Bulldog Security RS79P Installation Manual - Contact De
11
(Parking Light Output continued)
If the circuit is (+) positive and pulls less than 10 amps, connect the
BROWN
wire from
the 9-pin harness directly to the vehicles parking light wire. If the circuit is negative,
you must use a relay if not hooking to the BCM or the vehicles computer. Part #775
is required for most negative parking light circuits.
Connect the
BROWN
wire from the 9-pin harness to the vehicles parking light circuit
if you are not using a relay.
BRAKE INPUT
BRAKE INPUT (BLUE WITH BLACK STRIPE)
(BLUE WITH BLACK STRIPE)
The brake wire is located on the switch near and above the brake pedal, if you cannot
locate this wire at the brake switch, you will then need to locate a wire at the rear window
brake light or at the brake light system in the rear of the vehicle. The correct wire will
show +12V only when the brake is pressed. Connect the BLUE WITH BLACK STRIPE
BLUE WITH BLACK STRIPE
from the 9-pin harness to this wire.
ANTENNA
ANTENNA (YELLOW)
(YELLOW)
For best results, run the antenna (YELLOW WITH BLACK
YELLOW WITH BLACK TIP
TIP in the 9-pin harness)
as straight as possible. Do not place the antenna next to any met
Do not place the antenna next to any metal p
al part
arts or the vehicle
s or the vehicless
main computer control.
main computer control.
FFACT
ACTOR
ORY
Y ALARM SHUT
ALARM SHUT DOWN WIRE (F
DOWN WIRE (FASD) (-) (RED WITH BLACK STRIPE)
ASD) (-) (RED WITH BLACK STRIPE)
If your vehicle is equipped with a factory alarm system (as most vehicles with
a factory keyless entry are) or, if your vehicle DOES NOT have a factory remote
control that honks the horn when locking and unlocking the doors, or when
you use the key in the drivers door, you DO NOT get a light on the dash that
says security then mostly you will not need to use this wire. If your vehicle
is so equipped, probe for a small gauge wire (usually found in the drivers side
kick panel) that shows (-) ground when the door lock cylinder is turned to the
unlock position using the key. This wire will usually show a (+) positive voltage
before turning the key. NOTE
NOTE: Some factory disarm wires remain neutral before
you turn the key to unlock instead of +12v positive. Connect the RED WITH
RED WITH
BLACK STRIPE
BLACK STRIPE wire from the 9-pin harness to this wire.
HOOD PIN SWITCH (BLACK WITH BLUE STRIPE)
HOOD PIN SWITCH (BLACK WITH BLUE STRIPE)
This feature will keep the engine from starting, or shut off the engine when in
remote start mode only. The hood pin switch has no control over the engine
when started with the ignition key or under normal operation. Locate a good
chassis ground, if at all possible do not install the pin switch in the rain gutter.
Drill a 5/16 hole, insert the pin switch into the hole and tighten. Check for the
hood adjustment, there is approximately 1/4 adjustment in the pin switch.
Close the hood easy, making sure that the pin switch is not keeping the hood
from closing all the way, if it does, cut off approximately 1/8 of the black plastic
off of the top of the hoodpin switch and try closing the hood again. Check to
make sure that the hoodpin switch remains neutral when the hood is closed
and shows ground when the hood is open. Plug the BLACK WITH BLUE
BLACK WITH BLUE
STRIPE
STRIPE wire from the 9-pin harness into the bottom of the hood pin switch.
TTACH INPUT
ACH INPUT (BLACK WITH WHITE STRIPE)
(BLACK WITH WHITE STRIPE) (Optional)
By this time, you should have determined the way you want your vehicle to
start (tach or tachless). Tachless uses voltage electronic signals and timing to
work. Tach types use a signal directly from the ignition coil. If you have chosen
the TACHLESS start option, simply proceed to the next step and skip the
following instructions. Make sure you tape this wire up if not used. For TACH
mode connect the BLACK WITH WHITE STRIPE
BLACK WITH WHITE STRIPE wire from the 9-pin harness
to the negative side of the coil or the tach wire at the coil pack under the hood.
To find the coil pack follow the spark plug wires back to their beginning point.
To operate in tach mode, make sure to program tach option. See programming
tach option page 15.
AUXILIAR
AUXILIARY
Y INPUT
INPUT (BLUE) (For
(BLUE) (For Af
Aftermarket
termarket Alarms)
Alarms)
If you use this starter with an aftermarket alarm, connect the BLUE
BLUE wire from
the 9-pin harness to the second or third channel output of your existing alarm.
When the output is activated, a signal will activate the remote starter.
NOTE:
This wire will also be used if you wish to connect the unit up to operate
off of your Factory Keyless Entry. See Programming to Start Your Vehicle
from your Factory Keyless Entry, page 15. (Extra part #775 relay is required.
See diagram, page 12.)
LOCATING & MAKING CONNECTIONS
CONTACT MÉCANIQUE DE SÉCURITÉ DE POINT MORT
Quand vous installez une télécommande de démarrage Bulldog dans un
véhicule GM ou un Dodge Dakota fabriqué avant 1996, vous devez :
Utilisez le schéma ci-dessous pour créer un circuit qui empêche la
télécommande de démarrage de mettre le moteur en marche, sauf si la
clé est retirée du commutateur dallumage.
GM À PROPULSION ARRIÈRE, AVANT 1996,
AVEC FIL VIOLET DE LANCEMENT
Relais n
o
775 en option requis
CONTACT DE
SÉCURITÉ DE POINT MORT
Masse
Masse
86
30
87a
87
85
Fusible
5 A
À relier au gros
fil blanc du
faisceau à
quatre relais
Fil de contact de
capot négatif (-)
Afficheur multi-
message ou
tonalité de clé
Contact de porte contucteur
Barillet de clé
HANANE
HANANE
VER
VERT
T
NOIR
NOIR
JAUNE
JAUNE
BLEU
BLEU
BLANC
BLANC
NE P
NE PAS UTILISER LE FIL
AS UTILISER LE FIL ROUGE; L
ROUGE; LISOLER
ISOLER
ROUGE
ROUGE
FUSIBLE
DODGE DAKOTA AVANT 1996
Relais n
o
775 en option requis
Masse
NOIR/
NOIR/
BLEU CLAIR
BLEU CLAIR
Masse
86
30
87a
87
85
CLAIR
CLAIR
BLEU/VER
BLEU/VERT
T
NOIR
NOIR
JAUNE
JAUNE
BLEU
BLEU
BLANC
BLANC
ROUGE
ROUGE
Fusible
5 A
À relier au gros
fil blanc du
faisceau à
quatre relais
Fil de contact de
capot négatif (-)
NE P
NE PAS UTILISER LE FIL
AS UTILISER LE FIL ROUGE; L
ROUGE; LISOLER
ISOLER
FUSIBLE
Afficheur multi-
message ou
tonalité de clé
Contact de porte contucteur
Barillet de clé
34