Sentrol ZX400 Installation Manual - page 27
27
•
ZXODM: Output Driver Module: Provides ten
(10) fully programmable 40 mA + 12 VDC out-
puts. Nominal current drain: 10 - 13 mA with
no outputs connected.
•
ZXPTR Printer Interface Module: Allows connec-
tion of a standard parallel printer via interface.
Nominal current drain: 45 - 55 mA without
printer connected.
•
ZX410 - ZX400 Control board mounted in
EX1414 enclosure. (The ZX410 assembly is re-
quired for Burglary applications).
•
ZX440F - ZX400 Control board mounted in
EX1414F enclosure with ZXCFM Fire Module.
(The ZX440F assembly is required for Commer-
cial Fire applications).
•
F2600 Transformer Enclosure: Ensures that the
AC plug-in transformer remains securely fixed
to the AC wall outlet. (Required for Commercial
Fire applications).
•
T-1635 Transformer: UL Listed Class II plug-in
16.5 VAC 35 VA secondary.
•
T-1620 Optional Transformer: UL Listed Class II
plug-in 16.5 VAC 20 VA secondary.
•
T1850 Transformer: UL Listed Class II plug-in
18 VAC 50 VA secondary.
•
HCP-12SULC Power Supply: Provides a 12 or
24 VDC power-limited output with a current
rating of 2.0 A continuous while the AC primary
power source is present.
•
CR860 Dual Battery Harness: Allows for an ad-
ditional 12 VDC 7 Ah sealed lead acid battery
connection to the control to meet additional
standby requirements.
•
CR862 Battery Harness: Allows for 12 VDC 17.2
Ah sealed lead acid battery connection to the
control to meet additional standby requirements.
•
EB1511 Auxiliary Enclosure: 15" x 11" x 4" en-
closure with cam lock allows wall mounting of
accessories and batteries.
•
EX1414 Optional Larger Enclosure: 14" x 14" x
3.5".
•
EX1414F Larger Red Enclosure for Fire: 14" x 14"
x 3.5".
•
AE912 Raucous Sounder: Current consumption:
28 mA @ 12 VDC.
•
MPI-266 Battery Cut-Off Module: Disconnects
battery from deep discharges.
•
MPI-267 Power Disconnect Module: Discon-
nects battery from deep discharges.
•
MPI-268 Earth Ground Fault Detector: Current
consumption: less than 20 mA.
•
MPI-206 General Purpose Relay Module.
SPECIFICATIONS AND FEATURES
•
4710 RF Gateway (8 RF Zone Devices, 6 RF User
Devices). Nominal Current Drain: 80mA.
•
4720 RF Gateway (16 RF Zone Devices, 12 RF
User Devices). Nominal Current Drain: 80mA.
•
4110 Universal Transmitter and battery.
•
4545 Shatter Pro Glassbreak Detector with Trans-
mitter and batteries.
•
4655 Sharpshooter PIR with Transmitter and
battery.
•
4004 Four Button Wireless Key Transmitter and
Battery.
•
4310S, ST, SLT Wireless Smoke Detectors (UL
217) with Transmitter and Battery.
•
4330S, ST, SLT, SLTM Wireless Smoke Detectors
(UL 268) with Transmitter and Battery.
•
4113 Three Point Universal Transmitter and Bat-
tery.
•
4010 Single Button Panic Transmitter and Battery.
•
4011 Dual Button Panic/Medical Transmitter and
Battery.
•
ZEM Fire Zone Expansion Modules:
2502-ZEM Two Class B Zones
2504-ZEM Four Class B Zones
Current Drain: 40 - 60 mA.
Max. Line Resistance: 100 Ohms (Class B)
•
ZRM Zone Relay Modules:
ZRM-2 (2 Zones)
ZRM-4 (4 Zones)
Contact Rating: 5 A @ 12 VDC, 120 VAC resistive.
•
ZXIRR01 Security System Remote Control with
Keyfob Transmitter.
•
ZXLCDD1 LCD Keypad Demonstrator. (Demo
Unit Only).
•
ZXVFDD1 VFD Keypad Demonstrator. (Demo Unit
Only).
•
TC1100 Tamper Enclosure
•
ZXCVR-Red Tamper Enclosure with two 3025T
Tamper Switches
Output Provisions
•
Low Current Trigger Outputs: Current output
of 40 mA each. One output on main board, ex-
pandable to 21 with ZXODM Output Driver
Modules and/or ZXEXP Zone Expander Module.
•
Maximum combined continuous current drain
at Terminals 4, 5, 6, 10, and PG01 is 0.9 amps
with 16.5 VAC 35 VA transformer.
•
Current Limits: The combined current at Bell
Output Terminal 5 is limited to 1.85 amps
(PTC2). The 12V Auxiliary current is limited by
PTC4 to 1.35 amps. Reverse battery protection
is limited to 1.85 amps (PTC3).