1. DL manuals
  2. Oki
  3. Printer
  4. C9600 Series
  5. Network And Configuration Manual

Oki C9600 Series Network And Configuration Manual

Summary of C9600 Series

  • Page 1

    59367301_cvr.Jpg.

  • Page 2: Copyright Information

    Okilan 8200e network user’s guide 2 copyright information copyright © 2007 by oki data americas, inc. All rights reserved document information okilan 8200e network user’s guide p/n 59367301, revision 2.0 february, 2007 disclaimer every effort has been made to ensure that the information in this docu...

  • Page 3: Contents

    Okilan 8200e network user’s guide 3 contents copyright information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 note and important boxes. . . . . . . . . . . . . . . . . . . . . . . . . . 7 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 sectio...

  • Page 4

    Okilan 8200e network user’s guide 4 oki lpr printing utility . . . . . . . . . . . . . . . . . . . . . . . . 125 system requirements . . . . . . . . . . . . . . . . . . . . . . . 125 installing oki lpr . . . . . . . . . . . . . . . . . . . . . . . . . . 125 using oki lpr. . . . . . . . . . . . . . ....

  • Page 5

    Okilan 8200e network user’s guide 5 section 6: printing using unix . . . . . . . . . . . . . . . . . . . . 182 overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 configuring the print server . . . . . . . . . . . . . . . . . . . . 184 configuring the operating system . ....

  • Page 6

    Okilan 8200e network user’s guide 6 security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 connection error in web browser . . . . . . . . . . . . . . . 215 cannot print. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 cannot install the ca certificate. . . . ...

  • Page 7: Note and Important Boxes

    Okilan 8200e network user’s guide 7 note and important boxes note a note appears like this. A note provides additional information to supplement the main text which helps you to use and understand the product. Important! An important message appears like this. An important message provides supplemen...

  • Page 8: Introduction

    Okilan 8200e network user’s guide 8 introduction general information the okilan ® internal print server is a fast 100base-tx/10base-t network interface. This network print server supports ieee 802.2, ieee 802.3, ethernet-ii and snap, and can detect those frame types automatically. It supports major ...

  • Page 9: Sections

    Okilan 8200e network user’s guide 9 sections this book is divided into the following sections: 䊳 “section 1: configuring the print server” on page 15 䊳 “section 2: utilities” on page 120 䊳 “section 3: security features” on page 129 䊳 “section 4: printing from micosoft windows” on page 159 䊳 “section...

  • Page 10: Print Server Specifications

    Okilan 8200e network user’s guide 10 print server specifications cpu falcon frame types • ieee 802.2 • ieee 802.3 • ethernet-ii, snap, auto network interface • 100base-tx • 10base-t network protocols • tcp/ip – network layer: arp, rarp, ip, icmp, pnp – session layer: tcp, udp – application layer: pr...

  • Page 11

    Okilan 8200e network user’s guide 11 supported operating systems • windows – xp – 2000 – nt 4.0 – me / 98 • novell netware – 3.12j, 3.2j – 4.11j – 5.0 – 6.0 • unix – solaris 2.4, 2.6, 7, 8 – sun os 4.X.X – hp-ux 9.0.3 – aix 4.3.1 • macintosh – os 10.1, 10.2x, 10.3x print service • lpr • ftp • port 9...

  • Page 12: Self-Diagnostic Test

    Okilan 8200e network user’s guide 12 self-diagnostic test with the printer power switched on, press the print server test button for more than three seconds and release. The self-diagnostic test results (normally “ok”) and network information configuration settings are printed. The printout contains...

  • Page 13: Available Utilities

    Okilan 8200e network user’s guide 13 available utilities you can configure the print server by using one of the following utilities: utility features system requirements quick setup (see page 16) configure the print server easily and simply without installing any software packages into your system. ...

  • Page 14

    Okilan 8200e network user’s guide 14 adminmanage r (see page 25) configure the print server in detail. Windows* • xp • 2000 • nt 4.0 • me • 95/98 * with tcp/ip protocol or ipx/spx protocol installed. To create a netware queue, netware client 32 or intranetware client should be installed in your syst...

  • Page 15: General Information

    Okilan 8200e network user’s guide 15 section 1: configuring the print server general information this section explains the various ways you can configure your print server. It consists of the following: 䊳 using adminmanager quick setup (page 16) 䊳 using a web browser (page 19) 䊳 using adminmanager s...

  • Page 16: Configuration:

    Okilan 8200e network user’s guide 16 configuration: using adminmanager quick setup introduction the adminmanager quick setup utility allows you to configure the print server easily and simply without installing any software packages. You can configure the following: • enable/disable tcp/ip, netware,...

  • Page 17: Using Quick Setup

    Okilan 8200e network user’s guide 17 using quick setup cd.Jpg 1. Insert the drivers cd provided with your printer into the cd-rom drive and wait for it to autorun. If the menu installer does not start automatically, click [start] → [run] → [browse]. Browse to your cd-rom and click [install] → [open]...

  • Page 18

    Okilan 8200e network user’s guide 18 the new settings are transmitted to the network card, but the network card is still operating with pre-transmission settings. 11. Click [finish] to validate the new settings. The print server reinitializes..

  • Page 19: Configuration:

    Okilan 8200e network user’s guide 19 configuration: using a web browser if the print server is connected to the network using tcp/ip, its settings and the printer menu settings can be configured using a web browser such as • microsoft internet explorer version 5.5 and higher or • netscape navigator ...

  • Page 20: Note

    Okilan 8200e network user’s guide 20 3. Enter the print server’s ip address: internet explorer enter the print server’s ip address in the [address] field. Netscape navigator enter the print server’s ip address in the [location/position] field. 4. Press the enter key. The printer status window appear...

  • Page 21: Note

    Okilan 8200e network user’s guide 21 5. To ensure correct operation, change the following browser setting: microsoft internet explorer a. In the tools pull-down menu, select [internet options]. B. On the [general] tab, under [temporary internet files], click [settings…]. C. Under [check for newer ve...

  • Page 22

    Okilan 8200e network user’s guide 22 8. Enter “root” for the [user name] and your password—the default is the last six digits of the mac address—under [password]. Explorer_pasword.Bmp 9. Click [ok]..

  • Page 23: Using The Web Browser

    Okilan 8200e network user’s guide 23 using the web browser 8200e_webadmin_ready.Jpg 1. Click on a tab to access the settings for a particular category. 2. In the left column, click the category for which you wish to make changes. 3. When you are done making changes, click [submit] to send the to the...

  • Page 24: Changing The Password

    Okilan 8200e network user’s guide 24 changing the password 1. Open the browser and enter the ip address for the print server, then login with your current password. 2. Click [security] → [password configuration]. 8200e_security_password_config.Jpg 3. Under [administrator(root) password configuration...

  • Page 25: Configuration:

    Okilan 8200e network user’s guide 25 configuration: using adminmanager standard setup adminmanager standard setup is a powerful microsoft windows-based utility for configuring all print server functions using a graphical user interface. Configuration requires a pc with one of the following windows ®...

  • Page 26: Installing Adminmanager

    Okilan 8200e network user’s guide 26 installing adminmanager cd.Jpg 1. Insert the drivers cd provided with your printer into the cd-rom drive and wait for it to autorun. If the menu installer does not start automatically, click [start] → [run] → [browse]. Browse to your cd-rom and click [install] → ...

  • Page 27

    Okilan 8200e network user’s guide 27 the welcome window appears. Adminmgr_std_welcome.Bmp here you can choose: – run the utility from the cd [execute from cd-rom] or – load the utility onto your hard drive and run it from there [install and execute]. 9. Click [next]. A. If you selected [install and ...

  • Page 28: The Adminmanager Interface

    Okilan 8200e network user’s guide 28 the adminmanager interface adminmgr_interface1.Bmp pull-down menus file menu • search: locates and lists all printers in your network which have the okilan 8200e installed. • exit exit the program. Status menu • printer status displays the current status of the p...

  • Page 29: Setup Menu

    Okilan 8200e network user’s guide 29 • system status displays the current network card configuration. The configuration data can be saved as a log file. • netmeter displays the current network status. For more information, see the netmeter on-line help file. • list of configuration items displays cu...

  • Page 30: Note

    Okilan 8200e network user’s guide 30 general tab (oki device setup) 8200e_adminmgr_general_tab.Bmp the general tab allows you to change the admin password, snmp write community name and snmp read community name. 1. Click [change]. A. Enter the current value, then enter the new value and re-enter it ...

  • Page 31

    Okilan 8200e network user’s guide 31 tcp/ip tab (oki device setup) 8200e_adminmgr_tcpip_tab.Bmp item comments use tcp/ip protocol enable/disable tcp/ip protocol. Use dhcp/bootp click to select this item if the ip address, subnet mask, default gateway and ip addresses for dns primary server and secon...

  • Page 32

    Okilan 8200e network user’s guide 32 default gateway set the default gateway of the selected network interface card. Auto discovery… use to enable/disable network pnp and rendezvous, and to set the device name. Dns server… set ip addresses for dns primary and secondary servers. Wins server… use to s...

  • Page 33

    Okilan 8200e network user’s guide 33 netware tab (oki device setup) 8200e_adminmgr_netware_tab.Bmp item comments use netware protocol enable/disable netware protocol. Use ipx protocol click to deselect if you do not wish to use ipx. Use tcp/ip protocol click this to select tcp/ip protocol. Print ser...

  • Page 34

    Okilan 8200e network user’s guide 34 [bindery setup] check box. Click to deselect bindery. When bindery setup is deselected, the [bindery setup…] button is greyed out. Bindery setup configure bindery mode items, including: file server to be connected. Select up to 8 file servers to connect. Password...

  • Page 35

    Okilan 8200e network user’s guide 35 ethertalk tab (oki device setup) 8200e_adminmgr_ethertalk_tab.Bmp item comments use ethertalk protocol enable/disable ethertalk protocol. Printer name set the ethertalk printer object name. Zone name set the name of the zone to which the print server belongs..

  • Page 36

    Okilan 8200e network user’s guide 36 netbeui tab (oki device setup) 8200e_adminmgr_netbeui_tab.Bmp item comments use netbeui protocol enable/disable netbeui protocol. Short printer name set a computer name for the print server. Workgroup set a name for the work group to which the print server belong...

  • Page 37: Snmp Tab (Oki Device Setup)

    Okilan 8200e network user’s guide 37 snmp tab (oki device setup) 8200e_adminmgr_snmp_tab.Bmp item comments authentic community this community name is used to check whether or not incoming snmp requests have the correct community name. The community name is displayed as ****** for security reasons. T...

  • Page 38

    Okilan 8200e network user’s guide 38 printer trap setup… the following items can be configured: printer trap community name this community name is assigned to outgoing printer status traps such as off-line, paper out, etc. Tcp #1 through tcp #5 set up to five ip addresses to which a trap packet will...

  • Page 39: E-Mail(Send) Tab

    Okilan 8200e network user’s guide 39 e-mail(send) tab 8200e_adminmgr_emailsend_tab.Bmp item comments use smtp transmit enable/disable sending e-mail using smtp. Smtp server name set the host name of the smtp server. Printer e-mail address set the e-mail address that is used in the [from] field in th...

  • Page 40

    Okilan 8200e network user’s guide 40 destination address 1… through 5… set the following parameters: destination address set e-mail address to which e-mail should be sent. Notify mode select period or event. When period is selected: check time used to set the interval at which the selected events ar...

  • Page 41

    Okilan 8200e network user’s guide 41 when event is selected event mode select on, off or nowait (e-mail is sent as soon as the event occurs) for the following events. If on is selected, the check interval is settable in hours and/or minutes (0, 15, 30, or 45). See the descriptions for period mode ab...

  • Page 42

    Okilan 8200e network user’s guide 42 authentication… used to set the following security information: use smtp authenticatio n enable/disable smtp authentication. User id set the user id for authentication. User password set a password for authentication. Others… set the following items: smtp port nu...

  • Page 43

    Okilan 8200e network user’s guide 43 e-mail(receive) tab (oki device setup) the print server supports an e-mail reception function (pop3) allowing the printer to print pdf and text files attached to emails. Not all printers support this function. If the pop tab is not displayed, your printer does no...

  • Page 44

    Okilan 8200e network user’s guide 44 pop detail… set the following: use apop select if you want to use apop. Pop3 port number set the port number for apop (default is 110). Mail polling time. Set interval to retrieve e-mail(s) from the pop3 server. Selectable values, off, 1min, 5min (default), 10min...

  • Page 45: Sntp Tab (Oki Device Setup)

    Okilan 8200e network user’s guide 45 sntp tab (oki device setup) 8200e_adminmgr_sntp_tab.Bmp item comments use sntp enable/disable sntp (simple network time protocol). Ntp server 1 address set the ip address or host name for ntp server 1. Ntp server 2 address set the ip address or host name for ntp ...

  • Page 46

    Okilan 8200e network user’s guide 46 local time zone set the local time zone from -12:00 to +13:00. Minute interval is selectable from 00 (the default), 15, 30 or 45. Daylight saving when this is selected, one hour is added to the local time. Item comments.

  • Page 47

    Okilan 8200e network user’s guide 47 maintenance tab (oki device setup) 8200e_adminmgr_maintenance_tab.Bmp item comments lan scale select normal (the default) or small..

  • Page 48

    Okilan 8200e network user’s guide 48 ip filter setup… the following items can be configured: use ip filter enable/disable ip filtering. Default is disabled. Admin ip address enter the printer’s ip address. Ip address range set up to 10 ip filter address ranges: [ip filter range 1] through [iip filte...

  • Page 49

    Okilan 8200e network user’s guide 49 ssl/tls tab (oki device setup) see “section 3: security features” starting on page 129 for more information. 8200e_adminmgr_ssltls_tab.Bmp item comments encryption strength set the strength of encryption: • strong = highest security, slowest speed • standard = me...

  • Page 50

    Okilan 8200e network user’s guide 50 self-signed certificate for ipp encryption within an organization’s internal network (intranet). Requires windows xp or 2000. See page 133 for more information. Create certificate… when self-signed certificate is selected, the following items are configured: comm...

  • Page 51

    Okilan 8200e network user’s guide 51 ca-signed certificate… used for web encryption to provide security when printing over the internet. Requires an outside certification service which must be purchased separately. See page 144 for more information. Create certificate… when ca-signed certificate is ...

  • Page 52: Note

    Okilan 8200e network user’s guide 52 䊳 setup by http launches the default browser in your environment to access the selected printer’s web page. 䊳 setup by telnet launches the telnet application in your environment to access the selected printer’s telnet port. 䊳 create netware queues use this to cre...

  • Page 53

    Okilan 8200e network user’s guide 53 d. Follow the on-screen instructions. E. Confirm your configuration. If it is correct, select [execute]. F. Select [finish] button. If necessary, select [setup] → [oki device setup] and continue your configuration. 䊳 delete netware object use this to delete a net...

  • Page 54: Note

    Okilan 8200e network user’s guide 54 c. When done, click [quit] 䊳 reset resets the selected network interface card. 䊳 test print prints the self-diagnostic test pages (see page 12). 䊳 ip address setup sets the static ip address of the network interface card manually. If you only use tcp/ip and the p...

  • Page 55: Option Menu

    Okilan 8200e network user’s guide 55 option menu 䊳 use tcp/ip protocol if this item is selected, adminmanager uses tcp/ip protocol to search/configure network interface cards. 䊳 use ipx/spx protocol if this item is selected, adminmanager uses ipx/spx protocol to search/configure network interface ca...

  • Page 56

    Okilan 8200e network user’s guide 56 tcp/ip tab (environmental setup) 8200e_adminmgr_environ_tcpip_tab.Bmp item comments use tcp/ip protocol enable/disable tcp/ip protocol. The default is enabled. If disabled, the search will not be carried out using tcp/ip. Set broadcast address set broadcast addre...

  • Page 57

    Okilan 8200e network user’s guide 57 netware tab (environmental setup) 8200e_adminmgr_environ_netware_tab.Bmp item comments use netware protocol enable/disable netware protocol. The default is enabled. If disabled, the search will not be carried out using netware. Auto search if [auto search] is sel...

  • Page 58

    Okilan 8200e network user’s guide 58 delete select a network number in the list box, then click [delete] to remove it. Item comments.

  • Page 59: Help Menu

    Okilan 8200e network user’s guide 59 timeout tab (environmental setup) 8200e_adminmgr_environ_timeout_tab.Bmp help menu • about provides software version and copyright information. Item comments set timeout: printer search [search every (20-180sec)] set the response waiting time from the network car...

  • Page 60: Configuration:

    Okilan 8200e network user’s guide 60 configuration: using telnet example telnet configuration, sun solaris 2.4 telnet requires the print server to have a valid ip address configured. If the nic already has an ip address configured, skip steps 1 to 3 below. 1. Login as [root]. If you do not have supe...

  • Page 61

    Okilan 8200e network user’s guide 61 3. Use the ping command to confirm the connection with the network card. Example for ip address 172.168.20.127: # ping 172.168.20.127 if there is no reply, there is a problem with the configuration of the ip address (the ip address has been already set manually o...

  • Page 62: Note

    Okilan 8200e network user’s guide 62 you should see the following sequence of responses: trying 172.168.20.127 connected to 172.168.20.127 escape character is ‘^]’. Ethernetboard okilan printer". Login: root ‘root’ user needs password to login. Password: user ‘root’ logged in. No. Message value (lev...

  • Page 63

    Okilan 8200e network user’s guide 63 telnet hierarchical structure table for information on how to set the various reference numbers using adminmanager or web browser, see the "summary of non-security configurable items" table starting on page 70. Level1 level2 level3 ref no. Setup tcp/ip tcp/ip pro...

  • Page 64

    Okilan 8200e network user’s guide 64 3: setup netware netware protocol — netware-1 packet type — netware-2 netware mode — netware-3 setup pserver mode fserver name 1 netware-3 fserver name 2 netware-4 fserver name 3 netware-4 fserver name 4 netware-4 fserver name 5 netware-4 fserver name 6 netware-4...

  • Page 65

    Okilan 8200e network user’s guide 65 3: setup netware 5: setup rprinter mode pserver name 1 netware- 11 pserver name 2 netware- 11 pserver name 3 netware- 11 pserver name 4 netware- 11 pserver name 5 netware- 11 pserver name 6 netware- 11 pserver name 7 netware- 11 pserver name 8 netware- 11 job tim...

  • Page 66

    Okilan 8200e network user’s guide 66 5: setup netbeui netbeui protocol — netbeui-1 computer name — netbeui-2 workgroup name — netbeui-3 comment — netbeui-4 99: back to prior menu — — 6: setup printer port netware port name — port-1 ethertalk port name — port-2 boj string — port-3 eoj string — port-4...

  • Page 67

    Okilan 8200e network user’s guide 67 8: setup printer trap prn-trap community — trap-1 setup tcp#1 trap setup tcp#2 trap setup tcp#3 trap setup tcp#4 trap tcp#1—5 trap enable trap-2 on-line trap trap-3 off-line trap trap-4 paper out trap trap-5 paper jam trap trap-6 cover open trap trap-7 printer er...

  • Page 68

    Okilan 8200e network user’s guide 68 9: setup smtp (e-mail) smtp transmit — smtp-1 smtp receive — smtp-2 smtp server name — smtp-3 smtp port number — smtp-4 e-mail address — smtp-5 reply-to address — smtp-6 event to address 1 event to address 2 event to address 3 event to address 4 event to address ...

  • Page 69

    Okilan 8200e network user’s guide 69 10: setup pop (e-mail) pop3 protocol — pop-1 pop3 server — pop-2 pop port number — pop-3 pop3 server userid — pop-4 pop3 server password — pop-5 use apop — pop-6 retrieve every (min.) — pop-7 99: back to prior menu — — 97: reset to factory set — — etc-1 98: quit ...

  • Page 70: Configuration:

    Okilan 8200e network user’s guide 70 configuration: configurable items summary of non-security configurable items • tcp/ip: see page 71 • snmp: see page 74 • netware: see page 78 • ethertalk: see page 84 • netbeui: see page 85 • port: see page 87 • status: see page 95 • trap: see page 96 • smtp: see...

  • Page 71: Tcp/ip

    Okilan 8200e network user’s guide 71 tcp/ip tcpip-1 enable / disable tcp/ip protocol. Default setting: enable adminmanager [setup] → [oki device setup] → [tcp/ip] → [use tcp/ip protocol] web browser tcp/ip protocol cannot be disabled using web browser. Telnet [setup tcp/ip] → [tcp/ip protocol] tcpip...

  • Page 72: Tcpip-4

    Okilan 8200e network user’s guide 72 tcpip-4 set gateway (the default route), 0.0.0.0 to 255.255.255.255. Default setting: 0.0.0.0 adminmanager [setup] → [oki device setup] → [tcp/ip] → [default gateway] web browser [network] → [tcp/ip] → [change settings] → [set ip address manually] → [default gate...

  • Page 73: Tcpip-7

    Okilan 8200e network user’s guide 73 tcpip-7 set ip address for primary dns server, 0.0.0.0 to 255.255.255.255. Default setting: 0.0.0.0 adminmanager [setup] → [oki device setup] → [tcp/ip] → [dns server…] → [primary server] web browser [network] → [tcp/ip] → [step2 (optional)change other tcp/ip set...

  • Page 74: Snmp

    Okilan 8200e network user’s guide 74 snmp snmp-1 community name used to check incoming snmp requests. Displayed as asterisks (***) for security reasons. Up to 15 alphanumeric characters. Default setting: public adminmanager [setup] → [oki device setup] → [snmp] → [authentic community] web browser no...

  • Page 75: Snmp-3

    Okilan 8200e network user’s guide 75 snmp-3 destination ip address of trap packet. Range 0.0.0.0 (trap disabled) to 255.255.255.255. Default setting: 0.0.0.0 adminmanager [setup] → [oki device setup] → [snmp] → [trap address] web browser [network] → [snmp trap] → [step2] → [address 1 [2, 3, etc.]] t...

  • Page 76: Snmp-5

    Okilan 8200e network user’s guide 76 snmp-5 set the sysname (printer model name). Up to 255 alphanumeric characters. Default setting: null adminmanager [setup] → [oki device setup] → [snmp] → [mib-ii parameters] → [sysname] web browser not availabl telnet [setup snmp] → [sysname] snmp-6 set the sysl...

  • Page 77: Snmp-7

    Okilan 8200e network user’s guide 77 snmp-7 set ttl (time to live), 0 to 255. Default setting: 0 adminmanager not available web browser not available telnet [setup snmp] → [default ttl] snmp-8 set the authentic trap, 1 (enabled)/ 2 (disabled). Default setting: 2 (disabled) adminmanager not available...

  • Page 78: Netware

    Okilan 8200e network user’s guide 78 netware netware-1 enable/disable netware protocol. Default setting: enable adminmanager [setup] → [oki device setup] → [netware] → [use netware protocol] web browser [security] → [protocol on/off] → [netware] or [network] → [general network settings] → [protocol ...

  • Page 79: Netware-3

    Okilan 8200e network user’s guide 79 netware-3 set the netware mode as rprinter or pserver. Default setting: pserver adminmanager [setup] → [oki device setup] → [netware] → [operation mode] web browser [network] → [netware] → [step1. Select netware mode] telnet [setup netware] → [netware mode] netwa...

  • Page 80: Netware-5

    Okilan 8200e network user’s guide 80 netware-5 sets print server name. Up to 31 alphanumeric characters per name. Default includes the last six digits of the mac address. Default setting: default includes the last six digits of the mac address adminmanager [setup] → [oki device setup] → [netware] → ...

  • Page 81: Netware-7

    Okilan 8200e network user’s guide 81 netware-7 set the print job polling interval for print server. Range 2 to 255 seconds. Default setting: 4 seconds adminmanager [setup] → [oki device setup] → [netware] → [bindery setup] → [job polling time] web browser [network] → [netware] → [to step2] → [step4....

  • Page 82: Netware-9

    Okilan 8200e network user’s guide 82 netware-9 set the nds tree name. Up to 31 alphanumeric characters per name. Default setting: null adminmanager [setup] → [oki device setup] → [netware] → [deselect bindery setup…] → [nds setup…] → [nds tree] web browser [network] → [netware] → [to step2] → [step5...

  • Page 83: Netware-11

    Okilan 8200e network user’s guide 83 netware-11 set up to eight print servers to connect. Up to 47 alphanumeric characters per server. Default setting: null adminmanager [setup] → [oki device setup] → [netware] → [select rprinter mode] → [rprinter setup…] web browser [network] → [netware] → [step1. ...

  • Page 84: Ethertalk

    Okilan 8200e network user’s guide 84 ethertalk ethertalk-1 enable/disable ethertalk. Default setting: enable adminmanager [setup] → [oki device setup] → [ethertalk] → [use ethertalk protocol] web browser [security] → [protocol on/off] → [ethertalk] or [network] → [general network settings] → [protoc...

  • Page 85: Netbeui

    Okilan 8200e network user’s guide 85 netbeui netbeui-1 enable/disable netbeui. Default setting: enable adminmanager [setup] → [oki device setup] → [netbeui] → [use netbeui protocol] web browser [security] → [protocol on/off] → [netbeui] or [network] → [general network settings] → [protocol options] ...

  • Page 86: Netbeui-3

    Okilan 8200e network user’s guide 86 netbeui-3 set a workgroup name to which the print server belongs. Up to 15 alphanumeric characters per name, default is printserver. Default setting: printserver adminmanager [setup] → [oki device setup] → [netbeui] → [workgroup] web browser [network] → [netbeui]...

  • Page 87: Port

    Okilan 8200e network user’s guide 87 port port-1 set the netware printer object name. Up to 31 alphanumeric characters. Default is ol + last six digits of the mac address + -prn1. Default setting: ol + last six digits of the mac address + -prn1 adminmanager [setup] → [oki device setup] → [netware] →...

  • Page 88: Port-2

    Okilan 8200e network user’s guide 88 port-2 set the ethertalk printer object name, up to 32 alphanumeric characters. Default setting: the printer name on which the print server is installed adminmanager [setup] → [oki device setup] → [ethertalk] → [printer name] web browser [network] → [ethertalk] →...

  • Page 89: Port-4

    Okilan 8200e network user’s guide 89 port-4 set an appropriate command sequence to be sent to the connected printer after printing a job. Combination of alphanumeric characters and the following control characters, up to a maximum of 31 characters: \b backspace (0x08) \t tab (0x09) linefeed (0x0a...

  • Page 90: Port-5

    Okilan 8200e network user’s guide 90 port-5 set an appropriate command sequence to be sent to the connected printer before printing a job when data is sent to the sjis/euc logical printer/directory. Combination of alphanumeric characters and the following control characters, up to a maximum of 31 ch...

  • Page 91: Port-6

    Okilan 8200e network user’s guide 91 port-6 set an appropriate command sequence to be sent to the connected printer after printing a job when data is sent to the sjis/euc logical printer/directory. Combination of alphanumeric characters and the following control characters, up to a maximum of 31 cha...

  • Page 92: Port-7

    Okilan 8200e network user’s guide 92 port-7 set a printer type when data is sent to the sjis/euc logical printer/directory. Default setting: ps adminmanager not applicable web browser not applicable telnet [setup printer port] → [printer type] port-8 set the number of tabs when data is sent to the s...

  • Page 93: Port-9

    Okilan 8200e network user’s guide 93 port-9 set page width when data is sent to the sjis/euc printer/directory. Range 0 to 255 characters. Default is 78 characters. If the width of one line exceeds this value, a cr and lf are inserted automatically. When 0 is selected, there is no limitation of the ...

  • Page 94: Port-11

    Okilan 8200e network user’s guide 94 port-11 set banner printing for lpr/ftp enabled/disabled. Default setting: disabled adminmanager not applicable web browser not applicable telnet [setup printer port] → [lpr/ftp banner].

  • Page 95: Status

    Okilan 8200e network user’s guide 95 status status-1 display the logical port status. Default setting: x adminmanager [status] → [printer status] web browser [status] → [printer status] telnet [display status] → [prn1] status-2 display the system status. Default setting: x adminmanager [status] → [s...

  • Page 96: Trap

    Okilan 8200e network user’s guide 96 trap trap-1 sets community name assigned to outgoing printer status traps such as off-line, paper out, etc. Up to 77 alphanumeric characters. Default is public. Default setting: public adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → ...

  • Page 97: Trap-3

    Okilan 8200e network user’s guide 97 trap-3 enable/disable sending a trap when the printer goes on-line. Default setting: x adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [tcp #!–5] → [detail …] → [trap enable] → [on-line] web browser [network] → [snmp trap] → [step3. ...

  • Page 98: Trap-5

    Okilan 8200e network user’s guide 98 trap-5 enable/disable sending a trap when the paper is out. Default setting: disable adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [tcp #!–5] → [detail …] → [trap enable] → [paper out] web browser [network] → [snmp trap] → [step3. ...

  • Page 99: Trap-7

    Okilan 8200e network user’s guide 99 trap-7 enable/disable sending a trap when the printer cover is opened. Default setting: disable adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [tcp #!–5] → [detail …] → [trap enable] → [cover open] web browser [network] → [snmp trap...

  • Page 100: Trap-9

    Okilan 8200e network user’s guide 100 trap-9 set up to five ip addresses to which a trap packet is sent. 0.0.0.0 to 255.255.255.255. Default setting: 0.0.0.0 adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [tcp #!–5] web browser [network] → [snmp trap] → [step2. Set pri...

  • Page 101: Trap-11

    Okilan 8200e network user’s guide 101 trap-11 enable/disable sending a trap when the printer is set to on-line. Default setting: disable adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [ipx] → [detail …] → [trap enable] → [on-line] web browser [network] → [snmp trap] → ...

  • Page 102: Trap-13

    Okilan 8200e network user’s guide 102 trap-13 enable/disable sending a trap when paper is out. Default setting: disable adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [ipx] → [detail …] → [trap enable] → [paper out] web browser [network] → [snmp trap] → [step3. Set pri...

  • Page 103: Trap-15

    Okilan 8200e network user’s guide 103 trap-15 enable/disable sending a trap when the printer cover is opened. Default setting: disable adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [ipx] → [detail …] → [trap enable] → [cover open] web browser [network] → [snmp trap] →...

  • Page 104: Trap-17

    Okilan 8200e network user’s guide 104 trap-17 set the node address to which a trap packet is sent. Any address. Default is 00000000000. Default setting: 00000000000 adminmanager [setup] → [oki device setup] → [snmp] → [printer trap setup …] → [ipx] web browser [network] → [snmp trap] → [step2. Set p...

  • Page 105: Smtp

    Okilan 8200e network user’s guide 105 smtp smtp-1 enable/disable receiving e-mail via smtp. Default setting: disable adminmanager [setup] → [oki device setup] → [e-mail(receive)] → [use smtp receive] web browser [network] → [email] → [receive settings] → [smtp] → [to step2] → [domain filter] telnet ...

  • Page 106: Smtp-3

    Okilan 8200e network user’s guide 106 smtp-3 set the ip address or host name of the smtp server. Address: 0.0.0.0 to 255.255.255.255. Host name = up to 64 characters: default is null. Default setting: null adminmanager [setup] → [oki device setup] → [e-mail(send)] → [smtp server name] web browser [n...

  • Page 107: Smtp-5

    Okilan 8200e network user’s guide 107 smtp-5 set the e-mail address used for the [from] field in the mail header. Up to 78 alphanumeric characters. Default is null. Default setting: null adminmanager [setup] → [oki device setup] → [e-mail(send)] → [printer e-mail address] web browser [network] → [em...

  • Page 108: Smtp-7

    Okilan 8200e network user’s guide 108 smtp-7 set up to five e-mail addresses to which e-mail is sent. Up to 78 alphanumeric characters per address. Default is null. Default setting: null adminmanager [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [destination addres...

  • Page 109: Smtp-9

    Okilan 8200e network user’s guide 109 smtp-9 enable/disable sending an e-mail when the printer is off-line. Default setting: disable adminmanager not applicable web browser not applicable telnet [setup smtp (e-mail)] → [event to address 1–5] → [off line] smtp-10 enable/disable sending an e-mail when...

  • Page 110: Smtp-11

    Okilan 8200e network user’s guide 110 smtp-11 enable/disable sending an e-mail when the toner is low or out. Default setting: x adminmanager by event: [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [notify mode = event] → [event mode] → [consumable warning = on or n...

  • Page 111: Smtp-13

    Okilan 8200e network user’s guide 111 smtp-13 enable/disable sending an e-mail when a paper jam occurs. Default setting: disable adminmanager by event: [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [notify mode = event] → [event mode] → [printing error = on or nowa...

  • Page 112: Smtp-15

    Okilan 8200e network user’s guide 112 smtp-15 enable/disable sending an e-mail when a stacker error occurs. Default setting: disable adminmanager by event: [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [notify mode = event] → [event mode] → [printing error = on or ...

  • Page 113: Smtp-17

    Okilan 8200e network user’s guide 113 smtp-17 enable/disable sending an e-mail when a recoverable error occurs. Default setting: disable adminmanager by event: [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [notify mode = event] → [event mode] → [print result error ...

  • Page 114: Smtp-19

    Okilan 8200e network user’s guide 114 smtp-19 enable/disable sending an e-mail when a finisher error occurs. Default setting: disable adminmanager by event: [setup] → [oki device setup] → [e-mail(send] → [destination address] → [1…–5…] → [notify mode = event] → [event mode] → [printing error = on or...

  • Page 115: Pop

    Okilan 8200e network user’s guide 115 pop pop-1 enable/disable retrieving e-mail via pop3. Default setting: disable adminmanager [setup] → [oki device setup] → [e-mail(receive)] → [use pop receive] web browser [network] → [email] → [receive settings] → [pop3] telnet [setup pop (e-mail)] → [pop3 prot...

  • Page 116: Pop-3

    Okilan 8200e network user’s guide 116 pop-3 set the port number of pop. Range 1 to 65536. Default setting: 110 adminmanager [setup] → [oki device setup] → [e-mail(receive)] → [pop detail…] → [pop3 port number] web browser [network] → [email] → [receive settings] → [select pop3] → [to step2] → [step2...

  • Page 117: Pop-5

    Okilan 8200e network user’s guide 117 pop-5 set the password for the pop3 server. Up to 16 alphanumeric characters. Default setting: null adminmanager [setup] → [oki device setup] → [e-mail(receive)] → [pop3 server password] web browser [network] → [email] → [receive settings] → [select pop3] → [to ...

  • Page 118: Pop-7

    Okilan 8200e network user’s guide 118 pop-7 set the interval to retrieve e-mails from the pop3 server. Off, 1 min, 5 min, 10 min, 30 min, 60 min. Default setting: off adminmanager [setup] → [oki device setup] → [e-mail(receive)] → [pop detail…] → [mail polling time] web browser [network] → [email] →...

  • Page 119: Etc

    Okilan 8200e network user’s guide 119 etc etc-1 reset the print server to the factory defaults. Default setting: not applicable adminmanager [setup] → [reset] web browser [maintenance] → [reset / restore] → [reset printer] telnet [reset to factory set] etc-2 display printer serial number. Default se...

  • Page 120: Section 2: Utilities

    Okilan 8200e network user’s guide 120 section 2: utilities this section covers the following: 䊳 printsupervision management utility (page 121) 䊳 oki lpr printing utility (page 125).

  • Page 121: Utilities:

    Okilan 8200e network user’s guide 121 utilities: printsupervision management utility printsupervision is a web-based application for managing printing devices connected to a network. It consists of two parts: • a web application based on microsoft web server (internet information server, iis or pers...

  • Page 122: Supported Browsers

    Okilan 8200e network user’s guide 122 supported browsers • internet explorer (ie) 5.5 and above. • netscape navigator 6.2 and above. • opera 6.0 and above. The printsupervision application can be accessed from any windows ® , macintosh ® , unix ® , or linux ® desktop that supports any of these brows...

  • Page 123: Installing Printsupervision

    Okilan 8200e network user’s guide 123 installing printsupervision cd.Jpg 1. Insert the drivers cd provided with your printer into the cd-rom drive and wait for it to autorun. If the menu installer does not start automatically, click [start] → [run] → [browse]. Browse to your cd-rom and click [instal...

  • Page 124: Help

    Okilan 8200e network user’s guide 124 or • double-click the [printsupervision] icon on the desktop for the printsupervision server. To run printsupervision client 1. Open your web browser. 2. Enter the address http://[fill in the server ip address or host name]/printsupervision. 3. Or, if you change...

  • Page 125: Utilities:

    Okilan 8200e network user’s guide 125 utilities: oki lpr printing utility the oki lpr utility is a utility that allows sending data to printers connected to the network via tcp/ip. The utility redirects printing data to the lpr port of the specified ip address. System requirements oki lpr works with...

  • Page 126: Important!

    Okilan 8200e network user’s guide 126 3. Click [custom install]. 4. Click [printer driver installer]. 5. Select [local printer], then click [next]. 6. Select [lpt1:], then click [next]. 7. Follow the on-screen instructions to complete the driver installation. The driver installs and the program retu...

  • Page 127: Using Oki Lpr

    Okilan 8200e network user’s guide 127 10. When the installation ends, the “setup complete” window appears. 11. Check [yes, i want to launch oki lpr utility now]. 12. Click [finish]. The utility starts. Lpr_status_no_oki.Bmp step 3: add the printer to the utility 1. With the utility open, click the [...

  • Page 128: Uninstalling The Utility

    Okilan 8200e network user’s guide 128 uninstalling the utility 1. Exit the utility: right-click the oki lpr icon in the system tray and click [exit]. 2. Select [start] → [programs] → [okidata] → [oki lpr utility] → [uninstall oki lpr utility]. 3. Click [yes] when the “confirm file deletion” window a...

  • Page 129: Section 3: Security Features

    Okilan 8200e network user’s guide 129 section 3: security features this section covers the following: 䊳 overview (page 130) 䊳 ipp encryption (page 133) 䊳 web encryption (page 144) 䊳 unused protocols (page 157).

  • Page 130: Security Features:

    Okilan 8200e network user’s guide 130 security features: overview this section covers the security features provided with the print server, including: 䊳 ssl / tls 䊳 disabling unused protocols in addition, you can enable • ip filtering (see page 47) • e-mail domain filtering for domains 1 through 5 (...

  • Page 131: Web Encryption Prevents

    Okilan 8200e network user’s guide 131 web encryption prevents • wiretapping wiretap.Jpg • spoofing (impersonating) spoofing.Jpg.

  • Page 132: Unused Protocols

    Okilan 8200e network user’s guide 132 summary of ssl/tls encryption functions unused protocols protocols which are not used by your system can be turned off to prevent unauthorized access through them. Item specifications default security type • ssl version 3.0 • tls version 1.0b na a a.Na = not app...

  • Page 133: Security Features:

    Okilan 8200e network user’s guide 133 security features: ipp encryption setting up ipp encryption process summary step 1: create the self-signed certificate step 2: enable ipp printing at the client stations step 1: create the self-signed certificate using the web browser • requires microsoft intern...

  • Page 134

    Okilan 8200e network user’s guide 134 the default is the last six digits of the mac [ethernet] address, minus any punctuation). 4. Click the [security] tab. 5. On the left side, click [cipher (ssl/tls)]. The “encryption of configuration and print” window appears. 8200e_browser_security_cipher1.Bmp.

  • Page 135: Note

    Okilan 8200e network user’s guide 135 6. Change [ssl/tls] to on. 8200e_browser_security_cipher1_ssl_on.Bmp 7. To change the cipher strength setting, click [cipher level settings] and make your selection, then click [ok]. 8. Make sure [using self-signed certificate] is selected (the default). 8200e_b...

  • Page 136

    Okilan 8200e network user’s guide 136 9. Scroll down and under the [value] column enter the information to be included in the certificate: 8200e_browser_security_cipher1_selfsigned_info.Bmp a. To change the key exchange method or the size of the public key to be attached with the certificate, scroll...

  • Page 137: Using Adminmanager

    Okilan 8200e network user’s guide 137 11. Check the settings. If they are correct, click [ok]. If you need to make changes, click [cancel], make any needed changes and click [ok] to send the revised information to the print server. 12. Click [ok]. The “security alert” window appears. 13. Click [yes]...

  • Page 138

    Okilan 8200e network user’s guide 138 5. Click the [ssl/tls] tab. 8200e_adminmgr_ssltls_tab.Bmp item comments encryption strength set the strength of the encryption. Switching to strong provides greater security, but slower speed. Switching to weak provides the fastest speed, but the least security....

  • Page 139

    Okilan 8200e network user’s guide 139 6. With [self-signed certificate] selected (the default), click [create certificate…]. 7. Enter the appropriate information then click [ok]. A window appears listing the settings you have made. 8. Review the information entered, then click [ok] to accept it. Cre...

  • Page 140

    Okilan 8200e network user’s guide 140 9. Wait for the following window to appear: c9600_cipher_cert_complete.Jpg 10. Click [ok]. The ssl/tls tab window appears. 11. Click [apply]. A window appears containing a summary of your certification selection. 12. Click [ok]. C9600_cipher_cert_ca_adminmgr.Jpg...

  • Page 141: Using The Web Browser

    Okilan 8200e network user’s guide 141 step 2: enable ipp printing at client stations using the web browser • requires microsoft internet explorer version 5.5 and higher or netscape navigator version 6.2 and higher. 1. Open the web browser. 2. Type in the printer’s ip address (refer to the self-diagn...

  • Page 142

    Okilan 8200e network user’s guide 142 [next] → select language → [custom install] → [network software] → [installation/config] → [admin mgr / quick setup] → select language → [oki device standard setup] → [execute from cd-rom]. From your desktop (if you installed the utility from the cd) [start] → [...

  • Page 143

    Okilan 8200e network user’s guide 143 7. Click the box beside [use ipp service] to select it, then click [ok]. 8200e_adminmgr_maint_service.Bmp 8. Click [apply]. A window appears containing a summary of your certification selection. 9. Click [ok]. C9600_cipher_cert_ca_adminmgr.Jpg 10. Click [yes]. T...

  • Page 144: Security Features:

    Okilan 8200e network user’s guide 144 security features: web encryption setting up web encryption process summary step 1: apply to a ca service for a certificate. Step 2: install the certificate on the print server. Step 1: apply for a ca certificate using web browser • requires microsoft internet e...

  • Page 145

    Okilan 8200e network user’s guide 145 5. On the left side, click [cipher (ssl/tls)]. The “encryption of configuration and print” window appears. 8200e_browser_security_cipher1.Bmp 6. Change [ssl/tls] to on. 8200e_browser_security_cipher1_ssl_on.Bmp.

  • Page 146: Note

    Okilan 8200e network user’s guide 146 7. To change the cipher strength setting, click [cipher level settings] and make your selection, then click [ok]. 8. Click [using a certificate which a certification authority signed]. 8200e_browser_security_cipher1_casigned.Bmp note the default setting is stand...

  • Page 147

    Okilan 8200e network user’s guide 147 9. Scroll down and type in the information to be used in the certification: 8200e_browser_security_cipher1_selfsigned_info.Bmp a. To change the key exchange method or the size of the public key to be attached with the certificate, scroll down to the bottom and c...

  • Page 148: Important!

    Okilan 8200e network user’s guide 148 12. Wait for the “send the csr to a certification authority” window to appear. C9600_cipher_send_csr.Jpg 13. Copy the text in the box starting with “begin certificate signing request” and ending with “end certificate signing request”, and submit it to your selec...

  • Page 149: Using Adminmanager

    Okilan 8200e network user’s guide 149 using adminmanager 1. Launch the adminmanager utility: from the drivers cd supplied with your printer [next] → select language → [custom install] → [network software] → [installation/config] → [admin mgr / quick setup] → select language → [oki device standard se...

  • Page 150

    Okilan 8200e network user’s guide 150 item comments encryption strength set the strength of the encryption. Switching to strong provides greater security, but slower speed. Switching to weak provides the fastest speed, but the least security. Self-signed certificate the default type of certificate. ...

  • Page 151: Important!

    Okilan 8200e network user’s guide 151 6. Click [ca-signed certificate], then click [create certificate]. 8200e_adminmgr_ssltls_tab_ca.Bmp 7. Enter the appropriate information then click [ok]. A window appears listing the settings you have made. 8. Review the information entered, then click [ok] to a...

  • Page 152: Using Web Browser

    Okilan 8200e network user’s guide 152 step 2: install the certificate once you receive your certificate from the ca, you must install it, using either the web browser or the adminmanager utility. Keep the certificate text handy as you will be prompted to copy and paste it into the program. Using web...

  • Page 153

    Okilan 8200e network user’s guide 153 6. Copy the certificate text sent by the ca service, starting with “begin certificate” and ending with “end certificate”, and paste it into the “paste your signed certificate(pem) …” box. C9600_cipher_web_signed_ca.Jpg 7. Click [submit]. The “security alert” win...

  • Page 154: Using Adminmanager

    Okilan 8200e network user’s guide 154 using adminmanager 1. Launch the adminmanager utility: from the drivers cd supplied with your printer [next] → select language → [custom install] → [network software] → [installation/config] → [admin mgr / quick setup] → select language → [oki device standard se...

  • Page 155

    Okilan 8200e network user’s guide 155 7. Copy the certificate text sent by the ca service, starting with “begin certificate” and ending with “end certificate”, and paste it into the box, then click [install]. C9600_cipher_admgr_copy_signed_ca.Jpg 8. Wait until the completion acknowledgement window a...

  • Page 156: Note

    Okilan 8200e network user’s guide 156 10. Click [ok]. C9600_cipher_cert_ca_adminmgr.Jpg 11. Click [yes]. The print server reboots with the new certification settings engaged. Printing using web encryption to make connection with the encrypted printer: 1. Open your web browser. 2. Enter the printer’s...

  • Page 157: Security Features:

    Okilan 8200e network user’s guide 157 security features: unused protocols disabling unused protocols disabling unused protocols prevents access to the print server through those protocols. The easiest way to disable unused protocols is to use the web browser. 1. Open the web browser. 2. Enter the pr...

  • Page 158

    Okilan 8200e network user’s guide 158 5. The “protocol on/off” window opens. 8200e_security_protocol_onoff.Jpg 6. Here you can set the various available protocols to enable or disable. 7. When done, click [submit]..

  • Page 159: Note

    Okilan 8200e network user’s guide 159 section 4: printing from micosoft windows this section provides guidelines on how to print over the network from various microsoft windows operating systems. There are numerous ways of printing from windows and the exact set-up will vary depending upon your envi...

  • Page 160: Printing From Windows:

    Okilan 8200e network user’s guide 160 printing from windows: overview this chapter provides guidelines on how to print over the network from various microsoft windows operating systems. There are numerous ways of printing from windows and the exact set-up will vary depending upon your environment. T...

  • Page 161: Printing From Windows:

    Okilan 8200e network user’s guide 161 printing from windows: using tcp/ip protocol installation overview there are a number of options available when printing using tcp/ip for windows. Although there are some differences in configuration options between the various windows platforms, the procedure f...

  • Page 162: Note

    Okilan 8200e network user’s guide 162 see “configuring windows to print to the network printer” on page 167. Step 4: restart your computer. Note if your network environment uses domain names, dns should be enabled and configured on your system. However, this step is not essential to enable network p...

  • Page 163: Installing Tcp/ip Protocol

    Okilan 8200e network user’s guide 163 installing tcp/ip protocol if tcp/ip protocol is not already installed on your computer, follow the instructions below to install it. Windows xp 1. Click [start] → [control panel]. 2. Click [network and internet connection] → [network connection]. 3. Double-clic...

  • Page 164: Windows Nt 4.0

    Okilan 8200e network user’s guide 164 windows nt 4.0 1. Click [start] → [settings] → [control panel]. 2. Double-click the [network] icon. 3. In the” network” window, click the [protocols] tab. 4. If the [tcp/ip protocol] is not listed, click [add]. 5. In the "select network protocol" window, click [...

  • Page 165: Gateway

    Okilan 8200e network user’s guide 165 configuring the ip address, subnet mask and gateway generate a self-diagnostic test printout with the printer connected to the network and switched on, press the test button on the print server for more than three seconds. The ip address, subnet mask and default...

  • Page 166

    Okilan 8200e network user’s guide 166 2. Select the appropriate network card, using the ethernet (mac) address to identify it, and click [setup] → [oki device setup]. 3. Click the [tcp/ip] tab and enter the values for the [ip address], [subnet mask] and [default gateway]. 4. Click [apply]. 5. Close ...

  • Page 167: Printer

    Okilan 8200e network user’s guide 167 configuring windows to print to the network printer windows xp windows xp requires administrator privileges. With windows xp, there are four options for printing using tcp/ip. • oki lpr • microsoft lpr* • port 9100 • ipp * in order to use microsoft lpr, it must ...

  • Page 168: Port 9100

    Okilan 8200e network user’s guide 168 12. Ensure [queue name] is lp and [snmp status enabled] is deselected. 13. Click [ok]. 14. Follow the on-screen instructions to finish the installation. Port 9100 1. Click [start] → [settings] → [control panel] → [printers and other hardware]. 2. Click [printers...

  • Page 169

    Okilan 8200e network user’s guide 169 6. Click [connect to a printer on the internet or on a home or office network] and type the printer url in the text box, e.G. Http:// 172.168.1.31/ipp/lp. 7. Click [next]. 8. Install the printer driver.

  • Page 170: Printer

    Okilan 8200e network user’s guide 170 configuring windows to print to the network printer windows 2000 windows 2000 requires administrator privileges. With windows 2000, there are four options for printing using tcp/ip. • oki lpr • microsoft lpr • port 9100 • ipp oki lpr please follow the procedure ...

  • Page 171: Port 9100

    Okilan 8200e network user’s guide 171 b. In [name of printer or print queue on that server] type lp. 9. Follow the on-screen instructions to finish the installation. Port 9100 1. Click [start] → [settings] → [control panel]. 2. Open the [printers] folder. 3. Double-click [add printer]. 4. Click [nex...

  • Page 172

    Okilan 8200e network user’s guide 172 7. Type the printer url in the text box labelled [connect to a printer in the internet or your intranet], e.G. Http://172.168.1.31/ipp/lp. 8. Click [next]. 9. Install the printer driver..

  • Page 173: Printer

    Okilan 8200e network user’s guide 173 configuring windows to print to the network printer windows nt 4.0 nt 4.0 requires administrator privileges. With windows nt 4.0, you have two options for printing using tcp/ip. They are: • oki lpr • microsoft lpr oki lpr please follow the procedure described un...

  • Page 174: Printer

    Okilan 8200e network user’s guide 174 configuring windows to print to the network printer windows me/98 when printing using tcp/ip, the oki lpr utility is the only option to use. See “installing oki lpr” on page 125..

  • Page 175: Printing From Windows:

    Okilan 8200e network user’s guide 175 printing from windows: using netbeui protocol netbeui (netbios extended user interface) is a protocol that was designed for use on small workgroups or lans. Within windows, netbeui is used for file and printer sharing between computers. It provides a simple meth...

  • Page 176: Installing Netbeui Protocol

    Okilan 8200e network user’s guide 176 installing netbeui protocol windows xp although you can install the netbeui protocol into windows xp, it is not supported. You should be able to use netbeui on lan connections although you will not be able to use this on remote access service connections. 1. Cli...

  • Page 177: Windows Me/98

    Okilan 8200e network user’s guide 177 4. If the [netbeui protocol] is not listed, click [add]. 5. In the "select network protocol" window, click [netbeui protocol. 6. Click [ok]. Windows me/98 1. Click [start] → [settings] → [control panel]. 2. Double-click the [network] icon. 3. Click [configuratio...

  • Page 178: Notes

    Okilan 8200e network user’s guide 178 3. Select the relevant printer driver, then click [properties]. 4. Click the [details] tab. 5. Click [add port] → [network] → [browse]. 6. Double-click [entire network] → [printserver] → [ol07db85]. 7. Click [prn1]. 8. Click ok. 9. Check that [network] is select...

  • Page 179

    Okilan 8200e network user’s guide 179 section 5: printing from novell netware this section consists of the following: 䊳 overview (page 180) 䊳 setup (page 181).

  • Page 180: Overview

    Okilan 8200e network user’s guide 180 printing from novell netware: overview the print server supports the novell netware environment. It is necessary to have netware administrator or supervisor rights to change the configuration. This guide is for netware administrators. It should be read in conjun...

  • Page 181: Setup

    Okilan 8200e network user’s guide 181 printing from novell netware: setup general information follow these steps: 1. Print the self-diagnostic test 2. Create and set up netware printer objects 3. Configure the print server print the self-diagnostic test the print server’s self-diagnostic printout pr...

  • Page 182

    Okilan 8200e network user’s guide 182 section 6: printing using unix the print server supports many protocols such as lpd, ftp, telnet, snmp and ipp, and works within the unix environment. This section consists of the following: 䊳 overview (page 183) 䊳 configuring the print server (page 184) 䊳 confi...

  • Page 183: Printing From Unix:

    Okilan 8200e network user’s guide 183 printing from unix: overview the print server supports many protocols such as lpd, ftp, telnet, snmp and ipp, and works within the unix environment. To use the network card within the unix environment, the following steps are required: step 1: configure the prin...

  • Page 184: Printing From Unix:

    Okilan 8200e network user’s guide 184 printing from unix: configuring the print server the first step in installing the network card under unix is to set up the ip address, subnet mask and gateway. This section explains one way to set them up from a unix workstation. • the network addresses used in ...

  • Page 185

    Okilan 8200e network user’s guide 185 example for ip address 172.168.20.127 # ping 172.168.20.127 if there is no reply, there is a problem with the configuration of the ip address (the ip address has been already set manually or by the dhcp/ rarp server), or with the network. Reset the network inter...

  • Page 186

    Okilan 8200e network user’s guide 186 9 : setup smtp email 97 : reset to factory set 98 : quit setup 99 : exit setup please select (1- 99)? 5. Type 1 and press the enter key. Perform the following settings: please select (1- 99)? 1 no. Message value 1 : tcp/ ip protocol : enable 2 : ip address : 172...

  • Page 187: Printing From Unix:

    Okilan 8200e network user’s guide 187 printing from unix: configuring the operating system this section explains how to configure a printer for major unix operating systems. Sun os 4.X.X (bsd) configuration check the ip address, subnet mask and gateway if an incorrect ip address, subnet mask or gate...

  • Page 188

    Okilan 8200e network user’s guide 188 or by the dhcp/rarp server) or with the network. Reset the network interface card settings to their defaults and then try to set a temporary ip address. If you still have the problem after resetting the network interface card, consult the network manager. 4. Reg...

  • Page 189: Check The Ip Address

    Okilan 8200e network user’s guide 189 7. If lpd is not running, start it by logging in as superuser and executing # /usr/lib/lpd & sun solaris 2.X configuration the procedure below must be used for registering a remote printer. Check the ip address if an incorrect ip address is entered, the network ...

  • Page 190

    Okilan 8200e network user’s guide 190 3. Register the ip address of the network card and the host name in the /etc/hosts file. Example for ip address 172.168.20.127 and host name printer 172.168.20.127printer 4. Use the ping command to confirm connection with the network card. Example for host name ...

  • Page 191: Hp-Ux 10.X Configuration

    Okilan 8200e network user’s guide 191 e. Activate the print queue. # /usr/sbin/accept printer_lp f. Enable the print queue # /bin/enable printer_lp hp-ux 10.X configuration check the ip address, subnet mask and gateway if an incorrect ip address, subnet mask or gateway is entered, the network may go...

  • Page 192

    Okilan 8200e network user’s guide 192 if you do not have superuser rights, the network manager should conduct the configuration. 2. Register the ip address of the network card and the host name in the /etc/hosts file. Example for ip address 172.168.20.127 and host name printer 172.168.20.127 printer...

  • Page 193: Aix 4.1.5 Configuration

    Okilan 8200e network user’s guide 193 d. Register the remote printer. # /usr/sbin/lpadmin -pprinter_lp -v /dev/null -mrmodel \-ormprinter -orplp -ocmrcmodel -osmrsmodel -ob3 e. Activate the print queue. # /usr/sbin/accept printer_lp f. Enable the print queue. # /bin/enable printer_lp g. Enable the p...

  • Page 194

    Okilan 8200e network user’s guide 194 example for ip address 172.168.29.127 and host name okiprinter 172.168.20.127 printer 3. Use the ping command to confirm connection with the network card. Example for host name okiprinter # ping printer if there is no reply, there is a problem with the configura...

  • Page 195

    Okilan 8200e network user’s guide 195 example direct output port lp with print queue printer_lp and print server printer queue to be added“printer_lp” host name of the remote server“printer” queue name of the remote server“lp” type of print spooler of the remote server“bsd” description of printer na...

  • Page 196: Printing From Unix:

    Okilan 8200e network user’s guide 196 printing from unix: lpd and ftp lpd (line printer daemon) printing lpd is the most common protocol for printing with tcp/ip to a network printer. Refer to the workstation’s manual for details of the lpr and lp commands. The following explanation uses: • print fi...

  • Page 197: Printer Status

    Okilan 8200e network user’s guide 197 printer status verify the printer status using the lpq command. • the result of lpq may not be displayed correctly depending on the unix operating system specification. • while the short format of lpq is a unix-compatible format, the long format is unique to the...

  • Page 198: Logical Directories

    Okilan 8200e network user’s guide 198 ftp (file transfer protocol) printing ftp is used for transferring a file with tcp/ip. If the print data is sent to a logical printer via ftp, it is printed. Refer to the workstation’s manual for details of the ftp command. The following explanation uses: • prin...

  • Page 199: Note

    Okilan 8200e network user’s guide 199 name (cprinter:root) : root 331 password required. Password: 230 user logged in ftp> 2. Move to the preferable logical directory using the cd command. Example moving to the lp directory and confirming the current directory. Ftp> cd /lp 250 command ok. Ftp> pwd 2...

  • Page 200: Viewing Status

    Okilan 8200e network user’s guide 200 ftp> type using binary mode to transfer files. Ftp> 4. Transfer the print data to the network card using the put command. Two methods of file transfer using the put command are available, as shown in the examples below. Example method 1 transferring print data t...

  • Page 201

    Okilan 8200e network user’s guide 201 user logged in: root transfer type: binary data connection: closed. 211 end of status. Ftp> example displaying the network card status (directory name: lp). Ftp> quote stat /lp 211-ftp directory status: ready 211 end of status ftp>.

  • Page 202

    Okilan 8200e network user’s guide 202 section 7: printing using macintosh the print server supports the apple ® macintosh ® appletalk ® environment. This section consists of the following: 䊳 overview (page 203) 䊳 self-diagnostic test printout (page 204) 䊳 installing the driver (page 205) 䊳 setting u...

  • Page 203: Printing From Macintosh:

    Okilan 8200e network user’s guide 203 printing from macintosh: overview the print server supports the apple ® macintosh ® appletalk ® environment. This guide is for administrators and it should be read in conjunction with the relevant macintosh manual. The latest macintosh service packs should be in...

  • Page 204: Printing From Macintosh:

    Okilan 8200e network user’s guide 204 printing from macintosh: self-diagnostic test printout the printer server’s self-diagnostic test reports the printer’s mac address (ethernet address), required for macintosh configuration. 1. Turn the printer on. 2. Press the print server test button for more th...

  • Page 205: Printing From Macintosh:

    Okilan 8200e network user’s guide 205 printing from macintosh: installing the driver mac os 9.1+ 1. Place the drivers cd, supplied with your printer, in the cd-rom drive. 2. Double-click the icon that appears on the desktop. 3. Open the [mac] folder. 4. Open the [driver installer] folder. 5. Open th...

  • Page 206: Mac Os 10.2X

    Okilan 8200e network user’s guide 206 11. Click [quit]. Mac os 10.2x 1. Place the drivers cd, supplied with your printer, in the cd-rom drive. 2. Double-click the icon that appears on the desktop. 3. Open the [mac] folder. 4. Open the [driver installer] folder. 5. Open the folder for your language. ...

  • Page 207: Printing From Macintosh:

    Okilan 8200e network user’s guide 207 printing from macintosh: setting up the printer os 9.1+ create the desktop printer. 1. Activate chooser from the apple menu. 2. Select your model/appletalk and highlight the printer name (print server id#). Os 10.1 and above in mac os 10 you use the print center...

  • Page 208: Section 8: Troubleshooting

    Okilan 8200e network user’s guide 208 section 8: troubleshooting 䊳 self-diagnostic test (page 209) 䊳 tcp/ip (page 210) 䊳 novell netware (page 211) 䊳 ethertalk (page 213) 䊳 netbeui (page 214) 䊳 security (page 215) important! The network addresses used in this manual are shown for example only. Networ...

  • Page 209: Troubleshooting:

    Okilan 8200e network user’s guide 209 troubleshooting: self-diagnostic test printer does not print. Ensure the printer emulation is set to ps (if available) or automatic. Ng is printed in the self-diagnostic test. • confirm that the nic is installed correctly and turn the printer off and on again. •...

  • Page 210: Troubleshooting:

    Okilan 8200e network user’s guide 210 troubleshooting: tcp/ip printer cannot find the network interface card. • turn the printer off and on again. • confirm that the network interface is enabled on the printer. • make sure there is a response to the interface card command. • make sure the network ca...

  • Page 211: Troubleshooting:

    Okilan 8200e network user’s guide 211 troubleshooting: novell netware printer cannot find the network print server. • turn the printer off and on again. • confirm that the network interface is enabled on the printer. • make sure the network cable is correctly connected. • change the cable and try ag...

  • Page 212: Printer Does Not Print.

    Okilan 8200e network user’s guide 212 • make sure the machine name is the same as the print server name set in the file server. Printer does not print. • make sure the network cable is correctly connected. • change the cable and try again. • turn the printer off and on again. • make sure the nic is ...

  • Page 213: Troubleshooting:

    Okilan 8200e network user’s guide 213 troubleshooting: ethertalk not identified by the chooser and the setup utility. • turn the printer off and on again. • make sure the network cable is correctly connected. • change the cable and try again. • if the network resides in a zone, make sure the correct...

  • Page 214: Troubleshooting:

    Okilan 8200e network user’s guide 214 troubleshooting: netbeui the network interface card is not identified. • turn the printer off and on again. • make sure the network cable is correctly connected. • change the cable and try again. • make sure that [microsoft network client] and [netbeui] have bee...

  • Page 215: Troubleshooting:

    Okilan 8200e network user’s guide 215 troubleshooting: security connection error in web browser try connecting the printer using http://. Problem solution if the printer setup page appears: the certificate was not created. Log in as an administrator, then click [security] → [cipher (ssl/tls]. If the...

  • Page 216

    Okilan 8200e network user’s guide 216 if the printer setup page does not appear: the browser version is old. Make sure you are using either • internet explorer 5.5 or higher open the browser, then select [about internet explorer] in the [help] menu or • netscape navigator version 6 or higher open th...

  • Page 217: Cannot Print

    Okilan 8200e network user’s guide 217 cannot print try connecting the printer using http://. Problem solution if the printer setup page appears: the certificate was not created. Log in as an administrator, then click [security] → [cipher (ssl/tls]. If the “encryption of configuration and print” wind...

  • Page 218

    Okilan 8200e network user’s guide 218 if the printer setup page does not appear: ipp is not enabled. Enable ipp. See page 141. The browser version is old. Make sure you are using either • internet explorer 5.5 or higher open the browser, then select [about internet explorer] in the [help] menu or • ...

  • Page 219

    Okilan 8200e network user’s guide 219 the browser you are using does not support the selected key exchange method. • switch to a browser that supports the key exchange method (e.G., internet explorer 5.5 or higher, netscape navigator 6.2 or higher). • delete the current certificate and recreate it w...

  • Page 220: Important!

    Okilan 8200e network user’s guide 220 cannot install the ca certificate important! • do not change any settings for the print server during the ca certificate process (from creating the csr to installing the certificate). Any changes invalidate the issued certificate and may result in additional cha...

  • Page 221: Appendix: The Printer Menu

    Okilan 8200e network user’s guide 221 appendix: the printer menu menu basics top level functions the top-level functions menus are: 䊳 configuration (refer to appendix b in the user’s guide) 䊳 print information (refer to appendix b in the user’s guide) 䊳 print secure job (refer to appendix b in the u...

  • Page 222: Printer Menu

    Okilan 8200e network user’s guide 222 printer menu overview the following tables summarize the admin setup, calibration, print statistics and boot menu trees. The remainder of the menus above are described in appendix b of the on-line printer user’s guide. Table conventions used • the menu trees are...

  • Page 223: Admin Setup

    Okilan 8200e network user’s guide 223 admin setup c96_functions_menu_b.Jpg submenu 1 submenu 2 password (see page 233) – network setup (see page 234) slot1:100/10 base tcp/ip netbeui netware ethertalk frame type ip address set ip address subnet mask gateway address factory defaults web telnet ftp sn...

  • Page 224

    Okilan 8200e network user’s guide 224 print setup (see page 236) personality copies duplex binding job offset output bin finisher setup media check transparency detect resolution toner save mode mono-print speed default orientation form length edit size x dimension y dimension ps setup (see page 239...

  • Page 225

    Okilan 8200e network user’s guide 225 ibm ppr setup (see page 243) character pitch font condense character set symbol set letter o style zero character line pitch white page skip cr function lf function line length form length tof position left margin fit to letter text height cont paper mode epson ...

  • Page 226

    Okilan 8200e network user’s guide 226 flash memory setup (see page 249) initialize resize ps area hdd setup (see page 250) initialize resize partition format partition system setup (see page 251) near life led change password new password verify password settings (see page 253) reset settings save s...

  • Page 227: Calibration

    Okilan 8200e network user’s guide 227 calibration c96_functions_menu_b.Jpg function submenu 1 submenu 2 calibration (see page 254) auto density mode – adjust density – adjust registration – print tuning pattern – cyan tuning highlight mid-tone dark magenta tuning highlight mid-tone dark yellow tunin...

  • Page 228: Print Statistics

    Okilan 8200e network user’s guide 228 print statistics c96_functions_menu_b.Jpg function submenu 1 submenu 2 print statistics (see page 256) statistics log –.

  • Page 229: Boot Menu Tree

    Okilan 8200e network user’s guide 229 boot menu tree c96_boot_menu.Jpg category item parallel setup (see page 257) parallel bi-direction ecp ack width ack busy timing i-prime offline receive usb setup (see page 258) usb speed soft reset offline receive serial number storage setup (see page 259) chec...

  • Page 230: Printer Menu

    Okilan 8200e network user’s guide 230 printer menu making changes in the menu making changes in the function menu c96_readytoprint.Jpg 1. Ensure that the ldc dispaly panel indicates that the printer is ready to print. 2. Press enter to switch to the menu mode. C96_functions_menu_a.Jpg 3. Press the u...

  • Page 231: Example: Enabling Ftp

    Okilan 8200e network user’s guide 231 example: enabling ftp 1. Ensure that the lcd display panel indicates that the printer is ready to print. 2. Press the enter button to switch to the menu mode. 3. With [configuration] highlighted, press the enter button to select this menu. 4. Press the up-arrow ...

  • Page 232

    Okilan 8200e network user’s guide 232 making changes in the boot menu 1. Turn the printer off. 2. Press and hold the enter button while turning the printer back on: be sure to keep pressing the enter button until [initializing] appears on the display . C96_boot_menu.Jpg 3. Use the up-arrow or down-a...

  • Page 233: Printer Menu

    Okilan 8200e network user’s guide 233 printer menu functions list admin setup password item value description enter password nnnn enter a password to enter the administrator menu. The default password is 0000 (four zeroes)..

  • Page 234: Network Setup

    Okilan 8200e network user’s guide 234 network setup slot1:100/10 base item value description tcp/ip enable disable enables/disables the tcp/ip protocol. Netbeui enable disable enables/disables the netbeui protocol. Netware enable disable enables/disables the netware protocol. Ethertalk enable disabl...

  • Page 235: Slot2:wireless

    Okilan 8200e network user’s guide 235 slot2:wireless appears in the network setup menu only if the optional wireless network card is installed. See the documentation supplied with the wireless card for more information on menu settings for this option. Ftp enable disable enables/disables ftp (tcp/ip...

  • Page 236: Print Setup

    Okilan 8200e network user’s guide 236 print setup item value description personality auto postscript pcl ibm ppr epson fx hp-gl2 selects a printer language. Copies 1 ~ 999 sets number of copies. Disabled for local print, except for demo data. Duplex on off specifies duplex printing. Binding longedge...

  • Page 237

    Okilan 8200e network user’s guide 237 resolution 600dpi 600x1200dpi 600dpi multi-level sets the resolution. Toner save mode on off sets toner saving mode. Mono-print speed auto color speed normal speed sets the monochrome print speed. Auto: prints at most appropriate speed for page. Color speed: alw...

  • Page 238

    Okilan 8200e network user’s guide 238 edit size cassette size letter short edge letter long edge executive legal 14 legal 13.5 legal 13 tabloid extra, tabloid a3 nobi a3 wide a3 a4 short edge a4 long edge a5 a6 b4 b5 short edge b5 long edge custom com-9 envelope com-10 envelope monarch envelope dl e...

  • Page 239: Ps Setup

    Okilan 8200e network user’s guide 239 ps setup item value description network protocol ascii raw specifies ps transmission protocol for network data. It does not appear for non- ps type. Parallel protocol ascii raw specifies ps transmission protocol for centronics data. It does not appear for non-ps...

  • Page 240: Pcl Setup

    Okilan 8200e network user’s guide 240 pcl setup item value description font source resident dimmo downloaded specifies the location of the pcl default font. Dimm0: displayed only when font dimm rom specially prepared fonts are in the slot. Downloaded: displayed when software font is downloaded to ra...

  • Page 241

    Okilan 8200e network user’s guide 241 symbol set pc-8, pc-8 dan/nor pc-8, tk, pc-775, pc-850, pc-852, c-855, pc-857 tk, pc-858, pc-864l/a, pc-866, pc-869, pc-1004, pi font, plska mazvia, ps math, ps text, roman- 8, roman-9, roman ext, serbo croat1, serbo croat2, spanish ukrainian, vn int'l, vn math,...

  • Page 242

    Okilan 8200e network user’s guide 242 pen width adjust on off the thinnest line width in pcl, a 1- dot line, may look broken. On: when the thinnest line width is specified, line width is emphasized to look wider. Off: the line appears as specified. Tray id# – tray2 – tray3 – tray4 – tray5 1 ~ 5 ~ 59...

  • Page 243: Ibm Ppr Setup

    Okilan 8200e network user’s guide 243 ibm ppr setup item value description character pitch 10cpi 12cpi 17cpi 20cpi proportional sets the character pitch. Font condense 12 to 20cpi 12 to 12cpi sets the 12cpi pitch for condensed printing mode. Character set set-2 set-1 sets the character set to be use...

  • Page 244

    Okilan 8200e network user’s guide 244 white page skip off on sets whether a blank sheet is ejected. Cr function cr cr+lf sets the action when the cr code is received. Lf function lf lf+cr sets the action when the lf code is received. Line length 80 column 136 column sets the number of characters per...

  • Page 245: Epson Fx Setup

    Okilan 8200e network user’s guide 245 epson fx setup item value description character pitch 10cpi 12cpi 17cpi 20cpi proportional sets the character pitch. Character set set-2 set-1 sets the character set to be used. Symbol set ibm-437, ibm-850, ibm-860, ibm-863, ibm-865, pc set1, pc ext us, pc ext d...

  • Page 246

    Okilan 8200e network user’s guide 246 cr function cr cr+lf sets the action when the cr code is received. Line length 80 column 136 column sets the number of characters per line. Form length 11 inch 11.7 inch 12 inch sets the paper length. Tof position 0.0 inch 0.1 ~ 1.0 inch sets the print position ...

  • Page 247: Color Setup

    Okilan 8200e network user’s guide 247 color setup item value description ink simulation off swop euroscale japan simulates a standard printing color by the printer. The function is valid only for jobs using ps languages. Ucr low medium high sets toner layer thickness. (medium or low may help reduce ...

  • Page 248: Memory Setup

    Okilan 8200e network user’s guide 248 memory setup item value description receive buffer size auto 0.5 mb 1 mb 2 mb 4 mb 8 mb 16 mb 32 mb sets the size of the receive buffer. Resource save auto off 0.5 mb 1 mb 2 mb 4 mb 8 mb 16 mb 32 mb sets the size of the resource saving area..

  • Page 249: Flash Memory Setup

    Okilan 8200e network user’s guide 249 flash memory setup item value description initialize execute initializes resident flash memory. Resize ps area nn% [n.N mb] 30% [1.1megabyte] sets the size of the ps area in resident flash memory..

  • Page 250: Hdd Setup

    Okilan 8200e network user’s guide 250 hdd setup item submenu item value description initialize execute initializes the hdd to the factory default state. Resize partition pcl common ps nn% mm% ll% sets partition size. Format partition pcl common ps – sets the format of a specified partition..

  • Page 251: System Setup

    Okilan 8200e network user’s guide 251 system setup item value description near life led enable disable enables the attention led to be turned on when a warning for near life of a toner, a drum, a fuser, or a belt occurs..

  • Page 252: Change Password

    Okilan 8200e network user’s guide 252 change password item value description new password nnnn sets a new password to enter admin setup. Verify password nnnn lets a user verify the new password to be used to enter admin setup..

  • Page 253: Settings

    Okilan 8200e network user’s guide 253 settings item value description reset settings execute resets eeprom of the cu. Returns a user’s menu setup to the factory default state. Save settings execute saves the current menu settings..

  • Page 254: Calibration Menu

    Okilan 8200e network user’s guide 254 calibration menu item value or submenu item value description auto density mode on off – sets whether density adjustment and trc compensation is automatically performed. On: density adjustment is automatically run under the printer specified conditions and refle...

  • Page 255

    Okilan 8200e network user’s guide 255 cyan tuning magenta tuning yellow tuning black tuning highlight 0 +1 +2 +3 -3 -2 -1 adjusts highlight (light area) of cyan, magenta, yellow, or black trc. Plus indicates adjustment towards darker and minus towards lighter. Mid-tone 0 +1 +2 +3 -3 -2 -1 adjusts mi...

  • Page 256: Print Statistics Menu

    Okilan 8200e network user’s guide 256 print statistics menu item value description password entry nnnn enter password. The default password is 0000 (four zeroes). When there is no support for the print statistics function, print statistics is not displayed. Statistics log enable disable enables/disa...

  • Page 257: Printer Menu

    Okilan 8200e network user’s guide 257 printer menu boot menu to access the boot menu: 1. Turn the printer off. 2. Press and hold the enter key while turning the printer back on: be sure to continue holding the enter key until “initializing” appears on the display. Parallel setup item value descripti...

  • Page 258: Usb Setup

    Okilan 8200e network user’s guide 258 usb setup item value description usb enable disable enables/disables the usb interface. Speed 480mbps 12mbps sets the maximum usb interface transfer speed. Soft reset enable disable enables/disables the soft reset command. Offline receive enable disable when thi...

  • Page 259: Storage Setup

    Okilan 8200e network user’s guide 259 storage setup item value description check file system off hdd resolves any mismatch between actual memory and displayed memory available in a file system and performs administration data (fat information) recovery. Performs these by file system. This function t...

  • Page 260: Power Setup

    Okilan 8200e network user’s guide 260 power setup item value description peak power control normal low the fuser of the printer has two lamps. When the lamps turn on, the printer’s power draw increases dramatically. Normal: both lamps light at the same time. When this happens, the printer’s power dr...

  • Page 261: Index

    Okilan 8200e network user’s guide 261 index a admin setup menu 233-253 adminmanager quick setup 16-18 standard setup 25-59 ca certificate applying for 149, 151 installing 154-156 environmental setup netware tab 57 tcp/ip tab 56 timeout tab 59 installing 26-27 interface 28-59 ipp encryption 137-143 o...

  • Page 262

    Okilan 8200e network user’s guide 262 tree 223-228 g gateway adminmanager 32 windows printing 165-166 general tab, setup menu 30 h help menu 59 hp-ux 10.X 191-193 i ibm ppr setup menu 243-244 ip address adminmanager 31 windows printing 165-166 ip filter, adminmanager 48 ipp windows 2000 171 windows ...

  • Page 263

    Okilan 8200e network user’s guide 263 windows 2000 171 windows xp 168 port, configurable items 87-94 power minimizing power drain 260 print setup menu 236-238 printer asset number 119 reset 119 serial number 119 printer menu making changes 230-232 printer menus 221 making changes 230-232 printer tra...

  • Page 264

    Okilan 8200e network user’s guide 264 os 4.X.X 187-189 solaris 60-62 solaris 2.X 189-191 syscontact 37 syslocation 37 sysname 37 t tcp/ip configurable items 71 printing from windows 161-174 tab, environmental 56 tab, setup menu 31 troubleshooting 210 telnet configuration 60-69 hierarchical structure...