Fadini Junior 633 Instruction Manual - page 16
pag 23
POSSIBLE MALFUNCTIONS
The LED device on the protective casing enables the installer and the end user to see if the system is actually working
properly (Blue light) or if there is some fault that does not permit proper operation (amber light).
OPENING OF THE UNLOCKING HANDLE FOR THE MANUAL OPERATION OF THE GATE
Using the unlocking handle lever with the coded key, the electrical power supply
is always disconnected from the system.
For the unlocking and later manual movement of the gate, it is necessary that
the handle be opened until it stops beyond 90°.
Upon closing and later locking of the lock, the electrical power supply is
reconnected to the mains at the PCB.
IMPORTANT: Once the electrical power supply has been disconnected using
the unlocking key, upon reconnection of the mains electrical power, the first
movement of the Junior is always toward closing at a normal operational
speed with no programmed slowdowns. To recover all of its functions (such
as slowdowns) it is necessary that a full cycle be completed all the way to
the opening limit switch.
FA
D
IN
I
meccanica
FADINI
Elpro 63
GB
1)
2)
3)
Fault
Causes
Procedur
es
Led lamp off
- Check lthe line and all fuses
- Close and remove the key from
the lock
+90°
Led lamp remains
Amber
- Detects the continuous presence of an obstacle or
of possible friction during movements
- Remove the present obstacle
- Remove eventual causes of friction
on the sliding gate guides
-Operational force too low for the inertia of the gate
- Increase the Trimmer Force
- Contact on photocell
- Clean the covers of photocells
- Photocells not aligned
- Batteries dead (Orbita 57)
- Pair of photocells too far apart
The gate starts to move
but then stops or
reverses direction
- - Operational force too low for the inertia of the gate
- Detects the continuous presence of an obstacle or of
possible friction during movements
- Increase the force on Trimmer
- Remove eventual causes of friction
on the sliding gate guides
Junior 633 - Junior 650
The Meccanica Fadini Company declares under its own responsibility that the models Junior 633 and Junior 650 are electromechanical gate openers
conceived for being sold and installed in "automated systems" with original accessories and components indicated by the Manufacturing Firm.
The installer must leave a personal Declaration of Conformity and to perform all necessary tests so as to make the system compliant with the regulations.
The manufacturing firm assumes no responsibility for the improper use of the product.
The product has been deemed compliant with the following specific regulations
:
- Risk Analysis and later elimination procedures:
EN 12445 e EN 12453
- Directive machine
2006/42/CE
- Low Voltage Directive
2006/95 CE
- Electromagnetic Compatibility Directive
2004/108/CEE e 92/31 CEE
- R&TTE Directive
99/5/CE
Organism and laboratoriy notify DM 2004/108/CE:
Institure of Research and Collaudi M.Masini srl - moscova street,11 20017 Rho (MI)
Notify CE 0068 - Creditated SINCERT 047A - Creditated SINAL 0019
Conformity follow the norms: UNI EN 1324-1, UNI EN 12604, UNI EN 12605, UNI EN 12445, UNI EN 12453
Declaration of conformity of the manufacture
Via Mantova 177/A - 37053 Cerea (VR) Italy
Tel. 0442 330422 Fax 0442 331054
info@fadini.net - www.fadini.net
meccanica
FADINI
Responsable
Date:
03-03-10
The gate does not move - one or more contac NC are open
- fuses burnt
- Check all NC contacts
- Check fuses state
- lack of mains electrical power supply 230V
- 5A line fuse burned
- 6,3A 24 V line fuse burned
- Unlocking handle lock not locked