I-Sotec i-soamp Manual manual - page 14
D Operation and Connection of the Auxgate Connect
D.1 Connection
The connection of the Auxgate Connect to power supply and speakers
is to be done as described in chapter A1 (the only option for speaker connection
is “Normal”). The use with a subwoofer is not intended.
All AUX sources are connected directly to the housing. The input AUX 1 is inten-
ded for use with MP3 players, DVD players or similar sources while the input
NAV/TEL with automatic muting system is to be used for navigation systems or
handsfree phone systems.
D.2 Operating Elements and Connections
1: Connection “AUX1”
2: Connection “Nav/Tel”
3: Volume Control “AUX1”
4: Volume Control “Nav/Tel”
5: Connection “Tel. Mute In / Mute Out”
6: System plug (power, loudspeaker in- and outputs)
7: Battery indicator (POWER)
8: Mode indicator (RADIO)
9: Mode indicator (NAV/TEL)
10: Volume Control “Level”
D.3 Operation
The radio volume
is controlled at the
radio. While the
radio volume is
turned up the AUX
1 input is muted.
To listen to AUX 1
the radio volume
needs to be turned
all the way down.
If there is a signal
at the input NAV/TEL the other sources will be muted automatically and the
signal is amplified. The Volume is controlled at each connected source with their
integrated Volume controls.
D.4 Settings
The main volume of the 3 function modes(Radio, AUX 1, NAV/TEL) is to be set
by the level-controls “Level”, “AUX 1” and “NAV/TEL” at the Auxgate Connect
housing. CAUTION: The “Level” control sets the main volume in radio mode only;
it has no influence on the main volume of the other modes.
These controls are usually set to 0 when leaving the Factory if not then please
correct the settings.
Settings for “Level”: Set the radio to full volume the turn the “Level” poti slowly
up to the desired maximum level. If the speakers distort turn the “Level” poti
D Bedienung und Anschluss Auxgate® Connect
D.1 Anschluss
Der Anschluss des Auxgate® Connect an das Autoradio, die
Stromversorgung und die Lautsprecher erfolgt wie beim Medialink im Modus
„Normal“ (Siehe Kapitel A1.1 bis A1.3). Der Betrieb mit Subwoofer ist nicht
vorgesehen.
Sämtliche AUX-Quellen werden direkt am Gerät angeschlossen. Der Eingang
„AUX1“ (Bild: 1) ist für MP3-, DVD-Player und ähnliche Quellen vorgesehen,
der Eingang „Nav/Tel“ (Bild: 2) mit automatischer Signalverwaltung für
Navigationssysteme oder Mobiltelefone mit Freisprechanlage.
D.2 Bedienelemente und Anschlüsse
1: Anschluss “AUX1”
2: Anschluss “Nav/Tel”
3: Drehregler “AUX1”
4: Drehregler “Nav/Tel”
5: Anschluss “Tel. Mute IN / Mute Out”
6: Systemstecker (Strom, Lautsprecher-Ein- und Ausgänge)
7: Betriebsanzeige (POWER)
8: Modus-Anzeige (RADIO)
9: Modus-Anzeige (NAV/TEL)
10: Drehregler “Level”
D.3 Betriebsmodi
Die Radio-
Lautstärke wird mit
dem Lautstärke-
regler am Radio
geregelt. So lange
ein Signal vom
Radio anliegt, sind
die Signale vom
Eingang AUX1 gar
nicht und Signale
vom Eingang
„Nav/Tel“ nur nach
(automatischer)
Aktivierung zu
hören.
Wird die Radio-Lautstärke vollständig heruntergedreht, wird das Signal vom
Eingang „AUX1“ wiedergegeben.
Liegt am Eingang „Nav/Tel“ oder „Tel.Mute“ ein Signal an, werden die ande-
ren Quellen automatisch gemutet und das Signal von diesem Eingang wieder-
gegeben.
Die Lautstärke der AUX-Quellen wird direkt an den daran angeschlossenen
Geräten geregelt.
D.4 Auxgate® Einstellungen
Die Grundlautstärke der drei Betriebsmodi (Radio, AUX1, Nav/Tel) wird über
die Poti-Drehregler „Level“, „AUX1“ und „Nav/Tel“ an der Geräterückseite ein-
gestellt. ACHTUNG: Der Drehregler “Level” regelt lediglich die Grundlautstärke
D
UK
manual_isoampML_AGConnect 30.01.2007 17:07 Uhr Seite 14