Fadini Junior 633 Instruction Manual - page 17
Via Mantova 177/A - 37053 Cerea (VR) Italy
Tel. 0442 330422 - Fax 0442 331054
e-mail: info@fadini.net - www.fadini.net
Installer's stamp
The manufacturing firm reserves the right to modify this manualwithout notice; in addition
it
it assumes no responsibility for possible errors or damages to things or persons
The development of the MECCANICA FADINI Company has always been based upon the guarantee of the quality of its products and on
the existence of a system TOTAL QUALITY CONTROL, which has guaranteed the maintenance of quality levels over time and a constant
updating of the European Regulations, in the framework of a continuous process of improvement
meccanica
FADINI
meccanica
FADINI
GB
For optimum performance of the system over time according to safety regulations, it is necessary to perform proper maintenance and monitoring
of the entire installation for the automation, the electronic equipment installed and for the cabling connected to these. The entire installation must
be carried out by qualified technical personnel, filling out the Maintenance Manual indicated in the specific Regulation Book to be requested:
- Electromechanical automation: maintenance inspection check at least every 6 months;
- Electronic equipment and safety systems: inspection check at least once every month;
-Ordinary and extraordinary maintenance must be agreed to between the principal and the maintenance firm.
- Dispose of the packaging containers, such as the cardboard, plastic sheeting, foam padding, etc., through specialised waste disposal firms.
- DO NOT DISPOSE OF TOXIC SUBSTANCES FOR THE ENVIRONMENT IN DOMESTIC WASTE DISPOSAL .
- In the event of the removal of the actuator, do not cut the electrical wires, but remove them from the terminal by loosening the set screws.
pag 24
Junior 633 - Junior 650
TECHNICAL SPECIFICATIONS AND DIMENSION
316
293
140
102
62,5
40
170
38
210
290
160
95
40
170
210
296
55
316
Technical specification
JUNIOR 633
JUNIOR 650
Power yield
0,25KW (0,33CV) 0,37KW (0,50CV)
Electrical power supply voltag 230V - 50Hz
230V - 50Hz
Power absorbed
400W
510W
Current absorbed
2A
2,4A
Maximum thrust force
600N
1000N
Motor revolution
1'350 rpm
1'350 rpm
Speed
10m/1'
10m/1'
Ratio
1:31
1:31
Protection Grade
IP54
IP54
Lubrication
Operational Temperature
-20°C +50°C
-20°C +50°C
Weight
11,3Kg
13,5Kg
Service cycle: 60s open/close - 30s pause
Complete cycle time: 180s = 20 cycle/hour
The Meccanica Fadini Company declares under its own responsibility that the models Junior 633 and Junior 650 are electromechanical gate openers
conceived for being sold and installed in "automated systems" with original accessories and components indicated by the Manufacturing Firm.
The installer must leave a personal Declaration of Conformity and to perform all necessary tests so as to make the system compliant with the regulations.
The manufacturing firm assumes no responsibility for the improper use of the product.
The product has been deemed compliant with the following specific regulations
:
- Analysis of Risks and successive procedures for eliminating them:
EN 12445 e EN 12453
- Low Voltage directive
2006/95 CE
- Electromagnetic Compatibility Directive
2004/108/CEE e 92/31 CEE
- Directive R&TTE
99/5/CE
Organism and laboratory notify DM 2004/108/CE:
Institute of Researches and Collaudi M.Masini srl - moscova street,11 20017 Rho (MI)
Notify CE 0068 - Accreditato SINCERT 047A - Accreditato SINAL 0019
Conformity follow regulations: UNI EN 1324-1, UNI EN 12604, UNI EN 12605, UNI EN 12445, UNI EN 12453
Declaration of Conformity of the Manufacturer
Via Mantova 177/A - 37053 Cerea (VR) Italy
Tel. 0442 330422 Fax 0442 331054
info@fadini.net - www.fadini.net
meccanica
FADINI
The responsable
Date:
03-03-10
ORDINARY MAINTENANCE AND DISPOSAL
Directive 2003/108/CE
Disposal of electrical and
electronic goods
Disposal of substances hazardous
for the environment is prohibited
GB