Eclipse EC-P50 Installation Manual - page 5
P0016-LI-03.01
5
Control Panel
The EC-P50 control panel is an advanced intruder alarm system
with 10 on-board zones and on-board multi format communicator.
The system can be expanded to 50 zones using the 10 zone
expansion modules (EC-EX10 or EC-EX10/I). The EC-EX10/O can
be used where additional programmable outputs are required.
The system supports 5 partitions and 50 user codes and is ideal
for multi-area and multi-tenant applications within domestic and
commercial installations.
The control panel provides a multi-channel integrated speech
dialler and voice annunciation feature. Voice messages are
recorded via a touch tone telephone or by using the Eclipse UDL
software package.
Remote arming and disarming and system control can also be
carried out by calling the protected premises with a touch-tone
telephone. On answering the incoming call you are greeted with a
voice prompted menu.
The system can be further enhanced by using the EC-COM/IP
module which provides both IP and X-10 connectivity. X-10 is a
simple home automation protocol that uses the existing mains
wiring to communicate with X-10 compatible devices via a XM10U
controller. Once the EC-COM/IP is installed, both the system and
X-10 devices can be controlled remotely using smart phone apps.
A choice of either LCD or LED remote keypads is available. Other
features include:
f
10 programmable on-board zones
f
5 programmable outputs (1Amp rated)
f
On-board communicator/modem/speech dialler
f
Local or remote upload/download
f
1000 event log
f
Advanced system diagnostics
f
1.5 Amp switched mode power supply
f
Two communication ports for accessories etc
f
Loudspeaker output
f
Selectable battery charging rate
f
Real time clock
f
Two-wire smoke detector support
f
Flash upgradable
Remote Keypads
The EC-P50 will accept up to a maximum of 6 remote keypads. All
remote keypads require a 4-wire connection to the control panel
using standard alarm cable. The following models are available:
EC-LED Remote Keypad
The LED keypad features a dual 7 segment display for displaying
zone status and system fault messages. A set of dedicated
system status LEDs for AC, Ready, Armed, Trouble, Bypass, Alert
and Alarm are also provided. Other features include:
f
Internal sounder
f
Backlit keyboard
EC-LCD Remote Keypad
The LCD keypad features a 2 x 20 character blue display for
showing all zone status and system fault messages. A set of
dedicated system status LEDs for AC, Trouble and Alert are also
provided. Other features include:
f
Internal sounder
f
Backlit keyboard
Expansion Modules
The following expansion modules are available:
EC-EX10 Zone & Output Expander
The EC-EX10 is a housed zone and output expansion module that
is connected to the 4-wire control panel network. Features
include:
f
10 fully programmable zone inputs
f
10 programmable outputs (8 x 100mA; 2 x 1Amp)
f
Internal piezo sounder
f
16
Ω
loudspeaker connection, with programmable volume
f
Tamper protection
f
Engineer keypad port
f
Stylish housing
EC-EX10/I Zone Expander
The EC-EX10/I is a housed zone expansion module that is
connected to the 4-wire control panel network. Features include:
f
10 fully programmable zone inputs
f
Tamper protection
f
Stylish housing
EC-EX10/O Output Expander
The EC-EX10/O is a housed output expansion module that is
connected to the 4-wire control panel network. Features include:
f
10 programmable outputs (8 x 100mA; 2 x 1Amp)
f
Tamper protection
f
Stylish housing
EC-COM/IP Communication Module
The EC-COM/IP is an IP based communicator and X-10 home
automation interface PCB module. Features include:
f
Ethernet connection to LAN/WAN
f
Remote access via Eclipse UDL or smart phone app
f
Alarm reporting via LAN/WAN to PC based alarm receiver
f
X-10 port for automating X-10 devices via the XM10U/E
f
X-10 devices controlled via the system or smart phone app
f
PCB module clips into EC-P50 control panel housing
EC-USB-Link
The EC-USB-Link provides USB connectivity between the EC-P50
and the host computer. It is required when a direct connection is
required between the Eclipse UDL software package and the EC-
P50.
Upload/Download Software
Eclipse UDL is a Windows® based software package that can be
used to remotely or locally program and diagnose the Eclipse
range of security systems. Features include:
f
Simple intuitive user interface
f
Local or remote via modem and IP
f
System remote control
f
Advanced system diagnostics