VADDIO AutoTrak 2.0 Installation And User Manual - Short Term Confidential
AutoTrak 2.0 Camera Tracking System
©2012 Vaddio - All Rights Reserved. AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. A
Page 5 of 47
One (1) 37mm to 58mm adapter ring
One (1) 58mm polarizing filter
One (1) 58mm band-pass IR filter
One (1) AutoTrak 2.0 Quick-Connect Box (998-1105-020)
One (1) Standard Quick-Connect Box (998-1105-001)
One (1) 24VDC, 2A, 50/60Hz 110-240V Switching Power Supply (451-2000-0024)
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) 18”/45.8cm Video Cable (BNC to RCA)
One (1) 12”/30.48cm Cat 5e Patch Cable
One (1) 998-2100-000 - Vaddio IR Remote & Manual (2-AAA batteries not included)
One (1) **535-2000-233 Stacked Gusseted Mount for two (2) HD-18 and Mounting Hardware
Three (3) 998-1001-232 Control Adapters
One (1) 998-7200-232 Control Adapter for use with the AutoPresenter - (Only needed when used with the AutoPresenter
for Tracking Camera PTZ Presets)
Documentation and Manuals (Document Number (342-0382)
For the 999-7260-001 System -
Startwith the 999-7250-001System
Remove:
One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Add:
One (1) *HD-20 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
*Note 1:
The Vaddio HD-18 and HD-20 cameras are preloaded with AutoTrak 2.0 control protocols which differ from
the “VISCA” type control normally used in the stock HD-18 PTZ Camera. The HD-18 cameras will work with the
Vaddio IR Remote but is recommended that the PTZ positions of the camera be set with the AutoTrak 2.0 Software.
The HD-18 AutoTrak 2.0 cameras will not work with any other controller besides AutoTrak 2.0 at this time.
**Note 2:
The stacked camera arrangement is required for the AutoTrak 2.0 software to track properly.
AutoTrak 2.0 Components:
AutoTrak 2.0 CPU
Note: The AutoTrak 2.0 CPU may be subject to change in cosmetics due to the turbulent nature of the
PC industry, parts availability and model year upgrades. If changes are made, Vaddio will be certain to
make changes in the documentation accordingly. The AutoTrak 2.0 CPU is a 1-RU rack mount computer
that will come preloaded with the AutoTrak 2.0 software. The exact specifications are subject to change
and any changes that will be made will be in the spirit of product improvement only. The AutoTrak 2.0
CPU uses an Intel® Atom™ Dual Core Processor, Intel Graphics Media Accelerator, 1GB DDR2 Memory,
four (4) RS-232 Ports, six (6) USB 2.0 ports, two (2) PS/2 interfaces for keyboard/mouse, 16GB Compact
Flash and Video capture card.
An important feature: After the AutoTrak 2.0 CPU and software is configured using the mouse, keyboard
and monitor, these I/O devices can be removed to prevent any unauthorized access to the system. To
reattach the mouse and keyboard, the system will need to be rebooted to recognize these devices.
Front Panel Controls of AutoTrak 2.0 Worldwide CPU:
1) Power
Indicator:
Illuminates when power in on
2) Hard Drive Activity Indicator:
Indicates when hard drive is active
3) Recessed Reset Switch:
Resets the system without removing power to the CPU
4) USB Ports:
Two (2) Front Panel USB Ports
① ② ③
④