WoodPro WS-TS-1500 Owner's Manual - page 11
CONNECTOR PIPE SIZING
Connector pipe is used to make the connection
from the
ſPCN positioning of your stove to an approved
chimney. Connector pipe is NOT
KPENWFGF as part of
the stove. Connector pipe must be 6”/152mm diameter
minimum of 24 MSG (minimum standard gauge) b
NCck
or 26 MSG b
NWGUVGGNUVove pipe.
NOTICE: FOR MOBILE HOME INSTALLATIONS
(US ONLY), CONNECTOR PIPE MUST BE
DOUBLE-WALL, HIGH-TEMPURATURE PIPE
THAT MEETS UL 103 HT SPECIFICATIONS.
Any connector pipe used must be in good condition.
Rep
Nace if necessary before using stove. Connector
pipe is not rated to provide c
Nose contact to combustibNe
mater
KCNU and must have proper ENGCrance from com-
bustib
NG materKCNU as shown in the ENGCrance diagrams
on the previous pages. Connector pipe shou
Nd never be
used in p
Nace of a chimney. If proper cNGCrances are not
observ
GFCJQWUGſTGEQWNFTGUWNV
INSTALLATION INSTRUCTIONS
Please Note: Insta
NNation of a ƀue damper is NOT
recommended. Combustion contro
N is reguNated by the
intake of combustion air, not the exhaust.
1.
The crimped end of the stovepipe
ſVU inside the
stove
ƀue coNNar. Secure with three (3) equaNNy
spaced sheet meta
N screws. The ſrst section of
connector pipe must be
UKPING wCNNGF to properN[
attach to the stove c
QNNar. InstaNN additioPCN pipe and
e
Nbow with the crimped end towards the stove.This
YKNN CNNow any condensation in the ƀWG to run back
KPVQVJGſTGDox.
2.
Hor izonta
N pipe runs must sNope upwards
towards the chimney at
NGCUV ŊOO per foot
of horiz
QPVCNrun.
3.
You must have at
NGCUV ŊOO of ENGCrance
between any horiz
QPVCNRKRKPICPFVJGEGKNKPI
4.
The pipe cannot extend into the chimney f
Nue
ſIWTG
5.
Secure a
NN pipe/eNbow sections with three (3) equaNNy
spaced sheet
OGVCN screws at each joint to make
the piping rigid. DO NOT CONNECT THIS STOVE
TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
6.
It is recommended that no more than two (2)
90° bends be used in the stovepipe insta
NNa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possib
Ny
cause smoke
URKNNCIe. Where possibNe, use QPN[
corrugated (non adjustab
Ne) eNbows. These
pro
XKFGCDGVVGTUGCN
The connector pipe must not pass through an
attic or roof space, trusses, c
Noset, or any conceaNed
space,
ƀQQr, EGKNKPI wCNN or combustibNG construc-
tion. (See Chimney Connector Systems &
%NGCT-
ances, page
A manufactured chimney system
NKUVGF to UL 103 HT (US)/ULC-S629 (CAN) must
be used from the
ſTUV penetration of EGKNKPI or wCNN
to the chimney cap.
Where passage through a w
CNN or partition of com-
bustib
Ne construction is desired, the instaNNation shaNN
conform to Chimney manufacturer’s instructions.
WARNING: DO NOT USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.
)LJXUHă6tovepipe/Flue Connections
NOTE: CONNECTOR PIPE IS NOT INCLUDED.
TO PURCHASE, VISIT YOUR LOCAL HARD-
WAR E , H O M E , O R BU I L D I N G C E N T E R .
ADDITIONAL SPECIFICATIONS.
11