C. Crane CCWiFi Instruction Manual - Media Player Functions
CC WIFI
17
Media Player Functions
CC WiFi
Page 23
SONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.
2. Turn the main dial clockwise until “Media Player” shows in
brackets — press the dial to select.
3. Turn the dial clockwise until “Playback Mode” shows — press the
dial to select.
4. Turn the dial clockwise until “Repeat” shows — press the dial to
select.
Configure Menu Options
To access the “Configure” menu follow these steps:
1. Briefly press the dial once to access the Primary Menu. You can
also access the Primary Menu by pressing and holding the BACK
button.
The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.
2. Turn the main dial until “Configure” shows in brackets — press the
dial to select. Turn the dial clockwise to access all the options.
This option is used for configuring your radioʼs network settings, net-
work parameters, and scanning for wireless networks. Once the radio
has established a connection to the network, the information will be
saved to the radio for later use.
Displays the electronic serial number and other information pertaining
to software and hardware installed on your internet radio.
Use this option to download new control programing for the radio. If
there is new firmware available when this option is selected, then the
radio will prompt you to download.
Note:
A firmware upgrade may take several minutes. DO NOT TURN
OFF THE POWER TO YOUR RADIO WHEN UPGRADING FIRM-
Media Player Functions
CC WiFi
Page 23
SONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.
2. Turn the main dial clockwise until “Media Player” shows in
brackets — press the dial to select.
3. Turn the dial clockwise until “Playback Mode” shows — press the
dial to select.
4. Turn the dial clockwise until “Repeat” shows — press the dial to
select.
Configure Menu Options
To access the “Configure” menu follow these steps:
1. Briefly press the dial once to access the Primary Menu. You can
also access the Primary Menu by pressing and holding the BACK
button.
The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.
2. Turn the main dial until “Configure” shows in brackets — press the
dial to select. Turn the dial clockwise to access all the options.
This option is used for configuring your radioʼs network settings, net-
work parameters, and scanning for wireless networks. Once the radio
has established a connection to the network, the information will be
saved to the radio for later use.
Displays the electronic serial number and other information pertaining
to software and hardware installed on your internet radio.
Use this option to download new control programing for the radio. If
there is new firmware available when this option is selected, then the
radio will prompt you to download.
Note:
A firmware upgrade may take several minutes. DO NOT TURN
OFF THE POWER TO YOUR RADIO WHEN UPGRADING FIRM-
Configure Menu Options
Page 24
CC WiFi
Allows you to change the display language.
WARE.
If the firmware upgrade is interrupted, your radio may endure
permanent damage. A firmware upgrade may take several minutes to
finish.
This option puts all settings back to their default, as they were when
the radio left the factory. If you perform a factory reset on your radio,
you will lose all your presets, clock settings, and wireless network
connection settings.
This option will display a key that can be used to register the radio on
the Reciva Customer Portal.
Selecting this option will alter the Internet radioʼs backlight values.
1. After selecting the “Backlight” menu item, the radio will show three
backlight adjustment modes: “Inactive”, “Active”, and “Standby”.
These three settings are explained below:
a) The “active” state is when the user is pressing buttons or
turning knobs.
b) The radio goes into its “inactive” state when there is no
user activity for 30 seconds.
c) “Standby” is the state when the radio has been turned off.
2. Rotate the dial to select the desired backlight mode — press the
dial to select.
3. The radio will display the current backlight value for the selected
mode. You can change this value by turning the dial to increase or
decrease it.
Use this option to set the time, date and clock format. See “Setting
the Time and Date” on page 15.
Use this option to set a name for your radio that can be recognized by