Xpresskit DBALL Installation Manual - Remote
Rev.: 20160610
Platform: DBALL/DBALL2
Firmware:
CHRYSLER7
© 2016 Directed. All rights reserved.
Page 4
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
(+) Parking Lights Output
(+) Brake Input
(-) E-Brake Status Input
10
RF
LED
4
TX
(-) Ground
RX
(+)12V
14
12
2
Immo. Data (conn. side): Yellow: 8
Immo. Data (veh. side): Orange/Yellow: 9
Ignition Output: Yellow/Red: 11
(+) 12V: Brown/Red: 12
(+) Brake Output: Gray: 6
Immo. Data (veh. side): Yellow/Black: 10
(-) RAP Off: Orange/Black: 11
(+) PTS Output: Gray/Black: 7
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(-) (AC) Tach Output: Violet/White: 5
P#: XKD2D65
(+) 12V
(+) Brake:
Dk. Green/Lt. Green,
pin 1
(-) Ground
(-) Ground
(MUX) Parking Lights Output: Violet/Brown: 9
(MUX) Parking Lights:
White/Brown,
pin 3
Not required in D2D mode.
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
7: Pink/White: (+) Parking Light Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
Black 6-pin conn.
(located at PTS switch)
6
5
4
3
2
1
Immo. Data:
White/Lt. Green
,
pin 5
White 4-pin conn.
(located at brake switch)
(+)
P
T
S
:
V
iolet/Brown
,
pin 4
(+) Ignition Input
(+) Starter
(-) Ground: Black: 14
(-) Ground
(+) 12V: Red: 13
(+) 12V
Black 6-pin Conn.
(located at headlamp switch)
1
2
3
4
5
6
1
2
3
4
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
(+) 12V: Red, pin 16
Harness
in driver kick panel
(-) Driver Door
Trigger: Violet
(+) 12V: Red, pin A
Gray C1 conn.
(located at BCM
under driver dash)
B
A
Installation without T-Harness
1
8
16
9
HS CAN High:
Gray/White, pin 6
HS CAN2 High: Gray, pin 3
[2]
HS CAN Low: Yellow, pin 14
HS CAN2 Low: White, pin 11
[2]
OBDII
Diagnostic Connector
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[2]
HS CAN2 Low: Orange/Brown: 6
[2]
HS CAN2 High: Orange/Green: 5
[2]
DBALL2 Only. Required for heated seats.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Prog. Button
DBALL/
DBALL2
Black 6-pin conn.
(located at PTS switch)
LED
Status
Description
Troubleshooting
Off
Module has no power.
Check the power connections.
Solid red
Start of programming is normal
If the LED is red after the ignition is ON, check for CAN-High
and CAN-Low connections as the ignition is not seen on
CAN.
Flashes green fast
Normal. CAN programmed and waiting for
bypass programming.
Normal operation
Flashes orange
slowly
Normal. Waiting for offline key2go
programming.
Solid green for 3
seconds with a quick
orange flash.
Module successfully programmed or is
already programmed.
Normal operation
Solid green for 3
seconds.
Module successfully programmed.
Normal operation
Module programming - Error codes
Flashes red x2
CAN not detected.
Check the Tan - Tan/Black wire connections. Wake up the
data bus by turning the ignition on and try again.
Flashes red x3
Bypass data not detected.
Check the bypass line connection, make sure there is a
continuity between the 2 sides of the cut and turn the ignition
ON. Make sure the battery was removed when turning the
ignition ON.
External Module Synchronisation
Flashes red, red,
then orange x 10
OBDII feature not supported.
Diagnostic data bus not detected. Some features are not
supported by SmartStart. This can be caused by missing
wire connections or module hardware limitation. Refer to
the wiring installation section to check the connections.
Active Ground While Running
Flashes green
GROUND OUT ON (GWR) command
received.
Otherwise, the Ground While Running (status) signal
was lost or was never received by the module.
Commands can come from RF, D2D or W2W.
Flashes red &
orange
IGNITION ON command received.
Otherwise, the ignition signal was not received by the
module. In a W2W install, it will show only if the ignition
input wire is used.
Flashes green
quickly
START ON command received.
Otherwise, the start signal was not received by the
module. In a W2W install, it will show only if the ignition
input wire is used.
D2D and W2W Commands
Flashes orange x 1
LOCK command received.
Flashes orange x 2
UNLOCK command received.
Flashes orange x 3
TRUNK command received.
Module programming - Firmware specific
Commands can come from RF, D2D or W2W.
Solid
OFF
Flashes
Flashes
Solid and
quick flash
Solid
Flashes
red x2
Flashes
red x3
Flashes
red, red,
orange x10
Flashes
green
Flashes
green
Flashes
orange x1
Flashes
orange x1
Flashes
orange x1
Flashes
orange x1
Flashes
orange x2
Flashes
orange x3
Flashes red
& orange