Fender MUSTANG FLOOR Advanced Owner's Manual - page 6
M U S T A N G
™
F L O O R
• Bypass Effect — (On/Off)Select"On"tobypasstheeffectcurrent-
lyselectedintheExpressionBehaviormenuwhenswitchingthe
pedaltoVolumemodeorselect"Off"toleavetheeffectactive.
• Reset Parameter to Preset Value when Switching to Volume
Mode — (On/Off) Select "On" to return the Expression Mode
ParametertothestoredpresetvaluewhenswitchingtoVolume
mode. Select "Off" if you want the parameter be left set to the
positionofthepedalwhenswitchingtoVolumemode.
Pedal Calibration
Occasionally it may become necessary to calibrate the Mustang
Floor's expression pedal and/or an EXP-1 expression pedal con-
nectedtotheMustangFloor,toresettheparameterrangeofthe
pedal(s)toensureconsistentperformance.
To calibrate the expression pedal and EXP-1 pedal:
1.
(Optional)PluganEXP-1pedalintothe"EXP-1/MS-4"jackon
thebackoftheMustangFloorusingtheincludedcable.
2.
TurntheMustangFlooroff.
3.
Press and hold the UTIL button on the Mustang Floor while
turningtheMustangFloorbackon.ContinueholdingtheUTIL
buttondownuntilitisnolongerilluminated.
4.
Rock the Mustang Floor expression pedal (and the EXP-1, if
connected), through the full range of motion between heel
andtoepositions.
5.
The Mustang Floor expression pedal and the EXP-1, if con-
nected,havebeencalibrated!
Pedal Tension
Occasionallyitmaybecomenecessarytoadjustthetensionofthe
axlenutontheexpressionpedaltoincreaseordecreasetheease
ofpedalmovement.
To adjust pedal tension:
Pryoffthecircular"F"capfromtherightsideofthepedalwitha
smallflatbladescrewdriver,thenusea10mmsocketwrenchto
adjusttheaxletension.Donotover-tightentheaxlenuttoavoid
damagingthepedalassembly.
10 mm
EXP-1 & MS-4
USB
EXP-1/
MS-4
GROUND
LIFT
PHONES
AUX IN
XLR OUT
LEVEL
UNBALANCED OUT
MIDI
R
L
R
L
OUT
IN
INSERT LOOP
INPUT
POWER
SEND
RETURN
I
0
YourMustang™Floorgivesyoutheoptionofaddingan
external EXP-1 expression pedal and an MS-4 four-
button footswitch for additional flexibility. Both the
EXP-1andMS-4canbeconnectedtogetherthroughthe
EXP-1/MS-4jackonthebackoftheMustangFloor.
To use the EXP-1 and MS-4 simultaneously, plug the EXP-1 into
the Mustang Floor and then plug the MS-4 into the second jack
on the EXP-1.
EXP-1 Expression Pedal (P/N 2301050000)
Configure the EXP-1 expression pedal through the pedal menus
(seePedalMenus,page5).TheEXP-1onlyfunctionsinExpression
modewhenconnectedtotheMustangFloor.ThegreenLEDindi-
cateswhentheEXP-1pedalispoweredonandtheredLEDindi-
cateswhetherExpressionmodeiscurrentlyenabled.
MS-4 Four-Button Footswitch (P/N 0080996000)
TheMS-4footswitchdisplayandLEDsshowyoumuchofthesame
informationastheMustangFloorscreen,soyoucanforexample,
tune your guitar and select presets by watching the footswitch
without ever looking at the screen onboard the Mustang Floor!
TheMS-4allowsyouto:
•SelectQuickAccesspresets(QA1/QA2/QA3)
•Selectpresets(up/down/bank)
•Bypasseffects
•ActivatetheTuner
The footswitch has three modes that are identified by the three
LEDslabeledMODE1,MODE2andMODE3.Thefootswitchalso
hasaTunermodewhichisindicatedwhenallofthemodeLEDs
areoff.
To switch between modes, press the MODE button. To activate
Tunermode,pressandholdtheMODEbutton.
• Mode 1—SelectoneofthreeQuickAccesspresetsusingthebut-
tonslabeled:QA1/QA2/QA3(inlinewiththeMODE1LED).The
numberofthepresetwillappearinthedisplayofthefootswitch.
You can assign any preset to be a Quick Access preset in the
utility menus. (see Utility Menus, page 7).
• Mode 2—Select presets down/up, or in banks of 10, using the
buttons labeled: DOWN / UP / BANK (in line with the MODE 2
LED).Thenumberofthepresetwillappearinthedisplayofthe
footswitch.
6