VADDIO AutoTrak 2.0 Installation And User Manual - Short Term Confidential
AutoTrak 2.0 Camera Tracking System
©2012 Vaddio - All Rights Reserved. AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. A
Page 11 of 47
7 Software
Control
8 Not
Used
4) GPIO Port: The GPIO Port provides the ability to interface with external control systems. Inputs are logic
level low. Output is an open collector.
Pin
Function
1
Power (12Vdc)
2
Mute (Input)
3
Mute Status (Output)
4
Volume Up (Input)
5
Volume Down (Output)
6
Not Used
7
Ground
5) USB Type B Connector: This connector is used to interface with the Host PC for Skype type applications.
6) Audio Outputs: There are two (2) Audio Outputs on the rear panel:
Balanced Audio Output Jack:
Balanced Line Level (on XLR - M connector) +4dBu
Unbalanced Audio Output Jack:
Unbalanced Line Level (on RCA-F connector)-10dbV
Lanyard, Belt Pack Controls:
The central medallion of the lanyard has an attached, strain-relieved, 32” cable that
terminates to a 5-pin mini XLR female connector. Attach the 5-pin mini XLR to the 5-pin
mini XLR male connector on the belt pack. The microphone element is on the top of the
central medallion. The lanyard material houses a flat flex type circuit where the IR LEDs
are mounted. After the initial setup is complete, the presenter should slip the lanyard over
their head and position the medallion away from the presenter and face the Vaddio logos
on the lanyard cloth cover out, toward the cameras. Clip the belt pack onto the clothing,
belt or waistband securely. Please avoid dropping the belt pack.
Power to illuminate the IR LEDs is supplied from the Belt Pack and if the System Power
Switch is ON, the IR LEDs will illuminate at 850 nanometers (out of the range of visible
light for humans). Each Lanyard has 15 IR LEDs spread out evenly throughout the
Lanyard Necklace. This invisible light is picked up by the IR reference camera of the
AutoTrak 2.0 System and information is sent to the Tracking Camera in order to follow the
presenter throughout the presentation environment.
Installation and Operating Instructions
for AutoTrak 2.0 with Belt Pack Unit and IR Lanyard
999-7250-000 and 999-7260-000 North America
999-7250-001 and 999-7260-001 International
1) Connect the 12 VDC, 1.0 Amp power supply to the Audio Interface.
2) Connect the 6.5” RP-SMA Antenna to the back of the Audio Interface.
3) Connect the Audio outputs to a mixer/amp.
4) Select a frequency to transmit and receive audio from the Belt Pack Unit on the back of the Audio Interface.
5) Touch the Power button on the Audio Interface and the blue LED inside the power switch will illuminate
6) Turn the Audio Level on the front panel to “1”.
7) Connect the Lanyard to the Belt Pack
8) Move the System Power and the Microphone switches on the Belt Pack to the “OFF” position
9) Remove the battery door on the Belt Pack:
a. Set the 3-position dip switch to the same frequency (position) as the Audio Interface
b. Carefully matching the polarity markings; install four (4) AA batteries (not included)
c. Return the battery door cover
10) Move the System Power and the Microphone power switch on the Belt Pack to the “ON” position.
11) The System Status LED on the Audio Interface should illuminate.
12) Make sure that the Mic Mute LED on the front panel is not lit.
13) Adjust the mic volume by moving the Audio Level potentiometer until the desired output level is reached.
Central
Medallion
32”Cable to
Belt Pack
Mic
Element
24”
Lanyard
Necklace
Do not fold the Lanyard Necklace at any time as it contains a
flexible circuit that may cease to work if the necklace is hard
folded. Folding the Lanyard Flex Circuit will void any and all
warranties.
GPIO Port Pin Configuration