I-Sotec i-soamp Manual manual - page 5
A.1.2 Overview – The i-soamp connection principle
This depiction is designed to give you an overview of how the i-
soamp is connected to your vehicle's components in principle. The follo-
wing steps are required to connect the i-soamp to your existing car radio:
1. Connect the i-soamp cable harness to the compact plug on the i-soamp.
2. Connect the power plug on the i-soamp cable harness to the power recepta-
cle of the supplied power adaptor.
3. Remove the ISO loudspeaker receptacle of the vehicle's cable harness from the
car radio and connect it to the
ISO loudspeaker coupling (brown)
of the i-soamp cable harness. (For
details on connection variants see
Chapter A.1.3, A.1.4 and A.1.5)
4. Remove the vehicle cable har-
ness ISO power coupling from the
car radio and connect it to the
ISO power coupling (black) of the
supplied power adaptor (For
details on the power connection
see Chapter A.1.6 and A.1.7)
5. Connect the ISO power plug
(black) of the supplied power
adaptor to the ISO power recep-
tacle of the car radio.
6. Connect the ISO loudspeaker
plug (brown) of the i-soamp cable
harness to the ISO loudspeaker
receptacle of the car radio.
In any case, be sure to read the
following chapter before you start
connecting the i-soamp to find
out about the details of the indivi-
dual connection options.
Alternative connection via RCA plugs (i-soamp Medialink only)
If you own a Radio with preamp outputs (RCA sockets) you can also connect the
radio via RCA plugs to the i-soamp. For details, please see chapter A1.5.
A.1.2 Überblick: Anschlussprinzip
Diese Darstellung soll Ihnen einen Überblick verschaffen, wie der
Medialink und das Auxgate® Connect grundsätzlich mit den
Komponenten in Ihrem Fahrzeug verbunden werden. Folgende Schritte sind
notwendig, um den Medialink oder das Auxgate® an Ihrem vorhandenen
Autoradio anzuschließen:
1. i-soamp-Kabelbaum mit dem Kompaktstecker am i-soamp oder Auxgate®
anschließen.
2. Stromstecker am i-soamp-Kabelbaum
mit der Kupplung des mitgelieferten
Stromadapters verbinden.
3. ISO-Lautsprecherkupplung des
Fahrzeug-Kabelbaums vom Radio lösen
und an der ISO-Lautsprecherkupplung
(braun) des i-soamp Kabelbaums verbin-
den. (Details zu Anschlussvarianten siehe
Kapitel A.1.3, A.1.4, A.1.5)
4. Die ISO-Stromkupplung des Fahrzeug-
Kabelbaums vom Autoradio lösen und
mit der ISO-Stromkupplung (schwarz)
des mitgelieferten Stromadapters verbin-
den (Details zum Stromanschluss siehe
Kapitel A.1.6 und A.1.7)
5. Den ISO-Stromstecker (schwarz) des
mitgelieferten Stromadapters mit der
ISO-Stromkupplung des Autoradios ver-
binden.
6. Den ISO-Lautsprecherstecker (braun)
des i-soamp-Kabelbaums mit der ISO-
Lautsprecherkupplung des Autoradios
verbinden.
Lesen Sie auf jeden Fall die folgenden
Kapitel, bevor Sie mit dem Anschließen
beginnen, um die Details der einzelnen
Anschlussvarianten zu erfahren.
Alternativer Anschluss über Cinch-Kabel (nur i-soamp Medialink)
Ein Autoradio, das über einen Vorverstärker-Ausgang verfügt (Cinch-Anschlüsse),
können Sie auch über Cinch-Kabel (nicht mitgeliefert) mit dem Medialink verbin-
den. Details dazu entnehmen Sie bitte Kapitel A1.5.
D
UK
manual_isoampML_AGConnect 30.01.2007 17:07 Uhr Seite 5