Protherm 100 Manual for instruction and use - page 2
2
3
Dear Client,
You have just become an owner of a KLO /
KLO EKO (Grizzly) natural gas or propa-
ne gas fired cast iron boiler. We are con-
fident that you will be satisfied with the
service this boiler will give you. Howe-
ver, you’ll have to comply with at least
minimum requirements when running
the equipment. Therefore please read
these Operating Instructions carefully
and comply with their guidelines.
Please pay careful attention to the following
important information:
1. The boiler with all its accessories must
be installed and used in accordance
with an installation design, all applicable
legal regulations, technical standards
and manufacturer’s instructions.
2. The boiler may be installed only in the
environment for which it has been de-
signed and only in a correctly ventilated
room.
3. After installation, the boiler must be put
into operation by a service organisation
authorised by the manufacturer.
4. Please also contact authorised service
if you are experiencing any problems
with the equipment – unauthorised re-
pairs may damage the boiler (as well as
the connected equipment!).
5. The service technician when putting
the boiler into operation for the fist time
must demonstrate its controls and show
you its various parts and how to control
them.
6. Check whether the boiler is complete.
7. Check whether it is the model you have
ordered.
8. Whenever you have any doubts how to
operate the boiler, find and study the
relevant information in these Operating
Instructions and proceed in accordance
with them.
In practice, situations might occur when the
following essential measures have to be
taken:
– prevent the boiler from being (even
accidentally) switched on while in-
specting the fumes exhaust and gas
and water distribution routes, by dis-
connecting the boiler from power
supply by another means than just
with the boiler’s switch (e.g. by pul-
ling the power cord plug out of the
socket),
– shut the boiler down every time when
flammable or explosive vapours are
present (even temporarily) inside
the premises from which combusti-
on air is supplied to the boiler,
– if it is inevitable to drain water from
the boiler or the heating system, the
water must not be dangerously hot,
– when water leaks from the boiler’s
heat exchanger or when the exchan-
ger is clogged with ice, do not try to
switch the boiler on until normal run-
ning conditions have been restored,
– during (even suspected) gas leaks or
after gas supply failure, switch the
boiler and the gas supply off and call
the gas company or authorised ser-
vice.
Regulations and Directives
The PROTHERM KLO boiler may be
put into operation only by an authorised
service organisation in accordance with
UBP SR Notice No. 74/1996. Installations,
putting the boiler into operation, warranty
and post-warranty service are performed
by a network of the manufacturer’s con-
tractual service organisations, which meet
the above-specified requirements. Instal-
lations must be carried out in accordance
with a design prepared in compliance with
applicable regulations detailed below.
9. When repairing the boiler, only original
parts must be always used. Internal wi-
ring and factory settings must not be
changed or interfered with.
10. Do not remove or damage any signs
and labels on the boiler.
11. The boiler meets regulations applicable
in Slovakia. For use in other countries,
any potential differences must be identi-
fied and resolved.
12. At the end of life of the boiler’s parts and
components (or of the entire boiler), the-
ir disposal must be carried out ecologi-
cally – metal parts must be delivered to
a metal scrap yard, plastics, seals, and
insulation materials must be sorted out
as required, or a special disposal tech-
nology used, engaging the services of
companies authorised for such operati-
ons.
13. Before a protracted shutdown we re-
commend to turn off the gas supply and
disconnect the boiler from power supply.
This recommendation is part of general
conditions defined in this Operating In-
structions.
15. The manufacturer shall not be held li-
able for any damages caused by the
user’s failure to:
– abide by the conditions defined in
these Operating Instructions,
– abide by applicable regulations and
standards,
– abide by installation and operating in-
structions.
– abide by the regulations specified in
the Warranty Certificate and Service
Book.
Such damages are not covered by the pro-
duct warranty.
a ) Heating systems:
STN 06 0310 – Central heating, design
and installations
STN 06 0830 – Safety equipment for cen-
tral heating and hot water heating sys-
tems.
STN 07 7401 – Water and steam for heat
energy equipment of operating pressure
up to 8 MPa
b ) Gas distribution systems:
STN 38 6420 – Industrial gas pipelines.
STN EN 1775 – Gas supply – Gas pipe-
lines in buildings – Maximum operating
pressure below 5 bar
STN 38 6413 – Steel gas pipelines and
connections
STN 07 0703 – Gas-fired boilers
STN 38 6405 – Gas equipment. Operating
principles.
Act No. 222/94 Coll. on business condi-
tions and public service supervision in
the energy industry and on state energy
inspection.
c ) Electrical installation:
STN 33 2180 – Wiring of electrical instru-
ments and appliances.
STN 33 2000-3 – Electrical installation in
buildings. Part 3: Definition of basic char-
acteristics.
STN 33 2000-7-701 – Electrical installa-
tion in buildings. Part 7: Requirements on
special installations or premises. Section
701. Rooms with a bath-tub…
STN 33 2130 – Electrical engineering reg-
ulations. Interior electrical installations.
STN 33 0160 – Electrical engineering
regulations. Labelling terminals of electri-
cal objects.
Execution regulations.
STN 33 0165 – Electrical engineering
regulations. Colour marking or numbering
of wires.
Execution regulations.
STN 33 2350 – Regulations for electrical
equipment in difficult climatic conditions.