- DL manuals
- WoodPro
- Wood stove
- WS-TS-1500
- Owner's Manual
WoodPro WS-TS-1500 Owner's Manual
Summary of WS-TS-1500
Page 1
Www.Woodprostoves.Com 1-877-427-3316 ws-ts-1500 ws-ts-2000 ws-ts-2500 www.Woodprostoves.Com www.Woodprostoves.Com 4085-112 rev: a.
Page 2
1. The installation of this stove must comply with your local building code rulings. Please observe the clear- ances to combustibles (see reference ſiwtgu 4–8). Do not place fuel, furniture or any other objects within the clearance area. 2. Verify that the stove is properly assembled and installed b...
Page 3
Safety instructions ...Continued woodpro™ / page 3 18. During the ſrst 12 to 15 ſres the special paints and pro- tective oils used in construction of your stove may give off some smoke and odor while they are curing. This should disappear after a short period of time and not occur again. Persons wit...
Page 4
Table of contents page 4 woodpro™ table of contents ..................................................................................... 4 safety instructions ............................................................................. 1 – 3 assembly instructions .....................................
Page 5
Locating the stove page 5 woodpro™ 1. The stove must be placed on solid concrete, solid masonry, or when installed on a combustible ƀqqr, on an underwriters laboratories listed type 2 ƀoor protector listed to ul standard ul 1618, such as hy-c or imperial model ul4056bk. Floor protector must be 1/2 Ŋ...
Page 6
6 minimum clearances for installation according to ul 1482 (us) & ulc-s 627 (can) a.
Page 7
7 top a a alcove.
Page 8
Philips blower attachment 8 (4 places) a gasket.
Page 9
9 ws-ts-2500 23 8 6.
Page 10
10 6.
Page 11
Connector pipe sizing connector pipe is used to make the connection from the ſpcn positioning of your stove to an approved chimney. Connector pipe is not kpenwfgf as part of the stove. Connector pipe must be 6”/152mm diameter minimum of 24 msg (minimum standard gauge) b ncck or 26 msg b nwguvggnuvov...
Page 13
Masonry chimney the chimney must be a code-approved, masonry chimney with ƀwg liner. Before using an existing ma- sonry chimney, clean the chimney, inspect the ƀue liner and make any repairs needed to be sure it is safe to use. Make repairs before attaching the stove. The connector stove pipe and ſv...
Page 14
Figure 12 - chimney construction through roof figure 13 - chimney connection to firebox through masonry wall manufactured chimney refer to chimney and chimney connec- tor maker’s instructions for installation and use. Use only Ŋoo fkcogvgt ocnufcevwtgf ejko- ney sys veo lisved vo ul 03 ht (us) ot ul...
Page 15
Vkſgf chimngy swggp, or a knoyngfigcbng kpurgevqr. Consult your insur cpeg eqorcny if you ecppqv ſpf a swcnkſgf gzrgrt. Caution: not all fireplace chimneys are suitable for conversionto accom- modate connection to a wood stove. Check with a qualified expert. Many pr gfabrieatgf ſrgplaegs arg of thg ...
Page 16
A. Brick masonry minimum Ŋoo thick brick masonry all framed into combustible wall with a minimum of 1 Ŋ305mm brick separation from clay liner to combustibles. The ſtgenay liner shall run from outer surface of brick wall to, but not beyond, the inner surface of chimney ƀwg liner and shall dgſrmly cem...
Page 17
This stove is designed to burn wood fuel only! Hardwood, Ŋ to Ŋ / 45cm to 50cm should be air dried (seasoned), for a minimum of 6 months. Logs grater than 6 Ŋ/152mm in diameter should be split.Wood should be stored in a dry, well ventilated area. The humidity content for usable ſtewood must be less ...
Page 18
Height, weather, log size, wood species and moisture content. Some experimentation will initially be required to ſnd that “sweet spot” where your stove performs best. The following will give you a starting point to ſpf your optimum settings. When ſrst loading fuel set the primary air inlet con- trol...
Page 19
7. Once fuel has been loaded, close the door and leave the air inlet control fully open until ſtg is well established (at least 15–20 minutes) being careful not to over ſtg (if any of the exterior parts of the stove or chimney connections begin to glow you are ov gtſring the stove). 8. Re-adjust the...
Page 20
20
Page 21
21.
Page 22
Warning: replace glass only with 4mm high temperature ceramic glass of the proper size. Do not use substitute materials such as tempered glass or double thickness window glass! Contact the stove manufacturer for replacement glass. Gasket and glass cleaning products are available at local retail home...
Page 23
23 baffle removal.
Page 24
24 baffle removal.
Page 25
Service parts 25.
Page 26
Service parts 26.
Page 27
Service parts 27.
Page 28
Service parts 28.
Page 29
Service parts 29.
Page 30
Service parts ws-ts-2500 30
Page 31
Blower maintenance the optional blower is maintenance free other than cleaning. Lightly vacuum motor and air inlet to keep free of dust and dirt. Notice: any replace- ment wiring must have e q u i va l e n t i n s u l a - tion and temperature rating (105°c). Caution: moving parts can cause injury. D...
Page 32
This stove has been tested for and must be installed on a ƀqqt protector with the proper thermal resistance or r-value as stated in step 1 of the installation instructions under “locating stove” section of this manual. If the ƀqqt protector ma- terials listed in the instructions are not available, m...
Page 33
Date of service performed by description chimney & stove maintenance log 33.
Page 34
Warranty woodpro secondary tubes, ba ŋĞ͕gaskets wood firebo dž͕Ňue collar, front door,ash door 3 34.
Page 35
Warranty 35.
Page 36
36 www.Woodprostoves.Com 2.