Bakers Pride BCO-G Operation Manual - Installation Instructions
GAS CONVECTION OVEN OPERATION MANUAL
2
INSTALLATION INSTRUCTIONS
For a stack of two ovens: Refer to Figure 3
(1) Remove flue from bottom oven prior to stacking.
When top oven is properly positioned on bottom
oven, re-install the flue back on the bottom oven.
(2) Tilt lower unit over to the left side and position two
6” legs on the right side (one for front and one for
back), secure in place by using 4 bolts (3/8”-16)
per leg. Tighten firmly.
(3) Using proper lifting equipment, lift up the left side
of the unit and attach the other two legs in the
same way.
(4) Using the lifting equipment, raise the top oven to
proper height and slide on top of the bottom oven.
Line up sides and front and fasten to each other at
the rear of the units by using a mounting bracket
supplied in the stacking kit.
To assemble an open rack stand: Refer to Figure 1
(1) Loosen 12 bolts (attaching 31” legs) slightly.
(2) Remove 4 inner bolts, 1 from each of the 4 legs,
place top right angle and top left angle underneath
and tighten these 4 bolts.
(3) Insert “Open Rack Shelf” and tighten into place
with eight 3/8-16 screws, washers and nuts.
(4) Position “Rack Supports” and tighten in place using
4 each of flat washers and 5/16-18 Hex Nuts.
Fit the Standard Flue Diverter supplied into the hole in
the top of the oven for under ventilation hood installation
and secure with screws. For direct venting, Flue
Adapter and Draft Hood must be placed into the hole on
top of the oven.
Installation With Casters (Optional): Refer To Figure 4
Four casters (two with wheel brakes) and the mounting
hardware are packed and included in the shipment if
ordered. Install casters with wheel brakes on the front
of the unit. Installation of the unit should be made with
a connector that complies with the latest edition of the
Standard for Connectors for Movable Gas Appliances
ANSl Z21.69 in the USA (CAN CSA-6.16 in Canada)
and a quick-disconnect device that complies with the
latest edition of the standard for quick disconnect
devices for use with gas fuel ANSl Z21.41 in the
USA (CSA 6.9 in Canada). Adequate means must be
provided to limit the movement of the appliance without
depending on the connector and any quick disconnect
device or its associated piping to limit appliance
movement.
The restraint should be attached to the rear legs of
the oven on which casters are mounted. If disconnect
of the restraint is necessary, the restraint should be
immediately reconnected after the appliance has been
returned to its originally installed position.
Do not store combustible items or materials on racks
CAUTION
Figure 1: Open Rack Stand Assembly Instructions, BCO-G & GDCO-G
Assembly Instruction
1. Place undershelf (6) between legs & secure with 1 1/4-20 UNC
screws (4), flat washers (3) & locknuts (2). The holes for mounting
the wire racks should be toward the front of the oven.
2. Place open rack supports (1) between legs & secure with
1/4-20 UNC screws (4), flat washers (3) & locknuts (2).
3. Slide wire rack supports (5) into position using the holes in the
undershelf (6) as a guide.
Item
P/N
Description
Qty
1
21818232
Support, Open Rack
2
2
770504
Lock Nut 1/4-20
12
3
8519600
Washer, Flat 1/4”
12
4
8208200
Screw, 1/4-20 x 3/4”
12
5
21816807
Support, Wire Rack
2
6
21818220
Undershelf, Gas Oven
1