Federal Signal Corporation AR2000-M Installation And Maintenance Manual - page 16
-15-
5 seconds with the power “ON”.
B.RecordingaMessageforBroadcast.
When the line attached to the Router is called,
theRouterwillanswerwiththemessage“ENTER
PASSWORD”.Enteryour8digitpassword.
Thenthecallerwillhearthemessage“PRESS
9KEYTOCHANGETHEPASSWORDOR6KEYTO
RECORDAMESSAGE”.
Pressthe6key,themessage“RECORD
MESSAGE,PRESS#KEYTOBROADCASTYOUR
MESSAGE”promptsthecallertostartspeaking.Say
yourmessageintothephone.Press[#]andhangupthe
phone.Yourmessagewillbesenttoallzonesconnected
totheAudioRouterDevice.Themessagecanbeupto
90 seconds long. If the user exceeds 90 second duration,
themessagewillnotplayback.Thisistheprocedurefor
selecting “All Call”.
C.AbortaMessageWithoutSendingit
Anywhere.
Hangupatanytimewithoutpressing[#].
D.SendYourMessagetoaSpecificSelected
Zone or Zones.
Aftersayingthemessage,pressanykeyson
thetelephonekeypadfrom1-8.Thesecorrespondto
the eight zones which are connected to the master
AR2000-Munit.Pressing[1]willselectZone1,pressing
[5]willselectZone5andpressing[8]willselectZone8.
Forexample:TosendamessagetoonlyZone3
oftheAR2000-M,afterrecordingthemessagekeyin[3]
andthenpressthe[#]key.Themessagewillbesentonly
toZone3.
Forexample:TosendamessagetoZone3and
Zone4oftheAR2000-M,afterrecordingthemessage
keyin[3],keyin[4]andthenpressthe[#]key.The
messagewillbesenttoZone3andtoZone4.
IfadditionalAR2000-Zunitsareconnected,
thoseZonesmayalsobeindividuallyselected.To
accomplishthisfirstkeyin[*],thenkeyinthebank
number which is associated with the additional zones you
desiretoreference(2–8)andthenkeyinaZoneforthat
bank.Amaximumofseven(7)additionalZoneBanks
maybeaddedtotheAR2000-Mdevice.Themasterunit
isdesignatedasBank1.
Forexample:Keyingin[*],[1],[2]willselectto
sendyourmessagetozone2ofBank1(locatedinthe
masterunit).The[*]saysyouareabouttoselectaBank
numberandZone.TosendthemessagetoBank1Zones
1,4,and6,afterrecordingamessagekeyin[*],[1],[1],
[4],[6],[#]andhangup.Themessagewillbesentto
Zones1,4and6oftheMasterunit(Bank1).
Forexample:IfthereisoneAR2000-Zunit
connectedtotheAR2000-M,thenitisonBank2.To
sendamessagetoonlyZone4oftheAR2000-ZinBank
2,keyinthefollowingafterrecordingamessage:keyin
[*],[2],[4],andthenpressthe[#]keyandhangup.The
messagewillbesentonlytoZone4ofBank2.
Forexample:IftherearetwoAR2000-Zunits
connectedtotheAR2000-M,thentheyareonBank2
andonBank3.TosendamessagetoZone4ofthe
AR2000-ZinBank2andZone5oftheAR2000-Zin
Bank3,keyinthefollowingafterrecordingamessage:
keyin[*],[2],[4]andkeyin[*],[3],[5]andthenpressthe
[#]keyandhangup.ThemessagewillbesenttoZone4
ofBank2andZone5ofBank3.
Forexample:TosendamessagetoZone6from
Bank8afterrecordingamessage,keyin[*],[8],[6]and
thenpressthe[#]keyandhangup.Themessagewillbe
senttoZone6ofBank8.
Forexample:ToselectZones1,3,5fromBank
2andZones1,2fromBank3,keyinthefollowingafter
recordingamessage:keyin[*],[2],[1],[3],[5],[*],[3],[1],
[2],[#]andhangup.ThemessagewillbesenttoZones
1,3and5ofBank2andZones1and2ofBank3.
E.SendYourMessagetoaSelectedPreset.
Afterrecordingamessage,firstkeyin[0],then
theassociatedBanknumber(1-8)andthenthePreset
numberofthatBank(1-8).Thezeroindicatesyouare
abouttoselectapresetBankandpresetnumber.Only
one preset may be selected for a message.
IfadditionalAR2000-Punitsareconnected,
thosePresetsmayalsobeindividuallyselected.To
accomplishthis,firstkeyin[0],thenkeyintheBank
number which is associated with the additional Preset
youdesiretoreference(2–8)andthenkeyinaPreset
forthatbank.Amaximumofseven(7)additionalPreset
BanksmaybeaddedtotheAR2000-Mdevice.The
masterunitisdesignatedasBank1.
Toselectpreset2fromBank2afterrecordinga
message,keyin[0],[2],[2]andthenpressthe[#]keyand
hangup.ThemessagewillbesenttoPreset2ofBank2.
ToselectPreset3fromBank8afterrecordinga
message,keyin[0],[8],[3]andthenpressthe[#]keyand
hangup.ThemessagewillbesenttoPreset3ofBank8.
Telephoneoperationisessentiallyindependent
of other operations except when the device plays its
recorded message. Whatever modes were active before
phone operation will return when the phone message is
complete.Intheeventthattheunitisstuckinplayback
mode and needs to be disconnected, press and hold the