Bulldog Security RS79P Installation Manual - Making Connections
7
6. Use electrical t
6. Use electrical tape to wrap. Be sure to cover the wire
ape to wrap. Be sure to cover the wire about two inches on either
about two inches on either
side of the connection. First pull
side of the connection. First pull the wire that you have just connected along
the wire that you have just connected along
side the wire you connected to, t
side the wire you connected to, tape and wire tie them together
ape and wire tie them together. Use this method
. Use this method
for all connections.
for all connections.
CAUTION:
CAUTION: All wires must be wrapped with t
All wires must be wrapped with tape and wire tied.
ape and wire tied.
2.
2. TTwist upper wires together
wist upper wires together, twist lower wires together
, twist lower wires together as shown.
as shown.
1. When tying two sep
1. When tying two separate wires together at their ends, strip back 1 of insulation
arate wires together at their ends, strip back 1 of insulation
on both wires and sep
on both wires and separate
arate the strands of wire as shown below
the strands of wire as shown below..
MAKING END
MAKING END TTO END CONNECTIONS
O END CONNECTIONS
MAKING CONNECTIONS
Wire
Wire TTie
ie
Electrical
Electrical TTape
ape
4. Insert the wire(s) from the st
4. Insert the wire(s) from the starter through the hole as shown. If
arter through the hole as shown. If two or more wires are inserted,
two or more wires are inserted,
wrap them in opposite directions.
wrap them in opposite directions.
5.
5. W
Wrap the wire around one side then the other and finally around i
rap the wire around one side then the other and finally around ittself as shown.
self as shown.
1
1
2
2
3
3
Use this method ONL
Use this method ONLY
Y when connecting two sep
when connecting two separate wires end to end.
arate wires end to end.
Manufacturer
Manufacturer
Make/
Make/ Y
Year
ear
Anti-thef
Anti-theftt
Acura
TL 99+
TRANSPONDER
CL 98+
TRANSPONDER
RL 99+
TRANSPONDER
INTEGRA 00 +
TRANSPONDER
NSX
TRANSPONDER
AUDI
A4 00+
TRANSPONDER
A6 00+
TRANSPONDER
A8 98+
TRANSPONDER
BMW
ALL 97+
TRANSPONDER
BUICK
CENTURY 97+
VATS
LESABRE 90-96, 2000
VATS
PARK AVE 91-96
VATS
PARK AVE 97+
TRANSPONDER
REGAL 93-96
VATS (Some)
RIVIERA 93-99
VATS (Some)
ROADMASTER 93-96
VATS
SKYLARK 96-98
PASSLOCK 1
CADILLAC
ALLANTE 91-93
VATS
BROUGHAM 90-96
VATS
CATERA 98+
TRANSPONDER
DEVILLE 92-96
VATS
DEVILLE 99+
TRANSPONDER
ELDORADO 89-98
VATS
ELDORADO 99+
VATS
ESCALADE 99+
PASSLOCK 2
FLEETWOOD 90-96
VATS
SEVILLE 90-98
VATS
SEVILLE 99+
TRANSPONDER
SLS/ STS 97+
TRANSPONDER
CHEVROLET
ASTRO 98+
PASSLOCK 2
BLAZER 98+
PASSLOCK 2
CAMARO 86+
VATS
CAVALIER 95-99
PASSLOCK 1
CAVALIER 2000+
PASSLOCK 2
CORVETTE 88+
VATS
EXPRESS 98+
PASSLOCK 2
IMPALA 2000+
PASSLOCK 2
LUMINA 96+
VATS
VÉHICULES AVEC SYSTÈME
ANTIDÉMARRAGE DE LUSINE
38
3. Sep
3. Separate the vehicle wire(s) as shown. Make the sep
arate the vehicle wire(s) as shown. Make the separation large enough to fit the other
aration large enough to fit the other
wire through.
wire through.
2. S
2. Strip back one inch of insulation on the wire you need to connect
trip back one inch of insulation on the wire you need to connect to.
to.
One Inch of Bare Wire
One Inch of Bare Wire