Fadini Junior 633 Instruction Manual - page 14
pag 21
Automatic / Semiautomatic:
4
3
COMUNE
COMUNE
APRE
NA
External clock
Opening by way of an external clock:
Connection: connect the NO contact of the Clock with terminal 4 OPEN and
terminal 3 COMMON in parallel, enabling the automatic closing with the Dipswitch
3=ON
Operation: program the opening time on the clock, at the time set the gate
will open and remain open (the flasher goes off) and it will not accept other
commands (not even radio) until the time that has been set on the clock runs
out. Once that time has expired, after the pause time, the automatic closing
will follow.
Automatic cycle: upon open command impulse, the gate opens, stops in
pause for the time set in the Pause Trimmer, which, once passed will reclose
automatically
Semiautomatic Cycle: with an open command impulse the gate moves to
opening. To close the passage it is necessary to give the close command
Dip - Switch and LED signalling of the different functions
-
+
Pause Trimmer: the pause time in the
automatic mode is adjusted to 120s
3
ON: Close in automatic
OFF: Semiautomatic
DIP-SWITCH 3:
Slowdowns:
During programming it is recommended that the positions of initiate slow down
in opening and in closing be set. Afterwards, these may be removed or
recovered by way of the 6 Dipswitch.
The speed of the final run slowdown of the gate is calibrated at the factory,
while the torque is proportional to the force exerted by the Junior operator by
way of the Force Trimmer
Trimmer Force: adjust the torque applied
on the gate
6
ON: Eliminates slowdowns
OFF: Activates slowdowns programm
DIP-SWITCH 6:
Desction
Force Trimmer: adjusts the torque applied
on the gate.
Beyond 3/4 of the adjustment it is possible
to obtain a greater force, which does
not enable the gate to detect an
obstacle.
7 OFF: Attiva la rilevazione degli ostacoli
ON: Nessuna rilevazione all'urto dell'ostacolo
DIP-SWITCH 7:
Closing after passage by the pair of photocells:
This Function enables the automatic closing the passage through the pair of
photocells after 3 seconds.
9
ON: Enables the automatic closing after the
passage through the pairs of photocells
OFF: No automatic closing
DIP-SWITCH 9:
Check photocells before start up:
This Function enables the check of the safety devices such as the photocells
before starting up the movement of the gate.
10
ON: Enables the check of the safety devices
OFF: Deactivates the check of the safety devices
DIP-SWITCH 10:
3
ON: Closes in automatic
ATTENTION: each variation or action on the Dipswitches for the functions, at any time, will be executed at the moment
of the next opening or closing command!
!
Reverse direction upon contact with an obstacle:
This Function enables the inversion of the movement upon contact with an
obstacle.
If this function is active, upon contact with an obstacle the cover casing LED
turns AMBER for a complete cycle of opening and closing after the detection
of the obstacle.
- Opening phase: the function reverses the direction for 10 cm freeing the
obstacle
- Closing phase: the function reverses the direction up to the limit switch
The sensitivity of the function is proportional to the force exerted by the Junior
by way of the Force Trimmer
PLEASE NOTE. If the gate detects an obstacle 5 consecutive times during a
complete open - stop - close cycle, the gate will remain open and the lamp
will flash with a Blue light
-
+
-
+
ADJUSTMENT OF STRENGTH:
The adjustment of the Force by the Trimmer must be necessary to move the gate. This adjustment also determines the
strength and impact resistance slowing down with an obstacle. A force too high inertia of the gate leads to incorrect
installation according to safety standards EN 12445 and EN 12453
Therefore, it requires the installer once adjusted the force applied to the gate operator to check the forces in play as
determined by the regulations EN12445 and EN12453 documented in the manual "Safety Standards" that the manufacturer
provides
!
meccanica
FADINI
Elpro 63
Junior 633 - Junior 650
GB
FUNCTIONS: DESCRIPTION OF THE FUNCTIONS OF THE JUNIOR 624 SLIDING OPERATOR