VADDIO AutoTrak 2.0 Installation And User Manual - Short Term Confidential
AutoTrak 2.0 Camera Tracking System
©2012 Vaddio - All Rights Reserved. AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. A
Page 8 of 47
4) Dip
Switches:
There are two (2) 4-position dip switches located on the circuit board, SW4 and SW5. They
provide configuration settings for Microphone Gain Control, Filtering, Compression and Microphone Filtering
and Pairing of the Wireless Belt Pack to the AutoTrak 2.0 Wireless Audio Interface.
5)
Procedure for Belt Pack Pairing with the AutoTrack 2.0 Wireless Audio Interface:
Note: If the AutoTrak 2.0 System and the Optional AutoTrak 2.0 Wireless Audio Interface are ordered
at the same time for delivery, the Belt Pack will be paired with the AutoTrak 2.0 Wireless Audio
Interface at the factory.
Pairing Procedure:
1) Place the Belt Pack in close proximity to the AutoTrak 2.0 Wireless Audio Interface.
2) Remove the Battery Compartment Cover:
To open: Carefully pry the top of the Removable
Battery Cover at the small opening.
3) Locate Pairing Button Switch labeled SW2:
Press the button and release. The Radio LED on
the Belt Pack should begin blinking at a slow rate.
4) Press the Pair Button on the front panel of the EasyTalk AutoTrak 2.0 Wireless Audio
Interface:
Important Note: The button on the AutoTrak 2.0 Wireless Audio Interface must be pushed
within ten (10) seconds of pressing the pairing button SW2 on the Belt Pack or pairing will
not
occur.
5) The Belt Pack and the AutoTrak 2.0 Wireless Audio Interface will automatically sync with
each other:
The blue LED’s on the Belt Pack and the AutoTrak 2.0 Wireless Interface will turn solid
blue indicating they are paired.
Switch
Number
Function
1
Enable/Disable Bandpass Audio
Filter
2
Enable/Disable IR Transmitter in
Lanyard
3
Enable/Disable Radio in BPU
4
Not Used
Optional Belt Pack Configuration Settings:
Note: The Belt Pack has a number of custom settings that can be enabled or disabled for specific
application needs. These settings can be applied by activating dip switch settings on the two (2) 4-
position dip switches SW4 and SW5 located on the Belt Pack Circuit Board.
SW4: Dip Switch 1/ Bandpass Filter:
Enable adds a Bandpass Filter to the microphone to emphasize a
brighter sound for speech. Disable turns it off.
SW4: Dip Switch 2/ IR Transmitter:
Enable turns on the IR Transmitter LED’s in the IR Lanyard.
Disable turns off the IR Transmitters in the Lanyard and the camera tracking will not function.
SW4: Dip Switch 3/ Radio in Belt Pack:
Enable turns on the Radio circuit in the Belt Pack. Disable will
turn off the Radio circuit-which will extend the battery life of the Belt Pack if you are not using the
optional EasyTalk AutoTrak 2.0 Wireless Audio Interface with the AutoTrak 2.0 System.
SW4: Dip Switch 4/ Not Used:
Note: The following Gain Boost Switches 1-3 can be used individually or in combination. Ex: If Dip
Switch 1/ 3dB Gain and Dip Switch 2/ 6dB Gain are enabled, they will add a total of 9 dB of gain.
SW5: Dip Switch 1/ 3-dB Gain Boost:
Enable adds a three (3) dB gain to the microphone audio.
Disable provides zero gain.
SW5: Dip Switch 2/ 6-dB Gain Boost:
Enable adds a six (6) dB gain to the microphone audio. Disable
provides zero gain.
SW5: Dip Switch 3/ 9-dB Gain Boost:
Enable adds a nine (9) dB gain to the microphone audio.
Disable provides zero gain.
Switch
Number
Function
1
3dB Gain Boost on Microphone
2
6dB Gain Boost on Microphone
3
9dB Gain Boost on Microphone
4
Automatic Gain Control Mode
SW 4: Dip Switch Settings
SW 5: Dip Switch Settings
Belt Pack Dip Switch Settings: