NAIM AV2 Owner's Manual - page 7
6.1
switching on and off
Wake av2 from standby (power switch on).
Handset: press and hold standby.
Front panel: press and hold input or mode.
Put av2 to sleep (power switch on).
Handset: press and hold standby.
Front panel: press both input and mode.
6.2
input setup routine
Enter setup mode.
Handset: press menu followed by i/p
.
Front panel: press and hold input.
Scroll up or down parameter list.
Handset: press 2
or 8
Front panel: press input or mode.
Adjust setting
Handset: press
4 or 6
Front panel: rotate rotary control
three
setup parameters
parameter settings
6
6.0 av2 basics and quick setup
Installation of the av2 requires two setup routines to be carried out - input setup and
speaker setup. These routines configure the av2 for the source equipment and
loudspeakers it is to be used with and specify some signal decoding options. Some setup
parameters are dependent on the state in which the av2 was last shut down so setup may
be simplified if the av2 is returned to its setup defaults. See Section 11 for notes on
restoring setup defaults. Information on av2 decode modes and capabilities can be found
starting in Sections 10.2 - 10.6
The following diagrams provide a short-cut through the setup routines. They can also be
used in conjunction with the detailed notes in Sections 9 and 10 where setup choices
display legends are more fully explained.
Exit setup mode.
Handset: press menu followed by i/p
.
Front panel: press and hold input.
mode
2
8
8 c h . . . a n 1 . . . s c d
one
four
two
mode
input
mode
input
standby
standby
on
or
or
or
input
menu
i/p
or
input
menu
i/p
or
input
4
6
or
or
or
and
off
versatile analog input 1 (select source, multi)
V i 2
V i 1
- - - . . . a n 2 . . . s c d
versatile analog input 2 (select source, multi)
A N 3
- - - . . . a n 3 . . . s c d
analog input 3 (select source)
A N 4
- - - . . . a n 4 . . . s c d
analog input 4 (select source)
a n 5
- - - . . . a n 5 . . . s c d
analog input 5 (select source)
a n 6
- - - . . . a n 6 . . . s c d
- - - . . . o p 1 . . . s c d
- - - . . . o p 2 . . . s c d
analog input 6 (select source)
o p 1
optical digital input 1 (select source)
o p 2
- - - . . . c o 1 . . . s c d
- - - . . . c o 2 . . . s c d
r c 5
d a t
optical digital input 2 (select source)
c o 1
coaxial digital input 1 (select source)
c o 2
coaxial digital input 2 (select source)
e x t
remote control
note
Analog inputs 1 and 2 can be
combined to provide one 8
channel or 6 channel input. In
either case input 2 is then
unavailable. For a complete
description of this facility see
Sections 7 and 9.
note
The final three stages of the
input setup routine provide
adjustment for three Dolby
Surround Pro Logic II music
programme decode parameters.
It is not necessary to set these
parameters initially. See
Section 9 for detailed
information on these decode
parameters.
note
With DAT (data) selected for
the EXT parameter RC5 (remote
handset) control is disabled.
RC5 can be re-enabled using
the front panel controls.
Dolby Surround Pro Logic II “Panorama”
Dolby Surround Pro Logic II “Dimension”
Dolby Surround Pro Logic II “Centre Width”
D
w
P a n
o f f
o n
0 0 - 0 7
0 0 - 0 6