Mackie TT24 Quick Start Manual - Ch 3: Quickstart Tutorial
12
TT24 DIGITAL LIVE CONSOLE
TT24 DIGIT
AL LIVE C
ONS
OLE
Ch 3: Quickstart Tutorial
3.1 Connect Amplifier/
Speakers
1. Plug in a left-right pair of amps/speakers into the
MAINS OUT LEFT
and
RIGHT
XLR connectors
(Figure 3-1).
2. Connect an amp/speaker to
AUX SEND 1
.
3. Plug in headphones.
3.2 Connect a Mic
This section tells you how to connect a mic to
channel 1, set the gain, route to groups/auxes, and
engage/adjust the variable high-pass filter.
Connect mic to channel 1
1. Plug a mic into channel 1’s XLR input (top-right of
rear panel).
2. Press the
ANLG
bank select button (right of
Figure 3-2).
3. Set the
LINE
switch to the up (mic) position (left
of Figure 3-2).
4. Set the
48V
switch to the
down
position if the mic
uses phantom power; set it to the up position other-
wise.
Set the channel gain
5. Activate the
PFL
button (right of
Figure 3-2).
6. Activate channel 1’s
SOLO
button
(above fader) to set gain.
7. Provide a representative signal to the
mic, watch the meters to the right of
the Touchscreen, and listen in phones
(the phones level is in the UTILITY
area).
The level should be between –7 and
–10 dBFS.
8. Press
SOLO
again or
CLEAR SOLO
to
unsolo.
CD/TAPE A
TALKBACK
OUT
IN
CTR/MONO
RIGHT
LEFT
MONITOR
MAINS OUT
LINE INPUTS
AUX SENDS
1
2
3
4
5
6
7
8
9
10
11
12
L
R
C
12 Aux
Sends
CD/Tape B
Inputs
CD/Tape A
Inputs/Outputs
Main Outputs
R
M
L
1
2
3
4
5
6
7
8
R
L
Figure 3-1 Mains and Aux Sends Outputs
OL
SIG
1
-
+
GAIN
U
20
30
40
60
1
25
AUX
SEND
1
LINE
INPUT
SOLO
SELECT
MUTE
LINE
48V
V-Pot
knob
48 V
phantom
power button
Mic/Line
level button
Gain
knob
Overload
LED
Signal
LED
Select
button
Solo
button
Channel
fader
Mute
button
Bank/
Channel
description
RETURNS
MASTER
ANALOG
DIGITAL
GROUP ASSIGN/SELECT
MASTER
V-POT
CONTROL
AUX
SENDS
FX1
FX2
FX4
FX3
ANLG
MUTE
DGTL
1
RTNS
5
MSTR
SELECT
PFL
SOLO
MUTE
2
6
SELECT
SOLO
MUTE
3
7
SELECT
SOL
O
MUTE
4
8
SELECT
SOLO
CTR/
MONO
L/R
SELECT
PAN
HPF
AUX
MODE
2
4
6
8
10
12
CLEAR
SOLO
TRIM
METERS
AUX
PAN
1
3
5
7
9
11
Group Assign/Select buttons
Master Center/Mono Assign button
Master Left/Right Assign button
Master Select button
Group Select buttons
V-Pot Control
Aux Sends
Bank Select
Clear Solo and
PFL buttons
Group Faders
p
Group Mute buttons
Master Fader
Group Solo buttons
Aux Mode
AUX
AUX
Figure 3-2 Top of channel strip (left); Bank select, Clear Solo, PFL,
V-Pot control (right)
This Quickstart Tutorial will help you begin using
the TT24 quickly and easily by providing step-by-step
instructions for its most commonly utilized tasks. Rest
assured that our team of design engineers has verified
these instructions!
Before beginning the Quickstart Tutorial, please read:
• Chapter 1:
Introduction
to learn about the TT24’s
basic attributes, and terminology/conventions for
the console, Touchscreen, and user guide.
• Chapter 2:
TT24 Interface
provides a good overview
of the TT24’s important functional entities.
It may also be helpful to refer to Appendix A:
TT24
Configurations and Block Diagrams
to see how several
useful complete systems are interconnected.