I-Sotec i-soamp Manual manual - page 7
Kompaktstecker am i-soamp angeschlossen ist, werden die
Lautsprecher folgendermaßen angeschlossen:
1. ISO-Lautsprecherstecker des Fahrzeugkabelbaums (vom Radio
trennen) mit ISO-Lautsprecherkupplung (braun) des i-soamp-
Kabelbaums verbinden.
2. Die Verbindungen der 4-poligen Stecker lösen und dann, wie auf der
Abbildung zu sehen, miteinander verbinden. Es werden dabei die beiden 4-
poligen Stecker, die sich an der ISO-Lautsprecherkupplung und an dem ISO-
Lautsprecherstecker befinden, miteinander verbunden.
3. Den Subwoofer mit dem zugehörigen Anschlusskabel am passenden
Stecker des i-soamp-Kabelbaums anschließen.
4. Die ISO-Lautsprecherkupplung des i-soamp-Kabelbaums mit der ISO-
Lautsprecherkupplung des Autoradios verbinden.
5. Stromanschluss: Siehe Kapitel A.1.6 bzw. A.1.7.
After the i-soamp cable harness has been connected to to the
compact plug on the i-soamp, the loudspeakers are connected as
follows:
1. Remove the vehicle cable harness ISO loudspeaker plug from the
car radio and connect it to the ISO loudspeaker recaptacle (brown) of the i-
soamp’s cable harness.
2. Disconnect the 4-pinned plugs and connect them as seen in the picture.
This way the 4-pinned plugs on the ISO Loudspeaker socket and on the ISO
loudspeaker plugs are connected.
3. Connect the i-sotec subwoofer with it’s delivered cable to the fitting plug
on the i-soamp’s cable harneess.
4. Connect the ISO loudspeaker plugs of the i-soamp cable harness to the ISO
loudspeaker sockets of the car radio.
5. The power connection is made in accordance
with Chapter A.16 or A.1.7.
D
UK
A1.5 Alternativer Anschluss über Cinch-Kabel (nur i-soamp
Medialink)
Ein Autoradio, das über einen Vorverstärker-Ausgang verfügt (Cinch-Anschlüsse),
können Sie auch über Cinch-Kabel (nicht mitgeliefert) mit dem Medialink verbin-
den. Bitte beachten Sie, dass die Cinch-Eingänge parallel zu den so genannten
High-Level-Eingängen (Iso-Stecker für Lautsprecheranschluss) geschaltet sind und
daher nur einer dieser Eingänge verwendet werden darf.
Die Stromversorgung und der Lautsprecher-Ausgang des i-soamp werden auch
bei dieser Anschlussvariante über die ISO-Anschlüsse am i-soamp-Kabelbaum ver-
bunden (siehe Kapitel A1.2 Punkte 1 - 5). Die Signal-Übertragung vom Autoradio
zum i-soamp erfolgt, abweichend von Kapitel A1.2 Punkt 6, über Cinch-Kabel.
Außerdem muss der Remote-Eingang des Medialink über ein geeignetes Kabel
(nicht mitgeliefert) mit dem Remote-Ausgang des Autoradios verbunden werden.
Wenn Sie nicht sicher sind, welches die richtigen Ausgänge am Autoradio sind,
fragen Sie bitte Ihren Car-Audio-Fachhändler um Rat!
In der Anschlussvariante „normal“ (Betrieb der Front- und Rear-Lautsprecher über
den i-soamp, siehe auch Kapitel A1.3) werden die vier Cinch-Eingänge des i-
soamp (Front Left, Front Right, Rear Left, Rear Right) per Cinch-Kabel mit den ent-
sprechenden Ausgängen des Radios verbunden.
In der Anschlussvariante „Front und Subwoofer“ (Betrieb der Front-Lautsprecher
und eines optionalen i-sotec Subwoofers über den i-soamp, Kanäle 3 und 4 in
Brücke geschaltet, siehe auch Kapitel A1.4) werden NUR die Anschlüsse „Front
Left“ und „Front Right“ per Cinch-Kabel mit den entsprechenden Ausgängen des
Radios verbunden. Nur so ist die für den Subwooferbetrieb notwendige
Frequenzfilterung möglich!
A1.5 Alternative connection via RCA plugs (i-soamp Medialink
only)
If you own a Radio with preamp outputs (RCA sockets) you can also connect the
radio via RCA plugs to the i-soamp. Please note that the RCA input runs parallel
to the so called high level inputs (ISO plug for speaker connection) so only one
connection is to be made. To use the RCA input, you need an additional RCA
adapter cable, and also a cable for the Remote input (not supplied).
For this connection, power supply and speaker output of the i-soamp are con-
nected via the i-soamp cable harness as described in chapter A1.2, points 1-5.
The signal transfer from the radio to the i-soamp is, contrary to chapter A1.2
point 6, done via an RCA cable. Also the remote-input of the i-soamp must be
connected to the remote output of the radio with a fitting cable (not supplied).
If you are not sure about the correct outputs and cables, ask your qualified car
audio dealer for assistance!
For connection option „normal“ (amplification of front and rear loudspeakers via
the i-soamp, see also chapter A1.3) the four RCA inputs of the i-soamp (Font
and Rear Left/Right) are connected via an RCA cable to the corresponding out-
puts of the radio.
For connection option „front + sub“ (amplification of front- loudspeakers and an
optional i-sotec subwoofer via the i-soamp, see chapter A1.4) ONLY the RCA
inputs „Front Left“ und „Front Right“ of the i-soamp are connected via an RCA
cable to the corresponding outputs of the radio. Otherwise, the active filters
required for subwoofer operation are not activated.
manual_isoampML_AGConnect 30.01.2007 17:07 Uhr Seite 7