I-Sotec i-soamp Manual manual - page 6
A.1.4 Front + Subwoofer (Medialink only)
With this connection, the front speakers and the optional subwoofer are
driven by the i-soamp. The back speakers can be connected directly to the
radio by by switching the 4-
pinned plugs (see picture). Do
only use i-sotec subwoofers!
Other speakers can damage
the i-soamp.
The selector switch is turned
to “Front + Sub” position.
This means that the active fil-
ters required for subwoofer
operation ara automatically
activated.
The volume basic setting for
the front speakers is done
with the front level control.
The subwoofer level is adju-
sted via the rear level control.
1.3 "Normal" loudspeaker
connection option
(Medialink and Auxgate®)
The i-soamp Medialink or
Auxgate® Connect is connected to the
front and back speakers. The selector
switch (i-soamp only) is set at the "normal"
position. This means that all loudspeakers
are operated
without affecting the frequency response.
After the i-soamp cable harness has been
connected to the compact plug on the
Medialink or Auxgate®, the loudspeakers
are connected as follows:
1. Remove the vehicle cable harness ISO
loudspeaker plug from the car radio and
connect it to the ISO loudspeaker recepta-
cle (brown) of the i-soamp cable harness.
2. The two 4-pole plugs stay connected (as
it is when delivered)
3. Connect the ISO loudspeaker plug of the i-soamp cable harness with the
car radio ISO loudspeaker receptacle.
4.The power connection is performed in accordance with
Chapter A.1.6 and/or A.1.7
A1.4 Anschlussvariante „Front und Subwoofer“
(nur Medialink)
Bei dieser Variante werden die vorderen Lautsprecher
und der optionale Subwoofer mit dem i-soamp ange-
trieben. Die hinteren Lautsprecher können durch
Umstecken der vierpoligen Stecker (siehe Abbildung)
direkt mit dem Radio verbunden werden. Verwenden
Sie ausschließlich Original Subwoofer von i-sotec!
Andere Lautsprecher können den i-soamp beschädi-
gen!
Der Wahlschalter wird bei dieser Anschlussvariante auf
die Position „Front+Sub“ gestellt. In dieser
Schalterposition werden die benötigten aktiven Filter
für den Basslautsprecher und die vorderen
Lautsprecher automatisch aktiviert. Die
Pegeleinstellung für die vorderen Lautsprecher erfolgt
über den Regler Level Front. Der Subwoofer wird über
den Regler Level Rear geregelt.
Nachdem der Kabelbaum des i-soamp mit dem
A1.3 Anschlussvariante „Normal”
(Medialink und Auxgate®)
Der Medialink oder das Auxgate® wird
mit den Front- und Rear-Lautsprechern ver-
bunden. Der Wahlschalter (nur i-soamp) wird hierzu
auf die Position „Normal“ gestellt. Das bedeutet,
dass alle 4 Lautsprecher „Fullrange“, also ohne
Beeinflussung des Frequenzgangs, betrieben wer-
den.
Nachdem man den Kabelbaum des Medialink oder
Auxgate® mit dem Kompaktstecker am i-soamp
angeschlossen hat, werden die Lautsprecher folgen-
dermaßen angeschlossen:
1. Den ISO-Lautsprecherstecker des
Fahrzeugkabelbaums vom Autoradio trennen und
mit der ISO-Lautsprecherkupplung (braun) des
i-soamp-Kabelbaums verbinden.
2. Die 4-poligen Stecker bleiben paarweise miteinan-
der verbunden (wie im Auslieferungszustand)
3. ISO-Lautsprecherkupplung des i-soamp-Kabelbaums
mit ISO-Lautsprecherkupplung des Radios verbinden.
4. Der Stromanschluss erfolgt gemäß
Kapitel A.1.6 bzw. A.1.7
D
UK
manual_isoampML_AGConnect 30.01.2007 17:07 Uhr Seite 6