Garmin GPSMAP 4008 - Marine GPS Receiver Owner's Manual - page 48
44
GPSMAP
®
4000/5000 Series Owner’s Manual
a
ppendIx
a
ppend
Ix
NMEA Depth Is Below Transducer—(sonar) the
NMEA depth input is using the DBT sentence which
does not include keel offset.
No DGPS Position—unit lost differential GPS
reception (WAAS). Make sure you have a clear view of
the sky.
No Proximity Waypoints Found—no proximity
waypoints found while attempting a user data transfer.
No Routes Found—no routes found while attempting a
user data transfer.
No Tracks Found—no tracks found while attempting a
user data transfer.
No User Waypoints Found—no user waypoints found
while attempting a user data transfer.
Not All Maps Fit, Some Maps Will Not Be Drawn—
there are more maps present on the SD card than the
unit can support. Some maps on the card will not be
drawn or used to find map features.
Off Course Alarm—the boat has left the user-defined
course.
Please insert card—appears if you attempt to use a
feature that requires an SD card.
Proximity Alarm—the boat has come close to a user-
defined proximity point.
Proximity Alarm Memory is Full—the proximity
waypoint memory is full. Erase existing proximity
waypoints to make room.
Radar Guard Zone Alarm—(radar) an object has been
detected in the user-defined radar guard zone.
Radar Needs Repair Error Code—(radar) the radar
needs repair. An error code will be listed to help
diagnose the error.
Radar Service Incompatible. Software Update
Required—a radar software update is needed. Contact
Garmin Product Support for assistance updating your
network.
Radar Service Lost—(radar) the unit has lost
communications with the remote radar unit. Check the
network and the radar wiring.
Route Already Exists—the named route already exists.
Choose another name.
Route is Full—the individual route is full, no more
waypoints can be added.
Route Memory is Full, Can’t Create Route—the
unit’s Route memory as a whole is full, no more routes
can be created. Erase existing routes to make room.
Route Truncated—some points on the end of the route
have been discarded.
Shallow Water Alarm—(sonar) the boat has entered
the user-defined shallow water depth.
Simulating Operation—the unit is in Simulator Mode.
Sonar Failed, Unit Needs Repair—there has been a
sonar failure and the unit needs to be sent in for repair.
Contact Garmin Product Support.
Sonar Service Incompatible. Software Update
Required—a software update is needed. Contact
Garmin Product Support for assistance updating your
network.
Sonar Service Lost—(sonar) the unit has lost
communications with the remote sonar unit. Check the
network and the sonar wiring.
The position format that is selected is associated with
this map datum—map datum restriction explanation.
tide Alarm—tide has reached user-specified tide alarm
range.
track Already Exists—the named track already exists.
Choose another name.
Track Log Full—there is no longer any space in the
active track log storage.
Track Truncated—some points on the end of the track
have been discarded.
Transducer Disconnected, Sonar Turned Off—the
transducer has been disconnected. Sonar has been
turned off. Check transducer wiring.
Transfer Complete—user data transfer is complete.
Unknown bridge height within calculated auto-
guidance route—(g2 Vision) there is an unknown
bridge height within the auto-guidance route.
User Card Not Found—user data card transfer. Make
sure an SD card is fully inserted.
Water Speed Sensor not Working—the water speed
sensor is not working properly. Check the wheel for
obstructions and check wiring.
Water Temperature Alarm—(temperature sensor/
transducer) the water temperature has entered or left the
user-defined water temperature alarm zone.
Warning: Auto-guidance route starting position
moved due to safe depth settings—(g2 Vision) auto-
guidance has calculated the route, but the starting point
has been moved to deeper water.
Warning: Auto-guidance route ending
position moved due to safe depth settings
(BlueChart g2 Vision) auto-guidance has calculated the
route, but the end point has been moved to deeper water.
Waypoint Already Exists—the named waypoint
already exists. Choose another name.
Waypoint Memory is Full, Can’t Create
Waypoint—the User Waypoint memory is full. Erase
existing waypoints to make room.