traces. Command :calculate:math ,[,,race>] parameter type of trace to be activated trace1 trace a (default) trace2 trace b trace3 trace c trace4 trace d trace5 trace e trace6 tr...

  • Page 255

    2.6 trace 2-245 2 sc pi d ev ice m es sa ge d et ail s • when the measure function is on • when signal identifier is on • when the normalize function is on • when gate view is on when scale mode is linear, calculation type is not set to the log caluculation (ldifference, lsum). This cannot set trace...

  • Page 256

    Chapter 2 scpi device message details 2-246 :calculate:math? Math query function this command queries the math setting of trace. Query :calculate:math? Response ,, parameter type of trace trace1 trace a trace2 trace b trace3 trace c trace4 trace d trace5 trace e trace6 trace f calculation type off d...

  • Page 261

    2.7 sweep/trigger/gate 2-251 2 sc pi d ev ice m es sa ge d et ail s :initiate:mode:continuous continuous measurement function this command sets the sweep mode to continuous and starts continuous sweep. Command :initiate:mode:continuous example of use to start continuous sweep. Init:mode:cont :initia...

  • Page 262

    Chapter 2 scpi device message details 2-252 :initiate[:immediate] initiate function this command starts sweeping in the presently set sweep mode. Command :initiate:[immediate] details to read out the measurement results after executing this command, perform the synchronization control using the “*wa...

  • Page 263

    2.7 sweep/trigger/gate 2-253 2 sc pi d ev ice m es sa ge d et ail s :initiate:swp? Single sweep query function this command queries the sweep status (sweep done/during sweep). Query :initiate:swp? Response parameter sweep status 0 sweep done 1 during sweep example of use to query the sweep status. I...

  • Page 264

    Chapter 2 scpi device message details 2-254 2 ms (option 041) 4 ms (option 043) 89 ms (option 044) 86 ms (option 045) [ms2840a] 1 ms (option 040) 2 ms (option 041) 89 ms (option 044) 86 ms (option 046) details this command is not available when in fft sweep. This command is not available during the ...

  • Page 265

    2.7 sweep/trigger/gate 2-255 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:time? Sweep time query function this command queries the sweep time. Each parameter is specified in accordance with the already-specified frequency axis or time axis measurement. Query [:sense]:sweep:time? Response pa...

  • Page 267

    2.7 sweep/trigger/gate 2-257 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:time:auto? Sweep time auto/manual query function this command queries the on/off state of the automatic sweep time setting function. Each parameter is specified in accordance with the already-specified frequency axis ...

  • Page 268

    Chapter 2 scpi device message details 2-258 parameter sweep time fast fast sweep mode (ms2830a, ms2840a default) normal normal sweep mode (ms269xadefault) details this command is not available during the spectrum emission mask measurement. Example of use to set the sweep time to normal sweep mode. S...

  • Page 269

    2.7 sweep/trigger/gate 2-259 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:points trace point function this command sets the number of the trace display points. When couple time/freq. Domain is set to off, each parameter is specified in accordance with the already-specified frequency axis or...

  • Page 270

    Chapter 2 scpi device message details 2-260 [:sense]:sweep:points? Trace point query function this command queries the number of trace display points. When couple time/freq. Domain is set to off, each parameter is specified in accordance with the already-specified frequency axis or time axis measure...

  • Page 272

    Chapter 2 scpi device message details 2-262 [:sense]:sweep[:type][:auto]:rules? Auto sweep type select rules query function this command queries the rule for switching between sweep and fft during measurement. Query [:sense]:sweep[:type][:auto]:rules? Response parameter switching rules dran selects ...

  • Page 273

    2.7 sweep/trigger/gate 2-263 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep[:type][:auto]:rules:fft:width sweep type select rules fft width function this command sets the fft width when fft priority is selected, for the sweep/fft switching rules during measurement. Command [:sense]:sweep[:typ...

  • Page 274

    Chapter 2 scpi device message details 2-264 [:sense]:sweep[:type][:auto]:rules:fft:width? Sweep type select rules fft width query function this command queries the fft width when fft priority is selected, for the sweep/fft switching rules during measurement. Query [:sense]:sweep[:type][:auto]:rules:...

  • Page 275

    2.7 sweep/trigger/gate 2-265 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep[:type][:auto]:rules:fft:rwidth? Sweep type select rules real fft width query function this command queries the fft width that is actually used for the sweep/fft switch rule during measurement. Query [:sense]:sweep[:ty...

  • Page 276

    Chapter 2 scpi device message details 2-266 [:sense]:sweep[:type][:auto]:rules:rtype? Sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during measurement. Query [:sense]:sweep[:type][:auto]:rules:rtype? Response parameter sweep mode...

  • Page 278

    Chapter 2 scpi device message details 2-268 related command this command has the same function as the following commands. [:sense]:acpower:detector[:function] [:sense]:chpower:detector[:function] [:sense]:obwidth:detector[:function] :calculate:detector[:function] :calculate:acpower:detector[:functio...

  • Page 279

    2.7 sweep/trigger/gate 2-269 2 sc pi d ev ice m es sa ge d et ail s example of use to query the detection mode. Det? > pos related command this command has the same function as the following commands. [:sense]:acpower:detector[:function]? [:sense]:chpower:detector[:function]? [:sense]:obwidth:detect...

  • Page 280

    Chapter 2 scpi device message details 2-270 :calculate:detector[:function]? Detection mode query function this command selects the detection mode of the waveform pattern. When couple time/freq. Domain is set to off, each parameter is specified in accordance with the already-specified frequency axis ...

  • Page 281

    2.7 sweep/trigger/gate 2-271 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence][:state]? Trigger switch query function this command queries the on/off state of the trigger sweep. Query :trigger[:sequence][:state]? Response parameter trigger sweep on/off 0 does not perform trigger sweep. 1 pe...

  • Page 283

    2.7 sweep/trigger/gate 2-273 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:source? Trigger source query function this command queries the trigger source. Query :trigger[:sequence]:source? Response parameter trigger signal source [ms269xa] ext external input (external) imm free run wif w...

  • Page 285

    2.7 sweep/trigger/gate 2-275 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:video:level[:logarithmic]? Log scale video trigger level query function this command queries the threshold of the level where trigger sweep starts in video trigger in log scale mode. Query :trigger[:sequence]:vid...

  • Page 286

    Chapter 2 scpi device message details 2-276 :trigger[:sequence]:video:level:linear? Linear scale video trigger level query function this command queries the threshold of the level where trigger sweep starts in video trigger in linear scale mode. Query :trigger[:sequence]:video:level:linear? Response...

  • Page 289

    2.7 sweep/trigger/gate 2-279 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:external[1]:slope? Trigger slope query function this command queries the trigger detection mode (rise/fall). Query :trigger[:sequence]:external[1]:slope? Response parameter trigger detection mode pos detects at t...

  • Page 291

    2.7 sweep/trigger/gate 2-281 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:video:slope? Trigger slope query function this command queries the detection mode for the trigger (rise/fall). Refer to :trigger[:sequence]:external[1]:slope? Related command this command has the same function as...

  • Page 292

    Chapter 2 scpi device message details 2-282 :trigger[:sequence]:external[1]:delay? Trigger delay query function this command queries the delay from the trigger occurrence point to sweep start. Query :trigger[:sequence]:external[1]:delay? Response parameter delay time to the time when the gate starts...

  • Page 294

    Chapter 2 scpi device message details 2-284 :trigger[:sequence]:holdoff trigger hold function this command sets the time during which trigger input is disabled for a set time, from the first trigger input until the next trigger input. Command :trigger[:sequence]:holdoff parameter offset time range 0...

  • Page 295

    2.7 sweep/trigger/gate 2-285 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:holdoff? Trigger hold query function this command queries the time during which trigger input is disabled for a set time from the first trigger input until the next trigger input. Query trigger[:sequence]:holdoff...

  • Page 296

    Chapter 2 scpi device message details 2-286 details this command is not available for ms269x series. The trigger (on/off) function is automatically set to on when this function is set to on. This function cannot be set in the case of video trigger. Example of use to set the trigger input disable tim...

  • Page 297

    2.7 sweep/trigger/gate 2-287 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:frame:period frame trigger period function this command sets the trigger occurrence period of the frame trigger. Command :trigger[:sequence]:frame:period parameter frame trigger range 1 µs to 1 s resolution 10 ns...

  • Page 298

    Chapter 2 scpi device message details 2-288 :trigger[:sequence]:frame:period? Frame trigger period query function this command queries the frame trigger occurrence period. Query :trigger[:sequence]:frame:period? Response parameter delay time until gate start range 1 µs to 1 s resolution 10 ns suffix...

  • Page 300

    Chapter 2 scpi device message details 2-290 :trigger[:sequence]:frame:sync? Frame sync source query function this command queries the synchronization signal source for frame trigger start. Query :trigger[:sequence]:frame:sync? Response parameter synchronized signal source ext external input imm free...

  • Page 301

    2.7 sweep/trigger/gate 2-291 2 sc pi d ev ice m es sa ge d et ail s :trigger[:sequence]:frame:offset frame sync offset function this command sets the offset time from frame trigger occurrence signal source input until the frame trigger occurrence. Command :trigger[:sequence]:frame:offset parameter o...

  • Page 302

    Chapter 2 scpi device message details 2-292 :trigger[:sequence]:frame:offset? Frame sync offset query function this command queries the offset time from the frame trigger occurrence signal source input until the frame trigger occurrence. Query :trigger[:sequence]:frame:offset? Response parameter off...

  • Page 305

    2.7 sweep/trigger/gate 2-295 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:source? Gate source query function this command queries the gate signal source. Command [:sense]:sweep:egate:source? Response parameter trigger signal source [ms269xa] ext external input (external) imm free run ...

  • Page 308

    Chapter 2 scpi device message details 2-298 [:sense]:sweep:egate:slope? Gate slope query function this command queries the detection mode for the gate signal. Query [:sense]:sweep:egate:slope? Response parameter detection mode for gate signal pos detects at the rising edge. Neg detects at the fallin...

  • Page 309

    2.7 sweep/trigger/gate 2-299 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:delay gate delay function this command sets the delay time to start the gate sweep. Command [:sense]:sweep:egate:delay parameter delay time to start the gate. Range 0 to 1 s resolution 20 ns suffix code ns, us, ...

  • Page 310

    Chapter 2 scpi device message details 2-300 [:sense]:sweep:egate:length gate length function this command sets the time length of the gate. Command [:sense]:sweep:egate:length parameter time length of the gate range 50 µs to 1 s resolution 20 ns suffix code ns, us, ms, s s is used when omitted. Exam...

  • Page 312

    Chapter 2 scpi device message details 2-302 [:sense]:sweep:egate[:view]:time gate view sweep time function this command sets the sweep time for gate view. This parameter and the one for setting the sweep time for time axis measurement reference the same value. Command [:sense]:sweep:egate[:view]:tim...

  • Page 314

    Chapter 2 scpi device message details 2-304 [:sense]:sweep:egate:view:bandwidth[:resolution]:auto? Gate view resolution bandwidth auto/manual query function this command queries the automatic resolution bandwidth (rbw) setting for gate view. This parameter and the one for automatically setting the r...

  • Page 315

    2.7 sweep/trigger/gate 2-305 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:view:bandwidth[:resolution] gate view resolution bandwidth function this command sets the resolution bandwidth (rbw) for gate view. This parameter and the one for setting the rbw for time axis measurement refere...

  • Page 316

    Chapter 2 scpi device message details 2-306 [:sense]:sweep:egate:view:bandwidth[:resolution]? Gate view resolution bandwidth query function this command selects the resolution bandwidth (rbw) for gate view. This parameter and the one for setting the rbw for time axis measurement reference the same v...

  • Page 318

    Chapter 2 scpi device message details 2-308 [:sense]:sweep:egate:view:bandwidth:video gate view video bandwidth function this command sets the video bandwidth (vbw) for gate view. This parameter and the one for setting the vbw for time axis measurement reference the same value. Command [:sense]:swee...

  • Page 319

    2.7 sweep/trigger/gate 2-309 2 sc pi d ev ice m es sa ge d et ail s parameter video bandwidth (vbw) range/resolution 1 hz to 10 mhz (1 to 3 sequences), 5 khz, off suffix code none. Value is returned in hz units. Example of use to query the vbw. Swe:egat:view:band:vid? > 3000 [:sense]:sweep:egate:vie...

  • Page 320

    Chapter 2 scpi device message details 2-310 [:sense]:sweep:egate:view:detector[:function]? Gate view detection mode query function this command queries the waveform pattern detection mode for gate view. This parameter and the one for setting the waveform pattern detection mode for time axis measurem...

  • Page 321

    2.7 sweep/trigger/gate 2-311 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:view:points gate view trace point function this command sets the number of trace display points for gate view. This parameter and the one for setting the number of trace display points for time axis measurement ...

  • Page 322

    Chapter 2 scpi device message details 2-312 [:sense]:sweep:egate:view:points? Gate view trace point query function this command queries the number of trace display points for gate view. This parameter and the one for setting the number of trace display points for time axis measurement reference the ...

  • Page 324

    Chapter 2 scpi device message details 2-314 [:sense]:sweep:egate:view:frequency gate view frequency function this command sets the center frequency for gate view. Command [:sense]:sweep:egate:view:frequency parameter center frequency range [ms269xa] –100 mhz to 6.05 ghz (ms2690a) –100 mhz to 13.6 gh...

  • Page 325

    2.7 sweep/trigger/gate 2-315 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:view:frequency? Gate view frequency query function this commands queries the center frequency of the gate view. Command [:sense]:sweep:egate:view:frequency? Response parameter center frequency range [ms269xa] –1...

  • Page 326

    Chapter 2 scpi device message details 2-316 [:sense]:sweep:egate:holdoff gate hold function this command sets the time during which gate input is disabled for a set time, from the first gate signal input until the next gate signal input, during gate sweep. Command [:sense]:sweep:egate:holdoff parame...

  • Page 327

    2.7 sweep/trigger/gate 2-317 2 sc pi d ev ice m es sa ge d et ail s [:sense]:sweep:egate:holdoff? Gate hold query function this command queries the time during which gate input is disabled for a set time, from the first gate signal input until the next gate signal input, during gate sweep. Query [:s...

  • Page 329

    2.7 sweep/trigger/gate 2-319 2 sc pi d ev ice m es sa ge d et ail s :initiate:restart restart sweep function this command restarts the sweep. Command :initiate:restart example of use to restart the sweep. Init:rest :abort stop sweep function this command stops the sweep. Command :abort example of us...

  • Page 332

    Chapter 2 scpi device message details 2-322 [:sense]:radio:standard[:select]? Select standard query function this command queries the setting of the communication standard. Query [:sense]:radio:standard[:select]? Response parameter communication standard off off wcdmadn 3gpp w-cdma downlink wcdmaup ...

  • Page 333

    2.8 measure function 2-323 2 sc pi d ev ice m es sa ge d et ail s :configure:sanalyzer measurement off function this command disables currently running measure function. No operation is made if no measure function is running. Command :configure:sanalyzer example of use to disable the currently runni...

  • Page 334

    Chapter 2 scpi device message details 2-324 [:sense]:radio:standard:load [,] load standard parameter function this command selects the measure function parameter. Selectable parameters vary depending on the setting for standard. Command [:sense]:radio:standard:load [,] parameter measure function adj...

  • Page 335

    2.8 measure function 2-325 2 sc pi d ev ice m es sa ge d et ail s when standard is set to w-cdma uplink (channel power measurement) parameter to be set uplink 3gpp w-cdma uplink, mean power measurement mean 3gpp w-cdma uplink, mean power measurement rrcfilter 3gpp w-cdma uplink, rrc filtered power m...

  • Page 336

    Chapter 2 scpi device message details 2-326 when standard is set to w-cdma downlink (obw measurement) parameter to be set downlink 3gpp w-cdma downlink when omitted: 3gpp w-cdma downlink when standard is set to w-cdma downlink (channel power measurement) parameter to be set downlink 3gpp w-cdma down...

  • Page 337

    2.8 measure function 2-327 2 sc pi d ev ice m es sa ge d et ail s when standard is set to mobile wimax (spectrum emission mask measurement) parameter to be set 10m 10 mhz bw (channel bandwidth 10 mhz) 5m 5 mhz bw (channel bandwidth 5 mhz) when omitted: 10 mhz bw when standard is set to mobile wimax ...

  • Page 338

    Chapter 2 scpi device message details 2-328 10mbw_utra10mhz 10 mhz bw (utra 10 mhz) 10mbw_eutra10mhz 10 mhz bw (e-utra 10 mhz) 10mbw_adv 10 mhz bw (adv mode) 15mbw_utra1m6hz 15 mhz bw (utra 1.6 mhz) 15mbw_utra5mhz 15 mhz bw (utra 5 mhz) 15mbw_utra10mhz 15 mhz bw (utra 10 mhz) 15mbw_eutra15mhz 15 mhz...

  • Page 339

    2.8 measure function 2-329 2 sc pi d ev ice m es sa ge d et ail s when standard is set to lte uplink/downlink, and lte tdd uplink/downlink (channel power measurement) parameter to be set mean_1m4bw mean power 1.4 mhz bw mean_3mbw mean power 3 mhz bw mean_5mbw mean power 5 mhz bw mean_10mbw mean powe...

  • Page 340

    Chapter 2 scpi device message details 2-330 when standard is set to lte downlink (spectrum emission mask measurement) parameter to be set a_under1g_1m4bw categorya a_under1g_3mbw categorya a_under1g_5mbw categorya a_under1g_10mbw categorya a_under1g_15mbw categorya a_under1g_20mbw categorya a_over1g...

  • Page 341

    2.8 measure function 2-331 2 sc pi d ev ice m es sa ge d et ail s g_20m general 20mhz ns3_1_4m ns-03 1.4mhz ns3_3m ns-03 3mhz ns3_5m ns-03 5mhz ns3_10m ns-03 10mhz ns3_15m ns-03 15mhz ns3_20m ns-03 20mhz ns4_1_4m ns-04 1.4mhz ns4_3m ns-04 3mhz ns4_5m ns-04 5mhz ns4_10m ns-04 10mhz ns4_15m ns-04 15mh...

  • Page 342

    Chapter 2 scpi device message details 2-332 ns6_1_4m ns-06/07 1.4mhz ns6_3m ns-06/07 3mhz ns6_5m ns-06/07 5mhz ns6_10m ns-06/07 10mhz when omitted: general 5mhz when standard is set to etc_dsrc (applies to all but burst average power, spectrum emission mask measurement) parameter to be set pi4dqpsk ...

  • Page 343

    2.8 measure function 2-333 2 sc pi d ev ice m es sa ge d et ail s dlt34 dl trace point tune 34 dbm ≤ p dlt26 dl trace point tune 26 dbm ≤ p dlt26u dl trace point tune p ult53 ul trace point tune –53.5 dbm ≤ p ult55 ul trace point tune –55 dbm ≤ p dl34 downlink actual 34 dbm ≤ p dl26 downlink actual ...

  • Page 344

    Chapter 2 scpi device message details 2-334 when standard is set to cdma2000 forward link (spectrum emission mask measurement) parameter to be set bc0_plt28 band class 0,2,5,7,9,10 (pout bc0_plt33 band class 0,2,5,7,9,10 (28 dbm ≤ pout dbm) bc0_pgt33 band class 0,2,5,7,9,10 (pout ≥ 33 dbm) bc1_plt28...

  • Page 345

    2.8 measure function 2-335 2 sc pi d ev ice m es sa ge d et ail s when standard is set to isdb-tmm (spectrum emission mask measurement) parameter to be set 14m2bw 14.2 mhz bw 14m2bw_abs 14.2 mhz bw (abs) 5m6bw 5.6 mhz bw when omitted: 14.2 mhz bw when standard is set to isdb-t sb (channel power meas...

  • Page 346

    Chapter 2 scpi device message details 2-336 communication system sweep band 18 mhz t403_19mspan telec t-403 5 ghz low power data communication system sweep band 19 mhz t403_38mspan telec t-403 5 ghz low power data communication system sweep band 38 mhz t403_78mspan telec t-403 5 ghz low power data c...

  • Page 347

    2.8 measure function 2-337 2 sc pi d ev ice m es sa ge d et ail s spread spectrum system when standard is set to wlan (spectrum emission mask measurement) parameter to be set w11a ieee802.11a w11b ieee802.11b w11gofdm ieee802.11g ofdm w11gdcck ieee802.11g dsss/cck w11gdofdm ieee802.11g dsss-ofdm w11...

  • Page 348

    Chapter 2 scpi device message details 2-338 obw less than 18 mhz t403_18mhz_5260_5320mhz_lower telec t-403 5 ghz low power data communication system 5180 to 5240 mhz lower sideband, obw less than 18 mhz t403_18mhz_5260_5320mhz_upper telec t-403 5 ghz low power data communication system 5260 to 5320 ...

  • Page 349

    2.8 measure function 2-339 2 sc pi d ev ice m es sa ge d et ail s t403_5270_5310mhz_upper telec t-403 5 ghz low power data communication system 5270 to 5310 mhz upper sideband t403_5210mhz_lower telec t-403 5 ghz low power data communication system 5210 mhz lower sideband t403_5210mhz_upper telec t-...

  • Page 350

    Chapter 2 scpi device message details 2-340 t403_5290mhz_80-80_lower telec t-403 5 ghz low power data communication system 5290 mhz 80+80 mhz lower sideband t403_5290mhz_80-80_upper telec t-403 5 ghz low power data communication system 5290 mhz 80+80 mhz upper sideband t403_5290_5530mhz_lower telec ...

  • Page 351

    2.8 measure function 2-341 2 sc pi d ev ice m es sa ge d et ail s t403_18_19mhz_5_6ghz telec t-403 5 ghz low power data communication system 5.6 ghz obw more than 18 mhz, less than 19 mhz t403_19mhz_5_2ghz telec t-403 5 ghz low power data communication system 5.2 ghz obw more than 19 mhz t403_19mhz_...

  • Page 352

    Chapter 2 scpi device message details 2-342 t403_5530_5610m telec t-403 5 ghz low power data communication system, 5530 to 5610 mhz t403_5570m telec t-403 5 ghz low power data communication system, 5570 mhz t405_5mhz_4_9ghz telec t-405 5 ghz wireless access system 5 mhz system 4,900 mhz to 4,950 mhz...

  • Page 353

    2.8 measure function 2-343 2 sc pi d ev ice m es sa ge d et ail s fcc_15_407_5_25ghz_devices fcc part 15.407 5.25-5.35 ghz band devices fcc_15_407_5_47ghz fcc part 15.407 5.47-5.725 ghz band fcc_15_407_5_725ghz fcc part 15.407 5.725-5.825 ghz band etsi_301_893 en 301 893 4.5.1 transmitter unwanted e...

  • Page 354

    Chapter 2 scpi device message details 2-344 when standard is set to apco p25 (acp measurement) parameter to be set except_700mhz-band except 700mhz-band 700mhz-bw-6_25khz 700mhz-bw-6.25khz 700mhz-bw-25khz 700mhz-bw-25khz 700mhz-bw-100khz 700mhz-bw-100khz when omitted: except 700mhz-band when standar...

  • Page 355

    2.8 measure function 2-345 2 sc pi d ev ice m es sa ge d et ail s frequency band:above30ghz 28m2 cs:7mhz class:2 28m4l3-17g cs:7mhz class:4l frequency band:3g-17ghz 28m4l17-30g cs:7mhz class:4l frequency band:17g-30ghz 28m4labv30g cs:7mhz class:4l frequency band:above30ghz 28m4h3-17g cs:7mhz class:4...

  • Page 356

    Chapter 2 scpi device message details 2-346 when omitted: cs:7mhz class:2 when standard is set to nxdn (acp measurement) parameter to be set bw-6_25khz bw-6.25khz bw-12_5khz bw-12.5khz when omitted: bw-12.5khz when standard is set to nxdn (spectrum emission mask measurement) parameter to be set 47cf...

  • Page 357

    2.8 measure function 2-347 2 sc pi d ev ice m es sa ge d et ail s [:sense]:radio:standard:load? Load standard parameter query function this command queries the measure function parameter. The parameter selected for the standard setting differs. Query [:sense]:radio:standard:load? Response parameter ...

  • Page 360

    Chapter 2 scpi device message details 2-350 table 2.9-1 device messages for adjacent channel power measurement (cont’d) function device message adjacent channel power offset frequency - advanced mode [:sense]:acpower:advanced:offset:list[:frequency] ,,,,,,, [:sense]:acpower:advanced:offset:list[:fre...

  • Page 361

    2.9 acp 2-351 2 sc pi d ev ice m es sa ge d et ail s table 2.9-1 device messages for adjacent channel power measurement (cont’d) function device message adjacent channel power read :read:acp[n]? Adjacent channel power measure :measure:acp[n]? All marker off :calculate:acpower:marker:aoff peak search...

  • Page 364

    Chapter 2 scpi device message details 2-354 [:sense]:acpower[:state]? Measure adjacent channel power query function this command queries the on/off state of the adjacent channel power measurement. Query [:sense]:acpower[:state]? Response parameter acp measurement on/off 1 on 0 off example of use to ...

  • Page 365

    2.9 acp 2-355 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:carrier[1]:rcarrier adjacent channel power reference carrier select function this command sets the reference carrier number for adjacent channel power measurement. Command [:sense]:acpower:carrier[1]:rcarrier parameter reference c...

  • Page 366

    Chapter 2 scpi device message details 2-356 [:sense]:acpower:carrier[1]:rcarrier? Adjacent channel power reference carrier select query function this command queries the reference carrier number for adjacent channel power measurement. Query [:sense]:acpower:carrier[1]:rcarrier? Response parameter re...

  • Page 369

    2.9 acp 2-359 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:carrier[1]:rcarrier:method? Adjacent channel power reference query function this command queries the reference of the relative level display for adjacent channel power measurement. Query [:sense]:acpower:carrier[1]:rcarrier:method...

  • Page 370

    Chapter 2 scpi device message details 2-360 :calculate:acpower:carrier[1]:rcarrier:method? Adjacent channel power reference query function this command queries the reference of the relative level display for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:rcarrier:method?. R...

  • Page 373

    2.9 acp 2-363 2 sc pi d ev ice m es sa ge d et ail s example of use to query the noise canceling function on/off state. Acp:corr:nois? > 0 related command this command has the same function as the following command. :calculate:acpower:correction:noise[:auto]? :calculate:acpower:correction:noise[:aut...

  • Page 374

    Chapter 2 scpi device message details 2-364 example of use to set the offset channel bandwidth to 3.84 mhz. Acp:offs:band 3.84mhz related command this command has the same function as the following command. :calculate:acpower:offset[1]:bandwidth[:integration] :calculate:acpower:offset[1]:bandwidth[:...

  • Page 375

    2.9 acp 2-365 2 sc pi d ev ice m es sa ge d et ail s example of use to query the offset channel bandwidth. Acp:offs:band? > 3840000 related command this command has the same function as the following command. :calculate:acpower:offset[1]:bandwidth[:integration]? :calculate:acpower:offset[1]:bandwidt...

  • Page 376

    Chapter 2 scpi device message details 2-366 example of use to set the inband channel bandwidth to 3.84 mhz. Acp:carr:band 3.84mhz related command this command has the same function as the following command. :calculate:acpower:carrier[1]:list:bandwidth[:integratio n] :calculate:acpower:carrier[1]:lis...

  • Page 377

    2.9 acp 2-367 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:carrier[1]:list:bandwidth[:integration]? Adjacent channel power carrier bandwidth query function this command sets the measurement bandwidth of the carrier for adjacent channel power measurement. Query [:sense]:acpower:carrier[1]:...

  • Page 378

    Chapter 2 scpi device message details 2-368 :calculate:acpower:carrier[1]:list:bandwidth[:integration]? Adjacent channel power carrier bandwidth query function this command sets the measurement bandwidth of the carrier for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:list...

  • Page 379

    2.9 acp 2-369 2 sc pi d ev ice m es sa ge d et ail s :calculate:acpower:carrier[1]:rcfrequency adjacent channel power in band center function this command sets the in band center frequency for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:rcfrequency. Related command this ...

  • Page 380

    Chapter 2 scpi device message details 2-370 :calculate:acpower:carrier[1]:rcfrequency? Adjacent channel power in band center query function this command queries the in band center frequency for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:rcfrequency?. Related command thi...

  • Page 381

    2.9 acp 2-371 2 sc pi d ev ice m es sa ge d et ail s :calculate: acpower:carrier[1]:count adjacent channel power carrier number function this command sets the carrier number for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:count. Related command this command has the same ...

  • Page 382

    Chapter 2 scpi device message details 2-372 related command this command has the same function as the following command. :calculate:acpower:carrier[1]:count? :calculate:acpower:carrier[1]:count? Adjacent channel power carrier number query function this command queries the carrier number for adjacent...

  • Page 383

    2.9 acp 2-373 2 sc pi d ev ice m es sa ge d et ail s example of use to set the frequency interval among carriers to 12.3 mhz. Acp:carr:widt 12300000 related command this command has the same function as the following command. :calculate:acpower:carrier[1]:list:width :calculate:acpower:carrier[1]:lis...

  • Page 384

    Chapter 2 scpi device message details 2-374 details this command is available when acp reference is set to the following: • span total example of use to query the frequency interval among carriers. Acp:carr:widt? > 12300000 related command this command has the same function as the following command....

  • Page 386

    Chapter 2 scpi device message details 2-376 [:sense]:acpower:offset[1]:list:state? Adjacent channel power offset query function this command queries the on/off state of the offset channel for adjacent channel power measurement. Query [:sense]:acpower:offset[1]:list:state? Response ,, parameter measu...

  • Page 387

    2.9 acp 2-377 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:offset[1]:list[:frequency] ,, adjacent channel power offset frequency function this command sets the offset frequency of offset channel for adjacent channel power measurement. Command [:sense]:acpower:offset[1]:list[:frequency] ,,...

  • Page 388

    Chapter 2 scpi device message details 2-378 [:sense]:acpower:offset[1]:list[:frequency]? Adjacent channel power offset frequency query function this command queries the offset frequency of offset channel for adjacent channel power measurement. Query [:sense]:acpower:offset[1]:list[:frequency]? Respo...

  • Page 392

    Chapter 2 scpi device message details 2-382 [:sense]:acpower:carrier[1]:filter:type? Adjacent channel power filter type query function this command queries the filter type of the carrier for adjacent channel power measurement. Command [:sense]:acpower:carrier[1]:filter:type response parameter filter...

  • Page 394

    Chapter 2 scpi device message details 2-384 [:sense]:acpower:filter[:rrc][:state]? Adjacent channel power offset filter type query function this command queries the filter type of the offset channel for adjacent channel power measurement. Query [:sense]:acpower:filter[:rrc][:state]? Response paramet...

  • Page 396

    Chapter 2 scpi device message details 2-386 [:sense]:acpower:offset[1]:filter:type? Adjacent channel power offset filter type query function this command queries filter type of the offset for adjacent channel power measurement. Query [:sense]:acpower:offset[1]:filter:type? Response parameter filter ...

  • Page 398

    Chapter 2 scpi device message details 2-388 [:sense]:acpower:advanced:offset:mode? Adjacent channel power offset mode query function this command queries offset mode for acp measurement. Query [:sense]:acpower:advanced:offset:mode? Response parameter offset mode norm normal setting adv advanced sett...

  • Page 399

    2.9 acp 2-389 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:advanced:offset:bandwidth[:integration] ,,,,,th>,, adjacent channel power offset channel bandwidth function this command sets offset channel bandwidth for adjacent channel power measurement. Command :sense]:acpower:advanced:offset...

  • Page 400

    Chapter 2 scpi device message details 2-390 [:sense]:acpower:advanced:offset:bandwidth[:integration]? Adjacent channel power offset channel bandwidth query function this command queries offset channel bandwidth for adjacent channel power measurement. Query [:sense]:acpower:advanced:offset:bandwidth[...

  • Page 402

    Chapter 2 scpi device message details 2-392 [:sense]:acpower:advanced:offset:list:state? Adjacent channel power offset query function this command queries the on/off status of the offset channel for adjacent channel power measurement. Query [:sense]:acpower:advanced:offset:list:state? Response ,,,,,...

  • Page 403

    2.9 acp 2-393 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:advanced:offset:list[:frequency] ,,,,,,, adjacent channel power offset frequency function this command sets the offset channel frequency for adjacent channel power measurement. Command [:sense]:acpower:advanced:offset:list[:freque...

  • Page 404

    Chapter 2 scpi device message details 2-394 [:sense]:acpower:advanced:offset:list[:frequency]? Adjacent channel power offset frequency query function this command queries the offset frequency of the offset channel for adjacent channel power measurement. Query [:sense]:acpower:advanced:offset:list[:f...

  • Page 406

    Chapter 2 scpi device message details 2-396 [:sense]:acpower:advanced:offset:filter:type? Adjacent channel power offset filter type query function this command queries the offset filter for acp measurement. Query [:sense]:acpower:advanced:offset:filter:type? Response ,,,,,,ode_7>, parameter filter t...

  • Page 407

    2.9 acp 2-397 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:advanced:filter[:rrc]:alpha adjacent channel power offset rolloff ratio function this command sets the roll-off rate of the adjacent channel power measurement offset channel filter. Command [:sense]:acpower:advanced:filter[:rrc]:a...

  • Page 408

    Chapter 2 scpi device message details 2-398 [:sense]:acpower:advanced:filter[:rrc]:alpha? Adjacent channel power offset rolloff ratio query function this command queries the roll-off rate of the adjacent channel power measurement offset channel filter. Command [:sense]:acpower:advanced:filter[:rrc]:...

  • Page 410

    Chapter 2 scpi device message details 2-400 :display:acpower:result:type? Adjacent channel power result type query function this command queries the type of the result display for adjacent channel power measurement. Command :display:acpower:result:type? Response parameter result display type carr se...

  • Page 411

    2.9 acp 2-401 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:carrier[1]:list:filter:alpha adjacent channel power rolloff ratio function this command sets the rolloff ratio of the filter of the reference channel for adjacent channel power measurement. Command [:sense]:acpower:carrier[1]:list...

  • Page 412

    Chapter 2 scpi device message details 2-402 :calculate:acpower:carrier[1]:list:filter:alpha adjacent channel power rolloff ratio function this command sets the rolloff ratio of the filter of the reference channel for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:list:filte...

  • Page 413

    2.9 acp 2-403 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:carrier[1]:list:filter:alpha? Adjacent channel power rolloff ratio query function this command sets the rolloff ratio of the filter of the reference channel for adjacent channel power measurement. Query [:sense]:acpower:carrier[1]...

  • Page 414

    Chapter 2 scpi device message details 2-404 :calculate:acpower:carrier[1]:list:filter:alpha? Adjacent channel power rolloff ratio query function this command sets the rolloff ratio of the filter of the reference channel for adjacent channel power measurement. Refer to [:sense]:acpower:carrier[1]:lis...

  • Page 415

    2.9 acp 2-405 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:filter[:rrc]:alpha adjacent channel power offset rolloff ratio function this command sets the rolloff ratio of the filter of the offset channel for adjacent channel power measurement. Command [:sense]:acpower:filter[:rrc]:alpha pa...

  • Page 416

    Chapter 2 scpi device message details 2-406 [:sense]:acpower:filter[:rrc]:alpha? Adjacent channel power offset rolloff ratio query function this command sets the rolloff ratio of the filter of the offset channel for adjacent channel power measurement. Command [:sense]:acpower:filter[:rrc]:alpha? Res...

  • Page 417

    2.9 acp 2-407 2 sc pi d ev ice m es sa ge d et ail s :calculate:acpower:filter[:rrc]:alpha? Adjacent channel power offset rolloff ratio query function this command queries the rolloff ratio of the filter of the offset channel for adjacent channel power measurement. Refer to [:sense]:acpower:filter[:...

  • Page 418

    Chapter 2 scpi device message details 2-408 :initiate:acp adjacent channel power initiate function this command starts adjacent channel power measurement. Command :initiate:acp details acp measurement is set to on and the measurement starts, when this function is executed. To read out the measuremen...

  • Page 419

    2.9 acp 2-409 2 sc pi d ev ice m es sa ge d et ail s :fetch:acp[n]? Adjacent channel power read fetch function this command outputs the measurement result for adjacent channel power measurement. Query :fetch:acp[n]? Response when the result mode is “a”: when offset setup mode is normal when acp meas...

  • Page 420

    Chapter 2 scpi device message details 2-410 when offset setup mode is advanced in acp measurement (when acp result type is offset) two values of ref_carrier_a are output when acp reference is bsides. (,), ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, , (n=1 or when omitted) in acp measurement (when a...

  • Page 421

    2.9 acp 2-411 2 sc pi d ev ice m es sa ge d et ail s in acp measurement (when acp result type is all) two values of ref_carrier_a are output when acp reference is bsides. ,, ,,,, ,,,, ,,,, (,), ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, , (n=1 or when omitted) when the result mode is “b”. When off...

  • Page 422

    Chapter 2 scpi device message details 2-412 ,, ,, ,, ,, , (n = 1 or when omitted, and when acp reference is both sides of carriers) ,, ,, ...... ,, ,, ,, ,, ,, ,, , (in n=2) when offset setup mode is advanced when carrier number = 1 and only offset-1 = on ,, other than the above 0.0,,0.0,, ,, ,, ,, ...

  • Page 423

    2.9 acp 2-413 2 sc pi d ev ice m es sa ge d et ail s 0.0,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, , (n=1 or when omitted, and when acp reference is both sides of carriers) ,, ,, ...... ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, ,, , (n=2).

  • Page 424

    Chapter 2 scpi device message details 2-414 parameter relative power of the lower offset-n relative power of the upper offset-n no suffix code, db units, 0.01 db resolution –999.0 is returned when an error occurs/no measurement is performed. Power of the reference carrier power of the carrier on the...

  • Page 425

    2.9 acp 2-415 2 sc pi d ev ice m es sa ge d et ail s :read:acp[n]? Adjacent channel power read function this command performs the adjacent channel power measurement and outputs the measurement result. It achieves the same result as when commands are sent in the order of :initiate:acp :*wai :fetch:ac...

  • Page 433

    2.9 acp 2-423 2 sc pi d ev ice m es sa ge d et ail s :display:acpower:annotation:title:data? Title entry query function this command queries the title character string. Refer to :display:annotation:title:data?. Related command this command has the same function as the following commands. :display:an...

  • Page 434

    Chapter 2 scpi device message details 2-424 :display:acpower:view[1]:window[1]:trace:y[:scale]:pdivision? Log scale range query function this command queries the y-axis scale magnification when scale mode is set to log. Refer to :display:window[1]:trace:y[:scale]:[logarithmic]:pdivisi on?. Related c...

  • Page 435

    2.9 acp 2-425 2 sc pi d ev ice m es sa ge d et ail s :display:acpower:view[1]:window[1]:trace:y[:scale]:rlevel reference level function this command sets the reference level. Refer to :display:window[1]:trace:y[:scale]:rlevel. Related command this command has the same function as the following comma...

  • Page 437

    2.9 acp 2-427 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:average:count average count function this command sets the storage count. Refer to [:sense]:average:count. Related command this command has the same function as the following commands. [:sense]:average:count [:sense]:chpower:avera...

  • Page 448

    Chapter 2 scpi device message details 2-438 [:sense]:acpower:detector[:function]? Detection mode query function this command queries the detection mode for the waveform pattern. Refer to [:sense]:detector[:function]?. Related command this command has the same function as the following commands. [:se...

  • Page 449

    2.9 acp 2-439 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:frequency:span span frequency function this command sets the span frequency. Refer to [:sense]:frequency:span. Related command this command has the same function as the following commands. [:sense]:frequency:span [:sense]:chpower:...

  • Page 450

    Chapter 2 scpi device message details 2-440 [:sense]:acpower:sweep:points trace point function this command sets the number of the trace display points. Refer to [:sense]:sweep:points. Related command this command has the same function as the following commands. [:sense]:sweep:points [:sense]:chpowe...

  • Page 451

    2.9 acp 2-441 2 sc pi d ev ice m es sa ge d et ail s [:sense]:acpower:sweep:time sweep time function this command sets the sweep time. Refer to [:sense]:sweep:time. Related command this command has the same function as the following commands. [:sense]:sweep:time [:sense]:chpower:sweep:time [:sense]:...

  • Page 467

    2.10 burst average power 2-457 2 sc pi d ev ice m es sa ge d et ail s details this function outputs the measurement result of the burst average power measurement last performed. It outputs the measurement result in a state that the measurement has already been done, or in a different style. You can ...

  • Page 491

    2.11 channel power 2-481 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower[:state]? Measure channel power query function this command queries the on/off state of the channel power measurement. Command [:sense]:chpower[:state]? Parameter chp measurement on/off 1 on 0 off example of use to query...

  • Page 492

    Chapter 2 scpi device message details 2-482 [:sense]:chpower:frequency:center channel power channel center frequency function this command sets the center frequency for channel power measurement. Command [:sense]:chpower:frequency:center parameter channel center frequency range (start frequency) to ...

  • Page 493

    2.11 channel power 2-483 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:frequency:center? Channel power channel center frequency query function this command queries the center frequency for channel power measurement. Query [:sense]:chpower:frequency:center? Response parameter center frequen...

  • Page 494

    Chapter 2 scpi device message details 2-484 [:sense]:chpower:bandwidth:integration channel power channel bandwidth function this command sets the channel bandwidth for channel power measurement. Command [:sense]:chpower:bandwidth:integration parameter channel bandwidth range 1 hz to 2.5 ghz resoluti...

  • Page 495

    2.11 channel power 2-485 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:bandwidth:integration? Channel power channel bandwidth query function this command queries the channel bandwidth for channel power measurement. Query [:sense]:chpower:bandwidth:integration? Response parameter channel ba...

  • Page 497

    2.11 channel power 2-487 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:filter:type? Channel power filter type query function this command queries filter type for channel power measurement. Query [:sense]:chpower:filter:type? Response parameter filter type rect rectangle filter nyq nyquist ...

  • Page 499

    2.11 channel power 2-489 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:filter[:rrc][:state]? Channel power filter type query function this command queries filter type for channel power measurement. Query [:sense]:chpower:filter[:rrc][:state]? Response parameter filter type 0 rectangle filt...

  • Page 500

    Chapter 2 scpi device message details 2-490 [:sense]:chpower:filter[:rrc]:alpha channel power rolloff ratio function this command sets filter rolloff ratio for channel power measurement. Command [:sense]:chpower:filter[:rrc]:alpha parameter rolloff ratio range 0.01 to 1.00 resolution 0.01 suffix cod...

  • Page 501

    2.11 channel power 2-491 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:filter[:rrc]:alpha? Channel power rolloff ratio query function this command queries the rolloff ratio for channel power measurement. Query [:sense]:chpower:filter[:rrc]:alpha? Response parameter filter rolloff ratio ran...

  • Page 502

    Chapter 2 scpi device message details 2-492 :calculate:chpower:filter[:rrc]:alpha? Channel power rolloff ratio query function this command queries the rolloff ratio for channel power measurement. Refer to [:sense]:chpower:filter[:rrc]:alpha?. Related command this command has the same function as the...

  • Page 503

    2.11 channel power 2-493 2 sc pi d ev ice m es sa ge d et ail s :initiate:chpower channel power initiate function this command starts channel power measurement. Command :initiate:chpower details channel power measurement is set to on and the measurement starts, when this function is executed. To rea...

  • Page 504

    Chapter 2 scpi device message details 2-494 :fetch:chpower[n]? Channel power fetch function this command queries the measurement result for channel power measurement. Query :fetch:chpower[n]? Response when the result mode is “a”. , (n=1 or when omitted) when the result mode is “b”. , (n=1 or when om...

  • Page 505

    2.11 channel power 2-495 2 sc pi d ev ice m es sa ge d et ail s details this function outputs the measurement result at the channel power measurement last performed. It is possible to output the measurement result in a state that the measurement has already been done, and in a different style. You c...

  • Page 506

    Chapter 2 scpi device message details 2-496 :fetch:chpower:chpower? Channel power fetch function this command queries the total in band power for channel power measurement. Query :fetch:chpower:chpower? Response parameter total in band power specified in channel bandwidth. This command returns a val...

  • Page 507

    2.11 channel power 2-497 2 sc pi d ev ice m es sa ge d et ail s :fetch:chpower:density? Channel power fetch function this command queries the total in band power density for channel power measurement. Query :fetch:chpower:density? Response parameter in band power density specified in channel bandwid...

  • Page 508

    Chapter 2 scpi device message details 2-498 :read:chpower[n]? Channel power read function this command performs the measurement for channel power and outputs the measurement result. It achieves the same result as when commands are sent in the order of :initiate:chpower :fetch:chpower[n]? :read:chpow...

  • Page 509

    2.11 channel power 2-499 2 sc pi d ev ice m es sa ge d et ail s :measure:chpower:chpower? Channel power measure function this command performs the measurement for channel power and outputs the total in band power. It achieves the same result as when commands are sent in the order of :configure:chpow...

  • Page 516

    Chapter 2 scpi device message details 2-506 :display:chpower:annotation:title:data? Title entry query function this command queries the title character string. Refer to :display:annotation:title:data?. Command this command has the same function as the following commands. :display:annotation:title:da...

  • Page 517

    2.11 channel power 2-507 2 sc pi d ev ice m es sa ge d et ail s :display:chpower:view[1]:window[1]:trace:y[:scale]:pdivision? Log scale range query function this command queries the y axis scale magnification when scale mode is set to log. Refer to :display:window[1]:trace:y[:scale]:[logarithmic]:pd...

  • Page 518

    Chapter 2 scpi device message details 2-508 :display:chpower:view[1]:window[1]:trace:y[:scale]:rlevel reference level function this command sets the reference level. Refer to :display:window[1]:trace:y[:scale]:rlevel. Related command this command has the same function as the following commands. :dis...

  • Page 520

    Chapter 2 scpi device message details 2-510 [:sense]:chpower:average:count average count function this command sets the storage count. Refer to [:sense]:average:count. Related command this command has the same function as the following commands. [:sense]:average:count [:sense]:acpower:average:count ...

  • Page 531

    2.11 channel power 2-521 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:detector[:function]? Detection mode query function this command queries the detection mode of the waveform pattern. Refer to [:sense]:detector[:function]?. Related command this command has the same function as the follo...

  • Page 532

    Chapter 2 scpi device message details 2-522 [:sense]:chpower:frequency:span span frequency function this command sets the span frequency. Refer to [:sense]:frequency:span. Related command this command has the same function as the following commands. [:sense]:frequency:span [:sense]:acpower:frequency...

  • Page 533

    2.11 channel power 2-523 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:sweep:points trace point function this command sets the number of the trace display points. Refer to [:sense]:sweep:points. Related command this command has the same function as the following commands. [:sense]:sweep:po...

  • Page 534

    Chapter 2 scpi device message details 2-524 [:sense]:chpower:sweep:time? Sweep time query function this command queries the sweep time. Refer to [:sense]:sweep:time?. Related command this command has the same function as the following commands. [:sense]:sweep:time? [:sense]:acpower:sweep:time? [:sen...

  • Page 535

    2.11 channel power 2-525 2 sc pi d ev ice m es sa ge d et ail s [:sense]:chpower:sweep:time:auto? Sweep time auto/manual query function this command queries the on/off state of the automatic sweep time setting. Refer to [:sense]:sweep:time:auto?. Related command this command has the same function as...

  • Page 539

    2.12 obw 2-529 2 sc pi d ev ice m es sa ge d et ail s table 2.12-1 device messages for occupied bandwidth measurement (cont’d) function device message video bandwidth [:sense]:obwidth:bandwidth:video [:sense]:obwidth:bandwidth:video? Video bandwidth auto/manual [:sense]:obwidth:bandwidth:video:auto ...

  • Page 544

    Chapter 2 scpi device message details 2-534 [:sense]:obwidth:percent obw n% ratio function this command sets the occupied frequency bandwidth (n% method) condition. Command [:sense]:obwidth:percent parameter n% range 0.01 to 99.99 % resolution 0.01 suffix code none default 99.00% example of use to s...

  • Page 545

    2.12 obw 2-535 2 sc pi d ev ice m es sa ge d et ail s [:sense]:obwidth:percent? Obw n% ratio query function this command queries the occupied frequency bandwidth (n% method) condition. Query [:sense]:obwidth:percent? Response parameter n% range 0.01 to 99.99 % resolution 0.01 suffix code none. Value...

  • Page 546

    Chapter 2 scpi device message details 2-536 :calculate:obwidth:percent obw n% ratio function this command sets the occupied frequency bandwidth (n% method) condition. Refer to [:sense]:obwidth:percent. Related command this command has the same function as the following command. [:sense]:obwidth:perc...

  • Page 547

    2.12 obw 2-537 2 sc pi d ev ice m es sa ge d et ail s [:sense]:obwidth:xdb obw x db value function this command sets the occupied frequency bandwidth (x db) condition. Command [:sense]:obwidth:xdb parameter x db range 0.01 to 100.00 db resolution 0.01 db suffix code db db is used even when omitted. ...

  • Page 548

    Chapter 2 scpi device message details 2-538 [:sense]:obwidth:xdb? Obw x db value query function this command queries the occupied frequency bandwidth (x db) condition. Query [:sense]:obwidth:xdb? Response parameter x db range 0.01 to 100.00 db resolution 0.01 db suffix code none. Value is returned i...

  • Page 549

    2.12 obw 2-539 2 sc pi d ev ice m es sa ge d et ail s :calculate:obwidth:xdb obw x db value function this command sets the occupied frequency bandwidth (x db) condition. Refer to [:sense]:obwidth:xdb. Related command this command has the same function as the following command. [:sense]:obwidth:xdb :...

  • Page 550

    Chapter 2 scpi device message details 2-540 :configure:obwidth occupied bandwidth configure function this command sets obw measurement to on. Command :configure:obwidth details no measurement is performed. Example of use to set obw measurement to on. Conf:obw :initiate:obwidth occupied bandwidth ini...

  • Page 551

    2.12 obw 2-541 2 sc pi d ev ice m es sa ge d et ail s :fetch:obwidth[n]? Occupied bandwidth fetch function this command outputs the measurement result of obw measurement. Query :fetch:obwidth[n]? Response when the result mode is “a”. ,,, (n=1 or when omitted) when the result mode is “b”. ,-999.0,,, ...

  • Page 552

    Chapter 2 scpi device message details 2-542 trace point number suffix code none. “–999.0” is returned when no measurement is executed. Details this function outputs the measurement result of the obw measurement performed last. It is possible to output the measurement result in a state that the measu...

  • Page 553

    2.12 obw 2-543 2 sc pi d ev ice m es sa ge d et ail s :fetch:obwidth:ferror? Occupied bandwidth fetch function this command outputs the difference between the center frequency of occupied bandwidth of obw measurement and the center frequency. Query :fetch:obwidth:ferror? Response parameter differenc...

  • Page 554

    Chapter 2 scpi device message details 2-544 :read:obwidth[n]? Occupied bandwidth read function this command performs the obw measurement and outputs the measurement result. It achieves the same result as when commands are sent in the order of :initiate:obwidth :fetch:obwidth[n]? :read:obwidth:ferror...

  • Page 555

    2.12 obw 2-545 2 sc pi d ev ice m es sa ge d et ail s :measure:obwidth:ferror? Occupied bandwidth measure function this command performs the measurement of obw and outputs the difference between the center frequency of occupied bandwidth and the center frequency. It achieves the same result as when ...

  • Page 562

    Chapter 2 scpi device message details 2-552 :display:obwidth:annotation:title:data title entry function this command registers the title character string. Refer to :display:annotation:title:data. Related command this command has the same function as the following commands. :display:annotation:title:...

  • Page 563

    2.12 obw 2-553 2 sc pi d ev ice m es sa ge d et ail s :display:obwidth:view[1]:window[1]:trace:y[:scale]:pdivision log scale range function this command sets the y-axis scale magnification when scale mode is set to log. Refer to :display:window[1]:trace:y[:scale]:[logarithmic]:pdivisi on. Related co...

  • Page 564

    Chapter 2 scpi device message details 2-554 :display:obwidth:view[1]:window[1]:trace:y[:scale]:pdivision? Log scale range query function this command queries the y-axis scale magnification when scale mode is set to log. Refer to :display:window[1]:trace:y[:scale]:[logarithmic]:pdivisi on?. Related c...

  • Page 565

    2.12 obw 2-555 2 sc pi d ev ice m es sa ge d et ail s :display:obwidth:view[1]:window[1]:trace:y[:scale]:rlevel reference level function this command sets the reference level. Refer to :display:window[1]:trace:y[:scale]:rlevel. Related command this command has the same function as the following comm...

  • Page 567

    2.12 obw 2-557 2 sc pi d ev ice m es sa ge d et ail s [:sense]:obwidth:average:count average count function this command sets the storage count. Refer to [:sense]:average:count. Related command this command has the same function as the following commands. [:sense]:average:count [:sense]:acpower:aver...

  • Page 579

    2.12 obw 2-569 2 sc pi d ev ice m es sa ge d et ail s [:sense]:obwidth:frequency:span span frequency function this command sets the span frequency. Refer to [:sense]:frequency:span. Related command this command has the same function as the following commands. [:sense]:frequency:span [:sense]:acpower...

  • Page 580

    Chapter 2 scpi device message details 2-570 [:sense]:obwidth:sweep:points trace point function this command sets the number of the trace display points. Refer to [:sense]:sweep:points. Related command this command has the same function as the following commands. [:sense]:sweep:points [:sense]:acpowe...

  • Page 581

    2.12 obw 2-571 2 sc pi d ev ice m es sa ge d et ail s [:sense]:obwidth:sweep:time sweep time function this command sets the sweep time. Refer to [:sense]:sweep:time. Related command this command has the same function as the following commands. [:sense]:sweep:time [:sense]:acpower:sweep:time [:sense]...

  • Page 585

    2.13 spectrum emission mask 2-575 2 sc pi d ev ice m es sa ge d et ail s table 2.13-1 device messages for spectrum emission mask measurement (cont’d) function device message spectrum emission mask offset resolution bandwidth [:sense]:semask:offset[1]:list:bandwidth[1][:resolution] [,[,[,[,idth_5>[,[...

  • Page 586

    Chapter 2 scpi device message details 2-576 table 2.13-1 device messages for spectrum emission mask measurement (cont’d) function device message spectrum emission mask sweep time [:sense]:semask:sweep[1]:time [:sense]:semask:sweep[1]:time? Spectrum emission mask offset sweep time [:sense]:semask:off...

  • Page 589

    2.13 spectrum emission mask 2-579 2 sc pi d ev ice m es sa ge d et ail s table 2.13-1 device messages for spectrum emission mask measurement (cont’d) function device message spectrum emission mask fail logic [:sense]:semask:logic:offset[1]:list:test [,[,[,[,[,[ ,[,[,[,[,[,12>]]]]]]]]]]] [:sense]:sem...

  • Page 590

    Chapter 2 scpi device message details 2-580 table 2.13-1 device messages for spectrum emission mask measurement (cont’d) function device message spectrum emission mask sweep type select rules real fft width query [:sense]:semask:sweep[1][:type][:auto]:rules:fft:rwidth? Spectrum emission mask offset ...

  • Page 593

    2.13 spectrum emission mask 2-583 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:side? Spectrum emission mask limit side query function this command queries the judgment target area for the spectrum emission mask measurement. Query [:sense]:semask:offset[1]:side? Response parameter...

  • Page 595

    2.13 spectrum emission mask 2-585 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:type? Spectrum emission mask reference type query function this command queries the reference power type for spectrum emission mask measurement. Query [:sense]:semask:type? Response parameter type of reference t...

  • Page 597

    2.13 spectrum emission mask 2-587 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:type? Spectrum emission mask reference type query function this command queries the reference power type for spectrum emission mask measurement. Query :calculate:semask:type? Response parameter type of referen...

  • Page 598

    Chapter 2 scpi device message details 2-588 [:sense]:semask:carrier[:power] spectrum emission mask reference power function this command sets the reference power for spectrum emission mask measurement. Command [:sense]:semask:carrier[:power] parameter reference power range –200 to 200 dbm resolution...

  • Page 599

    2.13 spectrum emission mask 2-589 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:carrier[:power]? Spectrum emission mask reference power query function this command queries the reference power for spectrum emission mask measurement. Query [:sense]:semask:carrier[:power]? Response parameter r...

  • Page 600

    Chapter 2 scpi device message details 2-590 :calculate:semask:carrier[:power] spectrum emission mask reference power function this command sets the reference power for spectrum emission mask measurement. Command :calculate:semask:carrier[:power] parameter reference power range –200 to 200 dbm resolu...

  • Page 601

    2.13 spectrum emission mask 2-591 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:carrier[:power]? Spectrum emission mask reference power query function this command queries the reference power for spectrum emission mask measurement. Query :calculate:semask:carrier[:power]? Response paramet...

  • Page 605

    2.13 spectrum emission mask 2-595 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:attenuation? Spectrum emission mask attenuator query function this command queries the attenuation when measuring the reference power for spectrum emission mask measurement. Command [:sense]:semask:attenuation? ...

  • Page 607

    2.13 spectrum emission mask 2-597 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:attenuation? Spectrum emission mask offset attenuator query function this command sets the attenuation when measuring the offset for spectrum emission mask measurement. Query [:sense]:semask:offse...

  • Page 608

    Chapter 2 scpi device message details 2-598 [:sense]:semask:bandwidth[1][:resolution] spectrum emission mask resolution bandwidth function this command sets the resolution bandwidth (rbw) of the reference channel for spectrum emission mask measurement. Command [:sense]:semask:bandwidth[1][:resolutio...

  • Page 609

    2.13 spectrum emission mask 2-599 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:bandwidth[1][:resolution]? Spectrum emission mask resolution bandwidth query function this command queries the resolution bandwidth (rbw) of the reference channel for spectrum emission mask measurement. Query [:...

  • Page 611

    2.13 spectrum emission mask 2-601 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:bandwidth[1][:resolution]:auto? Spectrum emission mask resolution bandwidth auto/manual query function this command queries the on/off state of the automatic resolution bandwidth (rbw) setting function for the r...

  • Page 612

    Chapter 2 scpi device message details 2-602 [:sense]:semask:offset[1]:list:bandwidth[1][:resolution] [,[,[,[,h_5>[,[,[,[,[,ndwidth_10>[,[,]]]]]]]]]]] spectrum emission mask offset resolution bandwidth function this command sets the resolution bandwidth (rbw) of the offset for spectrum emission mask ...

  • Page 613

    2.13 spectrum emission mask 2-603 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1][:resolution]? Spectrum emission mask offset resolution bandwidth query function this command queries the resolution bandwidth (rbw) of the offset for spectrum emission mask measuremen...

  • Page 614

    Chapter 2 scpi device message details 2-604 [:sense]:semask:offset[1]:list:bandwidth[1][:resolution]:auto [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset resolution bandwidth auto/manual function this command enables/disables the automatic resolution bandwidth (rbw) settin...

  • Page 615

    2.13 spectrum emission mask 2-605 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1][:resolution]:auto? Spectrum emission mask offset resolution bandwidth auto/manual query function this command queries the on/off state of the automatic resolution bandwidth (rbw) sett...

  • Page 617

    2.13 spectrum emission mask 2-607 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:bandwidth[1]:video? Spectrum emission mask video bandwidth query function this command queries the video bandwidth (vbw) when measuring the reference power for spectrum emission mask measurement. Query [:sense]:...

  • Page 619

    2.13 spectrum emission mask 2-609 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1]:video? Spectrum emission mask offsetvideo bandwidth query function this command queries the video bandwidth (vbw) of the offset for spectrum emission mask measurement. Query [:sense]:...

  • Page 621

    2.13 spectrum emission mask 2-611 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:bandwidth[1]:video:auto? Spectrum emission mask video bandwidth auto/manual query function this command queries the on/off state of the automatic resolution bandwidth (rbw) setting function when measuring the re...

  • Page 622

    Chapter 2 scpi device message details 2-612 [:sense]:semask:offset[1]:list:bandwidth[1]:video:auto [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset video bandwidth auto/manual function this command enables/disables the automatic video bandwidth (vbw) setting function for th...

  • Page 623

    2.13 spectrum emission mask 2-613 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1]:video:auto? Spectrum emission mask offset video bandwidth auto/manual query function this command queries the on/off state of the automatic video bandwidth (vbw) setting function for ...

  • Page 625

    2.13 spectrum emission mask 2-615 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:bandwidth[1]:video:mode? Spectrum emission mask video bandwidth mode query function this command queries the processing method for the video bandwidth (vbw) when measuring the reference power for spectrum emissi...

  • Page 626

    Chapter 2 scpi device message details 2-616 [:sense]:semask:offset[1]:list:bandwidth[1]:video:mode [,[,[,[,[,d_6>[,[,[,[,[,[ ,]]]]]]]]]]] spectrum emission mask offset video bandwidth mode function this command sets the processing method for the video bandwidth (vbw) of the offset for spectrum emiss...

  • Page 627

    2.13 spectrum emission mask 2-617 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1]:video:mode? Spectrum emission mask offset video bandwidth mode query function this command queries the processing method for the video bandwidth (vbw) of the offset for spectrum emiss...

  • Page 628

    Chapter 2 scpi device message details 2-618 [:sense]:semask:sweep[1]:time spectrum emission mask sweep time function this command sets the sweep time when measuring the reference power for spectrum emission mask measurement. Command [:sense]:semask:sweep[1]:time parameter sweep time range [ms269xa] ...

  • Page 629

    2.13 spectrum emission mask 2-619 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1]:time? Spectrum emission mask sweep time query function this command queries the sweep time when measuring the reference power for spectrum emission mask measurement. Query [:sense]:semask:sweep[1]:time?...

  • Page 630

    Chapter 2 scpi device message details 2-620 [:sense]:semask:offset[1]:list:sweep[1]:time [,[,[,[,[,[,[,me_8>[,[,[,[,]]]]]]]]]]] spectrum emission mask offset sweep time function this command sets the sweep time of the offset for spectrum emission mask measurement. Command [:sense]:semask:offset[1]:l...

  • Page 631

    2.13 spectrum emission mask 2-621 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:sweep[1]:time? Spectrum emission mask offset sweep time query function this command queries the sweep time for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:sweep[1]:tim...

  • Page 633

    2.13 spectrum emission mask 2-623 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1]:time:auto? Spectrum emission mask sweep time auto/manual query function this command queries the on/off state of the automatic sweep time setting function when measuring the reference power for spectrum...

  • Page 634

    Chapter 2 scpi device message details 2-624 [:sense]:semask:offset[1]:list:sweep[1]:time:auto [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset sweep time auto/manual function this command enables/disables the automatic sweep time setting function for the offset during spect...

  • Page 635

    2.13 spectrum emission mask 2-625 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:sweep[1]:time:auto? Spectrum emission mask offset sweep time auto/manual query function this command queries the automatic sweep time setting function on/off state for the offset during spectrum e...

  • Page 637

    2.13 spectrum emission mask 2-627 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1]:time:auto:mode? Spectrum emission mask auto sweep time select query function this command queries the sweep mode (normal/fast) when the automatic sweep time setting function is enabled for measuring the...

  • Page 638

    Chapter 2 scpi device message details 2-628 [:sense]:semask:offset[1]:list:sweep[1]:time:auto:mode [,[,[,[,[,[,de_7>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset auto sweep time select function this command queries the sweep mode (normal/fast) when the automatic sweep time setting function is ...

  • Page 639

    2.13 spectrum emission mask 2-629 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:sweep[1]:time:auto:mode? Spectrum emission mask offset auto sweep time select query function this command queries the sweep mode (normal/fast) when the automatic sweep time setting function is ena...

  • Page 641

    2.13 spectrum emission mask 2-631 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:detector[:function]? Spectrum emission mask detection mode query function this command queries the detection mode of the waveform pattern when measuring the reference power for spectrum emission mask measurement...

  • Page 643

    2.13 spectrum emission mask 2-633 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:detector[:function]? Spectrum emission mask detection mode query function this command queries the detection mode of the waveform pattern when measuring the reference power for spectrum emission mask measureme...

  • Page 644

    Chapter 2 scpi device message details 2-634 [:sense]:semask:offset[1]:list:detector [,[,[,[,[,[,de_7>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset detection mode function this command selects the detection mode of the waveform pattern of the offset for spectrum emission mask measurement. Comma...

  • Page 645

    2.13 spectrum emission mask 2-635 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:detector? Spectrum emission mask offset detection mode query function this command queries the detection mode of the waveform pattern of the offset for spectrum emission mask measurement. Query [:...

  • Page 647

    2.13 spectrum emission mask 2-637 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1]:points spectrum emission mask trace point function this command selects the number of frequency display points when measuring the reference power for spectrum emission mask measurement. Command [:sense]...

  • Page 648

    Chapter 2 scpi device message details 2-638 [:sense]:semask:sweep[1]:points? Spectrum emission mask trace point query function this command queries the number of frequency display points when measuring the reference power for spectrum emission mask measurement. Query [:sense]:semask:sweep[1]:points?...

  • Page 649

    2.13 spectrum emission mask 2-639 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:sweep[1]:points [,[,[,[,[,>[,[,[,[,[,[,er_12>]]]]]]]]]]] spectrum emission mask offset trace point function this command queries the number of frequency display points of the offset for spectrum e...

  • Page 650

    Chapter 2 scpi device message details 2-640 [:sense]:semask:offset[1]:list:sweep[1]:points? Spectrum emission mask offset trace point query function this command queries the frequency display point number of the offset for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:swee...

  • Page 652

    Chapter 2 scpi device message details 2-642 [:sense]:semask:filter:type? Spectrum emission mask reference filter type query function this command queries the filter type when measuring the reference power for spectrum emission mask measurement. Query [:sense]:semask:filter:type? Response parameter f...

  • Page 653

    2.13 spectrum emission mask 2-643 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:filter[:rrc]:alpha spectrum emission mask reference roll-off factor function this command sets the rolloff ratio of the filter when measuring the reference power for spectrum emission mask measurement. Command [...

  • Page 654

    Chapter 2 scpi device message details 2-644 [:sense]:semask:filter[:rrc]:alpha? Spectrum emission mask reference roll-off factor query function this command queries the rolloff ratio of the filter when measuring the reference power for spectrum emission mask measurement. Query [:sense]:semask:filter...

  • Page 655

    2.13 spectrum emission mask 2-645 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:frequency:start [,[,[,[,[,[,[,_8>[,[,[,[,]]]]]]]]]]] spectrum emission mask offset start frequency function this command sets the start frequency of the offset for spectrum emission mask measureme...

  • Page 656

    Chapter 2 scpi device message details 2-646 [:sense]:semask:offset[1]:list:frequency:start? Spectrum emission mask offset start frequency query function this command queries the start frequency of the offset for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:frequency:start...

  • Page 657

    2.13 spectrum emission mask 2-647 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:frequency:stop [,[,[,[,[,[,[,_8>[,[,[,[,]]]]]]]]]]] spectrum emission mask offset stop frequency function this command sets the stop frequency of the offset for spectrum emission mask measurement....

  • Page 658

    Chapter 2 scpi device message details 2-648 [:sense]:semask:offset[1]:list:frequency:stop? Spectrum emission mask offset stop frequency query function this command queries the stop frequency of the offset for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:frequency:stop? Re...

  • Page 659

    2.13 spectrum emission mask 2-649 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1]:integration [,[,[,[,h_5>[,[,[,[,[,ndwidth_10>[,[,]]]]]]]]]]] spectrum emission mask offset integrate bandwidth function this command sets integrate bw of the offset for spectrum emiss...

  • Page 660

    Chapter 2 scpi device message details 2-650 [:sense]:semask:offset[1]:list:bandwidth[1]:integration? Spectrum emission mask offset integrate bandwidth query function this command queries integrate bw of the offset for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:bandwidth...

  • Page 661

    2.13 spectrum emission mask 2-651 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:bandwidth[1]:integration:auto [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset integrate bandwidth auto/manual function this command enables/disables the automatic integr...

  • Page 662

    Chapter 2 scpi device message details 2-652 [:sense]:semask:offset[1]:list:bandwidth[1]:integration:auto? Spectrum emission mask offset integrate bandwidth auto/manual query function this command queries the on/off state of the automatic integrate bw setting function for spectrum emission mask measu...

  • Page 663

    2.13 spectrum emission mask 2-653 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:rlevel [,[,[,[,[,[,>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset reference level function this command sets the reference level of the offset for spectrum emission mask measurement. Command...

  • Page 664

    Chapter 2 scpi device message details 2-654 [:sense]:semask:offset[1]:list:rlevel? Spectrum emission mask offset reference level query function this command queries the reference level for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:rlevel? Response parameter reference l...

  • Page 665

    2.13 spectrum emission mask 2-655 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:rlevel:auto [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset reference level auto/manual function this command enables/disables the automatic reference level setting func...

  • Page 666

    Chapter 2 scpi device message details 2-656 [:sense]:semask:offset[1]:list:rlevel:auto? Spectrum emission mask offset reference level auto/manual query function this command queries the automatic reference level setting function on/off state for the offset during spectrum emission mask measurement. ...

  • Page 667

    2.13 spectrum emission mask 2-657 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:state [,[,[,[,[,[, switch_7>[,[,[,[,[,] ]]]]]]]]]] spectrum emission mask offset on/off function this command sets the offset for spectrum emission mask measurement on/off. Command [:sense]:semask...

  • Page 668

    Chapter 2 scpi device message details 2-658 [:sense]:semask:offset[1]:list:state? Spectrum emission mask offset on/off query function this command queries the on/off state of the offset for spectrum emission mask measurement. Query [:sense]:semask:offset[1]:list:state? Response parameter offset-n on...

  • Page 677

    2.13 spectrum emission mask 2-667 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:start:rcarrier [,[,[,[,[,[,>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset start frequency limit level function this command sets the relative level upper limit of the offset start frequency ...

  • Page 678

    Chapter 2 scpi device message details 2-668 [:sense]:semask:offset[1]:list:start:rcarrier? Spectrum emission mask offset start frequency limit level query function this command queries the relative level upper limit of the offset start frequency for spectrum emission mask measurement. Query [:sense]...

  • Page 679

    2.13 spectrum emission mask 2-669 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:offset[1]:list:start:rcarrier [,[,[,[,[,[,>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset start frequency limit level function this command sets the relative level upper limit of the offset start frequenc...

  • Page 680

    Chapter 2 scpi device message details 2-670 :calculate:semask:offset[1]:list:start:rcarrier? Spectrum emission mask offset start frequency limit level query function this command sets the relative level upper limit of the offset start frequency for spectrum emission mask measurement. Query :calculat...

  • Page 681

    2.13 spectrum emission mask 2-671 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:offset[1]:list:stop:rcarrier [,[,[,[,[,[,>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset stop frequency limit level function this command sets the relative level upper limit of the offset stop frequency for...

  • Page 682

    Chapter 2 scpi device message details 2-672 [:sense]:semask:offset[1]:list:stop:rcarrier? Spectrum emission mask offset stop frequency limit level query function this command sets the relative level upper limit of the offset stop frequency for spectrum emission mask measurement. Query [:sense]:semas...

  • Page 683

    2.13 spectrum emission mask 2-673 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:offset[1]:list:stop:rcarrier [,[,[,[,[,[,>[,[,[,[,[,]]]]]]]]]]] spectrum emission mask offset stop frequency limit level function this command sets the relative level upper limit of the offset stop frequency f...

  • Page 684

    Chapter 2 scpi device message details 2-674 :calculate:semask:offset[1]:list:stop:rcarrier? Spectrum emission mask offset stop frequency limit level query function this command sets the relative level upper limit of the offset stop frequency for spectrum emission mask measurement. Query :calculate:s...

  • Page 685

    2.13 spectrum emission mask 2-675 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:logic:offset[1]:list:test [,[,[,[,[,[,[, [,[,[,[,]]]]]]]]]]] spectrum emission mask fail logic function this command selects the judgment method of the offset for spectrum emission mask measurement. Command [:se...

  • Page 686

    Chapter 2 scpi device message details 2-676 related command this command has the same function as the following command. :calculate:semask:logic:offset[1]:list:test [:sense]:semask:logic:offset[1]:list:test? Spectrum emission mask fail logic query function this command queries the judgment method of...

  • Page 687

    2.13 spectrum emission mask 2-677 2 sc pi d ev ice m es sa ge d et ail s and the absolute level upper limit 2. Example of use to query the judgment result. Sem:log:off:list:test? > abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs related command this command has the same function as the following com...

  • Page 688

    Chapter 2 scpi device message details 2-678 judges “or” using the absolute level upper limit 1 and relative level upper limit. Judges “and” using the result and the absolute level upper limit 2. And2 abs1 and abs2 judges using the absolute level upper limit 1 and the absolute level upper limit 2. Ex...

  • Page 689

    2.13 spectrum emission mask 2-679 2 sc pi d ev ice m es sa ge d et ail s :calculate:semask:logic:offset[1]:list:test? Spectrum emission mask fail logic query function this command queries the judgment method of the offset for spectrum emission mask measurement. Query :calculate:semask:logic:offset[1...

  • Page 690

    Chapter 2 scpi device message details 2-680 > abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,off,off related command this command has the same function as the following command. [:sense]:semask:logic:offset[1]:list:test? :configure:semask spectrum emission mask configure function this command sets ...

  • Page 691

    2.13 spectrum emission mask 2-681 2 sc pi d ev ice m es sa ge d et ail s :fetch:semask[n]? Spectrum emission mask fetch function this command outputs the measurement result of spectrum emission mask measurement. Query :fetch:semask[n]? Response when the result mode is a: ,,, ,, ,, ,, ,, ,, ,, ,, ,, ...

  • Page 692

    Chapter 2 scpi device message details 2-682 ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, -999.0,-999.0, ,, ,, ,, ,, ,, ,, ,, (n=1 or when omitted.).

  • Page 693

    2.13 spectrum emission mask 2-683 2 sc pi d ev ice m es sa ge d et ail s -999.0,-999.0, ,, ,, ,, ,, ,, , (n=7 or 8) -999.0,-999.0, ,, ,, ,, ,, ,, , (n=10) -999.0,-999.0, ,, ,, ,, ,, ,, , (n=11) ,, ,, ,, ,, ,, ...... ,, ,, ,, , (n=13).

  • Page 694

    Chapter 2 scpi device message details 2-684 parameter reference absolute power peak value of absolute power of lower offset-n peak value of absolute power of upper offset-n no suffix code, dbm unit, 0.001 db resolution. “–999.0” is returned when no measurement is performed. Peak value of relative po...

  • Page 695

    2.13 spectrum emission mask 2-685 2 sc pi d ev ice m es sa ge d et ail s details this function outputs the measurement result at the spectrum emission mask measurement performed last. It is possible to output the measurement result in a state that the measurement has already been done, and in a diff...

  • Page 696

    Chapter 2 scpi device message details 2-686 :read:semask[n]? Spectrum emission mask read function this command outputs spectrum emission mask measurement and outputs the measurement result. It achieves the same result as when commands are sent in the order of :initiate:semask :fetch:semask[n]? :meas...

  • Page 698

    Chapter 2 scpi device message details 2-688 [:sense]:semask:filter[:rrc][:state]? Spectrum emission mask root nyquist filter state query function this command queries the filter type for spectrum emission mask measurement. Query [:sense]:semask:filter[:rrc][:state]? Response parameter filter type 0 ...

  • Page 700

    Chapter 2 scpi device message details 2-690 :display:semask:annotation:title:data title entry function this command registers the title character string. Command :display:semask:annotation:title:data parameter character string within 32 characters enclosed by double quotation marks (" ") or single q...

  • Page 701

    2.13 spectrum emission mask 2-691 2 sc pi d ev ice m es sa ge d et ail s :display:semask:annotation:title:data? Title entry query function this command queries the title character string. Command :display:semask:annotation:title:data? Parameter character string within 32 characters enclosed by doubl...

  • Page 702

    Chapter 2 scpi device message details 2-692 :display:semask:view[1]:window[1]:trace:y[:scale]:pdivision log scale range function this command sets the y-axis scale magnification when scale mode is set to log. Command display:semask:view[1]:window[1]:trace:y[:scale]:pdivisi on parameter y-axis scale ...

  • Page 703

    2.13 spectrum emission mask 2-693 2 sc pi d ev ice m es sa ge d et ail s :display:semask:view[1]:window[1]:trace:y[:scale]:pdivision? Log scale range query function this command queries the y-axis scale magnification when scale mode is set to log. Query :display:semask:view[1]:window[1]:trace:y[:sca...

  • Page 704

    Chapter 2 scpi device message details 2-694 :display:semask:view[1]:window[1]:trace:y[:scale]:rlevel reference level function this command sets the reference level. Command :display:semask:view[1]:window[1]:trace:y[:scale]:rlevel parameter reference level range value equivalent to –120 to +50 dbm re...

  • Page 705

    2.13 spectrum emission mask 2-695 2 sc pi d ev ice m es sa ge d et ail s related command this command has the same function as the following commands. :display:window[1]:trace:y[:scale]:rlevel :display:acpower:view[1]:window[1]:trace:y[:scale]:rleve l :display:chpower:view[1]:window[1]:trace:y[:scal...

  • Page 706

    Chapter 2 scpi device message details 2-696 :display:semask:view[1]:window[1]:trace:y[:scale]:rlevel? Reference level query function this command queries the reference level. Query :display:semask:view[1]:window[1]:trace:y[:scale]:rlevel ? Response parameter reference level range value equivalent to...

  • Page 707

    2.13 spectrum emission mask 2-697 2 sc pi d ev ice m es sa ge d et ail s :display:semask:view[1]:window[1]:page:number page number function this command sets the display page number of spectrum emission mask. Command :display:semask:view[1]:window[1]:page:number parameter page number range 1 to 2 re...

  • Page 710

    Chapter 2 scpi device message details 2-700 details [ms269xa] sg marker trigger can be selected only when the option 020/120 vector signal generator is installed. Bbif trigger cannot be selected only when the option 040/140 baseband interface unit is not installed or the software package is ver.6.00...

  • Page 711

    2.13 spectrum emission mask 2-701 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:average:count average count function this command sets the storage count. Command [:sense]:semask:average:count parameter storage count range 2 to 9999 default 10 example of use to set the storage count to 110. ...

  • Page 712

    Chapter 2 scpi device message details 2-702 [:sense]:semask:average:count? Average count query function this command queries the storage count. Command [:sense]:semask:average:count? Parameter storage count range 2 to 9999 default 10 example of use to query the storage count. Sem:aver:coun? > 110 re...

  • Page 714

    Chapter 2 scpi device message details 2-704 [:sense]:semask:average[:state]? Storage mode query function this command queries the storage mode for trace a. Query [:sense]:semask:average[:state]? Response parameter setting of storage mode 1 linear average 0 other than linear average example of use to...

  • Page 716

    Chapter 2 scpi device message details 2-706 [:sense]:semask:racouple? Couple ref & att query function this command sets the shared setting for reference level and attenuator for spectrum emission mask measurement to on/off. Query [:sense]:semask:racouple? Response parameter shared setting on/off 1 s...

  • Page 717

    2.13 spectrum emission mask 2-707 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1][:type][:auto]:rules:fft:rwidth? Spectrum emission mask sweep type select rules real fft width query function this command queries the fft width that is actually used for the sweep/fft switch rule during...

  • Page 718

    Chapter 2 scpi device message details 2-708 [:sense]:semask:offset[1]:list:sweep[1][:type][:auto]:rules:fft:rw idth? Spectrum emission mask offset sweep type select rules real fft width query function this command queries the fft width that is actually used for the sweep/fft switch rule during offse...

  • Page 719

    2.13 spectrum emission mask 2-709 2 sc pi d ev ice m es sa ge d et ail s [:sense]:semask:sweep[1][:type][:auto]:rules:rtype? Spectrum emission mask sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during reference power measurement ...

  • Page 720

    Chapter 2 scpi device message details 2-710 [:sense]:semask:offset[1]:list:sweep[1][:type][:auto]:rules:rtype ? Spectrum emission mask offset sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during offset measurement in the spectrum...

  • Page 721

    2.14 spurious emission measurement function 2-711 2 sc pi d ev ice m es sa ge d et ail s 2.14 spurious emission measurement function table 2.14-1 lists device messages for setting the spurious emission measurement functions. Table 2.14-1 device messages for spurious emission measurement function fun...

  • Page 722

    Chapter 2 scpi device message detail 2-712 table 2.14-1 device messages for spurious emission measurement function (cont’d) function device message spurious emission stop frequency [:sense]:spurious[:range][:list]:frequency:stop ,,,,,,,q_8>,,,,,,,eq_15>,,,,, [:sense]:spurious[:range][:list]:frequenc...

  • Page 725

    2.14 spurious emission measurement function 2-715 2 sc pi d ev ice m es sa ge d et ail s table 2.14-1 device messages for spurious emission measurement function (cont’d) function device message spurious emission limit start level :calculate:spurious[:range][:list]:limit:absolute[:upper]:data[:sta rt...

  • Page 726

    Chapter 2 scpi device message detail 2-716 table 2.14-1 device message for spurious emission measurement function (cont’d) function device message spurious emission time domain rbw [:sense]:spurious:tdomain:[:range][:list]:bandwidth[:resolution] ,,,,5>,,,,,th_10>,,,,, ,,,,dth_19>, [:sense]:spurious:...

  • Page 727

    2.14 spurious emission measurement function 2-717 2 sc pi d ev ice m es sa ge d et ail s table 2.14-1 device messages for spurious emission measurement function (cont’d) function device message recall spurious emission parameter :mmemory:load:spurious:table spurious emission configure :configure:spu...

  • Page 730

    Chapter 2 scpi device message detail 2-720 [:sense]:spurious[:state]? Measure spurious emission query function this command queries the on/off state of the spurious emission measurement. Query [:sense]:spurious[:state]? Response parameter spurious measurement on/off 1 on 0 off example of use to quer...

  • Page 732

    Chapter 2 scpi device message detail 2-722 [:sense]:spurious:type? Spurious emission result type query function this command queries the measurement result type. Query [:sense]:spurious:type? Response parameter measurement result type wors point with the least margin from the limit line is displayed...

  • Page 733

    2.14 spurious emission measurement function 2-723 2 sc pi d ev ice m es sa ge d et ail s :display:spurious:segment:mode? Displayed segment mode query function this command queries the display mode of a segment. Query :display:spurious:segment:mode? Response parameter display mode 1 auto 0 manual exa...

  • Page 734

    Chapter 2 scpi device message detail 2-724 example of use to specify 2 as the segment in which the trace data is displayed. Disp:spur:segm 2 :display:spurious:segment? Displayed segment query function this command queries the segment to display the trace data in. Query :display:spurious:segment? Res...

  • Page 737

    2.14 spurious emission measurement function 2-727 2 sc pi d ev ice m es sa ge d et ail s example of use to query the content setting in the summary table. Disp:spur:stab? >res :display:spurious:segment:next next page function this command displays the summary on the next page. Command :display:spuri...

  • Page 738

    Chapter 2 scpi device message detail 2-728 :display:spurious:segment:restart? Displayed restart query function this command queries whether the remeasurement message is displayed on the trace. Query :display:spurious:segment:restart? Response parameter message displayed/not displayed 1 message is di...

  • Page 741

    2.14 spurious emission measurement function 2-731 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious:segment:number edit segment number function this command sets the number of the segment to set a parameter in. Command [:sense]:spurious:segment:number parameter segment number range 1 to 20 re...

  • Page 743

    2.14 spurious emission measurement function 2-733 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:segment:state? Segment on/off query function this command queries the on/off state of the segment. Query [:sense]:spurious[:range][:list]:segment:state? Response parameter segmen...

  • Page 744

    Chapter 2 scpi device message detail 2-734 [:sense]:spurious[:range][:list]:frequency:start ,,,,,,,, ,,,,,,,eq_16>,,,, spurious emission start frequency function this command sets the start frequency of each segment. Command [:sense]:spurious[:range][:list]:frequency:start parameter start frequency ...

  • Page 745

    2.14 spurious emission measurement function 2-735 2 sc pi d ev ice m es sa ge d et ail s segment 10 7 ghz (1 ghz for ms2690a) segment 11 8 ghz (1 ghz for ms2690a) segment 12 9 ghz (1 ghz for ms2690a) segment 13 10 ghz (1 ghz for ms2690a) segment 14 11 ghz (1 ghz for ms2690a) segment 15 12 ghz (1 ghz...

  • Page 746

    Chapter 2 scpi device message detail 2-736 segment 14 11 ghz (1 ghz for option 040/041) segment 15 12 ghz (1 ghz for option 040/041) segment 16 14 ghz (1 ghz for option 040/041) segment 17 18 ghz (1 ghz for option 040/041) segment 18 24 ghz (1 ghz for option 040/041) segment 19 32 ghz (1 ghz for opt...

  • Page 747

    2.14 spurious emission measurement function 2-737 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:frequency:start? Spurious emission start frequency query function this command queries the start frequency of each segment. Query [:sense]:spurious[:range][:list]:frequency:start...

  • Page 748

    Chapter 2 scpi device message detail 2-738 [:sense]:spurious[:range][:list]:frequency:stop ,,,,,,,, ,,,,,,,eq_16>,,,, spurious emission stop frequency function this command sets the stop frequency of each segment. Command [:sense]:spurious[:range][:list]:frequency:stop parameter stop frequency of se...

  • Page 749

    2.14 spurious emission measurement function 2-739 2 sc pi d ev ice m es sa ge d et ail s segment 13 11 ghz (6 ghz for ms2690a) segment 14 12 ghz (6 ghz for ms2690a) segment 15 to 20 12.75 ghz (6 ghz for ms2690a) [ms2830a] segment 1 150 khz segment 2 30 mhz segment 3 1 ghz segment 4 2 ghz segment 5 3...

  • Page 750

    Chapter 2 scpi device message detail 2-740 044) [ms2840a] segment 1 150 khz segment 2 30 mhz segment 3 1 ghz segment 4 2 ghz segment 5 3 ghz segment 6 4 ghz (3.6 ghz for option 040) segment 7 5 ghz (3.6 ghz for option 040) segment 8 6 ghz (3.6 ghz for option 040) segment 9 7 ghz (3.6 ghz for option ...

  • Page 751

    2.14 spurious emission measurement function 2-741 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:frequency:stop? Spurious emission stop frequency query function this command queries the stop frequency of each segment. Query [:sense]:spurious[:range][:list]:frequency:stop? Re...

  • Page 752

    Chapter 2 scpi device message detail 2-742 :display:spurious:view[1]:window[1]:trace:y[:scale]:rlevel ,,,,,,,, real_9>,,,,,,,l_16>,,,, spurious emission reference level function this command sets the reference level of each segment. Command :display:spurious:view[1]:window[1]:trace:y[:scale]:rlev el...

  • Page 753

    2.14 spurious emission measurement function 2-743 2 sc pi d ev ice m es sa ge d et ail s :display:spurious:view[1]:window[1]:trace:y[:scale]:rlevel? Spurious emission reference level query function this command queries the reference level of each segment. Query :display:spurious:view[1]:window[1]:tr...

  • Page 755

    2.14 spurious emission measurement function 2-745 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious:attenuation? Spurious emission attenuator query function this command queries the attenuator value of each segment. Query [:sense]:spurious:attenuation? Response parameter attenuator value of s...

  • Page 757

    2.14 spurious emission measurement function 2-747 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:bandwidth[:resolution]:auto? Spurious emission resolution bandwidth auto/manual query function this command queries the auto/manual state of rbw in each segment. Query [:sense]:s...

  • Page 758

    Chapter 2 scpi device message detail 2-748 [:sense]:spurious[:range][:list]:bandwidth[:resolution] ,,,,5>,,,,,h_10>,,,,, bandwidth_15>,,,,th_19>, spurious emission resolution bandwidth function this command sets the resolution bandwidth (rbw) of each segment. Command [:sense]:spurious[:range][:list]...

  • Page 759

    2.14 spurious emission measurement function 2-749 2 sc pi d ev ice m es sa ge d et ail s segment 9 to 15 1 mhz (auto for option 040/041) segment 16 to 18 1 mhz (auto for option 040/041/043) segment 19 to 20 1 mhz (auto for option 040/041/043/044) [ms2840a] segment 7 to 8 1 mhz (auto for option 040) ...

  • Page 760

    Chapter 2 scpi device message detail 2-750 [:sense]:spurious[:range][:list]:bandwidth[:resolution]? Spurious emission resolution bandwidth query function this command queries the resolution bandwidth (rbw) of each segment. Query [:sense]:spurious[:range][:list]:bandwidth[:resolution]? Response param...

  • Page 762

    Chapter 2 scpi device message detail 2-752 [:sense]:spurious[:range][:list]:bandwidth:video:auto? Spurious emission video bandwidth auto/manual query function this command queries the auto/manual state of the video bandwidth (rbw) in each segment. Query [:sense]:spurious[:range][:list]:bandwidth:vid...

  • Page 764

    Chapter 2 scpi device message detail 2-754 [:sense]:spurious[:range][:list]:bandwidth:video? Spurious emission video bandwidth query function this command queries the video bandwidth (vbw) of each segment. Query [:sense]:spurious[:range][:list]:bandwidth:video? Response parameter video bandwidth (vb...

  • Page 766

    Chapter 2 scpi device message detail 2-756 [:sense]:spurious[:range][:list]:sweep:time:auto? Spurious emission sweep time auto/manual query function this command queries the auto/manual state of the sweep time in each segment. Query [:sense]:spurious[:range][:list]:sweep:time:auto? Response paramete...

  • Page 767

    2.14 spurious emission measurement function 2-757 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:sweep:time ,,,,,nds_6>,,,,,11>,,,,,16>,,,, spurious emission sweep time function this command sets the sweep time of each segment. Command [:sense]:spurious[:range][:list]:sweep:...

  • Page 768

    Chapter 2 scpi device message detail 2-758 [:sense]:spurious[:range][:list]:sweep:time? Spurious emission sweep time query function this command queries the sweep time of each segment. Query [:sense]:spurious[:range][:list]:sweep:time? Response parameter range [ms269xa] 2 ms to 1000 s [ms2830a] 1 ms...

  • Page 770

    Chapter 2 scpi device message detail 2-760 [:sense]:spurious[:range][:list]:sweep:pause? Pause before sweep query function this command queries the setting to pause before sweep of each segment. Query [:sense]:spurious[:range][:list]:sweep:pause? Response parameter pause before sweep on/off 1 pause ...

  • Page 772

    Chapter 2 scpi device message detail 2-762 [:sense]:spurious:power[:rf]:gain[:state]? Spurious emission preamp on/off query function this command queries the on/off state of the pre-amp in each segment. Query [:sense]:spurious:power[:rf]:gain[:state]? Response parameter pre-amp on/off 1 on 0 off exa...

  • Page 774

    Chapter 2 scpi device message detail 2-764 [:sense]:spurious[:range][:list]:detector[1][:function]? Spurious emission detection mode query function this command queries the detection mode of the waveform pattern in each segment. Query [:sense]:spurious[:range][:list]:detector[1][:function]? Response...

  • Page 775

    2.14 spurious emission measurement function 2-765 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:sweep:points ,,,,,, integer_7>,,,,, ,,,,,,er_18>,, spurious emission trace point function this command sets the number of the points in the trace data of each segment. Command [:...

  • Page 776

    Chapter 2 scpi device message detail 2-766 example of use to set the number of the points in the trace data of each segment. Spur:swe:poin 1001,5001,5001,5001,10001,10001,10001,10001,10001,10001, 10001,10001,10001,10001,10001,10001,10001,10001,10001,10 001 [:sense]:spurious[:range][:list]:sweep:poin...

  • Page 778

    Chapter 2 scpi device message detail 2-768 [:sense]:spurious:average:count:couple? Couple storage count query function this command queries the on/off state of the shared setting of the storage count in each segment. Query [:sense]:spurious:average:count:couple? Response parameter shared setting of ...

  • Page 779

    2.14 spurious emission measurement function 2-769 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:average:count ,,,,,, integer_7>,,,,, ,,,,,,er_18>,, spurious emission storage count function this command sets the storage count of each segment. Command [:sense]:spurious[:range...

  • Page 780

    Chapter 2 scpi device message detail 2-770 [:sense]:spurious[:range][:list]:average:count? Spurious emission storage count query function this command queries the storage count of each segment. Query [:sense]:spurious[:range][:list]:average:count? Response parameter storage count of segment n range ...

  • Page 781

    2.14 spurious emission measurement function 2-771 2 sc pi d ev ice m es sa ge d et ail s :calculate:spurious[:range][:list]:correction:recall ,[,] recall correction table function this command selects the correction table to use in a segment. Command :calculate:spurious[:range][:list]:correction:rec...

  • Page 782

    Chapter 2 scpi device message detail 2-772 :calculate:spurious[:range][:list]:limit:absolute[:upper]:data[:start] ,,,,,,, mpl_8>,,,,,, ,,,,,, spurious emission limit start level function this command sets the absolute level limit of the start frequency in each segment for the spurious emission measu...

  • Page 783

    2.14 spurious emission measurement function 2-773 2 sc pi d ev ice m es sa ge d et ail s :calculate:spurious[:range][:list]:limit:absolute[:upper]:data[:start] ? Spurious emission limit start level query function this command queries the absolute level limit of the start frequency in each segment fo...

  • Page 785

    2.14 spurious emission measurement function 2-775 2 sc pi d ev ice m es sa ge d et ail s :calculate:spurious[:range][:list]:limit:absolute[:upper]:data:stop: auto? Spurious emission limit stop level auto/manual query function this command queries auto/manual of the absolute level limit of the stop f...

  • Page 786

    Chapter 2 scpi device message detail 2-776 :calculate:spurious[:range][:list]:limit:absolute[:upper]:data:stop ,,,,,,, mpl_8>,,,,,, ,,,,,, spurious emission limit stop level function this command sets the absolute level limit of the stop frequency of each segment for the spurious emission measuremen...

  • Page 787

    2.14 spurious emission measurement function 2-777 2 sc pi d ev ice m es sa ge d et ail s :calculate:spurious[:range][:list]:limit:absolute[:upper]:data:stop? Spurious emission limit stop level query function this command queries the absolute level limit of the stop frequency in each segment for the ...

  • Page 790

    Chapter 2 scpi device message detail 2-780 [:sense]:spurious[:range][:list]:peak:threshold ,,,,,,,, real_9>,,,,,,,l_16>,,,, spurious emission search threshold level function this command sets the spurious search threshold when result type is peaks. Command [:sense]:spurious[:range][:list]:peak:thres...

  • Page 791

    2.14 spurious emission measurement function 2-781 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious[:range][:list]:peak:threshold? Spurious emission search threshold level query function this command queries the spurious search threshold when result type is peaks. Query [:sense]:spurious[:ran...

  • Page 793

    2.14 spurious emission measurement function 2-783 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious:tdomain[:range][:list]:bandwidth[:resolution]:co uple? Spurious emission couple segment rbw query function this command queries the on/off state of the setting for whether the same as the value...

  • Page 794

    Chapter 2 scpi device message detail 2-784 [:sense]:spurious:tdomain[:range][:list]:bandwidth[:resolution] ,,,,5>,,,,,h_10>,,,,, bandwidth_15>,,,,th_19>, spurious emission time domain rbw function this command sets rbw in time domain setup. Command [:sense]:spurious:tdomain[:range][:list]:bandwidth[...

  • Page 795

    2.14 spurious emission measurement function 2-785 2 sc pi d ev ice m es sa ge d et ail s example of use to set rbw in time domain setup. Spur:tdom:band 3khz,3khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10kh z,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz, 10khz.

  • Page 796

    Chapter 2 scpi device message detail 2-786 [:sense]:spurious:tdomain[:range][:list]:bandwidth[:resolution]? Spurious emission time domain rbw query function this command queries rbw in time domain setup. Query [:sense]:spurious:tdomain[:range][:list]:bandwidth[:reso lution]? Response parameter resol...

  • Page 798

    Chapter 2 scpi device message detail 2-788 [:sense]:spurious:tdomain[:range][:list]:bandwidth:video:couple? Spurious emission couple segment vbw query function this command queries the on/off state of the setting for whether the same as the value set in segment setup is automatically set to vbw valu...

  • Page 800

    Chapter 2 scpi device message detail 2-790 [:sense]:spurious:tdomain[:range][:list]:bandwidth:video? Spurious emission time domain vbw query function this command queries vbw in time domain setup. Query [:sense]:spurious:tdomain[:range][:list]:bandwidth:video ? Response parameter video bandwidth of ...

  • Page 801

    2.14 spurious emission measurement function 2-791 2 sc pi d ev ice m es sa ge d et ail s [:sense]:spurious:tdomain[:range][:list]:sweep:time ,,,,,nds_6>,,,,,11>,,,,,16>,,,, spurious emission time domain sweep time function this command sets the sweep time in time domain setup. Command [:sense]:spuri...

  • Page 802

    Chapter 2 scpi device message detail 2-792 [:sense]:spurious:tdomain[:range][:list]:sweep:time? Spurious emission time domain sweep time query function this command queries the sweep time in time domain setup. Query [:sense]:spurious:tdomain[:range][:list]:sweep:time? Response parameter sweep time r...

  • Page 804

    Chapter 2 scpi device message detail 2-794 [:sense]:spurious:tdomain[:range][:list]:detector[1][:function]? Spurious emission time domain detection query function this command queries the detection mode of the waveform pattern in time domain setup. Query [:sense]:spurious:tdomain[:range][:list]:dete...

  • Page 805

    2.14 spurious emission measurement function 2-795 2 sc pi d ev ice m es sa ge d et ail s :mmemory:store:spurious:table save spurious emission parameter function this command saves the parameter for the spurious emission measurement. Command :mmemory:store:spurious:table parameter register to be save...

  • Page 806

    Chapter 2 scpi device message detail 2-796 :configure:spurious spurious emission configure function this command sets the spurious emission measurement to on. Command :configure:spurious details no measurement is performed. When spurious emission measurement is set to on, the active trace is set to ...

  • Page 807

    2.14 spurious emission measurement function 2-797 2 sc pi d ev ice m es sa ge d et ail s :fetch:spurious[n]? Spurious emission fetch function this command outputs the measurement result for the spurious emission measurement. Query :fetch:spurious[n]? Response when result mode is a: (when spurious em...

  • Page 808

    Chapter 2 scpi device message detail 2-798 (n=22) ,････ (n=23 to 42) parameter spurious number segment number of the detected spurious number of the detected spurious –999.0 is returned when an error occurs/no measurement is performed. Frequency of spurious values have no suffix code, are in hz unit...

  • Page 809

    2.14 spurious emission measurement function 2-799 2 sc pi d ev ice m es sa ge d et ail s 0 is returned when judged as pass, and 1 is returned when judged as fail. N=2 to 21 returns a comma separated list of the trace data for the selected segment (where segment number = n-1). N=23 to 42 returns a co...

  • Page 810

    Chapter 2 scpi device message detail 2-800 :read:spurious[n]? Spurious emission read function this command performs the spurious emission measurement and outputs the result. It works in the same way as the two commands are transmitted in the following order: :initiate:spurious :fetch:spurious[n]? :m...

  • Page 811

    2.14 spurious emission measurement function 2-801 2 sc pi d ev ice m es sa ge d et ail s :display:spurious:annotation:title:data? Spurious emission title entry query function this command queries the title character string. Refer to :display:annotation:title:data?. Related command this command has t...

  • Page 812

    Chapter 2 scpi device message detail 2-802 :display:spurious:view[1]:window[1]:trace:y[:scale]:pdivision? Spurious emission log scale range query function this command queries the y-axis scale range when scale mode is set to log. Refer to :display:window[1]:trace:y[:scale]:[logarithmic]:pdivisi on?....

  • Page 825

    2.14 spurious emission measurement function 2-815 2 sc pi d ev ice m es sa ge d et ail s :initiate:spurious:pause:continue spurious emission continue function pause is cancelled and measurement will continue when this command is sent while it is in remote control state and paused. Command :initiate:...

  • Page 826

    Chapter 2 scpi device message detail 2-816 :initiate:spurious:pause:state? Spurious emission pause status query function this command queries whether the spurious emission measurement is in remote control state and paused or not. Query :initiate:spurious:pause:state? Response parameter status of the...

  • Page 828

    Chapter 2 scpi device message detail 2-818 [:sense]:spurious:synthesis:lphase? Low phase noise for spurious emission measurement query function this command queries the low phase noise function on/off state during spurious emission measurement. Query [:sense]:spurious:synthesis:lphase? Response low ...

  • Page 829

    2.14 spurious emission measurement function 2-819 2 sc pi d ev ice m es sa ge d et ail s spurious noise generated within the unit. Refer to the mainframe operation manual (operation) for details about spurious noise generation and appropriate conditions for using the low phase noise function. Exampl...

  • Page 830

    Chapter 2 scpi device message detail 2-820 [:sense]:frequency:synthesis:lphase:state? Low phase noise status query function this command queries the state of low phase noise function with the current measurement conditions. Query [:sense]:frequency:synthesis:lphase:state? Response low phase noise fu...

  • Page 831

    2.15 setting the toi measurement functions 2-821 2 sc pi d ev ice m es sa ge d et ail s 2.15 setting the toi measurement functions table 2.15-1 lists device messages for setting the toi measurement functions. Table 2.15-1 device messages for setting the toi measurement functions function device mess...

  • Page 835

    2.15 setting the toi measurement functions 2-825 2 sc pi d ev ice m es sa ge d et ail s [:sense]:toi:frequency:tune:immediate toi frequency auto tune function this command executes the auto tune of the toi measurement. Command [:sense]:toi:frequency:tune:immediate example of use to execute the auto ...

  • Page 836

    Chapter 2 scpi device message detail 2-826 [ms269xa] 2.25 ghz (ms2690a) 5.0625 ghz (ms2691a) 9.9375 ghz (ms2692a) [ms2830a] 1.125 ghz (option 040) 2.25 ghz (option 041) 5.0625 ghz (option 043) 9.9375 ghz (option 044) 16.125 ghz (option 045) [ms2840a] 1.125 ghz (option 040) 2.25 ghz (option 041) 9.93...

  • Page 837

    2.15 setting the toi measurement functions 2-827 2 sc pi d ev ice m es sa ge d et ail s response parameter lower tone frequency for the toi measurement range [ms269xa] −100 mhz to 6.05 ghz (ms2690a) −100 mhz to 13.6 ghz (ms2691a) −100 mhz to 26.6 ghz (ms2692a) [ms2830a] −100 mhz to 3.7 ghz (option 0...

  • Page 838

    Chapter 2 scpi device message detail 2-828 [:sense]:toi:frequency:base:upper toi upper tone frequency function this command sets the upper tone frequency for the toi measurement. Command [:sense]:toi:frequency:base:upper parameter upper tone frequency for the toi measurement range [ms269xa] –100 mhz...

  • Page 839

    2.15 setting the toi measurement functions 2-829 2 sc pi d ev ice m es sa ge d et ail s related command this command has the same function as the following command. :calculate:toi:frequency:base:upper :calculate:toi:frequency:base:upper toi upper tone frequency function this command sets the upper t...

  • Page 840

    Chapter 2 scpi device message detail 2-830 example of use to query the upper tone frequency. Toi:freq:base:upp? > 2000000000 related command this command has the same function as the following command. :calculate:toi:frequency:base:upper? :calculate:toi:frequency:base:upper? Toi upper tone frequency...

  • Page 841

    2.15 setting the toi measurement functions 2-831 2 sc pi d ev ice m es sa ge d et ail s example of use to automatically set the tone frequency. Toi:freq:base:auto on related command this command has the same function as the following command. :calculate:toi:frequency:base[:lower[:upper]]:auto :calcu...

  • Page 842

    Chapter 2 scpi device message detail 2-832 example of use to query whether the automatic setting of the tone frequency for the toi measurement is on or off. Toi:freq:base:auto? > 1 related command this command has the same function as the following command. :calculate:toi:frequency:base[:lower[:uppe...

  • Page 843

    2.15 setting the toi measurement functions 2-833 2 sc pi d ev ice m es sa ge d et ail s [:sense]:toi:zspan[:state]? Toi zero span measurement on/off query function this command queries whether the zero span measurement in the toi measurement is on or off. Query [:sense]:toi:zspan[:state]? Response p...

  • Page 848

    Chapter 2 scpi device message detail 2-838 [:sense]:toi:zspan:sweep:time toi zero span measurement sweep time function this command sets the sweep time for the zero span measurement in the toi measurement. Command [:sense]:toi:zspan:sweep:time parameter sweep time of zero span measurement in the toi...

  • Page 849

    2.15 setting the toi measurement functions 2-839 2 sc pi d ev ice m es sa ge d et ail s [:sense]:toi:zspan:sweep:time? Toi zero span measurement sweep time query function this command queries the sweep time for the zero span measurement in the toi measurement. Query [:sense]:toi:zspan:sweep:time? Re...

  • Page 851

    2.15 setting the toi measurement functions 2-841 2 sc pi d ev ice m es sa ge d et ail s [:sense]:toi:zspan:sweep:time:auto? Toi zero span measurement sweep time auto/manual query function this command queries whether the automatic setting of the sweep time for the zero span measurement in the toi me...

  • Page 853

    2.15 setting the toi measurement functions 2-843 2 sc pi d ev ice m es sa ge d et ail s [:sense]:toi:frequency:im3:search? Toi 3rd frequency search on/off function this command queries whether the search function for the third-order distortion frequency in the toi measurement is on or off. Query [:s...

  • Page 854

    Chapter 2 scpi device message detail 2-844 :configure:toi toi configure function this command turns on the toi measurement. Command :configure:toi details no measurement is made. Example of use to turn on the toi measurement. Conf:toi :initiate:toi toi initiate function this command starts the toi m...

  • Page 855

    2.15 setting the toi measurement functions 2-845 2 sc pi d ev ice m es sa ge d et ail s :fetch:toi[n]? Toi read fetch function this command outputs the measurement result of the toi measurement. Query :fetch:toi[n]? Response ,,... (n=0) ,, ,, ,, (n=1) ,,, ,, ,, ,,, ,,, ,, (n=2) parameter worst value...

  • Page 856

    Chapter 2 scpi device message detail 2-846 toi and absolute level: no suffix code, in dbm units, 0.01 db resolution (–999.0 is returned when there is an error or no measurement is performed.) frequency: no suffix code, in hz unit, 1 hz resolution (–999999999999 is returned when there is an error or ...

  • Page 857

    2.15 setting the toi measurement functions 2-847 2 sc pi d ev ice m es sa ge d et ail s :measure:toi[n]? Toi measure function this command performs the toi measurement and outputs the measurement result. This command has the same function as the following commands executed in this order: :configure:...

  • Page 858

    Chapter 2 scpi device message detail 2-848 :read:toi:ip3? Toi read ip3 function this command performs the toi measurement and outputs the measurement result. This command has the same function as the following commands executed in this order: :initiate:toi :*wai :fetch:toi:ip3? :measure:toi:ip3? Toi...

  • Page 859

    2.16 internal signal generator control function 2-849 2 sc pi d ev ice m es sa ge d et ail s 2.16 internal signal generator control function table 2.16-1 lists device messages for setting the internal signal generator control function. Table 2.16-1 device messages for setting the internal signal gen...

  • Page 861

    2.16 internal signal generator control function 2-851 2 scpi device message details :calculate:sgcontrol[:state]? Internal signal generator control query function this command queries the on/off state of internal signal generator control function. Query :calculate:sgcontrol[:state]? Response paramet...

  • Page 862

    Chapter 2 scpi device message detail 2-852 :calculate:sgcontrol:power internal signal generator control sg output level function this command sets the sg output level when internal signal generator control measurement is executed. Command :calculate:sgcontrol:power parameter sg output level range –4...

  • Page 863

    2.16 internal signal generator control function 2-853 2 sc pi d ev ice m es sa ge d et ail s :calculate:sgcontrol:power? Internal signal generator control sg output level query function this command queries the sg output level. Query :calculate:sgcontrol:power? Response parameter sg output level ran...

  • Page 865

    2.16 internal signal generator control function 2-855 2 sc pi d ev ice m es sa ge d et ail s :output[:state]? Internal signal generator output query function this command queries the on/off state of rf output in the internal signal generator control function. Query :output[:state]? Response paramete...

  • Page 866

    Chapter 2 scpi device message detail 2-856 2.17 configuring batch measurement settings table 2.17-1 lists device messages for setting the batch measurement function. Table 2.17-1 device messages for batch measurement settings function device message reloading parameter list files :mmemory:reload:bat...

  • Page 867

    2.17 configuring batch measurement settings 2-857 2 sc pi d ev ice m es sa ge d et ail s :mmemory:reload:batch [] reloading parameter list files function this command reflects the changes made to the parameter list files of the specified drive. Command :mmemory:reload:batch [] parameter drive name a...

  • Page 868

    Chapter 2 scpi device message detail 2-858 :measure:batch:acp[n]? [,] adjacent channel power batch measure function this command executes acp measurement and outputs the result after the parameters described in the specified parameter list file have been set. Query :measure:batch:acp[n]? [,] respons...

  • Page 869

    2.17 configuring batch measurement settings 2-859 2 sc pi d ev ice m es sa ge d et ail s parameter list format table 2.17-2 lists the parameter list example. Table 2.17-2 parameter list example (acp measurement).

  • Page 870

    Chapter 2 scpi device message detail 2-860 table 2.17-2 parameter list example (acp measurement) (cont’d) describe the setting parameters in the part enclosed between the commonparams elements. The description method consists in describing the parameter name to be set in the name attribute in the at...

  • Page 871

    2.17 configuring batch measurement settings 2-861 2 sc pi d ev ice m es sa ge d et ail s table 2.17-3 parameter list settings (acp measurement) parameter attribute name setting attribute value setting center frequency “center freq.” value is described in hz units. Spurious mode “frequency band spuri...

  • Page 872

    Chapter 2 scpi device message detail 2-862 table 2.17-3 parameter list settings (acp measurement) (cont’d) parameter attribute name setting attribute value setting vbw “vbw value” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “1khz”: 1 khz “3khz”: 3 khz “5khz”: ...

  • Page 873

    2.17 configuring batch measurement settings 2-863 2 sc pi d ev ice m es sa ge d et ail s table 2.17-3 parameter list settings (acp measurement) (cont’d) parameter attribute name setting attribute value setting trigger switch “trigger switch” “off”: off “on”: on trigger source “trigger source” “video...

  • Page 874

    Chapter 2 scpi device message detail 2-864 table 2.17-3 parameter list settings (acp measurement) (cont’d) parameter attribute name setting attribute value setting acp carrier select number “acp carrier select number” describes reference carrier number. Acp in band center “acp in band center” value ...

  • Page 875

    2.17 configuring batch measurement settings 2-865 2 sc pi d ev ice m es sa ge d et ail s :measure:batch:obwidth[n]? [,] occupied bandwidth batch measure function this command executes obw measurement and outputs the measurement result after the parameters described in the specified parameter list fi...

  • Page 876

    Chapter 2 scpi device message detail 2-866 parameter list format table 2.17-4 lists the parameter list example. Table 2.17-4 parameter list example (obw measurement) the description method consists in describing the parameter name to be set in the name attribute in the attribute element, and the set...

  • Page 877

    2.17 configuring batch measurement settings 2-867 2 sc pi d ev ice m es sa ge d et ail s since the settings are done in sequence from the top, be careful about the description order when setting parameters that have relationships of dependence. Also, if a value that is either out of the setting rang...

  • Page 878

    Chapter 2 scpi device message detail 2-868 table 2.17-5 parameter list settings (obw measurement) (cont’d) parameter attribute name setting attribute value setting vbw “vbw value” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “1khz”: 1 khz “3khz”: 3 khz “5khz”: ...

  • Page 879

    2.17 configuring batch measurement settings 2-869 2 sc pi d ev ice m es sa ge d et ail s table 2.17-5 parameter list settings (obw measurement) (cont’d) parameter attribute name setting attribute value setting trigger switch “trigger switch” “off”: off “on”: on trigger source “trigger source” “video...

  • Page 880

    Chapter 2 scpi device message detail 2-870 :measure:batch:semask[n]? [,] spectrum emission mask batch measure function this command executes spectrum emission mask measurement and outputs the measurement result after the parameters described in the specified parameter list file have been set. Query ...

  • Page 881

    2.17 configuring batch measurement settings 2-871 2 sc pi d ev ice m es sa ge d et ail s example of use to acquire the peak value of absolute power of sem measurement using the myparam.Xls parameter list file (n = 10). Meas:batc:sem10? "myparam" > 999.0,-999.0,-100.000,-100.000,-60.000,-60.000,45.00...

  • Page 882

    Chapter 2 scpi device message detail 2-872 table 2.17-6 parameter list example (sem measurement).

  • Page 883

    2.17 configuring batch measurement settings 2-873 2 sc pi d ev ice m es sa ge d et ail s table 2.17-6 parameter list example (sem measurement) (cont’d).

  • Page 884

    Chapter 2 scpi device message detail 2-874 describe the setting parameters in the part enclosed between the commonparams elements. The description method consists in describing the parameter name to be set in the name attribute in the attribute element, and the setting value in value. The parts in b...

  • Page 885

    2.17 configuring batch measurement settings 2-875 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting trigger switch “trigger switch” “off”: off “on”: on trigger source “trigger source” “video...

  • Page 886

    Chapter 2 scpi device message detail 2-876 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem reference mode “sem reference mode” “channel”: channel “peak”: peak “fix”: fix sem reference power “sem reference power” value is de...

  • Page 887

    2.17 configuring batch measurement settings 2-877 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem reference vbw “sem vbw value” “1 hz”: 1 hz “3 hz”: 3 hz “10 hz”: 10 hz “30hz”: 30 hz “...

  • Page 888

    Chapter 2 scpi device message detail 2-878 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 switch “sem offset1 switch” “off”: off “on”: on sem offset2 switch “sem offset2 switch” same as above sem offset3 switch “se...

  • Page 889

    2.17 configuring batch measurement settings 2-879 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 reference level “sem offset1 reference level” value is described in 0.01 dbm u...

  • Page 890

    Chapter 2 scpi device message detail 2-880 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 rbw auto/manual “sem offset1 rbw switch” “auto”: auto “manual”: manual sem offset2 rbw auto/manual “sem offset2 rbw switch” ...

  • Page 891

    2.17 configuring batch measurement settings 2-881 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 integrate bw auto/manual “sem offset1 integrate bw switch” “auto”: auto “manua...

  • Page 892

    Chapter 2 scpi device message detail 2-882 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 vbw “sem offset1 vbw value” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “1khz”: 1 kh...

  • Page 893

    2.17 configuring batch measurement settings 2-883 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 sweeptime auto/manual “sem offset1 sweeptime switch” “auto”: auto “manual”: ma...

  • Page 894

    Chapter 2 scpi device message detail 2-884 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 detection “sem offset1 detection” “pos & neg”: pos & neg “positive”: positive “negative”: negative “sample”: sample “rms”: r...

  • Page 895

    2.17 configuring batch measurement settings 2-885 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 abs1 stop level “sem offset1 abs1 stop level” value is described in 0.01 dbm u...

  • Page 896

    Chapter 2 scpi device message detail 2-886 table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 rel start level “sem offset1 rel start level” value is described in 0.01 dbm units. Sem offset2 rel start level “sem offset2...

  • Page 897

    2.17 configuring batch measurement settings 2-887 2 sc pi d ev ice m es sa ge d et ail s table 2.17-7 parameter list settings (sem measurement) (cont’d) parameter attribute name setting attribute value setting sem offset1 fail logic “sem offset1 fail logic” “abs1”: abs1 “rel”: rel “abs1 and rel”: ab...

  • Page 898

    Chapter 2 scpi device message detail 2-888 :measure:batch:spurious[n]? [,] spurious emission batch measure function this command executes spurious emission measurement and outputs the measurement result after the parameters described in the specified parameter list file have been set. Query :measure...

  • Page 899

    2.17 configuring batch measurement settings 2-889 2 sc pi d ev ice m es sa ge d et ail s example of use to acquire the measurement result of spurious emission measurement using the myparam.Xls parameter list file (when result mode = a, spurious emission result type = worst) fetc:spur? "myparam.Xml" ...

  • Page 900

    Chapter 2 scpi device message detail 2-890 table 2.17-8 parameter list example (spurious emission measurement).

  • Page 901

    2.17 configuring batch measurement settings 2-891 2 sc pi d ev ice m es sa ge d et ail s table 2.17-8 parameter list example (spurious emission measurement) (cont’d).

  • Page 902

    Chapter 2 scpi device message detail 2-892 table 2.17-8 parameter list example (spurious emission measurement) (cont’d) describe the setting parameters in the part enclosed between the commonparams elements. The description method consists in describing the parameter name to be set in the name attri...

  • Page 903

    2.17 configuring batch measurement settings 2-893 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) parameter attribute name setting attribute value setting reference level “reference level” value is described in dbm units. Reference level of...

  • Page 904

    Chapter 2 scpi device message detail 2-894 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting pre-amp “pre-amp” “off”: off “on”: on vbw mode “vbw mode” “power”: power “video”: video obw method “obw method” “n%”: n% “...

  • Page 905

    2.17 configuring batch measurement settings 2-895 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 on/off “spurious segment switch1” “off”: off “on”: on spur...

  • Page 906

    Chapter 2 scpi device message detail 2-896 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 start freq “spurious start freq1” value is described in hz units. Spurious segment2 start freq “spurious...

  • Page 907

    2.17 configuring batch measurement settings 2-897 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 stop freq1 “spurious stop freq1” value is described in hz ...

  • Page 908

    Chapter 2 scpi device message detail 2-898 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 reference level “spurious reference level1” value is described in dbm units. Spurious segment2 reference...

  • Page 909

    2.17 configuring batch measurement settings 2-899 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 attenuator auto/manual “spurious attenuator switch1” “auto...

  • Page 910

    Chapter 2 scpi device message detail 2-900 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 attenuator “spurious attenuator1” value is described in db units. Spurious segment2 attenuator “spurious...

  • Page 911

    2.17 configuring batch measurement settings 2-901 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 rbw auto/manual “spurious rbw switch1” “auto”: auto “manua...

  • Page 912

    Chapter 2 scpi device message detail 2-902 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 rbw “spurious rbw1” “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “500hz”: 500 hz “1khz”: 1 khz “3khz”: ...

  • Page 913

    2.17 configuring batch measurement settings 2-903 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 rbw “spurious rbw11” “30hz”: 30 hz “100hz”: 100 hz “300hz...

  • Page 914

    Chapter 2 scpi device message detail 2-904 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 vbw auto/manual “spurious vbw switch1” “auto”: auto “manual”: manual spurious segment2 vbw auto/manual “...

  • Page 915

    2.17 configuring batch measurement settings 2-905 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 vbw “spurious vbw1” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz ...

  • Page 916

    Chapter 2 scpi device message detail 2-906 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 vbw “spurious vbw11” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 h...

  • Page 917

    2.17 configuring batch measurement settings 2-907 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 sweep time auto/manual “spurious sweep time switch1” “auto...

  • Page 918

    Chapter 2 scpi device message detail 2-908 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 sweep time “spurious sweep time1” value is described in ms units. Spurious segment2 sweep time “spurious...

  • Page 919

    2.17 configuring batch measurement settings 2-909 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 pause before sweep “spurious pause before sweep1” “off”: o...

  • Page 920

    Chapter 2 scpi device message detail 2-910 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 preamp “spurious preamp1” “off”: off “on”: on spurious segment2 preamp “spurious preamp2” same as above ...

  • Page 921

    2.17 configuring batch measurement settings 2-911 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 detection “spurious detection1” “pos & neg”: pos & neg “po...

  • Page 922

    Chapter 2 scpi device message detail 2-912 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 trace point “spurious trace point1” describes the number of trace points. Spurious segment2 trace point ...

  • Page 923

    2.17 configuring batch measurement settings 2-913 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 storage count “spurious storage count1” describes the stor...

  • Page 924

    Chapter 2 scpi device message detail 2-914 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 correction “spurious correction data type1” “default”: common to use a user defined correction value, de...

  • Page 925

    2.17 configuring batch measurement settings 2-915 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 limit start level “spurious limit start level1” value is d...

  • Page 926

    Chapter 2 scpi device message detail 2-916 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 limit stop level auto/manual “spurious limit stop level mode1” “auto”: auto “manual”: manual spurious se...

  • Page 927

    2.17 configuring batch measurement settings 2-917 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 limit stop level “spurious limit stop level1” value is des...

  • Page 928

    Chapter 2 scpi device message detail 2-918 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 search resolution “spurious search resolution1” value is described in 0.001 db units. Spurious segment2 ...

  • Page 929

    2.17 configuring batch measurement settings 2-919 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 search threshold level “spurious search threshold level1” ...

  • Page 930

    Chapter 2 scpi device message detail 2-920 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain couple segment rbw on/off “spurious couple segment rbw1” “on”: on “off”: off spurious segmen...

  • Page 931

    2.17 configuring batch measurement settings 2-921 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 time domain couple segment rbw on/off “spurious couple se...

  • Page 932

    Chapter 2 scpi device message detail 2-922 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain rbw “spurious time domain rbw1” “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “500hz”: 500 h...

  • Page 933

    2.17 configuring batch measurement settings 2-923 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 time domain rbw “spurious time domain rbw11” “30hz”: 30 h...

  • Page 934

    Chapter 2 scpi device message detail 2-924 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain couple segment vbw on/off “spurious couple segment vbw1” “on”: on “off”: off spurious segmen...

  • Page 935

    2.17 configuring batch measurement settings 2-925 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 time domain couple segment vbw on/off “spurious couple se...

  • Page 936

    Chapter 2 scpi device message detail 2-926 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain vbw “spurious time domain vbw1” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”:...

  • Page 937

    2.17 configuring batch measurement settings 2-927 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 time domain vbw “spurious time domain vbw11” “1hz”: 1 hz ...

  • Page 938

    Chapter 2 scpi device message detail 2-928 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain sweep time “spurious time domain sweep time1” value is described in µs units. Spurious segme...

  • Page 939

    2.17 configuring batch measurement settings 2-929 2 sc pi d ev ice m es sa ge d et ail s table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment1 time domain detection “spurious time domain detection1” “p...

  • Page 940

    Chapter 2 scpi device message detail 2-930 table 2.17-9 parameter list settings (spurious emission measurement) (cont’d) parameter attribute name setting attribute value setting spurious segment11 time domain detection “spurious time domain detection11” “pos & neg”: pos & neg “positive”: positive “n...

  • Page 941

    2.17 configuring batch measurement settings 2-931 2 sc pi d ev ice m es sa ge d et ail s :measure:batch:im? ,[,[,]] transmit intermodulation batch measure function this command executes transmit intermodulation measurement and outputs the result based on the specified parameter list file. Query :mea...

  • Page 942

    Chapter 2 scpi device message detail 2-932 drive name a,b,d,e,f,... D drive is used when omitted. Relative power of lower offset-n relative power of upper offset-n no suffix code, db unit, 0.001 db resolution –999.0 is returned when there is an error and no measurement is performed. Power of referen...

  • Page 943

    2.17 configuring batch measurement settings 2-933 2 sc pi d ev ice m es sa ge d et ail s parameter list format table 2.17-10 lists the parameter list example. Table 2.17-10 parameter list example (im measurement).

  • Page 944

    Chapter 2 scpi device message detail 2-934 table 2.17-10 parameter list example (im measurement) (cont’d).

  • Page 945

    2.17 configuring batch measurement settings 2-935 2 sc pi d ev ice m es sa ge d et ail s describe the setting parameters in the part enclosed between the commonparams elements. The description method consists in describing the parameter name to be set in the name attribute in the attribute element, ...

  • Page 946

    Chapter 2 scpi device message detail 2-936 table 2.17-11 parameter list settings (im measurement – sg settings) parameter attribute name setting attribute value setting package name “package name” describes the package name to use. Pattern name “pattern name” describes the pattern name to use. Modul...

  • Page 947

    2.17 configuring batch measurement settings 2-937 2 sc pi d ev ice m es sa ge d et ail s table 2.17-12 parameter list settings (im measurement – acp settings) parameter attribute name setting attribute value setting center frequency “center freq.” value is described in hz units. Spurious mode “frequ...

  • Page 948

    Chapter 2 scpi device message detail 2-938 table 2.17-12 parameter list settings (im measurement – acp settings) (cont’d) parameter attribute name setting attribute value setting vbw “vbw value” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “1khz”: 1 khz “3khz”:...

  • Page 949

    2.17 configuring batch measurement settings 2-939 2 sc pi d ev ice m es sa ge d et ail s table 2.17-12 parameter list settings (im measurement – acp settings) (cont’d) parameter attribute name setting attribute value setting trigger switch “trigger switch” “off”: off “on”: on trigger source “trigger...

  • Page 950

    Chapter 2 scpi device message detail 2-940 table 2.17-12 parameter list settings (im measurement – acp settings) (cont’d) parameter attribute name setting attribute value setting acp carrier select number “acp carrier select number” describes reference carrier number. Acp in band center “acp in band...

  • Page 951

    2.17 configuring batch measurement settings 2-941 2 sc pi d ev ice m es sa ge d et ail s table 2.17-13 parameter list settings (im measurement – spa settings) parameter attribute name setting attribute value setting relative frequency “relative freq.” when this parameter is used, the relative freque...

  • Page 952

    Chapter 2 scpi device message detail 2-942 table 2.17-13 parameter list settings (im measurement – spa settings) (cont’d) parameter attribute name setting attribute value setting vbw “vbw value time domain” “1hz”: 1 hz “3hz”: 3 hz “10hz”: 10 hz “30hz”: 30 hz “100hz”: 100 hz “300hz”: 300 hz “1khz”: 1...

  • Page 953

    2.17 configuring batch measurement settings 2-943 2 sc pi d ev ice m es sa ge d et ail s table 2.17-13 parameter list settings (im measurement – spa settings) (cont’d) parameter attribute name setting attribute value setting trigger switch “trigger switch” “off”: off “on”: on trigger source “trigger...

  • Page 954

    Chapter 2 scpi device message detail 2-944 :measure:powadj? ,,,,,[,ncy>[,[,[,[,]]]]] measure power adjust function this command executes power adjustment and reads the result. Power adjustment combines the sg option and power measurement functions to set the output level of the dut, such as an ampli...

  • Page 955

    2.17 configuring batch measurement settings 2-945 2 sc pi d ev ice m es sa ge d et ail s set the sg output level set at the start. When inserting a dut, specify the dut input level and rf input so the maximum input level is not exceeded. Range [ms269xa] – 140 dbm to – 5 dbm [ms2830a], [ms2840a] –40....

  • Page 956

    Chapter 2 scpi device message detail 2-946 250 khz to 6 ghz (option 041, and 021/121) resolution 1 hz suffix code hz, khz, kz, mhz, mz, ghz, gz hz is used when omitted. Maximum, minimum, and default cannot be used. The currently set frequency cannot be used when omitted. Trace point 11 11 point 21 2...

  • Page 957

    2.17 configuring batch measurement settings 2-947 2 sc pi d ev ice m es sa ge d et ail s power adjustment time suffix code none, ms (unit) –999.0 is returned if there is no measurement. Dut output level at power adjustment added to response when log output on suffix code none, dbm (unit) 0.01 db (re...

  • Page 958

    Chapter 2 scpi device message detail 2-948 number, it is rounded up to the nearest even number (example: 35 db →36 db). After executing this command, the function and the following settings specified by an argument are changed. ● sets detection to rms ● sets sweep mode to single ● sets scale mode to...

  • Page 959: 2.18 Other Settings

    2.18 other settings 2-949 2 sc pi d ev ice m es sa ge d et ail s 2.18 other settings table 2.18-1 lists device messages for other settings. Table 2.18-1 device messages for other settings function device message measurement status query :status:error? Uncal status query :status:uncal? Erase warm up ...

  • Page 960

    Chapter 2 scpi device message detail 2-950 :status:error? Measurement status query function this command queries the measurement status. Query :status:error? Response parameter measurement status value = bit0 + bit1 + bit2 + bit3 + bit4 + bit5 + bit6 + bit7 + bit8 + bit9 + bit10 + bit11 + bit12 + bi...

  • Page 961

    2.18 other settings 2-951 2 sc pi d ev ice m es sa ge d et ail s :status:uncal? Uncal status query function this command queries uncal status. Query :status:uncal? Response parameter uncal status norm normal unc uncal example of use to query uncal status. Stat:unc? > norm :display:annotation:wup:era...

  • Page 964

    Chapter 2 scpi device message detail 2-954 :display:annotation:title:data title entry function this command registers the title character string. Command :display:annotation:title:data parameter character string within 32 characters enclosed by double quotation marks (" ") or single quotation marks ...

  • Page 965

    2.18 other settings 2-955 2 sc pi d ev ice m es sa ge d et ail s example of use to query the title character string. Disp:ann:titl:data? > spectrum analyzer related command this command has the same function as the following command. :display:acpower:annotation:title:data :calibration:ytf pre-select...

  • Page 966

    Chapter 2 scpi device message detail 2-956 :calibration:ytf? Pre-selector auto tune query function this command queries the pre-selector settings. Query :calibration:ytf? Response parameter normal/error 0 finished normal 1 error details [ms269xa], [ms2830a], [ms2840a] this command is not available d...

  • Page 967

    2.18 other settings 2-957 2 sc pi d ev ice m es sa ge d et ail s [:sense]:power[:rf]:padjust pre-selector tune function this command sets the preselector peaking bias value. Command [:sense]:power[:rf]:padjust parameter peaking bias value range –128 to 127 resolution 1 default 0 details [ms269xa] au...

  • Page 968

    Chapter 2 scpi device message detail 2-958 [:sense]:power[:rf]:padjust? Pre-selector tune query function this command queries the preselector peaking bias value. Query [:sense]:power[:rf]:padjust? Response parameter peaking bias value range –128 to 127 resolution 1 details [ms269xa] automatic settin...

  • Page 969

    2.18 other settings 2-959 2 sc pi d ev ice m es sa ge d et ail s :calibration:rclock[:value] adjust reference clock function this command sets the adjustment value for the internal reference signal oscillator (reference clock). Command :calibration:rclock[:value] parameter adjustment value range 0 t...

  • Page 970

    Chapter 2 scpi device message detail 2-960 :calibration:rclock[:value]:preset adjust reference clock preset function this command resets the adjustment value of the internal reference signal oscillator (reference clock). Command :calibration:rclock[:value]:preset example of use to reset the adjustme...

  • Page 971

    2.18 other settings 2-961 2 sc pi d ev ice m es sa ge d et ail s [:sense]:power[:rf]:mw:preselector[:state]? Micro wave preselector bypass query function this command queries the micro wave preselector bypass. Query [:sense]:power[:rf]:mw:preselector[:state]? Response parameter microwave preselector...

  • Page 972

    Chapter 2 scpi device message detail 2-962 2.19 questionable status register the figure below shows the layer structure of the questionable status register. Voltage (not used) db0 current (not used) db1 time (not used) db2 power (not used) db3 temperature (not used) db4 frequency (not used) db5 phas...

  • Page 973

    2.19 questionable status register 2-963 2 sc pi d ev ice m es sa ge d et ail s table 2.19-3 lists device messages for the questionable status register. Table 2.19-3 device messages for questionable status register function device message questionable status register event :status:questionable[:event...

  • Page 974

    Chapter 2 scpi device message detail 2-964 :status:questionable[:event]? Questionable status register event function this command queries the event register of the questionable status register. Query :status:questionable[:event]? Response parameter total bytes of event register resolution 1 range 0 ...

  • Page 975

    2.19 questionable status register 2-965 2 sc pi d ev ice m es sa ge d et ail s :status:questionable:condition? Questionable status register condition function this command queries the condition register of the questionable status register. Query :status:questionable:condition? Response parameter tot...

  • Page 976

    Chapter 2 scpi device message detail 2-966 :status:questionable:enable questionable status register enable function this command sets the event enable register of the questionable status register. Command :status:questionable:enable parameter total byte of event enable register resolution 1 range 0 ...

  • Page 977

    2.19 questionable status register 2-967 2 sc pi d ev ice m es sa ge d et ail s :status:questionable:enable? Questionable status register enable query function this command queries the event enable register of the questionable status register. Query :status:questionable:enable? Response parameter tot...

  • Page 978

    Chapter 2 scpi device message detail 2-968 :status:questionable:ntransition questionable status register negative transition function this command sets the transition filter (negative direction change) of the questionable status register. Command :status:questionable:ntransition parameter total byte...

  • Page 979

    2.19 questionable status register 2-969 2 sc pi d ev ice m es sa ge d et ail s example of use to query the transition filter (negative direction change) of the questionable status register. Stat:ques:ntr? > 16 :status:questionable:ptransition questionable status register positive transition function...

  • Page 980

    Chapter 2 scpi device message detail 2-970 :status:questionable:ptransition? Questionable status register positive transition query function this command queries the transition filter (positive direction change) of the questionable status register. Query :status:questionable:ptransition? Response pa...

  • Page 981

    2.19 questionable status register 2-971 2 sc pi d ev ice m es sa ge d et ail s :status:questionable:measure[:event]? Questionable measure register event function this command queries the event register of the questionable measure register. Query :status:questionable:measure[:event]? Response paramet...

  • Page 982

    Chapter 2 scpi device message detail 2-972 example of use to query the contents of the condition register of the questionable measure register. Stat:ques:meas:cond? > 0 :status:questionable:measure:enable questionable measure register enable function this command sets the event enable register of th...

  • Page 983

    2.19 questionable status register 2-973 2 sc pi d ev ice m es sa ge d et ail s :status:questionable:measure:enable? Questionable measure register enable query function this command queries the event enable register of the questionable measure register. Query :status:questionable:measure:enable? Resp...

  • Page 984

    Chapter 2 scpi device message detail 2-974 :status:questionable:measure:ntransition questionable measure register negative transition function this command sets the transition filter (negative direction change) of the questionable measure register. Command :status:questionable:measure:ntransition pa...

  • Page 985

    2.19 questionable status register 2-975 2 sc pi d ev ice m es sa ge d et ail s example of use to query the transition filter (negative direction change) of the questionable measure register. Stat:ques:meas:ntr? > 16 :status:questionable:measure:ptransition questionable measure register positive tran...

  • Page 986

    Chapter 2 scpi device message detail 2-976 :status:questionable:measure:ptransition? Questionable measure register positive transition query function this command queries the transition filter (positive direction change) of the questionable measure register. Query :status:questionable:measure:ptrans...

  • Page 987

    2.20 operation status register 2-977 2 sc pi d ev ice m es sa ge d et ail s 2.20 operation status register the figure below shows the layer structure of the operation status register. Calibrating db0 settling db1 ranging (not used) db2 sweeping db3 measuring（not used） db4 wainting for trig db5 waiti...

  • Page 988

    Chapter 2 scpi device message detail 2-978 the table below shows device messages for the operation status register. Table 2.20-2 device messages for operation status register function device message operation status register event :status:operation[:event]? Operation status register condition :statu...

  • Page 989

    2.20 operation status register 2-979 2 sc pi d ev ice m es sa ge d et ail s :status:operation[:event]? Operation status register event function this command queries the event register of the operation status register. Query :status:operation[:event]? Response parameter total byte of event register r...

  • Page 990

    Chapter 2 scpi device message detail 2-980 :status:operation:condition? Operation status register condition function this command queries the condition register of the operation status register. Query :status:operation:condition? Response parameter total byte of condition register resolution 1 range...

  • Page 991

    2.20 operation status register 2-981 2 sc pi d ev ice m es sa ge d et ail s :status:operation:enable operation status register enable function this command sets the event enable register of the operation status register. Command :status:operation:enable parameter total byte of event enable register ...

  • Page 992

    Chapter 2 scpi device message detail 2-982 example of use to query the event enable register of the operation status register. Stat:oper:enab? > 16 :status:operation:ntransition operation status register negative transition function this command sets the transition filter (negative direction change)...

  • Page 993

    2.20 operation status register 2-983 2 sc pi d ev ice m es sa ge d et ail s :status:operation:ntransition? Operation status register negative transition query function this command queries the transition filter (negative direction change) of the operation status register. Query :status:operation:ntr...

  • Page 994

    Chapter 2 scpi device message detail 2-984 :status:operation:ptransition operation status register positive transition function this command sets the transition filter (positive direction change) of the operation status register. Command :status:operation:ptransition parameter total byte of transiti...

  • Page 995

    2.20 operation status register 2-985 2 sc pi d ev ice m es sa ge d et ail s :status:operation:ptransition? Operation status register positive transition query function this command queries the transition filter (positive direction change) of the operation status register. Query :status:operation:ptr...

  • Page 999

    2.21 setting external mixer 2-989 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer[:harmonic]:band? External mixer band query function this command queries the current external mixer band. Query [:sense]:mixer[:harmonic]:band? Response parameter external mixer band vhp high performance waveguid...

  • Page 1000

    Chapter 2 scpi device message detail 2-990 [:sense]:mixer:bias external mixer bias function this command sets the external mixer's bias current. Command [:sense]:mixer:bias parameter external mixer's bias current range 0.0 to 20.0 ma resolution 0.1 ma suffix code na,ua,ma,a ma is used when omitted. ...

  • Page 1001

    2.21 setting external mixer 2-991 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:bias? External mixer bias query function this command queries the current external mixer's bias current. Query [:sense]:mixer:bias? Response parameter external mixer's bias current range 0.1 to 20.0 ma resolution...

  • Page 1002

    Chapter 2 scpi device message detail 2-992 [:sense]:mixer:cable:loss external mixer cable loss value function this command sets the external mixer cable loss value. Command [:sense]:mixer:cable:loss parameter external mixer cable loss range 0.00 to 99.99 db resolution 0.01 db suffix code db db is us...

  • Page 1003

    2.21 setting external mixer 2-993 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:cable:loss? External mixer cable loss value query function this command queries the external mixer cable loss value. Query [:sense]:mixer:cable:loss? Response parameter external mixer cable loss range 0.00 to 99....

  • Page 1005

    2.21 setting external mixer 2-995 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:loss:mode? External mixer conversion loss mode query function this command queries the conversion loss mode of the external mixer in the current band. Query [:sense]:mixer:loss:mode? Response parameter conversion...

  • Page 1006

    Chapter 2 scpi device message detail 2-996 [:sense]:mixer:loss[:fixed] external mixer conversion loss fixed value function this command sets the external mixer's fixed conversion loss. Command [:sense]:mixer:loss[:fixed] parameter conversion loss of external mixer range 0.00 to 99.99 db resolution 0...

  • Page 1007

    2.21 setting external mixer 2-997 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:loss[:fixed]? External mixer conversion loss fixed value query function this command queries the external mixer's fixed conversion loss. Query [:sense]:mixer:loss[:fixed]? Response parameter conversion loss of ex...

  • Page 1008

    Chapter 2 scpi device message detail 2-998 [:sense]:mixer:loss:table external mixer conversion loss table function this command loads the conversion loss table of the external mixer from the usb memory stick. Command [:sense]:mixer:loss:table details this function is available when option 044/045 is...

  • Page 1009

    2.21 setting external mixer 2-999 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:loss:table:serial? External mixer conversion loss table serial number query function this command queries the serial number of the external mixer conversion loss table. Query [:sense]:mixer:loss:table:serial? Res...

  • Page 1011

    2.21 setting external mixer 2-1001 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:ps[:center]? Ps function query function this command queries the state of ps function, which reverses the frequency polarity at the center frequency when using high performance waveguide mixer. Query [:sense]:mi...

  • Page 1013

    2.21 setting external mixer 2-1003 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:signal? Signal identifier query function this command queries the state of signal identifier operation, which identifies measured signal and image signal when external mixer is used. Query [:sense]:mixer:signal?...

  • Page 1015

    2.21 setting external mixer 2-1005 2 sc pi d ev ice m es sa ge d et ail s [:sense]:mixer:signal:mode? Signal identifier mode query function this command queries the type of signal identifier operation, which identifies measured signal and image signal when external mixer is used. Query [:sense]:mixe...

  • Page 1016

    Chapter 2 scpi device message detail 2-1006 [:sense]:mixer:calibration external mixer calibration function this command executes the external mixer calibration function command [:sense]:mixer:calibration details this function is available only when ms2830a is installed with option 044/045 and combin...

  • Page 1019

    2.22 setting save on event 2-1009 2 sc pi d ev ice m es sa ge d et ail s :mmemory:store:event? Event mode query function this command queries the setting of the save on event function. Query :mmemory:store:event? Response parameter save on event function 1 the save on event function is set to on. 0 ...

  • Page 1021

    2.22 setting save on event 2-1011 2 sc pi d ev ice m es sa ge d et ail s :mmemory:store:event:type? Event type query function this command queries the setting of the event type that triggers the save on the event function. Query :mmemory:store:event:type? Response parameter event type lfa saves a wa...

  • Page 1023

    2.22 setting save on event 2-1013 2 sc pi d ev ice m es sa ge d et ail s :mmemory:store:event:stop? Save then stop query function this command queries the on/off setting of the save then stop function that stops the file save operation once a file is saved by the save on the event function. Query :m...

  • Page 1026

    Chapter 2 scpi device message details 2-1016. [:sense]:correction:noise:floor? Noise floor reduction query function this command queries the on/off state of the noise floor reduction function. Query [:sense]:correction:noise:floor? Response parameter noise floor reduction on/off state 1 noise floor ...

  • Page 1027

    Chapter 3 native device message list 3-1 3 n ati ve d ev ice m es sa ge list this chapter describes remote control commands for executing the spectrum analyzer function (hereinafter referred to as “this application”) using a list organized by functions. Refer to chapter 4 “native device message deta...

  • Page 1028

    Chapter ３ native device message details 3-2 3.12 reference signal settings .......................................... 3-54 3.13 other settings ............................................................. 3-55 3.14 setting external mixer ................................................. 3-56.

  • Page 1029

    3.1 ie e e 488. 2 c om m on d ev ic e m es sag es 3-3 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.1 ieee488.2 common device messages ieee488.2 common device messages available in this application are shown in table 3.1-1. Table 3.1-1 ieee488.2 common device messages funct...

  • Page 1030

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-4 table 3.1-1 ieee488.2 common device messages (cont’d) function command query response remarks standard event status enable register *ese byte *ese? Byte byte = bit7: power on bit6: user request bit5: command error bit4: execution error bit3: device...

  • Page 1031

    3.2 a pp lica tio n c om m on de vi ce m es sa ge s 3-5 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.2 application common device messages application common device messages available in this application are shown in table 3.2-1. Table 3.2-1 application common device messag...

  • Page 1033

    3.3 fr eq ue nc y/s pa n s ett in gs 3-7 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.3 frequency/span settings device messages for setting frequency and span are shown in table 3.3-1. Table 3.3-1 frequency setting messages function command query response remarks center fr...

  • Page 1034: 3.4  Level Settings

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-8 3.4 level settings device messages for setting the level are shown in table 3.4-1. Table 3.4-1 level setting messages function command query response remarks reference level rlv level rlv? Level reference level rl level rl? Level attenuator at att ...

  • Page 1035: 3.5  Rbw/vbw Settings

    3.5 r bw /vb w s ett in gs 3-9 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.5 rbw/vbw settings device messages for setting rbw/vbw are shown in table 3.5-1. Table 3.5-1 rbw/vbw setting messages function command query response remarks resolution bandwidth (rbw) rb bandwidth...

  • Page 1036: 3.6  Marker Settings

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-10 3.6 marker settings device messages for setting the marker are shown in table 3.6-1. Table 3.6-1 marker setting messages function command query response remarks marker mode mkr mode_com,marker mkr? Marker mode_res mode_com: marker mode marker: mar...

  • Page 1037

    3.6 m ar ke r s ett in gs 3-11 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.6-1 marker setting messages (cont’d) function command query response remarks power marker powermarker on_off_com powermarker? On_off_res marker to center frequency mkcf --- --- marker to refe...

  • Page 1038

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-12 table 3.6-1 marker setting messages (cont’d) function command query response remarks active marker mkact marker mkact? Marker relative to calc:mark:ref marker,integer calc:mark:ref? Marker integer marker list calc:mark:tabl switch_com calc:mark:ta...

  • Page 1039

    3.7 sig na l s ear ch s ett in gs 3-13 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.7 signal search settings device messages for setting signal search are shown in table 3.7-1. Table 3.7-1 signal search setting messages function command query response remarks peak search m...

  • Page 1040

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-14 table 3.7-1 signal search setting messages (cont’d) function command query response remarks marker readout query --- calc:mark:read? Freq_1,power_1,...,f req_10,power_10 (frequency domain) time_1,power_1,...,t ime_10,power_10 (time domain).

  • Page 1041: 3.8  Trace Settings

    3.8 tr ac e s ett in gs 3-15 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.8 trace settings table 3.8-1 lists device messages for setting trace. Table 3.8-1 trace setting messages function command query response remarks active trace mktrace trace mktrace? Trace trace: trace...

  • Page 1042

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-16 table 3.8-1 trace setting messages (cont’d) function command query response remarks write and query trace data (trace a) xma wpoint,data xma? Start,number data1,data2,... Wpoint: data writing position start: readout starting position number: data ...

  • Page 1044

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-18 3.9 sweep/trigger/gate settings device messages for setting sweep/trigger/gate are shown in table 3.9-1. Table 3.9-1 sweep/trigger/gate setting messages function command query response remarks single sweep sngls --- --- (asynchronous sweep) swp sw...

  • Page 1049

    3. 10 m ea su re f un cti on s ett in gs 3-23 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.10 measure function settings 3.10.1 common measure function settings device messages common for measure functions are shown in table 3.10.1-1. Table 3.10.1-1 common measure function ...

  • Page 1050

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-24 3.10.2 adjacent channel power measurement function settings device messages for adjacent channel power measurement settings are shown in table 3.10.2-1. Table 3.10.2-1 adjacent channel power measurement function setting messages function command q...

  • Page 1051

    3. 10 m ea su re f un cti on s ett in gs 3-25 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.2-1 adjacent channel power measurement function setting messages (cont’d) function command query response remarks acp offset frequency 1 adjchsp freq adjchsp? Freq freq: off...

  • Page 1052

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-26 table 3.10.2-1 adjacent channel power measurement setting messages (cont’d) function command query response remarks acp measurement result query --- res? Lc,lr1,la1,ur1,ua1,l r2,la2,ur2,ua2,lr3,l a3,ur3,ua3 lc: reference power absolute value lr1: ...

  • Page 1053

    3. 10 m ea su re f un cti on s ett in gs 3-27 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.2-1 adjacent channel power measurement setting messages (cont’d) function command query response remarks acp measurement result query (cont’d) --- res? Carrier ls,lca,lc1,lc...

  • Page 1054

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-28 3.10.3 burst average power measurement function settings device messages for burst average power measurement settings are shown in table 3.10.3-1. Table 3.10.3-1 burst average power measurement function setting messages function command query resp...

  • Page 1055

    3. 10 m ea su re f un cti on s ett in gs 3-29 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.10.4 channel power measurement function settings device messages for channel power measurement settings are shown in table 3.10.4-1. Table 3.10.4-1 channel power measurement function...

  • Page 1056

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-30 3.10.5 occupied bandwidth measurement function settings device messages for occupied bandwidth measurement settings are shown in table 3.10.5-1. Table 3.10.5-1 occupied bandwidth measurement function setting messages function command query respons...

  • Page 1057

    3. 10 m ea su re f un cti on s ett in gs 3-31 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.10.6 spectrum emission mask measurement function settings device messages for spectrum emission mask measurement settings are shown in table 3.10.6-1. Table 3.10.6-1 spectrum emissio...

  • Page 1058

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-32 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask sweep type select rules real fft width query --- sem:swe:rul:fft:rwid ? Freq spectrum emission mask...

  • Page 1059

    3. 10 m ea su re f un cti on s ett in gs 3-33 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset resolution bandwidth sem:offs...

  • Page 1060

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-34 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset integrate bandwidth sem:offs:list:band:in t bandwidth_1[,bandwidt h_2[,bandwidth_3[,ban dwid...

  • Page 1061

    3. 10 m ea su re f un cti on s ett in gs 3-35 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset video bandwidth auto/manual s...

  • Page 1062

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-36 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset start frequency sem:offs:list:freq:st ar freq_1[,freq_2[,freq_ 3[,freq_4[,freq_5[,fr eq_6[,f...

  • Page 1063

    3. 10 m ea su re f un cti on s ett in gs 3-37 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset start frequency absolute limi...

  • Page 1064

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-38 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset stop frequency absolute limit level sem:offs:list:stop:ab s integer,ampl_1[,ampl_ 2[,ampl_3[...

  • Page 1065

    3. 10 m ea su re f un cti on s ett in gs 3-39 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask offset sweep time auto/manual sem:of...

  • Page 1066

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-40 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask limit side sem:offs:side side sem:offs:side? Side spectrum emission mask trace point sem:swe:poin i...

  • Page 1067

    3. 10 m ea su re f un cti on s ett in gs 3-41 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask fetch --- fetc:sem? N total_judge,re...

  • Page 1068

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-42 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask fetch --- fetc:sem? N -999.0,ref_power,-999.0,-999.0,0, -999.0,-999.0,-999.0,-999.0,-999. 0, -999.0...

  • Page 1069

    3. 10 m ea su re f un cti on s ett in gs 3-43 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask fetch --- fetc:sem? N -999.0,-999.0,...

  • Page 1070

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-44 table 3.10.6-1 spectrum emission mask measurement function setting messages (cont’d) function command query response remarks spectrum emission mask fetch --- fetc:sem? N total_judge,ref_power, abs_lower_offset_1,abs_upper_offs et_1, margin_lower_o...

  • Page 1071

    3. 10 m ea su re f un cti on s ett in gs 3-45 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 3.10.7 spurious emission measurement function settings table 3.10.7-1 lists device messages for setting the spurious emission measurement functions. Table 3.10.7-1 spurious emission me...

  • Page 1073

    3. 10 m ea su re f un cti on s ett in gs 3-47 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.7-1 spurious emission measurement function setting messages (cont’d) function command query response remarks spurious emission resolution bandwidth auto/manual spur:band:aut...

  • Page 1074

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-48 table 3.10.7-1 spurious emission measurement function setting messages (cont’d) function command query response remarks spurious emission detection mode spur:det mode_n spur:det? Mode_n n :1 to 20 spurious emission trace point spur:swe:poin intege...

  • Page 1075

    3. 10 m ea su re f un cti on s ett in gs 3-49 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.7-1 spurious emission measurement function setting messages (cont’d) function command query response remarks spurious emission limit stop level calc:spur:lim:abs:da ta:stop ...

  • Page 1076

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-50 table 3.10.7-1 spurious emission measurement function setting messages (cont’d) function command query response remarks spurious emission time domain sweep time spur:tdom:swe:time seconds_n spur:tdom:swe:time? Seconds_n n :1 to 20 spurious emissio...

  • Page 1077

    3. 10 m ea su re f un cti on s ett in gs 3-51 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.10.7-1 spurious emission measurement function setting messages (cont’d) function command query response remarks spurious emission fetch --- fetc:spur? N when result mode is set...

  • Page 1078

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-52 3.11 batch measure function settings table 3.11-1 lists device messages for setting the batch measurement function. Table 3.11-1 batch measure function settings function command query response remarks reloading parameter list files mmem:rel:batc d...

  • Page 1079

    3.11 b atc h m ea su re f un cti on s ett in gs 3-53 nat ive d evic e m essa ge l ist 3 nat ive d evic e m essa ge l ist 3 table 3.11-1 batch measure function settings (cont’d) function command query response remarks transmit intermodulation batch measure --- meas:batc:im? Filename,spa_freq,[sg_fr e...

  • Page 1080

    C ha pte r ３ n ati ve d ev ice m es sa ge l ist 3-54 3.12 reference signal settings device messages for setting reference signal are shown in table 3.12-1. Table 3.12-1 reference signal setting messages function command query response remarks adjust reference clock cal:rcl integer cal:rcl? Integer i...

  • Page 1083

    Chapter 4 native device message details 4-1 4 n ati ve d ev ice m es sa ge d et ail s this chapter describes detailed specifications on remote control commands for executing functions of this application in alphabetical order. Refer to the ms2690a/ms2691a/ms2692a and ms2830a/ms2840a signal analyzer ...

  • Page 1084

    Chapter ４ native device message details 4-2 cal:rcl:pres .................................................................... 4-36 calc:mark:aoff............................................................... 4-37 calc:mark:coup:zone/ calc:mark:coup:zone? ... 4-38 calc:mark:fco/calc:mark:fco? .........

  • Page 1085

    Chapter ４ native device message details 4-3 4 n ati ve d ev ice m es sa ge d et ail s disp:spur:segm:mode/disp:spur:segm:mode? ..... 4-77 disp:spur:segm:next .................................................... 4-78 disp:spur:segm:prev .................................................... 4-78 disp:s...

  • Page 1086

    Chapter ４ native device message details 4-4 meas:batc:acp? ............................................................. 4-143 meas:batc:im? ................................................................ 4-144 meas:batc:obw? ............................................................ 4-147 meas:b...

  • Page 1087

    Chapter ４ native device message details 4-5 4 n ati ve d ev ice m es sa ge d et ail s rfat/rfat? ...................................................................... 4-201 rl/rl? ................................................................................ 4-202 rlv/rlv? ..........................

  • Page 1088

    Chapter ４ native device message details 4-6 sem:offs:list:rlev/sem:offs:list:rlev? .............. 4-239 sem:offs:list:rlev:auto/sem:offs:list:rlev: auto? ...................................................................... 4-240 sem:offs:list:star:abs/sem:offs:list:star: abs? ........................

  • Page 1089

    Chapter ４ native device message details 4-7 4 n ati ve d ev ice m es sa ge d et ail s spur:att/spur:att? ..................................................... 4-276 spur:aver:coun/spur:aver:coun? ........................ 4-277 spur:aver:coun:coup/spur:aver:coun:coup? . 4-278 spur:band/spur:band? ......

  • Page 1090

    Chapter ４ native device message details 4-8 swe:egat:view:band:auto/swe:egat:view:band: auto? ...................................................................... 4-325 swe:egat:view:band:vid/swe:egat:view:band: vid? .......................................................................... 4-326 ...

  • Page 1091

    Chapter ４ native device message details 4-9 4 n ati ve d ev ice m es sa ge d et ail s xmb/xmb? .......................................................................... 4-361 xmc/xmc? ......................................................................... 4-362 xmd/xmd? .............................

  • Page 1092

    Chapter ４ native device message details 4-10 activetrace/activetrace? Active trace function this command selects the trace (active trace) that operates the marker. Command activetrace trace query activetrace? Response trace parameter trace trace type to be activated tra trace a trb trace b trc trace...

  • Page 1093

    Chapter ４ native device message details 4-11 4 n ati ve d ev ice m es sa ge d et ail s adjcarriercnt/adjcarriercnt? Acp in band center function this command sets the in band center frequency for acp measurement. Command adjcarriercnt freq query adjcarriercnt? Response freq suffix code none. Value is...

  • Page 1094

    Chapter ４ native device message details 4-12 adjcarriernum/adjcarriernum? Acp carrier number function this command sets the carrier number for acp measurement. Command adjcarriernum n query adjcarriernum? Response n suffix code none parameter n carrier number range 1 to 12 resolution 1 suffix code n...

  • Page 1095

    Chapter ４ native device message details 4-13 4 n ati ve d ev ice m es sa ge d et ail s adjcarrierspac/adjcarrierspac? Acp carrier spacing function this command sets the frequency interval among carriers for acp measurement. Command adjcarrierspac freq query adjcarrierspac? Response freq suffix code ...

  • Page 1096

    Chapter ４ native device message details 4-14 adjchbw/adjchbw? Acp offset ch bw function this command sets the offset channel bandwidth for acp measurement. Command adjchbw freq query adjchbw? Response freq suffix code none. Value is returned in hz units. Parameter freq offset channel bandwidth range...

  • Page 1097

    Chapter ４ native device message details 4-15 4 n ati ve d ev ice m es sa ge d et ail s adjchsp/adjchsp? Acp offset frequency acp offset-1 frequency function this command sets the offset frequency for offset channel 1 or the specified offset channel for acp measurement. Command adjchsp freq adjchsp o...

  • Page 1098

    Chapter ４ native device message details 4-16 adjchspf/adjchspf? Acp offset-2 frequency function this command sets the offset frequency of offset channel 2 for acp measurement. Command adjchspf freq query adjchspf? Response freq suffix code none. Value is returned in hz units. Parameter freq offset f...

  • Page 1099

    Chapter ４ native device message details 4-17 4 n ati ve d ev ice m es sa ge d et ail s adjchspff/adjchspff? Acp offset-3 frequency function this command sets the offset frequency of offset channel 3 for acp measurement. Command adjchspff freq query adjchspff? Response freq suffix code none. Value is...

  • Page 1100

    Chapter ４ native device message details 4-18 adjfiltertype/adjfiltertype? Acp filter type function this command selects filter type for acp measurement. Command adjfiltertype type,target query adjfiltertype? Target response type type, type (when target is omitted: the former indicates the offset cha...

  • Page 1101

    Chapter ４ native device message details 4-19 4 n ati ve d ev ice m es sa ge d et ail s adjinbw/adjinbw? Acp carrier bw function this command sets the carrier measurement bandwidth for acp measurement. Command adjinbw freq query adjinbw? Response freq suffix code none. Value is returned in hz units. ...

  • Page 1102

    Chapter ４ native device message details 4-20 adjoffset1/adjoffset1? Acp offset-1 function this command sets measurement channel 1 on/off for acp measurement. Command adjoffset1 on_off query adjoffset1? Response on_off parameter on_off measurement channel 1 on/off on measures measurement channel 1. O...

  • Page 1103

    Chapter ４ native device message details 4-21 4 n ati ve d ev ice m es sa ge d et ail s adjoffset2/adjoffset2? Acp offset-2 function this command sets measurement channel 2 on/off for acp measurement. Command adjoffset2 on_off query adjoffset2? Response on_off parameter on_off measurement channel 2 o...

  • Page 1104

    Chapter ４ native device message details 4-22 adjoffset3/adjoffset3? Acp offset-3 function this command sets measurement channel 3 on/off for acp measurement. Command adjoffset3 on_off query adjoffset3? Response on_off parameter on_off measurement channel 3 on/off on measures measurement channel 3. O...

  • Page 1105

    Chapter ４ native device message details 4-23 4 n ati ve d ev ice m es sa ge d et ail s adjpwrtype/adjpwrtype? Acp power result type function this command switches the result display type for acp measurement. Command adjpwrtype mode query adjpwrtype? Response mode parameter mode result display type c...

  • Page 1106

    Chapter ４ native device message details 4-24 adjrof/adjrof? Acp rolloff ratio function this command sets the rolloff ratio of the in band filter and/or offset channel filter for acp measurement. Command adjrof ratio,target query adjrof? Target response ratio ratio,ratio (when target is omitted: the ...

  • Page 1107

    Chapter ４ native device message details 4-25 4 n ati ve d ev ice m es sa ge d et ail s allmkpk? All peak search and query function this command queries all peak point frequencies (time) and levels contained in the trace data displayed in batch. Query allmkpk? Response freq1,level1,freq2,level2,... (...

  • Page 1108

    Chapter ４ native device message details 4-26 amd/amd? Storage mode (trace a) function this command selects trace a storage mode. Command amd mode query amd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear average example of use to set trace a storage mode to ...

  • Page 1109

    Chapter ４ native device message details 4-27 4 n ati ve d ev ice m es sa ge d et ail s at/at? Rf attenuator function this command sets the rf attenuator. Command at att at action query at? Response att parameter att attenuator value range 0 to 60 db resolution [ms269xa] 2 db [ms2830a], [ms2840a] 2 d...

  • Page 1110

    Chapter ４ native device message details 4-28 aunits/aunits? Log scale unit function this command sets the level display unit system at log scale. Command aunits unit query aunits? Response unit parameter unit level display unit system at log scale dbm dbm dbuv dbµv dbmv dbmv dbuve dbmv (emf) v v w w...

  • Page 1111

    Chapter ４ native device message details 4-29 4 n ati ve d ev ice m es sa ge d et ail s band:mode/band:mode? Resolution bandwidth normal/cispr function this command switches the resolution bandwidth mode. When couple time/freq. Domain is set to off, each parameter is specified in accordance with the ...

  • Page 1112

    Chapter ４ native device message details 4-30 bapwrstart/bapwrstart? Burst average power start time function this command sets the start position (time) of burst average power measurement. Command bapwrstart time query bapwrstart? Response time suffix code none. Value is returned in µs units. Paramet...

  • Page 1113

    Chapter ４ native device message details 4-31 4 n ati ve d ev ice m es sa ge d et ail s bapwrstop/bapwrstop? Burst average power stop time function this command sets the stop position (time) of burst average power measurement. Command bapwrstop time query bapwrstop? Response time suffix code none. Va...

  • Page 1114

    Chapter ４ native device message details 4-32 bmd/bmd? Storage mode (trace b) function this command selects trace b storage mode. Command bmd mode query bmd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear average details this command is not available during t...

  • Page 1115

    Chapter ４ native device message details 4-33 4 n ati ve d ev ice m es sa ge d et ail s bndc/bndc? Band select function this command selects frequency band. Note this command is provided for backward compatibility. Setting except auto is not available. Command bndc mode query bndc? Response mode para...

  • Page 1116

    Chapter ４ native device message details 4-34 bndsp/bndsp? Frequency band mode function this command sets the frequency band path. The frequency at which the path is switched to the preselector band or a path that does not pass through the preselector can be set with this function. Command bndsp mode...

  • Page 1117

    Chapter ４ native device message details 4-35 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the frequency to be switched to the preselector band to 6.0 ghz. Bndsp normal bndsp? > normal cal calibration function this command executes calibration. Command cal mode parameter mode calib...

  • Page 1118

    Chapter ４ native device message details 4-36 cal:rcl/cal:rcl? Adjust reference clock function this command sets the adjustment value for the internal reference signal oscillator (reference clock). Command cal:rcl integer query cal:rcl? Response integer parameter integer adjustment value range 0 to 1...

  • Page 1119

    Chapter ４ native device message details 4-37 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:aoff all marker off function this command sets all the markers to off. Command calc:mark:aoff details this command is not available in the following cases: • during the spectrum emission mask measurement...

  • Page 1120

    Chapter ４ native device message details 4-38 calc:mark:coup:zone/ calc:mark:coup:zone? Couple zone function this command sets the zone width shared setting to on/off. Command calc:mark:coup:zone switch_com query calc:mark:coup:zone? Response switch_res parameter switch_com zone width shared setting ...

  • Page 1121

    Chapter ４ native device message details 4-39 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:fco/calc:mark:fco? Frequency counter state function this command turns on/off the frequency counter. Command calc:mark:fco n,switch query calc:mark:fco? N parameter n marker number 1 specifies marker 1 2...

  • Page 1122

    Chapter ４ native device message details 4-40 example of use to set marker 1 as the active marker and switch on the frequency counter function. Calc:mark:fco 1,on calc:mark:fco? 1 > 1.

  • Page 1123

    Chapter ４ native device message details 4-41 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:fco:gat/calc:mark:fco:gat? Frequency counter gate time function this command sets the counter gate time for frequency counter. Command calc:mark:fco:gat n,time query calc:mark:fco:gat? N response time pa...

  • Page 1124

    Chapter ４ native device message details 4-42 calc:mark:fco:x? Frequency counter query function this command queries the measured value of the frequency counter. Query calc:mark:fco:x? N response freq parameter n marker number 1 specifies marker 1 2 specifies marker 2 3 specifies marker 3 4 specifies...

  • Page 1125

    Chapter ４ native device message details 4-43 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:max:pow power peak search function this command moves the active marker to the position where the peak power of the zone width of the active marker becomes maximum in the measurement band. Command calc:m...

  • Page 1126

    Chapter ４ native device message details 4-44 calc:mark:max:pow:next next power peak search function this command searches for the next largest peak power in the zone width compared to the total power of the zone width of the active marker in the measurement band and moves the active marker. Command ...

  • Page 1127

    Chapter ４ native device message details 4-45 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:peak:sort:coun/calc:mark:peak:sort:coun? Search peaks number function this command sets the search number when search peaks sort y/x is executed. Command calc:mark:peak:sort:coun integer query calc:mark:...

  • Page 1128

    Chapter ４ native device message details 4-46 calc:mark:peak:sort:x search peaks sort x function this command sorts as many markers as the number set in search peaks number by frequency (time) on the trace. Command calc:mark:peak:sort:x details this command is not available in the following cases: • ...

  • Page 1129

    Chapter ４ native device message details 4-47 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:read? Marker readout query function this command queries all marker values. Query calc:mark:read? Response freq_1,power_1,freq_2,power_2,..., freq_10,power_10 (in frequency domain) time_1,power_1,time_2,...

  • Page 1130

    Chapter ４ native device message details 4-48 time_n time of marker n no suffix code, in s units, resolution: 0.1 ns returns –999999999999 when no measurement is performed, an error occurs, or the marker is off. Details this command is not available during the spurious emission measurement and when d...

  • Page 1131

    Chapter ４ native device message details 4-49 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:ref/calc:mark:ref? Relative to function this command sets the reference marker when marker mode is set to delta. Command calc:mark:ref marker,integer query calc:mark:ref? Marker response integer paramete...

  • Page 1132

    Chapter ４ native device message details 4-50 details the selected marker cannot be set as the reference marker. This command is not available in the following cases: • during the spurious emission measurement. • during the spectrum emission mask measurement. • during the spurious emission measuremen...

  • Page 1133

    Chapter ４ native device message details 4-51 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:slin/calc:mark:slin? Spot line function this command displays/hides the marker line in the spot marker. Command calc:mark:slin switch_com query calc:mark:slin? Response switch_res parameter switch_com ma...

  • Page 1135

    Chapter ４ native device message details 4-53 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:trck/calc:mark:trck? Marker tracking function this command sets the marker tracking function to on/off. Command calc:mark:trck switch_com query calc:mark:trck? Response switch_res parameter switch_com ma...

  • Page 1136

    Chapter ４ native device message details 4-54 calc:mark:widt:type/calc:mark:widt:type? Zone width type function this command sets the zone width type of the marker. Command calc:mark:widt:type n,zone_type query calc:mark:widt:type? N parameter n marker number 1 marker 1 2 marker 2 3 marker 3 4 marker...

  • Page 1137

    Chapter ４ native device message details 4-55 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:x:delt/calc:mark:x:delt? Zone marker relative frequency (time) function this command moves the center of the zone marker to the frequency (time), specified by relative value. This queries the center freq...

  • Page 1138

    Chapter ４ native device message details 4-56 suffix code ns, us, ms, s s is used when the suffix code is omitted. Default 0 s details this command is not available during spurious emission measurement and when displayed segment mode is auto. Not available during spectrum emission mask measurement. N...

  • Page 1139

    Chapter ４ native device message details 4-57 4 n ati ve d ev ice m es sa ge d et ail s calc:mark:y:delt? Marker relative level query function this command queries the marker level in relative value. Query calc:mark:y:delt? Marker response level parameter marker marker number 1 specifies marker 1 2 s...

  • Page 1140

    Chapter ４ native device message details 4-58 calc:spur:corr:comm use common correction table function this command uses the common correction data set in cal as correction data. Command calc:spur:corr:comm integer parameter integer segment number range 1 to 20 resolution 1 example of use to use the ...

  • Page 1141

    Chapter ４ native device message details 4-59 4 n ati ve d ev ice m es sa ge d et ail s calc:spur:corr:rec recall correction table function this command selects the correction table to use in segment. Command calc:spur:corr:rec integer,filename,device parameter integer segment number range 1 to 20 re...

  • Page 1142

    Chapter ４ native device message details 4-60 calc:spur:lim:abs:data/calc:spur:lim:abs:data? Spurious emission limit start level function this command sets the absolute level limit of the start frequency in each segment for the spurious emission measurement. Command calc:spur:lim:abs:data ampl_1,ampl...

  • Page 1143

    Chapter ４ native device message details 4-61 4 n ati ve d ev ice m es sa ge d et ail s calc:spur:lim:abs:data:stop/calc:spur:lim:abs:data:stop? Spurious emission limit stop level function this command sets the absolute level limit of the stop frequency of each segment for the spurious emission measu...

  • Page 1144

    Chapter ４ native device message details 4-62 calc:spur:lim:abs:data:stop:auto/calc:spur:lim:abs:data:sto p:auto? Spurious emission limit stop level auto/manual function this command sets the absolute level limit of the stop frequency in each segment for the spurious emission measurement to auto/manu...

  • Page 1145

    Chapter ４ native device message details 4-63 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the absolute level limit of the stop frequency in each segment to auto/manual. Calc:spur:lim:abs:data:stop:auto on,on,on,on,off,off,off,on,on,on,on,on,on,on,on,on,on,on ,on,on calc:spur:lim:a...

  • Page 1146

    Chapter ４ native device message details 4-64 chpwrfltrtyp/chpwrfltrtyp? Channel power filter type function this command sets filter type for channel power measurement. Command chpwrfltrtyp filter query chpwrfltrtyp? Response filter parameter filter filter type rect rect. Filter nyquist nyquist filte...

  • Page 1147

    Chapter ４ native device message details 4-65 4 n ati ve d ev ice m es sa ge d et ail s chpwrrof/chpwrrof? Channel power rolloff factor function this command sets filter rolloff ratio for channel power measurement. Command chpwrrof factor query chpwrrof? Response factor parameter factor rolloff ratio...

  • Page 1148

    Chapter ４ native device message details 4-66 chpwrwidth/chpwrwidth? Channel power channel bandwidth function this command sets the channel bandwidth for channel power measurement. Command chpwrwidth freq query chpwrwidth? Response freq returns a value in hz units, without a suffix code. Parameter fr...

  • Page 1149

    Chapter ４ native device message details 4-67 4 n ati ve d ev ice m es sa ge d et ail s cmd/cmd? Storage mode (trace c) function this command selects the storage mode of trace c. Command cmd mode query cmd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear avera...

  • Page 1150

    Chapter ４ native device message details 4-68 cmk? Marker position query function this command queries the marker position using the displayed point from the screen left edge. Query cmk? Marker response point parameter point marker position (number of displayed points from the screen left edge) range...

  • Page 1151

    Chapter ４ native device message details 4-69 4 n ati ve d ev ice m es sa ge d et ail s cnf/cnf? Center frequency function this command sets the center frequency. Command cnf freq query cnf? Response freq no suffix code. Value is returned in hz units. Parameter freq center frequency range [ms269xa] –...

  • Page 1152

    Chapter ４ native device message details 4-70 cnvloss/cnvloss? External mixer conversion loss function this command sets the external mixer's conversion loss. Command cnvloss power query cnvloss? Response power parameter power external mixer's conversion loss range 0.00 to 99.99 db resolution 0.01 db...

  • Page 1153

    Chapter ４ native device message details 4-71 4 n ati ve d ev ice m es sa ge d et ail s conf:san measurement off function this command disables currently running measurement function. No operation is made if no measurement function is running. Command conf:san example of use to disable the currently ...

  • Page 1154

    Chapter ４ native device message details 4-72 conf:spur spurious emission configure function this command sets the spurious emission measurement to on. Command conf:spur details no measurement is performed. When spurious emission measurement is set to on, the active trace is set to a. Example of use ...

  • Page 1155

    Chapter ４ native device message details 4-73 4 n ati ve d ev ice m es sa ge d et ail s det/det? Detection mode function this command selects the waveform pattern detection mode. When couple time/frequency domain is set to off, each parameter is specified in accordance with the already-specified freq...

  • Page 1156

    Chapter ４ native device message details 4-74 example of use to set the detection mode to positive peak. Det pos det? > pos disp:sem:res:type/disp:sem:res:type? Spectrum emission mask result type function this command switches the type of the result display for spectrum emission mask measurement. Com...

  • Page 1157

    Chapter ４ native device message details 4-75 4 n ati ve d ev ice m es sa ge d et ail s disp:spur:segm/disp:spur:segm? Displayed segment function this command specifies the segment to display the trace data in. Command disp:spur:segm integer query disp:spur:segm? Response integer parameter integer se...

  • Page 1158

    Chapter ４ native device message details 4-76 disp:spur:segm:auto/disp:spur:segm:auto? Page of summary auto/manual function this command turns on the summary page auto numbering. Command disp:spur:segm:auto switch_com query disp:spur:segm:auto? Response switch_res parameter switch_com auto mode on/of...

  • Page 1159

    Chapter ４ native device message details 4-77 4 n ati ve d ev ice m es sa ge d et ail s disp:spur:segm:mode/disp:spur:segm:mode? Displayed segment mode function this command switches the display mode of a segment. Command disp:spur:segm:mode switch_com query disp:spur:segm:mode? Response switch_res p...

  • Page 1160

    Chapter ４ native device message details 4-78 disp:spur:segm:next next page function this command displays the summary on the next page. Command disp:spur:segm:next details the summary set in result type is displayed. Example of use to display the summary on the next page. Disp:spur:seg:next disp:spu...

  • Page 1161

    Chapter ４ native device message details 4-79 4 n ati ve d ev ice m es sa ge d et ail s disp:spur:segm:rest? Displayed restart query function this command queries whether the remeasurement message is displayed on the trace. Query disp:spur:segm:rest? Response switch parameter switch message displayed...

  • Page 1162

    Chapter ４ native device message details 4-80 displ:spur:stab/disp:spur:stab? Displayed summary table function this command sets the content to be displayed in the summary table. Command disp:spur:stab mode_com query disp:spur:stab? Response mode_res parameter mode_com the contents displayed for summ...

  • Page 1163

    Chapter ４ native device message details 4-81 4 n ati ve d ev ice m es sa ge d et ail s disp:spur:view:wind:trac:y:rlev/disp:spur:view:wind:trac:y:r lev? Spurious emission reference level function this command sets the reference level of each segment. Command disp:spur:view:wind:trac:y:rlev real_1,re...

  • Page 1164

    Chapter ４ native device message details 4-82 dmd/dmd? Storage mode (trace d) function this command sets the storage mode of trace d. Command dmd mode query dmd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear average details this command is not available in t...

  • Page 1165

    Chapter ４ native device message details 4-83 4 n ati ve d ev ice m es sa ge d et ail s dpoint/dpoint? Trace point function this command sets the number of trace display points. When couple time/frequency domain is set to off, each parameter is specified in accordance with the already-specified frequ...

  • Page 1166

    Chapter ４ native device message details 4-84 emd/emd? Storage mode (trace e) function this command sets the storage mode of trace e. Command emd mode query emd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear average details this command is not available in t...

  • Page 1167

    Chapter ４ native device message details 4-85 4 n ati ve d ev ice m es sa ge d et ail s erasewup erase warm up message function this command erases the warm up message displayed after startup. Command erasewup example of use to erase the warm up message. Erasewup ese2/ese2? End event status enable co...

  • Page 1168

    Chapter ４ native device message details 4-86 range 0 to 255 example of use to enable the measurement end (end of measure) status. Ese2 32 ese2? > 1 esr2? End event status register query function this command queries the end event status register value. Clears the end event status register after read...

  • Page 1169

    Chapter ４ native device message details 4-87 4 n ati ve d ev ice m es sa ge d et ail s fetc:sem? Spectrum emission mask fetch function this command outputs the result of spectrum emission mask measurement. Query fetc:sem? N response when the result mode is “a”. Total_judge,ref_power,abs_lower_offset...

  • Page 1170

    Chapter ４ native device message details 4-88 freq_lower_offset_1 -999.0,-999.0, rel_upper_offset_1,abs_upper_offset_1, freq_upper_offset_1 -999.0,-999.0, rel_lower_offset_2,abs_lower_offset_2, freq_lower_offset_2 -999.0,-999.0, rel_upper_offset_2,abs_upper_offset_2, freq_upper_offset_2 -999.0,-999.0...

  • Page 1171

    Chapter ４ native device message details 4-89 4 n ati ve d ev ice m es sa ge d et ail s lower_offset_3,upper_offset_3, lower_offset_4,upper_offset_4, lower_offset_5,upper_offset_5, lower_offset_6,upper_offset_6 (n=7 or 8) -999.0,-999.0, abs_lower_offset_1,abs_upper_offset_1, abs_lower_offset_2,abs_up...

  • Page 1172

    Chapter ４ native device message details 4-90 rel_upper_offset_n peak value of relative power of upper offset-n margin_lower_offset_n minimum value of margin of lower offset-n margin_upper_offset_n minimum value of margin of upper offset-n no suffix code, db unit, 0.001 db resolution returns –999.0 w...

  • Page 1173

    Chapter ４ native device message details 4-91 4 n ati ve d ev ice m es sa ge d et ail s fetc:spur? Spurious emission fetch function this command outputs the result of the spurious emission measurement. Query fetc:spur? N response when result mode is a: (when spurious emission result type is worst) ju...

  • Page 1174

    Chapter ４ native device message details 4-92 tracedata_1,tracedata_2•••••tracedata_m (n=23 to 42) parameter range_n segment number of the detected spurious spur_n spurious number number number of the detected spurious –999.0 is returned when an error occurs/no measurement is performed. Freq_n freque...

  • Page 1175

    Chapter ４ native device message details 4-93 4 n ati ve d ev ice m es sa ge d et ail s tracedata_m n=2 to 21 returns a comma separated list of the trace data for the selected segment (where segment number = n-1). N=23 to 42 returns a comma separated list of the trace data for the selected segment (w...

  • Page 1176

    Chapter ４ native device message details 4-94 fmd/fmd? Storage mode (trace f) function this command sets the storage mode of trace f. Command fmd mode query fmd? Response mode parameter mode storage mode 0 off 1 max hold 2 average 3 min hold 6 linear average details this command is not available in t...

  • Page 1177

    Chapter ４ native device message details 4-95 4 n ati ve d ev ice m es sa ge d et ail s foffset/foffset? Frequency offset function this command sets the offset value of the frequency display. Command foffset freq query foffset? Response freq no suffix code. Value is returned in hz units. Parameter fr...

  • Page 1178

    Chapter ４ native device message details 4-96 fofmd/fofmd? Frequency offset mode function this command sets the frequency display offset on/off. Command fofmd on_off query fofmd? Response on_off parameter on_off frequency display offset on/off on uses frequency display offset. Off does not use freque...

  • Page 1179

    Chapter ４ native device message details 4-97 4 n ati ve d ev ice m es sa ge d et ail s form/form? Numeric data format function this command sets the format of the data that is read out with [:sense]:data?. Command form format query form? Response format length parameter format data format asc ascii ...

  • Page 1180

    Chapter ４ native device message details 4-98 form:bord/form:bord? Binary data byte order function this command sets the byte order of the data that is read out, when real,32 or integer,32 has been set for form. Command form:bord border query form:bord? Parameter border byte order norm sets the byte ...

  • Page 1181

    Chapter ４ native device message details 4-99 4 n ati ve d ev ice m es sa ge d et ail s freq:cent:step/freq:cent:step? Frequency step size function this command sets the step size of the center, start and stop frequency. Command freq:cent:step freq query freq:cent:step? Parameter freq step size range...

  • Page 1182

    Chapter ４ native device message details 4-100 freq:dom:coup/freq:dom:coup? Couple time/frequency domain function sets whether to couple the time domain parameters and frequency domain parameters. Command freq:dom:coup switch_com query freq:dom:coup? Response switch_res parameter switch_com enables/d...

  • Page 1183

    Chapter ４ native device message details 4-101 4 n ati ve d ev ice m es sa ge d et ail s freq:synt/freq:synt? Switching speed function this command selects the switching speed of frequency. Command freq:synt mode query freq:synt? Response mode frequency switching mode parameter mode frequency switchi...

  • Page 1184

    Chapter ４ native device message details 4-102 freq:synt:lph:stat? Low phase noise status query function this command queries the state of low phase noise function with the current measurement conditions. Query freq:synt:lph:stat? Response status parameter status low phase noise function on/off statu...

  • Page 1185

    Chapter ４ native device message details 4-103 4 n ati ve d ev ice m es sa ge d et ail s fs full span function this command sets the frequency span to the maximum. Command fs details this command is not available during the spectrum emission mask measurement or the spurious emission measurement. Exam...

  • Page 1186

    Chapter ４ native device message details 4-104 g band g (140.0 to 220.0 ghz, 22+) y band y (170.0 to 260.0 ghz, 26+) j band j (220.0 to 325.0 ghz, 33+) details this function is available when option 044/045 is installed for ms2830a. This function is available when option 044/046 is installed for ms28...

  • Page 1187

    Chapter ４ native device message details 4-105 4 n ati ve d ev ice m es sa ge d et ail s gate/gate? Gate sweep function this command sets the gate sweep on/off. Command gate on_off query gate? Response on_off parameter on_off gate sweep on/off on uses gate sweep. Off does not use gate sweep. Details ...

  • Page 1188

    Chapter ４ native device message details 4-106 gatelvl/gatelvl? Gate level function this command sets the threshold value of the level where gate sweep is started. Command gatelvl level query gatelvl? Response level returns a value in dbm units, without a suffix code. Parameter level threshold value ...

  • Page 1189

    Chapter ４ native device message details 4-107 4 n ati ve d ev ice m es sa ge d et ail s gateslp/gateslp? Gate slope function this command sets the gate signal detection mode. Command gateslp edge query gateslp? Response edge parameter edge gate signal detection mode rise detects using the rising edg...

  • Page 1190

    Chapter ４ native device message details 4-108 gatesource/gatesource? Gate source function this command sets the gate signal source. Command gatesource source query gatesource? Response source parameter source gate signal source [ms269xa] widevid wideband if detection (wide if video) ext external inp...

  • Page 1191

    Chapter ４ native device message details 4-109 4 n ati ve d ev ice m es sa ge d et ail s gdl/gdl? Gate delay function this command sets the delay time until starting gate sweep. Command gdl time query gdl? Response time returns a value in µs units, without a suffix code. Parameter time delay time to ...

  • Page 1192

    Chapter ４ native device message details 4-110 gln/gln? Gate length function this command sets the gate time length. Command gln time query gln? Response time no suffix code. Value is returned in µs units. Parameter time delay time until starting gate range 50 µs to 1 s resolution 20 ns suffix code n...

  • Page 1193

    Chapter ４ native device message details 4-111 4 n ati ve d ev ice m es sa ge d et ail s holdpause/holdpause? Storage count function this command sets the storage mode count. Command holdpause count query holdpause? Response count parameter count storage mode count range 2 to 9999 details this comman...

  • Page 1194

    Chapter ４ native device message details 4-112 init:sem spectrum emission mask initiate function this command performs single spectrum emission mask measurement. Command init:sem details when this function is executed, spectrum emission mask measurement is set to on and the measurement is performed o...

  • Page 1195

    Chapter ４ native device message details 4-113 4 n ati ve d ev ice m es sa ge d et ail s init:spur:paus:cont spurious emission continue function pause is cancelled and measurement will continue when this command is sent while it is in remote control state and paused. Command init:spur:paus:cont detai...

  • Page 1196

    Chapter ４ native device message details 4-114 init:spur:paus:stat? Spurious emission pause status query function this command queries whether the spurious emission measurement is in remote control state and is being paused. Query init:spur:paus:stat? Response switch parameter switch status of the sp...

  • Page 1197

    Chapter ４ native device message details 4-115 4 n ati ve d ev ice m es sa ge d et ail s linscalediv/linscalediv? Linear scale range function this command sets the y-axis scale magnification for the linear scale display. Command linscalediv scale query linscalediv? Response scale no suffix code. Valu...

  • Page 1198

    Chapter ４ native device message details 4-116 loadstd/loadstd? Load standard parameter function this command selects measure function parameter. Selectable parameters vary depending on the setting for standard. Command loadstd function,pattern query loadstd? Function parameter function measure funct...

  • Page 1199

    Chapter ４ native device message details 4-117 4 n ati ve d ev ice m es sa ge d et ail s mean 3gpp w-cdma uplink, mean power measurement rrcfilter 3gpp w-cdma uplink, rrc filtered power measurement when omitted 3gpp w-cdma uplink, mean power measurement when standard is set to w-cdma uplink (spectrum...

  • Page 1200

    Chapter ４ native device message details 4-118 when standard is set to w-cdma downlink (channel power measurement) pattern parameter to be set downlink 3gpp w-cdma downlink, mean power measurement mean 3gpp w-cdma downlink, mean power measurement rrcfilter 3gpp w-cdma downlink, rrc filtered power mea...

  • Page 1201

    Chapter ４ native device message details 4-119 4 n ati ve d ev ice m es sa ge d et ail s when standard is set to mobile wimax (burst average power measurement) pattern parameter to be set 5ms_frame 5 ms frame (power measurement of 1 frame) when omitted 5 ms frame when standard is set to lte uplink/do...

  • Page 1202

    Chapter ４ native device message details 4-120 20mbw_eutra20mhz 20 mhz bw (e-utra 20 mhz) when omitted 5 mhz bw (e-utra 5 mhz) when standard set to lte tdd uplink (acp measurement) pattern parameter to set 1m4bw_utra1m6hz 1.4 mhz bw (utra 1.6 mhz) 1m4bw_eutra1m4hz 1.4 mhz bw (e-utra 1.4 mhz) 3mbw_utr...

  • Page 1203

    Chapter ４ native device message details 4-121 4 n ati ve d ev ice m es sa ge d et ail s filtered_20mbw filtered power 20 mhz bw when omitted: mean power 5 mhz bw when standard set to lte uplink/downlink, lte tdd uplink/downlink (burst average power measurement) pattern parameter to set mean_1m4bw me...

  • Page 1204

    Chapter ４ native device message details 4-122 note: class 5, 6, 8, 12, 13, 14, 17 >1ghz: bandclass when frequency larger than 1 ghz. 1, 2, 3, 4, 7, 9, 10, 11 when standard is set to lte uplink (spectrum emission mask measurement) pattern parameter to set g_1_4m general 1.4 mhz g_3m general 3 mhz g_5...

  • Page 1205

    Chapter ４ native device message details 4-123 4 n ati ve d ev ice m es sa ge d et ail s when standard is set to lte tdd uplink (spectrum emission mask measurement) pattern parameter to be set g_1_4m general 1.4 mhz g_3m general 3 mhz g_5m general 5 mhz g_10m general 10 mhz g_15m general 15 mhz g_20m...

  • Page 1206

    Chapter ４ native device message details 4-124 when standard is set to td-scdma (acp measurement) pattern parameter to be set tdd128m1c single carrier tdd128m2c 2 carriers tdd128m3c 3 carriers tdd128m4c 4 carriers tdd128m5c 5 carriers tdd128m6c 6 carriers when omitted single carrier when standard is ...

  • Page 1207

    Chapter ４ native device message details 4-125 4 n ati ve d ev ice m es sa ge d et ail s when standard is set to xg-phs (obw measurement) pattern parameter to be set 10mbw 10 mhz bw 20mbw 20 mhz bw when omitted 10 mhz bw when standard is set to xg-phs (chp measurement) pattern parameter to be set mea...

  • Page 1208

    Chapter ４ native device message details 4-126 when standard set to ev-do forward link (acp, burst average, channel power, obw measurement) pattern parameter to set evdofwd ev-do forward link when omitted ev-do forward link when standard set to ev-do forward link (spectrum emission mask measurement) ...

  • Page 1209

    Chapter ４ native device message details 4-127 4 n ati ve d ev ice m es sa ge d et ail s when standard is set to isdb-t sb (spectrum emission mask measurement) pattern parameter to set 3m9bw 3.9 mhz bw when omitted 3.9 mhz bw when standard is set to isdb-t (channel power measurement) pattern paramete...

  • Page 1210

    Chapter ４ native device message details 4-128 t401_ofdm telec t-401 2.4 ghz enhanced low power data communication system, orthogonal frequency division multiplexing system t403_20mbw telec t-403 5 ghz low power data communication system 20 mhz system t403_40mbw telec t-403 5 ghz low power data commu...

  • Page 1211

    Chapter ４ native device message details 4-129 4 n ati ve d ev ice m es sa ge d et ail s w11ac160mhz ieee802.11ac 160 mhz etsi_ofdm_5mhz en 301 893 4.5.2 transmitter unwanted emissions within the 5 ghz rlan bands 5 mhz etsi_ofdm_10mhz en 301 893 4.5.2 transmitter unwanted emissions within the 5 ghz r...

  • Page 1212

    Chapter ４ native device message details 4-130 5180 to 5240 mhz upper sideband, obw more than 18 mhz, less than 19 mhz t403_18_19mhz_5260_5320mhz_lower telec t-403 5 ghz low power data communication system 5260 to 5320 mhz lower sideband, obw more than 18 mhz, less than 19 mhz t403_18_19mhz_5260_5320...

  • Page 1213

    Chapter ４ native device message details 4-131 4 n ati ve d ev ice m es sa ge d et ail s t403_5250mhz_lower telec t-403 5 ghz low power data communication system 5250 mhz lower sideband t403_5250mhz_upper telec t-403 5 ghz low power data communication system 5250 mhz lower sideband t403_5210mhz_80-80...

  • Page 1214

    Chapter ４ native device message details 4-132 t401 telec t-401 2.4 ghz enhanced low power data communication system t402 telec t-402 2.4 ghz low power data communication system t403_18mhz_5_2ghz telec t-403 5 ghz low power data communication system 5.2 ghz obw less than 18 mhz t403_18mhz_5_3ghz tele...

  • Page 1215

    Chapter ４ native device message details 4-133 4 n ati ve d ev ice m es sa ge d et ail s t403_38_78mhz_5_3ghz telec t-403 5 ghz low power data communication system 5.3 ghz obw more than 38 mhz, less than 78 mhz t403_38_78mhz_5_6ghz telec t-403 5 ghz low power data communication system 5.6 ghz obw mor...

  • Page 1216

    Chapter ４ native device message details 4-134 t405_20mhz_4_9ghz_dcck telec t-405 5 ghz wireless access system 20 mhz system direct sequence spread spectrum system 4,900 mhz to 5,000 mhz t405_20mhz_5_0ghz_ofdm telec t-405 5 ghz wireless access system 20 mhz system orthogonal frequency division multip...

  • Page 1217

    Chapter ４ native device message details 4-135 4 n ati ve d ev ice m es sa ge d et ail s gfsk_920m_200k gfsk 920mhz 200ksps (arib std-t108) gfsk_50k_g gfsk 50ksps (ieee802.15.4g_d7) gfsk_100k_g gfsk 100ksps (ieee802.15.4g_d7) gfsk_200k_g gfsk 200ksps (ieee802.15.4g_d7) when omitted bpsk 950mhz (arib ...

  • Page 1218

    Chapter ４ native device message details 4-136 frequency band:above30ghz 7m5b3-17g cs:7mhz class:5b frequency band:3g-17ghz 7m5b17-30g cs:7mhz class:5b frequency band:17g-30ghz 7m5babv30g cs:7mhz class:5b frequency band:above30ghz 14m2 cs:14mhz class:2 14m4l3-17g cs:14mhz class:4l frequency band:3g-1...

  • Page 1219

    Chapter ４ native device message details 4-137 4 n ati ve d ev ice m es sa ge d et ail s frequency band:above30ghz 56m4l3-17g cs:56mhz class:4l frequency band:3g-17ghz 56m4l17-30g cs:56mhz class:4l frequency band:17g-30ghz 56m4labv30g cs:56mhz class:4l frequency band:above30ghz 56m5a6a3-17g cs:56mhz ...

  • Page 1220

    Chapter ４ native device message details 4-138 logscalediv/logscalediv? Log scale range function this command sets the y-axis scale magnification for the log scale display. Command logscalediv scale query logscalediv? Response scale no suffix code. Value is returned in db units. Parameter scale y-axi...

  • Page 1221

    Chapter ４ native device message details 4-139 4 n ati ve d ev ice m es sa ge d et ail s madjmod/madjmod? Acp reference function this command sets the reference of the relative level display for acp measurement command madjmod method madjmod num query madjmod? Response method num parameter method ref...

  • Page 1222

    Chapter ４ native device message details 4-140 mbias/mbias? External mixer bias function this command sets the external mixer's bias current. Command mbias bias query mbias? Response bias parameter bias external mixer's bias current range 0.0 to 20.0 ma resolution 0.1 ma suffix code none, value is re...

  • Page 1223

    Chapter ４ native device message details 4-141 4 n ati ve d ev ice m es sa ge d et ail s meas/meas? Measure function function this command selects and executes the measurement item and method for measure function. Command meas func,method meas func,num meas off query meas? Response func parameter fun...

  • Page 1224

    Chapter ４ native device message details 4-142 num carrier number used for acp measurement range 1 to carrier number (cf. Adjcarriernum) resolution 1 suffix code none details when measuring as the sem function (func), this becomes the overlap command. When querying the measurement result after execut...

  • Page 1225

    Chapter ４ native device message details 4-143 4 n ati ve d ev ice m es sa ge d et ail s meas:batc:acp? Adjacent channel power batch measure function this command executes acp measurement and outputs the result after the parameters described in the specified parameter list file have been set. Query m...

  • Page 1226

    Chapter ４ native device message details 4-144 example of use to option the results of acp measurement performed using the parameter list file myparam.Xml. Meas:batc:acp? 1,"myparam.Xml" > 0.0,-72.130,0.0,-72.130,-1.270,-73.400,-0.570,-72.700,-0 .780,-72.910,-1.030,-73.160,-999.0,-999.0,-999.0,-999.0...

  • Page 1227

    Chapter ４ native device message details 4-145 4 n ati ve d ev ice m es sa ge d et ail s parameter filename parameter list file specify with any character string enclosed by double quotes (" ") or single quotes (' ') spa_freq center frequency of the spectrum analyzer function. Range –100 mhz to 6.05 ...

  • Page 1228

    Chapter ４ native device message details 4-146 details this command executes transmit intermodulation measurement and outputs the result based on the specified parameter list file. Place parameter list files in a folder on the specified drive. :\anritsu corporation\signal analyzer\user data\batch if ...

  • Page 1229

    Chapter ４ native device message details 4-147 4 n ati ve d ev ice m es sa ge d et ail s meas:batc:obw? Occupied bandwidth batch measure function this command executes obw measurement and outputs the measurement result after the parameters described in the specified parameter list file have been set....

  • Page 1230

    Chapter ４ native device message details 4-148 example of use to acquire the measurement result of obw measurement using the myparam.Xls parameter list file (a mode, n = 1). Read:batc:obw? 1,"myparam.Xml" > 30000,1000000000,900050000,1000050000 format of parameter list file refer to :measure:batch:ob...

  • Page 1231

    Chapter ４ native device message details 4-149 4 n ati ve d ev ice m es sa ge d et ail s meas:batc:sem? Spectrum emission mask batch measure function this command executes spectrum emission mask measurement and outputs the measurement result after the parameters described in the specified parameter l...

  • Page 1232

    Chapter ４ native device message details 4-150 example of use to acquire the peak value of absolute power of sem measurement using the myparam.Xls parameter list file (n = 10). Meas:batc:sem? 10,"myparam.Xml" > 999.0,-999.0,-100.000,-100.000,-60.000,-60.000,45.000,-4 5.000,-30.000,-30.000,-10.000,-10...

  • Page 1233

    Chapter ４ native device message details 4-151 4 n ati ve d ev ice m es sa ge d et ail s meas:batc:spur? Spurious emission batch measure function this command executes spurious emission measurement and outputs the measurement result after the parameters described in the specified parameter list file ...

  • Page 1234

    Chapter ４ native device message details 4-152 example of use to acquire the measurement result of spurious emission measurement (when result mode = a, spurious emission result type = worst) fetc:spur? 1,"myparam.Xml" > 0,1,1,135618.00,-64.25,51.25,-13.00,0,2,2,155970.00,-63. 91,50.91,-13.00,0•••• fo...

  • Page 1235

    Chapter ４ native device message details 4-153 4 n ati ve d ev ice m es sa ge d et ail s meas:pow? Measure power adjust function this command executes power adjustment and reads the result. Power adjustment combines the sg option and power measurement functions to set the output level of the dut, suc...

  • Page 1236

    Chapter ４ native device message details 4-154 is not exceeded. Range [ms269xa] –140 to –5 dbm [ms2830a], [ms2840a] –40.00 to +20.00 dbm (>25 mhz) –40.00 to +2.00 dbm (≤25 mhz) –136.00 to +15.00 dbm (>25 mhz) (option 022/122) –136.00 to –3.00 dbm (≤25 mhz) (option 022/122) resolution 0.01 dbm sg_max_...

  • Page 1237

    Chapter ４ native device message details 4-155 4 n ati ve d ev ice m es sa ge d et ail s [ms2840a] 250 khz to 3.6 ghz (option 020/122) 250 khz to 6 ghz (option 041, and 021/121) resolution 1 hz suffix code hz, khz, kz, mhz, mz, ghz, gz hz is used when omitted. Maximum, minimum, and default cannot be ...

  • Page 1238

    Chapter ４ native device message details 4-156 sg_output output level of sg output of this equipment no suffix code, dbm (unit), 0.01 db (resolution) –999.0 is returned if there is no measurement. Count_res power adjustment execution count time power adjustment time 1 ms (resolution) no suffix code, ...

  • Page 1239

    Chapter ４ native device message details 4-157 4 n ati ve d ev ice m es sa ge d et ail s * offset :reference level offset value however, it is rounded to 60 db when attenuator > 60 and to 0 dbm when attenuator number, it is rounded up to the nearest even number (example: 35 db →36 db). After executin...

  • Page 1240

    Chapter ４ native device message details 4-158 meas:sem? Spectrum emission mask measure function this command performs the measurement for spectrum emission mask measurement and outputs the measurement result. It works in the same way as the three commands are transmitted in the following order: conf...

  • Page 1241

    Chapter ４ native device message details 4-159 4 n ati ve d ev ice m es sa ge d et ail s mkact/mkact? Active marker function this command sets the active marker. Command mkact marker query mkact? Response marker parameter marker active marker mkr1 marker 1 mkr2 marker 2 mkr3 marker 3 mkr4 marker 4 mk...

  • Page 1242

    Chapter ４ native device message details 4-160 mkcf marker to center frequency function this command sets the marker frequency to the center frequency. Command mkcf details this command is not available in the following cases: • when the marker mode is set to off. • during the spurious emission measu...

  • Page 1243

    Chapter ４ native device message details 4-161 4 n ati ve d ev ice m es sa ge d et ail s mkf? Marker frequency (time) query function this command queries the frequency or time at the marker point level. Regarding the delta marker, queries the frequency gap or time gap between the delta marker and the...

  • Page 1244

    Chapter ４ native device message details 4-162 mkl? Marker level query function this command queries the marker point level. In case of delta marker, it queries the level ratio. Query mkl? Marker response level marker point level no suffix code, in db units, 0.001 db (when marker level display units ...

  • Page 1245

    Chapter ４ native device message details 4-163 4 n ati ve d ev ice m es sa ge d et ail s mkltype/mkltype? Marker result function this command sets the type of the marker value. Command mkltype type_com query mkltype? Response type_res parameter type_com type of marker value int integral power in the ...

  • Page 1246

    Chapter ４ native device message details 4-164 mkn/mkn? Zone marker frequency (time) function this command moves the center of the zone marker to the specified frequency (time). Command mkn freq,marker mkn time,marker query mkn? Marker response freq a value without a suffix code that has a resolution...

  • Page 1247

    Chapter ４ native device message details 4-165 4 n ati ve d ev ice m es sa ge d et ail s suffix code ns,us,ms,s ms is used when omitted. Marker marker types 1 marker 1 2 marker 2 3 marker 3 4 marker 4 5 marker 5 6 marker 6 7 marker 7 8 marker 8 9 marker 9 10 marker 10 when omitted active marker detai...

  • Page 1248

    Chapter ４ native device message details 4-166 mkpk peak search function this command searches for the peak point of the active trace and moves the marker point to it. Command mkpk mkpk move parameter move peak point type hi moves to the highest peak point. Nh moves to the peak point below the level ...

  • Page 1249

    Chapter ４ native device message details 4-167 4 n ati ve d ev ice m es sa ge d et ail s mkpx/mkpx? Peak search resolution function this command sets the resolution for detecting the peak point. Command mkpx level query mkpx? Response level no suffix code, in db units, 0.001 db parameter level peak p...

  • Page 1250

    Chapter ４ native device message details 4-168 mkr/mkr? Marker mode function this command sets the marker mode. Command mkr mode_com,marker query mkr? Marker response mode_res parameter mode_com marker mode 0 normal marker 1 delta marker 2 off 3 fixed on normal marker off no marker displayed marker m...

  • Page 1251

    Chapter ４ native device message details 4-169 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the active marker mode to delta. Mkr 1 mkr? > 1 mkrl marker to reference level function this command sets the marker level to the reference level. Command mkrl details this command is not av...

  • Page 1252

    Chapter ４ native device message details 4-170 mktrace/mktrace? Marker trace function this command selects the trace (active trace) to operate the marker. Command mktrace trace,marker query mktrace? Marker_query response trace parameter marker marker type mkr1 marker 1 mkr2 marker 2 mkr3 marker 3 mkr...

  • Page 1253

    Chapter ４ native device message details 4-171 4 n ati ve d ev ice m es sa ge d et ail s trace trace type tra trace a trb trace b trc trace c trd trace d tre trace e trf trace f details this command is not available during the spectrum emission mask measurement or the spurious emission measurement. E...

  • Page 1254

    Chapter ４ native device message details 4-172 mkw/mkw? Zone marker width function this command sets the zone marker width. Command mkw width,marker query mkw? Marker response width returns *** when the zone marker width is not within the parameter range. Parameter width zone marker width 0 0.5 div 1...

  • Page 1255

    Chapter ４ native device message details 4-173 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the zone marker width to spot. Mkw 1 mkw? > 1 mkz/mkz? Zone marker position function this command moves the zone marker center to the specified position. Command mkz point,marker query mkz? ...

  • Page 1256

    Chapter ４ native device message details 4-174 details this command is not available in the following cases: • during the spurious emission measurement and when displayed segment mode is set to auto. • during the spectrum emission mask measurement. Example of use to move the zone marker center to 500...

  • Page 1257

    Chapter ４ native device message details 4-175 4 n ati ve d ev ice m es sa ge d et ail s –100 mhz to 13.6 ghz (option 043) –100 mhz to 26.6 ghz (option 044) –100 mhz to 43.1 ghz (option 045) [ms2840a] –100 mhz to 3.7 ghz (option 040) –100 mhz to 6.1 ghz (option 041) –100 mhz to 26.6 ghz (option 044) ...

  • Page 1258

    Chapter ４ native device message details 4-176 mmem:load:spur:tabl recall spurious emission parameter function this command queries the saved parameter for the spurious emission measurement. Command mmem:load:spur:tabl integer parameter integer register to read parameter range 1 to 8 example of use t...

  • Page 1259

    Chapter ４ native device message details 4-177 4 n ati ve d ev ice m es sa ge d et ail s mmem:rel:batc reloading parameter list files function this command applies the changes made to the parameter list files of the specified drive. Command mmem:rel:batc device parameter device drive name a,b,d,e,f,....

  • Page 1260

    Chapter ４ native device message details 4-178 mmem:stor:spur:tabl save spurious emission parameter function this command saves a parameter for the spurious emission measurement. Command mmem:stor:spur:tabl integer parameter integer register range 1 to 8 example of use to save a parameter in register...

  • Page 1261

    Chapter ４ native device message details 4-179 4 n ati ve d ev ice m es sa ge d et ail s mstat? Measurement status query function this command queries the measurement status. Query mstat? Response state measurement status 0 normal end 2 level over 9 not measured example of use to query the measuremen...

  • Page 1262

    Chapter ４ native device message details 4-180 mxrmode/mxrmode? Mixer mode function this command switches between internal and external mixer. Command mxrmode mode query mxrmode? Response mode parameter mode mixer mode ext selects external mixer int selects internal mixer details this function is ava...

  • Page 1263

    Chapter ４ native device message details 4-181 4 n ati ve d ev ice m es sa ge d et ail s mzw/mzw? Zone marker width (specified by point) function this command sets the zone marker width using the displayed points. Command mzw point,marker query mzw? Marker response point parameter point zone marker w...

  • Page 1264

    Chapter ４ native device message details 4-182 mzwf/mzwf? Zone marker width (by frequency) function this command sets the zone marker width using frequency. Command mzwf freq,marker query mzwf? Marker response freq returns a value in hz units, without a suffix code. Parameter freq zone marker frequen...

  • Page 1265

    Chapter ４ native device message details 4-183 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the zone marker width to 1 mhz. Mzwf 1mhz mzwf? > 1000000.00 noisecancel/noisecancel? Noise cancel function this command sets whether to enable the noise canceling function. Command noisecan...

  • Page 1266

    Chapter ４ native device message details 4-184 obwn/obwn? Obw n% ratio function this command sets the occupied frequency bandwidth (n% method) condition. Command obwn ratio query obwn? Response ratio no suffix code. Value is returned in % units. Parameter ratio n% range 0.01 to 99.99% resolution 0.01...

  • Page 1267

    Chapter ４ native device message details 4-185 4 n ati ve d ev ice m es sa ge d et ail s obwxdb/obwxdb? Obw x db value function this command sets the occupied frequency bandwidth (x db) condition. Command obwxdb level query obwxdb? Response level no suffix code. Value is returned in db units. Paramet...

  • Page 1268

    Chapter ４ native device message details 4-186 powermarker/powermarker? Power marker function this command changes the display mode of the marker value. Command powermarker on_off_com query powermarker? Response on_off_res parameter on_off_com marker result on integration off peak on_off_res marker r...

  • Page 1269

    Chapter ４ native device message details 4-187 4 n ati ve d ev ice m es sa ge d et ail s pow:mw:pres/pow:mw:pres? Micro wave preselector bypass function this command sets the micro wave preselector bypass. Command pow:mw:pres switch query pow:mw:pres? Response status parameter switch microwave presel...

  • Page 1270

    Chapter ４ native device message details 4-188 preamp/preamp? Pre amp function this command sets pre amp on/off. Command preamp on_off query preamp? Response on_off parameter on_off pre amp on/off on on off off details [ms269xa] this command is turned off and thus invalid when option 008/108 6 ghz pr...

  • Page 1271

    Chapter ４ native device message details 4-189 4 n ati ve d ev ice m es sa ge d et ail s presel/presel? Pre-selector tune function this command sets the pre-selector peaking bias value. Command presel action presel bias query presel? Response bias parameter action action auto sets peaking bias value ...

  • Page 1272

    Chapter ４ native device message details 4-190 [common] the frequency to be switched to the preselector band can be set by using frequency band mode. Automatic setting of the peaking bias value cannot be used during spurious measurement and when displayed segment mode is auto. Example of use to set t...

  • Page 1273

    Chapter ４ native device message details 4-191 4 n ati ve d ev ice m es sa ge d et ail s rb/rb? Resolution bandwidth function this command sets the resolution bandwidth (rbw). When couple time/frequency domain is set to off, each parameter is specified in accordance with the already-specified frequen...

  • Page 1274

    Chapter ４ native device message details 4-192 hz is used when omitted. Auto sets the resolution bandwidth automatically, according to the frequency span settings. Details in ms269xa, ms2830a, ms2840a rbw mode: normal for the ms2830a, ms2840a, rbw of 20 mhz and higher can be used only when ms2830a-00...

  • Page 1275

    Chapter ４ native device message details 4-193 4 n ati ve d ev ice m es sa ge d et ail s read:spur? Spurious emission read function this command performs the spurious emission measurement and queries the result. It works in the same way as the two commands are transmitted in the following order: init...

  • Page 1276

    Chapter ４ native device message details 4-194 acp measurement query and response query res? Res? Offset response lc(,1c),lr1,la1,ur1,ua1,lr2, la2,ur2,ua2,lr3,la3,ur3,ua3 lc reference power absolute value for acp reference lr1 offset channel 1 (bottom side) power relative value la1 offset channel 1 (...

  • Page 1277

    Chapter ４ native device message details 4-195 4 n ati ve d ev ice m es sa ge d et ail s lc12 absolute value of the power of carrier-12 the result of the carrier position greater than the carrier number set in acp carrier number is output as ***. Burst average power measurement query and response que...

  • Page 1278

    Chapter ４ native device message details 4-196 margin_lower_offset_4,freq_lower_offset_4, lower_offset_4,abs_upper_offset_4, margin_upper_offset_4,freq_upper_offset_4, upper_offset_4,abs_lower_offset_5, margin_lower_offset_5,freq_lower_offset_5, lower_offset_5,abs_upper_offset_5, margin_upper_offset_...

  • Page 1279

    Chapter ４ native device message details 4-197 4 n ati ve d ev ice m es sa ge d et ail s spurious emission measurement query and response query res? Response (when spurious emission result type is worst) judge,spur_1,range_1,freq_1,peak_1,margin_1,limit_1,j udge_1,spur_2,range,freq_2,peak_2,margin_2,...

  • Page 1280

    Chapter ４ native device message details 4-198 limit_n power value of the limit line of spurious only one value is returned when marker result type is worst. Values have no suffix code, are in dbm units, and have 0.01 db resolution. *** is returned when an error occurs/no measurement is performed. Ju...

  • Page 1281

    Chapter ４ native device message details 4-199 4 n ati ve d ev ice m es sa ge d et ail s respower? Power marker result query function this command queries the measurement results of the power marker function. Query respower? Type response pow1,den1 when type is mkr pow1 total power (/zone) in zone ma...

  • Page 1282

    Chapter ４ native device message details 4-200 pow_rel,den_rel when type is delta pow_rel ratio of the total power of delta marker (/zone) returns *** when marker mode of the marker set by relative to is set to fixed or off. Returns *** when zone width type of the marker set by relative to is set to ...

  • Page 1283

    Chapter ４ native device message details 4-201 4 n ati ve d ev ice m es sa ge d et ail s rfat/rfat? Set rf attenuator steps function this command sets the attenuator steps to 2 db or 10 db. Remarks this command is provided for backward compatibility. Setting will be ignored. Command rfat att query rf...

  • Page 1284

    Chapter ４ native device message details 4-202 rl/rl? Reference level function this command sets the reference level. Command rl level query rl? Response level no suffix code; a value is returned that conforms to scale unit setting. When the unit is v, µv is returned. When the unit is w, µw is return...

  • Page 1285

    Chapter ４ native device message details 4-203 4 n ati ve d ev ice m es sa ge d et ail s conforms to scale unit setting if omitted. V is used for linear scale. Details this is not available when spurious emission is on, and gate view is off. Example of use to set the reference level to 0 dbm rl 0 rl ...

  • Page 1286

    Chapter ４ native device message details 4-204 rlv/rlv? Reference level function this command sets the reference level. Command rlv level query rlv? Response level no suffix code. Value is returned according to the scale unit settings. Units are µv when v, and µw when w. Parameter level reference lev...

  • Page 1287

    Chapter ４ native device message details 4-205 4 n ati ve d ev ice m es sa ge d et ail s details this command is not available when spurious emission is set to on and when gate view is set to off. Example of use to set the reference level to 0 dbm. Rlv 0 rlv 0dbm rlv? > 0.00 rmk? Reference marker pos...

  • Page 1288

    Chapter ４ native device message details 4-206 rmkf? Reference marker frequency (time) query function this command queries the frequency or time of the marker point set by relative to of the active marker. Query rmkf? Response freq returns a value without a suffix code in hz units, and with a resolut...

  • Page 1289

    Chapter ４ native device message details 4-207 4 n ati ve d ev ice m es sa ge d et ail s rmkl? Reference marker level query function this command queries the level data of the marker point set by relative to of the active marker. Query rmkl? Response level level of the marker point set by relative to...

  • Page 1290

    Chapter ４ native device message details 4-208 roffset/roffset? Ref. Level offset value function this command sets the reference level offset function on/off and sets the offset value. Command roffset level roffset on_off query roffset? Response level when the reference level offset function is on of...

  • Page 1291

    Chapter ４ native device message details 4-209 4 n ati ve d ev ice m es sa ge d et ail s roffsetmd/roffsetmd? Reference level offset mode function this command sets the reference level offset function on/off. Command roffsetmd on_off query roffsetmd? Response on_off parameter on_off reference level o...

  • Page 1292

    Chapter ４ native device message details 4-210 scalelines/scalelines? Log scale line function this command sets the number of y-axis scale segments for log scale. Command scalelines line query scalelines? Response line parameter line number of y-axis scale segments 10 10 segments 12 12 segments detai...

  • Page 1293

    Chapter ４ native device message details 4-211 4 n ati ve d ev ice m es sa ge d et ail s scalemode/scalemode? Scale mode function this command switches the scale mode. Command scalemode mode query scalemode? Response scale parameter scale scale mode log log scale lin linear scale details when the sca...

  • Page 1294

    Chapter ４ native device message details 4-212 selectstd/selectstd? Select standard function this command selects parameter setting type for the measure function, using a communication standard. Command selectstd standard query selectstd? Response standard parameter standard communication standard of...

  • Page 1296

    Chapter ４ native device message details 4-214 sem:att/sem:att? Spectrum emission mask attenuator function this command sets attenuator in measuring the reference power for spectrum emission mask measurement. Command sem:att rel_ampl sem:att auto query sem:att? Response rel_ampl no suffix code. Value...

  • Page 1297

    Chapter ４ native device message details 4-215 4 n ati ve d ev ice m es sa ge d et ail s sem:band/sem:band? Spectrum emission mask resolution bandwidth function this command sets the resolution bandwidth (rbw) of the reference channel for spectrum emission mask measurement. Command sem:band bandwidth...

  • Page 1298

    Chapter ４ native device message details 4-216 sem:band:auto/sem:band:auto? Spectrum emission mask resolution bandwidth auto/manual function this command sets the resolution bandwidth (rbw) of the reference channel for spectrum emission mask measurement. Command sem:band:auto switch_com query sem:ban...

  • Page 1299

    Chapter ４ native device message details 4-217 4 n ati ve d ev ice m es sa ge d et ail s sem:band:chan/sem:band:chan? Spectrum emission mask integrate bandwidth function this command sets the measurement bandwidth of the reference power for spectrum emission mask measurement. Command sem:band:chan ba...

  • Page 1300

    Chapter ４ native device message details 4-218 sem:band:vid/sem:band:vid? Spectrum emission mask video bandwidth function this command sets the video bandwidth (vbw) in measuring the reference power for spectrum emission mask measurement. Command sem:band:vid bandwidth sem:band:vid off query sem:band...

  • Page 1301

    Chapter ４ native device message details 4-219 4 n ati ve d ev ice m es sa ge d et ail s sem:band:vid:auto/sem:band:vid:auto? Spectrum emission mask video bandwidth auto/manual function this command sets the video bandwidth (vbw) in measuring the reference power for spectrum emission mask measurement...

  • Page 1302

    Chapter ４ native device message details 4-220 sem:band:vid:mode/sem:band:vid:mode? Spectrum emission mask video bandwidth mode function this command sets the processing method for the video bandwidth(vbw) in measuring the reference power for spectrum emission mask measurement. Command sem:band:vid:m...

  • Page 1303

    Chapter ４ native device message details 4-221 4 n ati ve d ev ice m es sa ge d et ail s sem:carr/sem:carr? Spectrum emission mask reference power function this command sets the reference power for spectrum emission mask measurement. Command sem:carr ampl query sem:carr? Response ampl returns a value...

  • Page 1304

    Chapter ４ native device message details 4-222 sem:det/sem:det? Spectrum emission mask detection mode function this command selects the detection type of the waveform pattern in measuring the reference power for spectrum emission mask measurement. Command sem:det mode query sem:det? Response mode par...

  • Page 1305

    Chapter ４ native device message details 4-223 4 n ati ve d ev ice m es sa ge d et ail s sem:filt:alph/sem:filt:alph? Spectrum emission mask reference roll-off factor function this command sets the rolloff ratio of the filter in measuring the reference power for spectrum emission mask measurement. Co...

  • Page 1306

    Chapter ４ native device message details 4-224 sem:filt:type/sem:filt:type? Spectrum emission mask reference filter type function this command selects the filter type in measuring the reference power for spectrum emission mask measurement. Command sem:filt:type type query sem:filt:type? Response type...

  • Page 1307

    Chapter ４ native device message details 4-225 4 n ati ve d ev ice m es sa ge d et ail s sem:log:offs:list:test/sem:log:offs:list:test? Spectrum emission mask fail logic function this command selects the judgment method of the offset for spectrum emission mask measurement. Command sem:log:offs:list:t...

  • Page 1308

    Chapter ４ native device message details 4-226 and2 abs1 and abs2 judges “and” using the absolute level upper limit 1 and the absolute level upper limit 2. Example of use to judge using the absolute level upper limit 1. Sem:log:offs:list:test abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs,abs sem:log:of...

  • Page 1309

    Chapter ４ native device message details 4-227 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:att/sem:offs:list:att? Spectrum emission mask offset attenuator function this command sets the attenuator value in measuring the offset for spectrum emission mask measurement. Command sem:offs:list:...

  • Page 1310

    Chapter ４ native device message details 4-228 sem:offs:list:band/sem:offs:list:band? Spectrum emission mask offset resolution bandwidth function this command sets the resolution bandwidth (rbw) of the offset for spectrum emission mask measurement. Command sem:offs:list:band bandwidth_1[,bandwidth_2[...

  • Page 1311

    Chapter ４ native device message details 4-229 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the resolution bandwidth of the offset. Sem:offs:list:band 30khz,30khz,30khz,1mhz,1mhz,1mhz,30khz,30khz,30khz,1mhz, 1mhz,1mhz sem:offs:list:band? > 30000,30000,30000,1000000,1000000,1000000,...

  • Page 1312

    Chapter ４ native device message details 4-230 details the setting range of this function is limited depending on the settings of other parameters. Refer to ms2690a/ms2691a/ms2692a signal analyzer operation manual(spectrum analyzer function operation) or ms2830a/ms2840a signal analyzer operation manu...

  • Page 1313

    Chapter ４ native device message details 4-231 4 n ati ve d ev ice m es sa ge d et ail s parameter bandwidth_n integrate bw of offset-n range 30 hz to 20 mhz resolution integrate bw is as below. 1 hz (30 hz to 1 khz) 10 hz (1 to 10 khz) 100 hz (10 to 100 khz) 1 khz (100 khz to 1 mhz) 10 khz (1 to 20 ...

  • Page 1314

    Chapter ４ native device message details 4-232 sem:offs:list:band:int:auto/sem:offs:list:band:int:auto? Spectrum emission mask offset integrate bandwidth auto/manual function this command sets integrate bw of the offset for spectrum emission mask measurement automatically. Command sem:offs:list:band:...

  • Page 1315

    Chapter ４ native device message details 4-233 4 n ati ve d ev ice m es sa ge d et ail s example of use to set integrate bw of the offset automatically. Sem:offs:list:band:int:auto on,on,on,on,on,on,on,on,on,on,on,on sem:offs:list:band:int:auto? > 1,1,1,1,1,1,1,1,1,1,1,1 sem:offs:list:band:vid/sem:of...

  • Page 1316

    Chapter ４ native device message details 4-234 example of use to set the video bandwidth of the offset. Sem:offs:list:band:vid 3khz,3khz,3khz,10khz,10khz,10khz,3khz,3khz,3khz,10khz,10 khz,10khz sem:offs:list:band:vid? > 3000,3000,3000,10000,10000,10000,3000,3000,3000,10000,10 000,10000 sem:offs:list:...

  • Page 1317

    Chapter ４ native device message details 4-235 4 n ati ve d ev ice m es sa ge d et ail s details the setting range of this function is limited depending on the settings of other parameters. Refer to ms2690a/ms2691a/ms2692a signal analyzer operation manual(spectrum analyzer function operation) or ms28...

  • Page 1318

    Chapter ４ native device message details 4-236 sem:offs:list:det/sem:offs:list:det? Spectrum emission mask offset detection mode function this command selects the detection type of the waveform pattern of the offset for spectrum emission mask measurement. Command sem:offs:list:det mode_1[,mode_2[,mod...

  • Page 1319

    Chapter ４ native device message details 4-237 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:freq:star/sem:offs:list:freq:star? Spectrum emission mask offset start frequency function this command sets the start frequency of the offset for spectrum emission mask measurement. Command sem:offs...

  • Page 1320

    Chapter ４ native device message details 4-238 sem:offs:list:freq:stop/sem:offs:list:freq:stop? Spectrum emission mask offset stop frequency function this command sets the stop frequency of the offset for spectrum emission mask measurement. Command sem:offs:list:freq:stop freq_1[,freq_2[,freq_3[,freq...

  • Page 1321

    Chapter ４ native device message details 4-239 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:rlev/sem:offs:list:rlev? Spectrum emission mask offset reference level function this command sets the reference level of the offset for spectrum emission mask measurement. Command sem:offs:list:rlev...

  • Page 1322

    Chapter ４ native device message details 4-240 sem:offs:list:rlev:auto/sem:offs:list:rlev:auto? Spectrum emission mask offset reference level auto/manual function this command sets the reference level of the offset for spectrum emission mask measurement automatically. Command sem:offs:list:rlev:auto ...

  • Page 1323

    Chapter ４ native device message details 4-241 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:star:abs/sem:offs:list:star:abs? Spectrum emission mask offset start frequency absolute limit level function this command sets the absolute level upper limit of the offset start frequency for spectr...

  • Page 1324

    Chapter ４ native device message details 4-242 sem:offs:list:star:rcar/sem:offs:list:star:rcar? Spectrum emission mask offset start frequency limit level function this command sets the relative level limit of the offset start frequency for spectrum emission mask measurement. Command sem:offs:list:sta...

  • Page 1325

    Chapter ４ native device message details 4-243 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:stat/sem:offs:list:stat? Spectrum emission mask offset on/off function this command sets the offset for spectrum emission mask measurement on/off. Command sem:offs:list:stat switch_1_com[,switch_2_c...

  • Page 1326

    Chapter ４ native device message details 4-244 sem:offs:list:stop:abs/sem:offs:list:stop:abs? Spectrum emission mask offset stop frequency absolute limit level function this command sets the absolute level upper limit of the offset stop frequency for spectrum emission mask measurement. Command sem:of...

  • Page 1327

    Chapter ４ native device message details 4-245 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:stop:rcar/sem:offs:list:stop:rcar? Spectrum emission mask offset stop frequency limit level function this command sets the relative level upper limit of the offset stop frequency for spectrum emissi...

  • Page 1328

    Chapter ４ native device message details 4-246 sem:offs:list:swe:poin/sem:offs:list:swe:poin? Spectrum emission mask offset trace point function this command sets the number of the frequency points of the offset for spectrum emission mask measurement. Command sem:offs:list:swe:poin integer_1[,integer...

  • Page 1329

    Chapter ４ native device message details 4-247 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:swe:time/sem:offs:list:swe:time? Spectrum emission mask offset sweep time function this command sets the sweep time of the offset for spectrum emission mask measurement. Command sem:offs:list:swe:ti...

  • Page 1330

    Chapter ４ native device message details 4-248 example of use to set the sweep time of the offset. Sem:offs:list:swe:time 40ms,40ms,40ms,40ms,40ms,40ms,40ms,40ms,40ms,40ms,40ms,4 0ms sem:offs:list:swe:time? > 0.040000,0.040000,0.040000,0.040000,0.040000,0.040000,0. 040000,0.040000,0.040000,0.040000,0...

  • Page 1331

    Chapter ４ native device message details 4-249 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:swe:time:auto/sem:offs:list:swe:time:auto? Spectrum emission mask offset sweep time auto/manual function this command sets the sweep time of the offset for spectrum emission mask measurement automat...

  • Page 1332

    Chapter ４ native device message details 4-250 sem:offs:list:swe:time:auto:mode/sem:offs:list:swe:time:aut o:mode? Spectrum emission mask offset auto sweep time select function this command sets the normal/fast mode in the case that the sweep time of the offset for spectrum emission mask measurement ...

  • Page 1333

    Chapter ４ native device message details 4-251 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:list:swe:rul:fft:rwid? Spectrum emission mask offset sweep type select rules real fft width query function this command queries the fft width that is actually used for the sweep/fft switch rule during of...

  • Page 1334

    Chapter ４ native device message details 4-252 sem:offs:list:swe:rul:rtyp? Spectrum emission mask sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during reference power measurement in the spectrum emission mask measurement. Query se...

  • Page 1335

    Chapter ４ native device message details 4-253 4 n ati ve d ev ice m es sa ge d et ail s sem:offs:side/sem:offs:side? Spectrum emission mask limit side function this command selects the judging area for spectrum emission mask measurement. Command sem:offs:side side query sem:offs:side? Response side ...

  • Page 1336

    Chapter ４ native device message details 4-254 sem:rac/sem:rac? Couple ref & att function this command enables/disables sharing of the reference level and attenuator settings for the spectrum emission mask measurement. Command sem:rac switch_com query sem:rac? Response switch_res parameter switch_com...

  • Page 1337

    Chapter ４ native device message details 4-255 4 n ati ve d ev ice m es sa ge d et ail s sem:swe:poin/sem:swe:poin? Spectrum emission mask trace point function this command selects the frequency display point in measuring the reference power for spectrum emission mask measurement. Command sem:swe:poi...

  • Page 1338

    Chapter ４ native device message details 4-256 sem:swe:rul:fft:rwid? Spectrum emission mask sweep type select rules real fft width query function this command queries the fft width that is actually used for the sweep/fft switch rule during reference power measurement in the spectrum emission mask mea...

  • Page 1339

    Chapter ４ native device message details 4-257 4 n ati ve d ev ice m es sa ge d et ail s sem:swe:rul:rtyp? Spectrum emission mask sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during reference power measurement in the spectrum emi...

  • Page 1340

    Chapter ４ native device message details 4-258 sem:swe:time/sem:swe:time? Spectrum emission mask sweep time function this command sets the sweep time in measuring the reference power for spectrum emission mask measurement. Command sem:swe:time time query sem:swe:time? Response time returns a value of...

  • Page 1341

    Chapter ４ native device message details 4-259 4 n ati ve d ev ice m es sa ge d et ail s sem:swe:time:auto/sem:swe:time:auto? Spectrum emission mask sweep time auto/manual function this command sets the sweep time in measuring the reference power for spectrum emission mask measurement. Command sem:sw...

  • Page 1342

    Chapter ４ native device message details 4-260 sem:swe:time:auto:mode/sem:swe:time:auto:mode? Spectrum emission mask auto sweep time select function this command sets the normal/fast mode in the case that the sweep time in measuring the reference power for spectrum emission mask measurement is auto. ...

  • Page 1343

    Chapter ４ native device message details 4-261 4 n ati ve d ev ice m es sa ge d et ail s sem:type/sem:type? Spectrum emission mask reference type function this command sets the reference for spectrum emission mask measurement. Command sem:type type query sem:type? Response type parameter type type of...

  • Page 1344

    Chapter ４ native device message details 4-262 sigid/sigid? Signal identifier function this command enables/disables signal identifier operation, which identifies measured signal and image signal when external mixer is used. Command sigid switch query sigid? Response switch parameter switch signal id...

  • Page 1345

    Chapter ４ native device message details 4-263 4 n ati ve d ev ice m es sa ge d et ail s sma/sma? Write and query trace data (trace a) function this command writes and queries the trace data of trace a. This function targets negative detection trace data when the detection mode is positive & negative...

  • Page 1346

    Chapter ４ native device message details 4-264 smb/smb? Write and query trace data (trace b) function this command writes and queries the trace data of trace b. This function targets negative detection trace data when the detection mode is positive & negative (normal mode). Command smb wpoint,data qu...

  • Page 1347

    Chapter ４ native device message details 4-265 4 n ati ve d ev ice m es sa ge d et ail s smc/smc? Write and query trace data (trace c) function this command writes and queries the trace data of trace c. This function targets negative detection trace data when the detection mode is positive & negative...

  • Page 1348

    Chapter ４ native device message details 4-266 smd/smd? Write and query trace data (trace d) function this command writes and queries the trace data of trace d. This function targets negative detection trace data when the detection mode is positive & negative (normal mode). Command smd wpoint,data qu...

  • Page 1349

    Chapter ４ native device message details 4-267 4 n ati ve d ev ice m es sa ge d et ail s example of use to set –20 dbm at the first point and set –21 dbm at the second point. Smd 1,-20000 smd 2,-21000 smd? 1,2 > -20000,-21000 sme/sme? Write and query trace data (trace e) function this command writes ...

  • Page 1350

    Chapter ４ native device message details 4-268 details this command is not available in the following cases: • during the spectrum emission mask measurement. • during the spurious emission measurement. Example of use to set −20 dbm at the first point and set −21 dbm at the second point. Sme 1,-20000 ...

  • Page 1351

    Chapter ４ native device message details 4-269 4 n ati ve d ev ice m es sa ge d et ail s range 0 to 10, 20, 40, 50, 100, 200, 250, 400, 500, 1000, 2000, 5000, 10000, 30000 (ms269xa only) number number of items of data to be loaded range 1 to 11, 21, 41, 51, 101, 201, 251, 401, 501, 1001, 2001, 5001, ...

  • Page 1352

    Chapter ４ native device message details 4-270 smz/smz? Write and query trace data (gate view) function this command writes and queries the trace data for gate view. This command targets negative detection trace data when the detection mode is positive & negative (normal mode). Command smz wpoint,dat...

  • Page 1353

    Chapter ４ native device message details 4-271 4 n ati ve d ev ice m es sa ge d et ail s sngls single sweep mode function this command sets the sweep mode to single and start the single sweep. Command sngls details starting sweep with this function executes the following command during sweep. To read...

  • Page 1354

    Chapter ４ native device message details 4-272 sof/sof? Stop frequency function this command sets the stop frequency. Command sof freq query sof? Response freq returns a value in hz units, without a suffix code. Parameter freq stop frequency range [ms269xa] –99.999700 mhz to 6.05 ghz (ms2690a) –99.99...

  • Page 1355

    Chapter ４ native device message details 4-273 4 n ati ve d ev ice m es sa ge d et ail s spf/spf? Frequency span function this command sets the frequency span. Command spf freq query spf? Response freq no suffix code. Value is returned in hz units. Parameter freq frequency span range [ms269xa] 0 hz, ...

  • Page 1356

    Chapter ４ native device message details 4-274 spf 123456hz spf 123.456khz spf 0.123456mhz spf? > 123456.

  • Page 1359

    Chapter ４ native device message details 4-277 4 n ati ve d ev ice m es sa ge d et ail s spur:aver:coun/spur:aver:coun? Spurious emission storage count function this command sets the storage count of each segment. Command spur:aver:coun integer_1,integer_2,integer_3,integer_4,integer_5,intege r_6,int...

  • Page 1360

    Chapter ４ native device message details 4-278 spur:aver:coun:coup/spur:aver:coun:coup? Couple storage count function this command sets the shared setting of the storage count in each segment to on/off. Command spur:aver:coun:coup switch_com query spur:aver:coun:coup? Response switch_res parameter sw...

  • Page 1361

    Chapter ４ native device message details 4-279 4 n ati ve d ev ice m es sa ge d et ail s spur:band/spur:band? Spurious emission resolution bandwidth function this command sets the resolution bandwidth (rbw) of each segment. Command spur:band bandwidth_1,bandwidth_2,bandwidth_3,bandwidth_4,bandwidt h_...

  • Page 1362

    Chapter ４ native device message details 4-280 10000 spur:band:auto/spur:band:auto? Spurious emission resolution bandwidth auto/manual function this command sets rbw of each segment to auto/manual. Command spur:band:auto switch_1_com,switch_2_com,switch_3_com,switch_4_com,swit ch_5_com,switch_6_com,s...

  • Page 1364

    Chapter ４ native device message details 4-282 example of use to set the video bandwidth of each segment. Spur:band:vid 3khz,3khz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1 mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz spur:band:vid? > 3000,3000,1000000,1000000,1000000,1000000,1000000,100000 0,1000...

  • Page 1365

    Chapter ４ native device message details 4-283 4 n ati ve d ev ice m es sa ge d et ail s spur:band:vid:auto/spur:band:vid:auto? Spurious emission video bandwidth auto/manual function this command sets the video bandwidth (vbw) of each segment to auto/manual. Command spur:band:vid:auto switch_1_com,sw...

  • Page 1366

    Chapter ４ native device message details 4-284 spur:det/spur:det? Spurious emission detection mode function this command selects the detection mode of the waveform pattern in each segment. Command spur:det mode_1,mode_2,mode_3,mode_4,mode_5,mode_6,mode_7,mode_8, mode_9,mode_10,mode_11,mode_12,mode_13...

  • Page 1367

    Chapter ４ native device message details 4-285 4 n ati ve d ev ice m es sa ge d et ail s spur:freq:star/spur:freq:star? Spurious emission start frequency function this command sets the start frequency of each segment. Command spur:freq:star freq_1,freq_2,freq_3,freq_4,freq_5,freq_6,freq_7,freq_8, fre...

  • Page 1368

    Chapter ４ native device message details 4-286 > 9000,100000,40000000,11000000000,1000000000,1000000000,1 000000000,1000000000,1000000000,1000000000,1000000000,10 00000000,1000000000,1000000000,1000000000,1000000000,100 0000000,1000000000,1000000000,1000000000 spur:freq:stop/spur:freq:stop? Spurious ...

  • Page 1369

    Chapter ４ native device message details 4-287 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the stop frequency of each segment. Spur:freq:stop 150khz,40mhz,1.1ghz,12.5ghz,12.5ghz,12.5ghz,12.5ghz,12.5 ghz,12.5ghz,12.5ghz,12.5ghz,12.5ghz,12.5ghz,12.5ghz,12.5 ghz,12.5ghz,12.5ghz,12.5g...

  • Page 1370

    Chapter ４ native device message details 4-288 example of use to stop the measurement when a “fail” segment has been found. Spur:fst on spur:fst? > 1 spur:peak:res/spur:peak:res? Spurious emission search resolution function this command sets the spurious search resolution when result type is set to p...

  • Page 1371

    Chapter ４ native device message details 4-289 4 n ati ve d ev ice m es sa ge d et ail s spur:peak:thr/spur:peak:thr? Spurious emission search threshold level function this command sets the spurious search threshold when result type is peak. Command spur:peak:thr real_1,real_2,real_3,real_4,real_5,re...

  • Page 1372

    Chapter ４ native device message details 4-290 spur:pow:gain/spur:pow:gain? Spurious emission preamp on/off function this command sets the pre-amp of each segment to on/off. Command spur:pow:gain switch_1_com,switch_2_com,switch_3_com,switch_4_com,swit ch_5_com,switch_6_com,switch_7_com,switch_8_com,...

  • Page 1373

    Chapter ４ native device message details 4-291 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the pre-amp of each segment. Spur:pow:gain on,on,on,off,off,on,on,on,on,off,off,on,on,on,on,off,off ,on,on,on spur:pow:gain? > 1,1,1,0,0,1,1,1,1,0,0,1,1,1,1,0,0,1,1,1 spur:segm:numb/spur:seg...

  • Page 1374

    Chapter ４ native device message details 4-292 spur:segm:stat/spur:segm:stat? Segment on/off function this command sets the segment to on/off. Command spur:segm:stat switch_1_com,switch_2_com,switch_3_com,switch_4_com,swit ch_5_com,switch_6_com,switch_7_com,switch_8_com,switch_9 _com,switch_10_com,sw...

  • Page 1375

    Chapter ４ native device message details 4-293 4 n ati ve d ev ice m es sa ge d et ail s spur:swe:paus/spur:swe:paus? Pause before sweep function this command configures the setting to pause before sweep of each segment. Command spur:swe:paus switch_1_com,switch_2_com,switch_3_com,switch_4_com,swit c...

  • Page 1376

    Chapter ４ native device message details 4-294 example of use to configure the setting to pause before sweep of each segment. Spur:swe:paus on,on,on,off,off,on,on,on,on,off,off,on,on,on,on,off,off ,on,on,on spur:swe:paus? > 1,1,1,0,0,1,1,1,1,0,0,1,1,1,1,0,0,1,1,1 spur:swe:poin/spur:swe:poin? Spurious...

  • Page 1377

    Chapter ４ native device message details 4-295 4 n ati ve d ev ice m es sa ge d et ail s 1001 1001 points 2001 2001 points 5001 5001 points 10001 10001 points 30001 30001 points (ms269xa only) example of use to set the number of the points in the trace data of each segment. Spur:swe:poin 1001,5001,50...

  • Page 1378

    Chapter ４ native device message details 4-296 spur:swe:time/spur:swe:time? Spurious emission sweep time function this command sets the sweep time of each segment. Command spur:swe:time seconds_1,seconds_2,seconds_3,seconds_4,seconds_5,second s_6,seconds_7,seconds_8,seconds_9,seconds_10,seconds_11, s...

  • Page 1379

    Chapter ４ native device message details 4-297 4 n ati ve d ev ice m es sa ge d et ail s spur:swe:time:auto/spur:swe:time:auto? Spurious emission sweep time auto/manual function this command sets the sweep time of each segment to auto/manual. Command spur:swe:time:auto switch_1_com,switch_2_com,switc...

  • Page 1380

    Chapter ４ native device message details 4-298 spur:synt:lph/spur:synt:lph? Low phase noise for spurious emission measurement function this command enables/disables low phase noise function during spurious emission measurement. Command spur:synt:lph switch query spur:synt:lph? Response switch paramet...

  • Page 1381

    Chapter ４ native device message details 4-299 4 n ati ve d ev ice m es sa ge d et ail s generation and appropriate conditions for using the low phase noise function. Example of use to enable the low phase noise function during spurious emission measurement. Spur:synt:lph on spur:synt:lph? > 1.

  • Page 1382

    Chapter ４ native device message details 4-300 spur:tdom:band/spur:tdom:band? Spurious emission time domain rbw function this command sets rbw when performing time domain measurement. Command spur:tdom:band bandwidth_1,bandwidth_2,bandwidth_3,bandwidth_4,bandwidt h_5,bandwidth_6,bandwidth_7,bandwidth...

  • Page 1383

    Chapter ４ native device message details 4-301 4 n ati ve d ev ice m es sa ge d et ail s example of use to set rbw when performing time domain measurement. Spur:tdom:band 3khz,3khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10kh z,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz,10khz, 10khz spur:tdom:...

  • Page 1384

    Chapter ４ native device message details 4-302 spur:tdom:band:coup/spur:tdom:band:coup? Spurious emission couple segment rbw function this command enables/disables the function that the value set in segment setup is automatically set to rbw when performing time domain measurement. Command spur:tdom:b...

  • Page 1386

    Chapter ４ native device message details 4-304 example of use to set vbw when performing time domain measurement. Spur:tdom:band:vid 3khz,3khz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1 mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz,1mhz spur:tdom:band:vid? > 3000,3000,1000000,1000000,1000000,1000000,100...

  • Page 1387

    Chapter ４ native device message details 4-305 4 n ati ve d ev ice m es sa ge d et ail s spur:tdom:band:vid:coup/spur:tdom:band:vid:coup? Spurious emission couple segment vbw function this command enables/disables the function that the value set in segment setup is automatically set to vbw when perfo...

  • Page 1388

    Chapter ４ native device message details 4-306 spur:tdom:det/spur:tdom:det? Spurious emission time domain detection function this command selects the detection mode of the waveform pattern when performing time domain measurement. Command spur:tdom:det mode_1,mode_2,mode_3,mode_4,mode_5,mode_6,mode_7,...

  • Page 1389

    Chapter ４ native device message details 4-307 4 n ati ve d ev ice m es sa ge d et ail s spur:tdom:span:zero/spur:tdom:span:zero? Time domain measurement function this command sets whether to measure the spurious power by using time domain. Command spur:tdom:span:zero switch_com query spur:tdom:span:...

  • Page 1390

    Chapter ４ native device message details 4-308 spur:tdom:swe:time/spur:tdom:swe:time? Spurious emission time domain sweep time function this command sets the sweep time when performing time domain measurement. Command spur:tdom:swe:time seconds_1,seconds_2,seconds_3,seconds_4,seconds_5,second s_6,sec...

  • Page 1391

    Chapter ４ native device message details 4-309 4 n ati ve d ev ice m es sa ge d et ail s spur:type/spur:type? Spurious emission result type function this command selects the measurement result type. Command spur:type type_com query spur:type? Response type_res parameter type_com measurement result ty...

  • Page 1392

    Chapter ４ native device message details 4-310 srchth/srchth? Peak search mode function this command specifies the detection mode for the threshold value (peak search threshold level) in peak point detection. Command srchth mode query srchth? Response mode parameter mode threshold value detection mod...

  • Page 1393

    Chapter ４ native device message details 4-311 4 n ati ve d ev ice m es sa ge d et ail s srchthlvl/srchthlvl? Peak search threshold level function this command sets the threshold value when detecting a peak point. Command srchthlvl level query srchthlvl? Response level returns a value according to th...

  • Page 1394

    Chapter ４ native device message details 4-312 details this command is not available during the spurious emission measurement and when displayed segment mode is set to auto. Not available during spectrum emission mask measurement. Example of use to set the threshold value when detecting peak point to...

  • Page 1395

    Chapter ４ native device message details 4-313 4 n ati ve d ev ice m es sa ge d et ail s auto sets the optimum value from rbw, wbw and span. Details this command is not available during fft sweep. This command is not available during the spectrum emission mask or the spurious emission measurement. Th...

  • Page 1396

    Chapter ４ native device message details 4-314 stf/stf? Start frequency function this command sets the start frequency. Command stf freq query stf? Response freq returns a value in hz units, without a suffix code. Parameter freq start frequency range [ms269xa] –100 mhz to 6.0499997 ghz (ms2690a) –100...

  • Page 1397

    Chapter ４ native device message details 4-315 4 n ati ve d ev ice m es sa ge d et ail s stmode/stmode? Auto sweep time mode function this command sets normal/fast mode when sweep time is auto. Command stmode mode query stmode? Response mode parameter mode sweep time normal normal sweep time fast fas...

  • Page 1398

    Chapter ４ native device message details 4-316 storagecount/storagecount? Storage count function this command sets the storage mode count. Command storagecount count query storagecount? Response count parameter count storage mode count range 2 to 9999 details this command is not available during the ...

  • Page 1399

    Chapter ４ native device message details 4-317 4 n ati ve d ev ice m es sa ge d et ail s storagemode/storagemode? Storage mode (active trace) function this command selects the storage mode of the active trace. Command storagemode mode query storagemode? Response mode parameter mode storage mode off o...

  • Page 1400

    Chapter ４ native device message details 4-318 svcsvwave save wave data function this command saves waveform data into a csv file. Command svcsvwave file,device parameter file name of file to be saved character string within 32 characters enclosed by double quotes (" ") or single quotes (' '). (exclu...

  • Page 1401

    Chapter ４ native device message details 4-319 4 n ati ve d ev ice m es sa ge d et ail s sweepcount? Sweep count function this command queries the sweep count. Query sweepcount? Response count sweep count range 0 to 9999 details during the spectrum emission mask measurement, the sweep count is displa...

  • Page 1402

    Chapter ４ native device message details 4-320 swe:egat:hold/swe:egat:hold? Gate hold function this command sets the time during which gate input is disabled for a set time, from the first gate input signal until the next gate signal input, during gate sweep. Command swe:egat:hold time query swe:egat...

  • Page 1403

    Chapter ４ native device message details 4-321 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:hold:stat/swe:egat:hold:stat? Gate hold on/off function this command switches on/off the function to disable gate input for a set time, from the first gate input signal until the next gate signal input, ...

  • Page 1404

    Chapter ４ native device message details 4-322 swe:egat:time/swe:egat:time? Gate view sweep time function this command sets the sweep time for gate view. This parameter and the one for setting the sweep time for time axis measurement reference the same value. Command swe:egat:time time query swe:egat...

  • Page 1405

    Chapter ４ native device message details 4-323 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:view/swe:egat:view? Gate view function this command sets whether to display the gate view. Command swe:egat:view switch_com query swe:egat:view? Response switch_res parameter switch_com displays or hides...

  • Page 1406

    Chapter ４ native device message details 4-324 swe:egat:view:band/swe:egat:view:band? Gate view resolution bandwidth function this command sets the resolution bandwidth (rbw) for gate view. This parameter and the one for setting the rbw for time axis measurement reference the same value. Command swe:...

  • Page 1407

    Chapter ４ native device message details 4-325 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:view:band:auto/swe:egat:view:band:auto? Gate view resolution bandwidth auto/manual function this command automatically sets the resolution bandwidth (rbw) for gate view. This parameter and the one for au...

  • Page 1408

    Chapter ４ native device message details 4-326 swe:egat:view:band:vid/swe:egat:view:band:vid? Gate view video bandwidth function this command sets the video bandwidth (vbw) for gate view. This parameter and the one for setting the vbw for time axis measurement reference the same value. Command swe:eg...

  • Page 1409

    Chapter ４ native device message details 4-327 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:view:band:vid:auto/swe:egat:view:band:vid:auto? Gate view video bandwidth auto/manual function this command automatically sets the video bandwidth (vbw) for gate view. This parameter and the one for sett...

  • Page 1410

    Chapter ４ native device message details 4-328 swe:egat:view:det/swe:egat:view:det? Gate view detection mode function this command selects the waveform pattern detection mode for gate view. This parameter and the one for setting the waveform pattern detection mode for time axis measurement reference ...

  • Page 1411

    Chapter ４ native device message details 4-329 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:view:freq/swe:egat:view:freq? Gate view frequency function this command sets the center frequency for gate view. Command swe:egat:view:freq freq query swe:egat:view:freq? Response freq parameter freq cen...

  • Page 1412

    Chapter ４ native device message details 4-330 swe:egat:view:freq:auto/swe:egat:view:freq:auto? Gate view frequency mode function this command selects the center frequency setting mode for gate view. Command swe:egat:view:freq:auto switch_com query swe:egat:view:freq:auto? Response switch_res paramet...

  • Page 1413

    Chapter ４ native device message details 4-331 4 n ati ve d ev ice m es sa ge d et ail s swe:egat:view:poin/swe:egat:view:poin? Gate view trace point function this command sets the number of trace display points for gate view. This parameter and the one for setting the number of trace display points ...

  • Page 1414

    Chapter ４ native device message details 4-332 swe:rul/swe:rul? Auto sweep type select rules function this command sets the rule for switching between sweep and fft during measurement. Command swe:rul rules query swe:rul? Parameter rules switching rules dran selects sweep/fft prioritizing dynamic ran...

  • Page 1415

    Chapter ４ native device message details 4-333 4 n ati ve d ev ice m es sa ge d et ail s example of use to give priority to dynamic range for the sweep/fft switch rule. Swe:rul dran swe:rul? > dran swe:rul:fft:rwid? Sweep type select rules real fft width query function this command queries the fft wi...

  • Page 1416

    Chapter ４ native device message details 4-334 swe:rul:fft:widt/swe:rul:fft:widt? Sweep type select rules fft width function this command sets the fft width when fft priority is selected, for the sweep/fft switching rules during measurement. Command swe:rul:fft:widt freq query swe:rul:fft:widt? Param...

  • Page 1417

    Chapter ４ native device message details 4-335 4 n ati ve d ev ice m es sa ge d et ail s swe:rul:rtyp? Sweep type select rules real type query function this command queries the sweep mode (sweep or fft) that is executed during measurement. Query swe:rul:rtyp? Response type parameter type sweep mode s...

  • Page 1418

    Chapter ４ native device message details 4-336 swp/swp? Single sweep/sweep status query function this command sets the sweep mode to single and starts single sweep. Also, it reads the sweep status (sweep done/during sweeping). Command swp query swp? Response status sweep status 0 sweep done 1 during ...

  • Page 1419

    Chapter ４ native device message details 4-337 4 n ati ve d ev ice m es sa ge d et ail s swstart restart sweep function this command restarts the sweep. Command swstart example of use to restart sweep. Swstart swstop stop sweep function this command stops the sweep. Command swstop example of use to s...

  • Page 1420

    Chapter ４ native device message details 4-338 tdly/tdly? Trigger delay function this command sets the delay from the trigger occurrence point to sweep start. Command tdly time query tdly? Response time no suffix code. Value is returned in µs units. Parameter time delay time to start gating range –1 ...

  • Page 1421

    Chapter ４ native device message details 4-339 4 n ati ve d ev ice m es sa ge d et ail s title/title? Register title function this command registers the title character string. Command title string query title? Response string parameter string character string within 32 characters enclosed by double ...

  • Page 1422

    Chapter ４ native device message details 4-340 trac:sem? Query trace data spectrum emission mask function this function reads the trace data for spectrum emission mask measurement. Query trac:sem? Trace response data_1,data_2,... Parameter trace trace to save ref reference trace low1 offset1 lower si...

  • Page 1423

    Chapter ４ native device message details 4-341 4 n ati ve d ev ice m es sa ge d et ail s trac:sem:neg? Query negative trace data spectrum emission mask function this function reads the negative spectrum emission mask trace data when the detection mode is pos&neg (normal mode). Query trace:sem:neg? Tr...

  • Page 1424

    Chapter ４ native device message details 4-342 trglvl/trglvl? Trigger level function this command sets the threshold value of the level where trigger sweep starts. Command trglvl level query trglvl? Response level no suffix code. Refer to the parameters below for numerical values. Parameter level thr...

  • Page 1425

    Chapter ４ native device message details 4-343 4 n ati ve d ev ice m es sa ge d et ail s example of use to set the threshold value of the level where trigger sweep starts to –10 dbm. Trglvl -10dbm trglvl? > -10 trgs/trgs? Trigger switch function this command sets trigger sweep on/off. Command trgs sw...

  • Page 1426

    Chapter ４ native device message details 4-344 trgslp/trgslp? Trigger slope function this command sets the trigger detection mode (rise/fall). Command trgslp edge query trgslp? Response edge parameter edge trigger detection mode rise detects at the rising edge. Fall detects at the falling edge. Detai...

  • Page 1427

    Chapter ４ native device message details 4-345 4 n ati ve d ev ice m es sa ge d et ail s trgsource/trgsource? Trigger source function this command selects trigger source. Command trgsource source query trgsource? Response source parameter source trigger signal source [ms269xa] vid video detection (vi...

  • Page 1428

    Chapter ４ native device message details 4-346 trig:fram:offs/trig:fram:offs? Frame sync offset function this command sets the offset time from frame trigger occurrence signal source input until the frame trigger occurrence. Command trig:fram:offs time query trig:fram:offs? Parameter time offset time...

  • Page 1429

    Chapter ４ native device message details 4-347 4 n ati ve d ev ice m es sa ge d et ail s trig:fram:per/trig:fram:per? Frame trigger period function this command sets the trigger occurrence period of the frame trigger. Command trig:fram:per time query trig:fram:per? Parameter time frame trigger range ...

  • Page 1430

    Chapter ４ native device message details 4-348 trig:fram:sync/trig:fram:sync? Frame sync source function this command selects the synchronized signal source for frame trigger start. Command trig:fram:sync sync query trig:fram:sync? Parameter sync synchronized signal source ext external input (default...

  • Page 1431

    Chapter ４ native device message details 4-349 4 n ati ve d ev ice m es sa ge d et ail s trig:hold/trig:hold? Trigger hold function this command sets the time during which trigger input is disabled for a set time, from the first trigger input until the next trigger input. Command trig:hold time query...

  • Page 1432

    Chapter ４ native device message details 4-350 trig:hold:stat/trig:hold:stat? Trigger hold on/off function this command sets on/off the function to disable trigger input for a set time, from the first trigger input until the next trigger input. Command trig:hold:stat switch_com query trig:hold:stat? ...

  • Page 1433

    Chapter ４ native device message details 4-351 4 n ati ve d ev ice m es sa ge d et ail s ts single sweep function this command sets the sweep mode to single and starts single sweep. Command ts details starting sweep with this function makes the following command wait without being processed until swe...

  • Page 1434

    Chapter ４ native device message details 4-352 tslinavg linear average sweep function this command sets storage mode to linear average and starts sweep. Command tslinavg details starting sweep with this function makes the following command wait without being processed until sweep is finished. Example...

  • Page 1435

    Chapter ４ native device message details 4-353 4 n ati ve d ev ice m es sa ge d et ail s tsminhold min hold sweep function this command sets the storage mode to min hold and starts sweep. Command tsminhold details starting sweep with this function makes the following command wait without being proces...

  • Page 1436

    Chapter ４ native device message details 4-354 ucl? Uncal status query function this command queries the uncal status. Query ucl? Response status parameter status uncal status 0 normal 1 uncal example of use to query the uncal status. Ucl? > 1.

  • Page 1437

    Chapter ４ native device message details 4-355 4 n ati ve d ev ice m es sa ge d et ail s unc/unc? Display uncal message function this command displays/hides uncal messages at uncal. Command unc on_off query unc? Response on_off parameter on_off uncal display on/off on displays uncal. Off hides uncal....

  • Page 1438

    Chapter ４ native device message details 4-356 vavg/vavg? Average mode (active trace) function this command sets the active trace average processing to on/off and also sets the average count. Command vavg on_off vavg count query vavg? Response count parameter on_off average processing on/off on on of...

  • Page 1439

    Chapter ４ native device message details 4-357 4 n ati ve d ev ice m es sa ge d et ail s vb/vb? Video bandwidth function this command sets the video bandwidth (vbw). When couple time/frequency domain is set to off, each parameter is specified in accordance with the already-specified frequency axis or...

  • Page 1440

    Chapter ４ native device message details 4-358 vbwmode/vbwmode? Video bandwidth mode function this command sets the processing mode of the video bandwidth (vbw). Command vbwmode mode query vbwmode? Response mode parameter mode video bandwidth (vbw) processing mode video normal vbw power power vbw det...

  • Page 1441

    Chapter ４ native device message details 4-359 4 n ati ve d ev ice m es sa ge d et ail s writemode/writemode? Trace write mode function this command sets the writing mode of the active trace. Command writemode mode query writemode? Response mode parameter mode trace write mode 0 updates the display f...

  • Page 1442

    Chapter ４ native device message details 4-360 xma/xma? Write and query trace data (trace a) function this command writes and queries the trace data of trace a in ascii format. Command xma wpoint,data query xma? Start,number response data1,data2,... Parameter wpoint specify the writing position as th...

  • Page 1443

    Chapter ４ native device message details 4-361 4 n ati ve d ev ice m es sa ge d et ail s example of use to set –20 dbm at the 1st point and –21 dbm at the 2 nd point. Xma 1,-20000 xma 2,-21000 xma? 1,2 > -20000,-21000 xmb/xmb? Write and query trace data (trace b) function this command writes and quer...

  • Page 1444

    Chapter ４ native device message details 4-362 details this function writes and queries positive detection trace data when the detection mode is positive & negative (normal mode). This command is not available in the following cases: • during the spectrum emission mask measurement. • during the spect...

  • Page 1445

    Chapter ４ native device message details 4-363 4 n ati ve d ev ice m es sa ge d et ail s start specify the loading start position as the number of displayed points from the left edge of the screen. Range 0 to 10, 20, 40, 50, 100, 200, 250, 400, 500,1000, 2000, 5000, 10000, 30000 (ms269xa only) number...

  • Page 1446

    Chapter ４ native device message details 4-364 xmd/xmd? Write and query trace data (trace d) function this command writes and queries the trace data of trace d in ascii format. Command xmd wpoint,data query xmd? Start,number response data1,data2,... Parameter wpoint specify the writing position as th...

  • Page 1447

    Chapter ４ native device message details 4-365 4 n ati ve d ev ice m es sa ge d et ail s example of use to set −20 dbm at the first point and set −21 dbm at the second point. Xmd 1,-20000 xmd 2,-21000 xmd? 1,2 > -20000,-21000 xme/xme? Write and query trace data (trace e) function this command writes ...

  • Page 1448

    Chapter ４ native device message details 4-366 details this function writes and queries positive detection trace data when the detection mode is positive & negative (normal mode). This command is not available in the following cases: • during the spurious emission measurement. • during the spectrum e...

  • Page 1449

    Chapter ４ native device message details 4-367 4 n ati ve d ev ice m es sa ge d et ail s xmf/xmf? Write and query trace data (trace f) function this command writes and queries the trace data of trace f in ascii format. Command xmf wpoint,data query xmf? Start,number response data1,data2,... Parameter...

  • Page 1450

    Chapter ４ native device message details 4-368 example of use to set −20 dbm at the 1st point and −21 dbm at the 2nd point. Xmf 1,-20000 xmf 2,-21000 xmf? 1,2 > -20000,-21000 xmz/xmz? Write and query trace data (gate view) function this command writes and queries the trace data of gate view in ascii ...

  • Page 1451

    Chapter ４ native device message details 4-369 4 n ati ve d ev ice m es sa ge d et ail s details this function writes and queries positive detection trace data when the detection mode is positive & negative (normal mode). This command is not available when gate view is set to off. Example of use to s...

  • Page 1452

    Chapter ４ native device message details 4-370..