1. DL manuals
  2. Cabletron Systems
  3. Wireless Router
  4. SmartSwitch 9000
  5. User Manual

Cabletron Systems SmartSwitch 9000 User Manual

Manual is about: switching module with twenty-six 100 Mbps Ethernet ports

Summary of SmartSwitch 9000

  • Page 1

    9032531-01 smartswitch 9000 9m426-02 user’s guide.

  • Page 3: Notice

    I notice notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...

  • Page 4: Fcc Notice

    Notice ii fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...

  • Page 5

    Iii notice declaration of conformity addendum application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european representative address: ...

  • Page 6

    Notice iv.

  • Page 7: Contents

    V contents chapter 1 introduction features........................................................................................................................... 1-1 related manuals............................................................................................................ 1-4 ge...

  • Page 8

    Contents vi.

  • Page 9: Chapter 1

    1-1 chapter 1 introduction the 9m426-02 smartswitch module shown in figure 1-1, is a three port switch module with two front panel hsim interfaces and one inb-2 backplane interface. With the proper hsim, this module may be used as an atm uplink for the smartswitch 9000 chassis. Features processor th...

  • Page 10

    Introduction 1-2 connectivity the 9m426-02 module has one interface to the inb-2 and two front panel hsim interfaces. Management information base (mib) support for a complete list of supported mibs, refer to the release notes provided in the 9m426-02 package. Lanview leds the 9m426-02 uses lanview –...

  • Page 11

    1-3 introduction figure 1-1. The 9m426-02 module smb cpu inb 9m426-02.

  • Page 12: Related Manuals

    Introduction 1-4 related manuals the manuals listed below should be used to supplement the procedures and technical data contained in this manual. Smartswitch 9000 installation guide smartswitch 9000 9c300-1 environmental module user’s guide smartswitch 9000 9c214-1 ac power supply user’s guide inb ...

  • Page 13: Chapter 2

    2-1 chapter 2 installing the smartswitch 9000 module this module uses hsims for the front panel connections. They are not shipped with the module and must be purchased separately. For installation information, refer to the manual supplied with the hsim. Unpacking the module 1. Carefully remove the m...

  • Page 14

    Installing the smartswitch 9000 module 2-2 figure 2-1. User accessible components smb-1 prom flash simm socket local dram socket i960 processor dip switch 1 2 3 4 5 6 7 8 boot prom.

  • Page 15

    2-3 installing the smartswitch 9000 module an eight position dip switch is located on the module card as shown in figure 2-1. The function of the switches are listed in table 2-1. See the cautions at the end of this table. Table 2-1. Function of dip switch switch function description 8 clear passwor...

  • Page 16: Chassis

    Installing the smartswitch 9000 module 2-4 installing the module into the smartswitch 9000 chassis to install the smartswitch 9000 module, follow the steps below: 1. Remove the blank panel covering the two slots in which the module is being installed. All other slots must be covered, if other module...

  • Page 17

    2-5 installing the smartswitch 9000 module figure 2-2. Installing the 9m426-02 module 7 f l n k 8 f l n k f l n k 10 f l n k ins 11 f l n k ins 12 rx tx rx tx rx circuit card card guides metal back-panel jack for esd wrist strap warning: ensure that the circuit card is between the card guides. Lock ...

  • Page 18: The Reset Switch

    Installing the smartswitch 9000 module 2-6 the reset switch the reset switch is located under the top plastic tab as shown in figure 2-3. Use the reset switch to reset the module’s processor, shutdown (power down) the module, and/or restart the module. • to reset the module’s i960 processor, press t...

  • Page 19: Chapter 3

    3-1 chapter 3 operation the 9m426-02 fddi smartswitch module is a three port switch module with two front panel hsim interfaces and one inb-2 backplane interface. This module, with the proper hsim, may be used for an fddi, atm, wan and other high-speed connectivity for the smartswitch 9000 chassis. ...

  • Page 20: System Diagnostic Controller

    Operation 3-2 band from user data. Modules which share the smb-10 bus periodically send out loop-back packets to ensure the validity of smb-10. In the event a fault is detected on the smb-10, the smb-1 can be used as an alternate communication channel by the modules. System diagnostic controller thi...

  • Page 21: I960 Core

    3-3 operation between the host processor, the inb backplane, and lan/wan interfaces on the front panel of smartswitch 9000 modules. The smartswitch asic can operate in two modes: as a traditional switch, or as a securefast switch (sfs). When operating in traditional switch mode, it makes filtering/f...

  • Page 22

    Operation 3-4.

  • Page 23: Chapter 4

    4-1 chapter 4 lanview leds the front panel lanview leds indicate the status of the module and may be used as an aid in troubleshooting. Shown in figure 4-1 is the lanview leds of the 9m426-02 module. Figure 4-1. The lanview leds 9 9m m4 42 26 6--0 02 2 s sm mb b c cp pu u iin nb b system status fnb ...

  • Page 24

    Lanview leds 4-2 the functions of the two system status leds, system management bus (smb) and the cpu, are listed in table 4-1. The functions of the inb receive led are listed in table 4-2. The functions of the inb transmit led are listed in table 4-3. Table 4-1. System status (smb and cpu) leds led...

  • Page 25: Chapter 5

    5-1 chapter 5 specifications technical specifications cpu intel i960 risc based microprocessor memory 4 meg. Flash memory (expandable to 8 meg.) 16 meg. Dram (expandable to 32 meg.) network interface cabletron hsims safety this equipment meets the safety requirements of: • ul 1950 • csa c22.2 no. 95...

  • Page 26

    Specifications 5-2 • emc requirements of: en 50082-1 iec 801-2 esd iec 801-3 radiated susceptibility iec 801-4 eft service mtbf (mhbk-217e) >200,000 hrs. Mttr physical dimensions 35.0 d x 44.0 h x 6.0 w centimeters (13.8 d x 17.4 h x 2.4 w inches) weight unit: 2.6 kg. (6lb) shipping: 3.6 kg. (8lb) e...