9031344-02 smartswitch 9000 9c500 plus power box installation guide.
I notice notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...
Notice ii fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...
Iii notice declaration of conformity addendum application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european representative address: ...
Notice iv.
V contents chapter 1 installing the 9c500 plus power box getting help .................................................................................................................. 1-2 installation......................................................................................................
Contents vi.
1-1 chapter 1 installing the 9c500 plus power box the 9c500 plus power box (power box) is installed in a standard 19 inch equipment rack near the smartswitch 9000 9c114 chassis (chassis) only after two power supplies (9c214-1 ac or 9c214-2 dc) have been attached directly to the chassis. Power suppli...
Installing the 9c500 plus power box 1-2 getting help for additional support related to this device or document, contact cabletron systems using one of the following methods: before calling cabletron systems, have the following information ready: • your cabletron systems service contract number • a d...
1-3 installing the 9c500 plus power box 5. Ensure the power supply wiring is routed away from sharp edges. 6. Power up the power supplies. Installing the power box complete the installation of the first power box by following the steps below: 1. Remove the unit from the shipping box. (save the shipp...
Installing the 9c500 plus power box 1-4 1. Loosen and remove the two screws from the right auxiliary power source connector cover (looking from the back of the equipment rack to the front) on the rear of the chassis. 2. Remove the connector cover. (keep the cover in the event you need to remove the ...
1-5 installing the 9c500 plus power box figure 1-1. Connecting auxiliary power cord attaching terminator if you are connecting only one power box to a chassis, the unused auxiliary power source connector on the rear of the chassis must be terminated. To complete the termination, use the terminator i...
Installing the 9c500 plus power box 1-6 installing power supplies two power supplies (either two 9c214-1 ac, or two 9c214-2 dc; but not one of each) can be installed in a power box. The power supplies installed in the power box must be identical to those attached to the back of the smartswitch 9000 ...
1-7 installing the 9c500 plus power box figure 1-2. Installing power supply (supplies) powering up power supplies if necessary, before performing the power up steps, refer to the smartswitch 9000 9c214-1 ac power supply installation guide or the smartswitch 9000 9c214-2 dc power supply installation ...
Installing the 9c500 plus power box 1-8 2. Check that the leds for smb (system management bus) and pwr (power) are green. If the leds are any color other than green, refer to the smartswitch 9000 9c214-1 ac power supply installation guide or the smartswitch 9000 9c214-2 dc power supply installation ...
1-9 installing the 9c500 plus power box operating specifications safety specifications this equipment meets: the safety requirements of: • ul 1950 • csa c22.2 no. 950 • en 60950 • iec 950 the emi requirements of: • fcc part 15 class a • en 55022 class a • vcci class i the immunity requirements of: •...
Installing the 9c500 plus power box 1-10 plus power box dimensions 22.22 h x 48.3 w x 56.52 d centimeters (8.75 h x 19.0 w x 25.25 d inches) weight unit: 5.40 kilograms (12 pounds) shipping: 6.75 kilograms (15 pounds).
