1. DL manuals
  2. NEC
  3. Wireless Router
  4. SL1100
  5. Programming Manual

NEC SL1100 Programming Manual - 10-04 : Music On Hold Setup

Summary of SL1100

  • Page 1

    Programming manual a50-031167-003 na issue 4.0

  • Page 2: Copyright

    Copyright nec corporation reserves the right to change the specifications, functions, or features at any time without notice. Nec corporation has prepared this document for use by its employees and customers. The information contained herein is the property of nec corporation and shall not be reprod...

  • Page 3: Table of Contents

    Table of contents chapter 1 introduction section 1 before you start programming.......................................................... 1-1 section 2 how to use this manual........................................................................... 1-1 section 3 how to enter programming mode..........

  • Page 4

    10-54 : license configuration for each package............................................. 2-50 10-58 : network address.................................................................................. 2-51 10-60 : audio port setup ......................................................................

  • Page 5

    15-03 : single line telephone basic data setup.......................................... 2-133 15-05 : ip telephone terminal basic data setup.......................................... 2-136 15-06 : trunk access map for extensions..................................................... 2-139 15-07 : pro...

  • Page 6

    20-38 : operator group setting...................................................................... 2-216 20-42 : night mode for each package............................................................ 2-217 20-43 : power supply for each package.........................................................

  • Page 7

    22-20 : flexible ringing by caller id setup................................................... 2-277 program 23 : answer features setup..................................................................... 2-278 23-02 : call pickup groups..................................................................

  • Page 8

    32-04 : door box name setup....................................................................... 2-335 program 34 : tie line setup.................................................................................... 2-336 34-01 : e&m tie line basic setup................................................

  • Page 9

    44-07 : gain table for ars/f-route access................................................. 2-397 44-08 : time schedule for ars/f-route....................................................... 2-398 44-09 : weekly schedule for ars/f-route.................................................... 2-400 44-10 ...

  • Page 10

    82-09 : sliu codec filter data setup......................................................... 2-485 82-11 : sliu initial data setup....................................................................... 2-488 82-12 : opx initial data setup................................................................

  • Page 11

    90-35 : wizard programming level setup..................................................... 2-580 90-36 : firmware update time setting.......................................................... 2-581 90-37 : set temporary license...................................................................... 2...

  • Page 12: List of Tables

    List of tables table 1-1 keys for entering data....................................................................................... 1-3 table 1-2 keys for entering names................................................................................... 1-4 table 1-3 softkey display prompts..........

  • Page 13: Introduction

    Introduction s ection 1 before you start programming before customizing your system be sure to read this chapter first. This chapter provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this cha...

  • Page 14

    Pressed. To learn how to enter the programming mode, refer to how to enter programming mode on page 1-2 . S ection 3 how to enter programming mode to enter programming mode : 1. Go to any working display telephone. In a newly installed system, use extension (port 1). 2. Do not lift the handset. 3. P...

  • Page 15

    3. The display shows "complete data save" when completed and exits the telephone to an idle mode. To save a customer’s database, a blank compact flash (cf) card is required. Insert the cf card into the cpu and, using program 90-03, save the software to the cf card. (program 90-04 is used to reload t...

  • Page 16

    When you want to ... Telephone programming change program number soft key3 change index number move cursor to right cursor key (right) soft key4 s ection 6 programming names and text messages several programs (e.G., program 20-16 : selectable display messages) require you to enter text. Use the foll...

  • Page 17

    _ program mode hard mtnance s ection 8 what the softkey display prompts mean when using a display telephone in programming mode, various softkey options are displayed. These keys will allow you to easily select, scan, or move through the programs. Table 1-3 softkey display prompts softkey display pr...

  • Page 18

    System number plan/capacities note system type number plan/capacities related pro- gram trunk ports (total) : 76 • analog trunks 36 • t1/pri trunk ports 48 • voipdb trunk ports (voipdb & memdb is re- quired. Need license to be max.) 16 did translation tables 20 22–10 did translation table entries 80...

  • Page 19

    System number plan/capacities note system type number plan/capacities related pro- gram conference circuits 32 : maximum (16 parties per conference) department and pickup groups department (extension) group numbers 1 ~ 32 16–01 call pickup group numbers 1 ~ 32 23–02 hotline internal hotline 128 exte...

  • Page 20

    S ection 10 concept of slot number each unit installed to the system has a slot number assigned. Some of slot number are fixed to a unit that be installed. Other slots are not fixed to unit but fixed to location where it is installed. Below chart shows the slot and its number : expansion ksu 1-3 slo...

  • Page 21: Programming The Sl1100

    Programming the sl1100 s ection 1 programming your system the information contained in this chapter provides the information necessary to properly program your system. The programming blocks are organized into the following programming modes. Program number : program name program 10 : system configu...

  • Page 22

    Program number : program name program 93 : system information on page 2-619 sl1100 issue 4.0 2-2 programming the sl1100

  • Page 23: 10-01 : Time and Date

    Program 10 : system configuration setup 10-01 : time and date level: sa description use program 10-01 : time and date to change the system time and date through system programming. Extension users can also dial service code 728 to change the time if allowed by an extension class of service. Input da...

  • Page 24: 10-02 : Location Setup

    Program 10 : system configuration setup 10-02 : location setup level: sa description use program 10-02 : location setup to define the location of the installed system. Input data item no. Item input data description default 01 country code dial (up to four digits) : 0 ~ 9, * , # enter the country co...

  • Page 25: 10-03 : Etu Setup

    Program 10 : system configuration setup 10-03 : etu setup level: in description use program 10-03 : etu setup to setup and confirm the basic configuration data for each unit. When changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatical...

  • Page 26

    For coiu unit setup physical port number 1 ~ 4 item no. Item input data default 01 logical port number 1 ~ 36 0 for priu pkg setup isdn line number 01 ~ 24 item no. Item input data description default 01 isdn line mode 0 = no setting 1 = t-point 2 = s-point 6 = s-point (leased line) 1 02 logical por...

  • Page 27

    Item no. Item input data description default 14 service protocol for s-point 0 = keypad facility 1 = specified protocol for aspire sys- tem 0 15 call busy mode for s-point 0 = alerting 1 = disconnect 0 16 two b-channel transfer for pri service 0 = off 1 = on 0 18 type of number 0 = unknown 1 = inter...

  • Page 28

    Item no. Item input data description default 06 number of ports 0 = auto 1 = 4 ports 2 = 8 ports 3 = 12 ports 4 = 16 ports 5 = 20 ports 0 for voipdb pkg setup physical port number 01 ~ 32 item no. Item input data default 01 trunk logical port number 1 ~ 84 0 02 trunk type 1 = sip 1 conditions • when...

  • Page 29: 10-04 : Music On Hold Setup

    Program 10 : system configuration setup 10-04 : music on hold setup level: in description use program 10-04 : music on hold setup to set the music on hold (moh) source. For internal music on hold, the system can provide a service tone callers on hold or one of eleven synthesized selections. Input da...

  • Page 30: 10-08 : Pre-Ringing Setup

    Program 10 : system configuration setup 10-08 : pre-ringing setup level: in description use program 10-08 : pre-ringing setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk led flas...

  • Page 31

    Program 10 : system configuration setup 10-09 : dtmf and dial tone circuit setup level: in description use program 10-09 : dtmf and dial tone circuit setup to allocate the circuits on the cpu for either dtmf receiving or dial tone detection. The cpu has 16 circuits initially, and an additional 16 ci...

  • Page 32

    • central office calls, placing • direct inward dialing (did) • direct inward system access (disa) sl1100 issue 4.0 2-12 program 10 : system configuration setup program 10

  • Page 33: 10-12 : Cpu Network Setup

    Program 10 : system configuration setup 10-12 : cpu network setup level: sa description use program 10-12 : cpu network setup to setup the ip address, subnet-mask, and default gateway addresses. Caution! If any ip address or nic settings are changed, the system must be reset for the changes to take ...

  • Page 34

    Item no. Item input data description default 04 time zone 0~24 (0 = -12 hours and 24 = +12 hours) determine the offset from greenwich mean time (gmt) time. Then enter its respective value. For example, eastern time (us and canada) has a gmt offset of -5. The program data would then be 7 (0 = - 12, 1...

  • Page 36: 10-13 : In-Dhcp Server Setup

    Program 10 : system configuration setup 10-13 : in-dhcp server setup level: sa description use program 10-13 : in-dhcp server setup to setup the dhcp server built into the cpu. Input data item no. Item input data description default 01 dhcp server mode 0 = disable 1 = enable enable or disable the us...

  • Page 37

    Program 10 : system configuration setup 10-14 : managed network setup level: sa description use program 10-14 : managed network setup to set up the range of the ip address which the dhcp server leases to a client. Input data item no. Item input data description default related pro- gram 01 the range...

  • Page 38

    Program 10 : system configuration setup 10-15 : client information setup level: sa description use program 10-15 : client information setup to set up the client information when the dhcp server needs to assign a fixed ip address to clients. Input data client number 1 ~ 16 item no. Item input data de...

  • Page 39

    Program 10 : system configuration setup 10-16 : option information setup level: sa description use program 10-16 : option information setup to set up the option given from the dhcp server to each client. The items highlighted in gray are read only and cannot be changed. Input data item no. Item inpu...

  • Page 40

    Item no. Item input data description default 10 ftp server address code number 0 ~ 255 set a ftp server ad- dress used for autocon- fig. 43 (fixed) sub code number 141 ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 0.0.0.0 11 config file name code number...

  • Page 41

    Item no. Item input data description default 23 lds server 4 code number 0 ~ 255 162 (fixed) ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 0.0.0.0 24 next server ip address ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223...

  • Page 42

    Program 10 : system configuration setup 10-19 : voipdb dsp resource selection level: in description use program 10-19 : voipdb dsp resource selection to define the criteria for each dsp resource on the voipdb unit. Input data dsp resource number 01 ~ 32 item no. Item input data description default 0...

  • Page 43

    Program 10 : system configuration setup 10-20 : lan setup for external equipment level: in description use program 10-20 : lan setup for external equipment to define the tcp port/address/etc. For communicating to external equipment. Input data type of external equipment 1 = cti server 2 = acd mis (v...

  • Page 44

    Feature cross reference none sl1100 issue 4.0 2-24 program 10 : system configuration setup program 10

  • Page 45

    Program 10 : system configuration setup 10-23 : sip system interconnection setup level: sa description use program 10-23 : sip system interconnection setup to determine if the system is interconnected and define the ip address of another system, call control port number and alias address for sl1100 ...

  • Page 46

    Program 10 : system configuration setup 10-24 : daylight savings setup level: sa description use program 10-24 : daylight savings setup to set the options for daylight savings. As the telephone system is used globally, these settings define when the system should automatically adjust for daylight sa...

  • Page 47

    Program 10 : system configuration setup 10-26 : ip system operation setup level: in description use program 10-26 : ip system operation setup to enable or disable the peer to peer feature for sip mlt and sip ip stations. Input data item no. Item input data default 02 rtp forwarding mode 0 = disable ...

  • Page 48: 10-27 : Ip System Id

    Program 10 : system configuration setup 10-27 : ip system id level: in (this program is available for v1.5 or higher) description use program 10-27 : ip system id to set the ip address of the networked ip systems. Input data network system id (v4.0 added) 1 ~ 4 item no. Item input data description d...

  • Page 49

    Program 10 : system configuration setup 10-28 : sip system information setup level: sa description use program 10-28 : sip system information setup to set up basic sip trunking. Input data item no. Item input data description default 01 domain name up to 64 characters (ex. : userid@host- name.Domain...

  • Page 50

    Feature cross reference none sl1100 issue 4.0 2-30 program 10 : system configuration setup program 10

  • Page 51

    Program 10 : system configuration setup 10-29 : sip server information setup level: sa description use program 10-29 : sip server information setup to define the sip proxy setup for outbound/ inbound. The 10-29 commands are not used in non-registration mode. If entries are made in program 10-29-xx f...

  • Page 52

    Item no. Item input data description default 12 domain name up to 64 characters this specifies the domain name of the sip server. No setting 13 proxy host name up to 48 characters this specifies the host name of the sip server. No setting 14 sip carrier choice (v1.5 changed) 0 ~ 26 1 = carrier a 2 =...

  • Page 53

    Program 10 : system configuration setup 10-30 : sip authentication information setup level: in description use program 10-30 : sip authentication information setup to set the authentication options for sip trunks. Input data item no. Item input data description default 02 user name up to 64 characte...

  • Page 54

    Program 10 : system configuration setup 10-31 : network keep alive setup level: in (this program is available for v1.5 or higher) description use program 10-31 : network keep alive setup to set the interval and retry count of the aspirenet networking keep alive message. The keep alive is used for is...

  • Page 55

    Program 10 : system configuration setup 10-33 : sip registrar/proxy information basic setup level: in description use program 10-33 : sip registrar/proxy information basic setup to set the registrar/proxy options for sip extensions. Input data item no. Item input data description default 01 registra...

  • Page 56

    Program 10 : system configuration setup 10-36 : sip trunk registration information setup level: in description use program 10-36 : sip trunk registration information setup to set the sip trunk registration information. Input data register id 1 ~ 31 item no. Item input data description default 01 reg...

  • Page 57: 10-37 : Upnp Setup

    Program 10 : system configuration setup 10-37 : upnp setup level: in description use program 10-37 : upnp setup to set the upnp (universal plug and play) options for sip trunks. Input data item no. Item input data description default 01 upnp mode 0 = disable 1 = enable if the system controls the sip...

  • Page 58: 10-39 : Fractional Setup

    Program 10 : system configuration setup 10-39 : fractional setup level: in description use program 10-39 : fractional setup to enable or disable the ability to use fractional t1 or pri. Input data item no. Item input data description default 01 fractional 0 = disable (when disa- bled the system will...

  • Page 59

    Program 10 : system configuration setup 10-40 : ip trunk availability level: in description use program 10-40 : ip trunk availability to enable or disable the ability to use sip trunks and assign the number of ports if ip trunk is enabled. Input data slot number 0 item no. Item input data default 01...

  • Page 60

    Program 10 : system configuration setup 10-42 : virtual loop back port setting level: in description use program 10-42 : virtual loop back port setting to set the data for the virtual loop back port. Input data item no. Item input data default 01 number of loop back ports 0 ~ 30 (0 = no setting) 0 0...

  • Page 61

    Program 10 : system configuration setup 10-45 : ip routing table setup level: sa description use program 10-45 : ip routing table setup to set up the ip routing table. Input data routing table number 001 ~ 100 item no. Item input data default 01 network address 0.0.0.0 ~ 126.255.255.254 128.0.0.0 ~ ...

  • Page 62

    Program 10 : system configuration setup 10-46 : dr700 server information setup level: in description use program 10-46 : dr700 server information setup to set up the information of dr700 server. Input data item no. Item input data description default related program 01 register mode 0 = normal 1 = a...

  • Page 63

    Item no. Item input data description default related program 13 subscribe ses- sion port 0 ~ 65535 5081 14 nat mode 0 = off 1 = on when the system controls the sip multiline terminal via the nat router, this system data is set to on. 0 conditions none feature cross reference none issue 4.0 sl1100 pr...

  • Page 64

    Program 10 : system configuration setup 10-47 : terminal license server information setup level: in description use program 10-47 : terminal license server information setup to setup the information of terminal license server. Input data item no. Item input data description default 01 register port ...

  • Page 65: 10-48 : License Activation

    Program 10 : system configuration setup 10-48 : license activation level: in description use program 10-48 : license activation to turn on the license issued from the license server. Input data item no. Item input data default 01 software key code 20-digit character no setting 02 activation code 8-d...

  • Page 66

    Program 10 : system configuration setup 10-49 : license file activation level: in description use program 10-49 : license file activation to enable the command to save the license file via cf card which is issued from the license server. Input data item no. Item input data default 01 save license fi...

  • Page 67: 10-50 : License Information

    Program 10 : system configuration setup 10-50 : license information level: in description use program 10-50 : license information to confirm license information that is stored in a system. Input data feature code number 000 ~ 9999 item no. Item input data default 01 license name read only: character...

  • Page 68

    Program 10 : system configuration setup 10-51 : pri/t1 selection of pri level: in description use program 10-51 : pri/t1 selection of pri to select whether the unit works as pri or t1. Input data slot number 01 ~ 15 (v3.5 changed) item no. Item input data description default 01 pri/t1 selection 0 = ...

  • Page 69

    Program 10 : system configuration setup 10-52 : free/demo license information level: in description use program 10-52 : free/demo license information to display information on free of charge/demo license. Input data item no. Item input data default 01 remaining days of free/demo li- cense read only:...

  • Page 70

    Program 10 : system configuration setup 10-54 : license configuration for each package level: in description use program 10-54 : license configuration for each package to set the license information for each unit. Input data slot number 0 ~ 15 (v3.5 changed) license index number 1 ~ 32 item no. Item...

  • Page 71: 10-58 : Network Address

    Program 10 : system configuration setup 10-58 : network address level: in (this program is available for v1.5 or higher) description use program 10-58 : network address to set the local network address when the sip terminal (v4.0 or higher) terminal connects the system via a local router. Input data...

  • Page 72

    Feature cross reference none sl1100 issue 4.0 2-52 program 10 : system configuration setup program 10

  • Page 73: 10-60 : Audio Port Setup

    Program 10 : system configuration setup 10-60 : audio port setup level: in description use program 10-60 : audio port setup to defines which audio port on the 084m packages are used for bgm/external moh. Input data audio port number 1 = bgm 2 = external moh item no. Item input data description defau...

  • Page 74: 10-61 : Relay Port Setup

    Program 10 : system configuration setup 10-61 : relay port setup level: in description use program 10-61 : relay port setup to defines the relay port type on the 084m. Input data relay port no. 1 ~ 6 item no. Item input data default 01 relay type 0 = no setting 1 = external moh 2 = bgm resource 3 = ...

  • Page 75: 10-62 : Netbios Setting

    Program 10 : system configuration setup 10-62 : netbios setting level: in description use program 10-62 : netbios setting to set the data of netbios. Input data item no. Item input data description default 01 netbios mode 0 = disabled 1 = enabled 1 02 netbios name maximum 15 characters please avoid ...

  • Page 76: 10-63 : Dhcp Client Setting

    Program 10 : system configuration setup 10-63 : dhcp client setting level: in description use program 10-63 : dhcp client setting to set the data of dhcp client. Input data item no. Item input data description default 01 dhcp client mode 0 = disabled 1 = enabled if you are using ip phones/trunks it ...

  • Page 77: 10-65 : Ntp Server Setting

    Program 10 : system configuration setup 10-65 : ntp server setting level: in (this program is available for v4.0 or higher) description use program 10-65 : ntp server setting to set the ntp server. Input data item no. Item input data description default 01 ntp server 0 = disable (stop) 1 = enable (s...

  • Page 78: 11-01 : System Numbering

    Program 11 : system numbering 11-01 : system numbering level: in description use program 11-01 : system numbering to set the system numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other extensions and features...

  • Page 79

    Dial types dial type descrip- tion related program note 1 service code 11-10 : service code setup (for system administrator) on page 2-70 11-11 : service code setup (for setup/entry operation) on page 2-73 11-12 : service code setup (for service access) on page 2-77 11-14 : service code setup (for h...

  • Page 80

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 8 = networking access (v1.5 added), 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 2x 3 2 21 0 0 22...

  • Page 81

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 8 = networking access (v1.5 added), 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 4 * 0 0 4# 0 0 5...

  • Page 82

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 8 = networking access (v1.5 added), 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 79 0 0 70 0 0 7 ...

  • Page 83

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 8 = networking access (v1.5 added), 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 07 0 0 08 0 0 09...

  • Page 84

    Feature cross reference • flexible system numbering sl1100 issue 4.0 2-64 program 11 : system numbering program 11.

  • Page 85: 11-02 : Extension Numbering

    Program 11 : system numbering 11-02 : extension numbering level: in description use program 11-02 : extension numbering to set the extension number. The extension number can have up to eight digits. The first/second digit (s) of the number should be assigned in program 11-01 or program 11-20. This a...

  • Page 86

    Program 11 : system numbering 11-04 : virtual extension numbering level: in description use program 11-04 : virtual extension numbering to define the virtual extension numbers. The extension number can have up to eight digits. The first/second digit (s) of the number should be assigned in program 11...

  • Page 87

    Program 11 : system numbering 11-07 : department group pilot numbers level: in description use program 11-07 : department group pilot numbers to assign a pilot number to each department group set up in program 16-02. The pilot number is the number users dial for department calling and department ste...

  • Page 88: 11-09 : Trunk Access Code

    Program 11 : system numbering 11-09 : trunk access code level: in description use program 11-09 : trunk access code to assign the trunk access code. The trunk access code can be set from 1 ~ 4 digits which is defined to type 3 and 4 in program 11-01. This is the code extension users dial to access a...

  • Page 89

    Item no. Item input data description default related program 02 2nd trunk route access code dial (up to four digits) use this program to define addition- al trunk access codes. When a user dials the alternate trunk route access code, the sys- tem routes their call to the alternate trunk route. No se...

  • Page 90

    Program 11 : system numbering 11-10 : service code setup (for system administrator) level: in description use program 11-10 : service code setup (for system administrator) to customize the service codes for the system administrator. You can customize additional service codes in programs 11-11 ~ 11-1...

  • Page 91

    Item no. Item input data description default related program 16 leaving message waiting (re- quires cpu to be licensed for ho- tel/motel) 0~9, * , # maximum of 8 digit terminal: mlt 626 11-11-09 17 dial block by su- pervisor 0~9, * , # maximum of 8 digit terminal: mlt 601 90-19 18 off-premise call f...

  • Page 92

    Item no. Item input data description default related program 46 watch message setting 0~9, * , # maximum of 8 digit terminal: mlt, slt service code setting for watching message recording to vrs. 614 47 warning mes- sage setting 0~9, * , # maximum of 8 digit terminal: mlt, slt service code setting fo...

  • Page 93

    Program 11 : system numbering 11-11 : service code setup (for setup/entry operation) level: in description use program 11-11 : service code setup (for setup/entry operation) to customize the service codes which are used for registration and setup. You can customize additional service codes in progra...

  • Page 94

    Item no. Item input data description default related program 15 enable hands- free incoming in- tercom calls 0~9, * , # maximum of 8 digit terminal: mlt 721 20-09-05 20-02-12 16 force ringing of incoming inter- com calls 0~9, * , # maximum of 8 digit terminal: mlt 723 20-09-05 20-02-12 17 programmab...

  • Page 95

    Item no. Item input data description default related program 35 pilot group with- drawing 0~9, * , # maximum of 8 digit terminal: mlt, slt 650 36 toll restriction override 0~9, * , # maximum of 8 digit terminal: mlt, slt 663 21-14 37 ring volume set 0~9, * , # maximum of 8 digit terminal: mlt 729 38...

  • Page 96

    Item no. Item input data description default related program 58 call forward with personal greeting 0~9, * , # maximum of 8 digit terminal: mlt, slt 713 59 call forward to attendant except busy 0~9, * , # maximum of 8 digit terminal: mlt, slt 696 15-01-08 60 call forward to attendant/no an- swer 0~9...

  • Page 97

    Program 11 : system numbering 11-12 : service code setup (for service access) level: in description use program 11-12 : service code setup (for service access) to customize the service codes which are used for service access. You can customize additional service codes in programs 11-10, 11-11, and 1...

  • Page 98

    Item no. Item input data description default related program 11 group speed di- aling 0~9, * , # maximum of 8 digit terminal: mlt, slt #4 12 last number dial 0~9, * , # maximum of 8 digit terminal: mlt, slt #5 13 saved number dial 0~9, * , # maximum of 8 digit terminal: mlt, slt 715 14 trunk group a...

  • Page 99

    Item no. Item input data description default related program 35 station park hold 0~9, * , # maximum of 8 digit terminal: mlt, slt 757 36 door box access 0~9, * , # maximum of 8 digit terminal: mlt, slt 702 37 common cancel- ing service code 0~9, * , # maximum of 8 digit terminal: mlt, slt * 9 38 ge...

  • Page 100

    Item no. Item input data description default related program 63 watch mode start 0~9, * , # maximum of 8 digit terminal: mlt, slt service code (sc) setting for on/off watch mode. Sc+1;watch mode start sc+0; watch mode end. 717 64 security sensor mode start 0~9, * , # maximum of 8 digit terminal: mlt...

  • Page 101

    Program 11 : system numbering 11-13 : service code setup (for acd) level: in (this program is available for v1.5 or higher) description use program 11-13 : service code setup (for acd) to customize the service codes which are used with the automatic call distribution (acd) feature. You can customize...

  • Page 102

    Conditions none feature cross reference • automatic call distribution (acd) sl1100 issue 4.0 2-82 program 11 : system numbering program 11.

  • Page 103

    Program 11 : system numbering 11-14 : service code setup (for hotel) level: in description use program 11-14 : service code setup (for hotel) to customize the service codes which are used with the hotel/motel feature. You can customize additional service codes in programs 11-10 ~ 11-12, 11-15 and 11...

  • Page 104

    Item no. Item input data description default 09 set room to room call restriction 0~9, * , # maximum of 8 digit terminal: mlt, slt determine what the service code should be for an internal party to set room to room call restriction. 635 10 cancel room to room call restriction (hotel) 0~9, * , # maxi...

  • Page 105: Access)

    Program 11 : system numbering 11-15 : service code setup, administrative (for special access) level: in description use program 11-15 : service code setup, administrative (for special access) to customize the special access service codes which are used by the administrator in the hotel/motel feature...

  • Page 106

    Feature cross reference none sl1100 issue 4.0 2-86 program 11 : system numbering program 11.

  • Page 107

    Program 11 : system numbering 11-16 : single digit service code setup level: in description use program 11-16 : single digit service code setup to customize the one-digit service codes used when a busy or ring back signal is heard. You can customize additional service codes in programs 11-10 ~ 11-15...

  • Page 108

    Program 11 : system numbering 11-17 : acd group pilot number level: in (this program is available for v1.5 or higher) description use program 11-17 : acd group pilot number to assign the acd master number for each acd group. This is the number a user dials to transfer calls to the acd group. Normall...

  • Page 109

    Program 11 : system numbering 11-19 : remote conference pilot number setup level: in description use program 11-19 : remote conference pilot number setup to assign the pilot number to be used for the remote conference. This is the number that outside parties will call in order to connect to a confer...

  • Page 110

    Program 11 : system numbering 11-20 : dial extension analyze table level: in description use program 11-20 : dial extension analyze table to define the dial type based on three or more digits. This program is relevant only if digits in 11-01-01 are set to 9 (dial extension analyze). Input data dial ...

  • Page 111

    Program 12 : night mode setup 12-01 : night mode function setup level: in description use program 12-01 : night mode function setup to set up the night mode options. Refer to the following chart for a description of each option, its range and default setting. Input data item no. Item input data desc...

  • Page 112

    Program 12 : night mode setup 12-02 : automatic night service patterns level: sa description use program 12-02 : automatic night service patterns to define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The dai...

  • Page 113

    Time pattern 2 00 : 00 00 : 00 mode 2 (night) time setting 01 : 00 : 00 to 00 : 00 mode 2 (night) default time pattern 1 set time number start time end time mode 01 0000 0800 2 02 0800 1700 1 03 1700 0000 2 04 0000 0000 1 : : : : 20 0000 0000 1 time pattern 2 set time number start time end time mode...

  • Page 114

    Program 12 : night mode setup 12-03 : weekly night service switching level: sa description use program 12-03 : weekly night service switching to define a weekly schedule of night-switch settings. 21-02 : trunk group routing for extensions input data night mode service group number 01 ~ 04 item no. I...

  • Page 115

    Program 12 : night mode setup 12-04 : holiday night service switching level: sa description use program 12-04 : holiday night service switching to define a yearly schedule of holiday night- switch settings. This schedule is used for the setting of special days when the company is expected to be clos...

  • Page 116

    Program 12 : night mode setup 12-05 : night mode group assignment for extensions level: in description use program 12-05 : night mode group assignment for extensions to a assign day/night mode group for each extension. Input data extension number up to eight digits item no. Item input data descripti...

  • Page 117

    Program 12 : night mode setup 12-06 : night mode group assignment for trunks level: in description use program 12-06 : night mode group assignment for trunks to assign a day/night mode group for each trunk port. Input data trunk port number 001 ~ 084 item no. Item input data description default 01 n...

  • Page 118

    Program 12 : night mode setup 12-07 : text data for night mode level: in description use program 12-07 : text data for night mode to make an original text message which is displayed on an lcd of multiline telephone in each mode. Input data night mode service group number 01 ~ 04 day/night mode 1 ~ 8...

  • Page 119

    Program 12 : night mode setup 12-08 : night mode service range level: sa description use program 12-08 : night mode service range to define the changing range of toggle key for each day/night mode. Input data night mode service group number 01 ~ 04 item no. Item input data description default 01 ran...

  • Page 120

    Program 13 : abbreviated dialing 13-01 : speed dialing option setup level: in description use program 13-01 : speed dialing option setup to define the speed dialing functions. Input data item no. Item input data description default related program 01 speed dialing auto outgoing call mode 0 = trunk o...

  • Page 121

    Program 13 : abbreviated dialing 13-02 : group speed dialing bins level: in description use program 13-02 : group speed dialing bins to define the range of bin numbers to be used by each speed dialing group. (refer to 13-03 : speed dialing group assignment for extensions on page 2-102 .) input data ...

  • Page 122

    Program 13 : abbreviated dialing 13-03 : speed dialing group assignment for extensions level: in description use program 13-03 : speed dialing group assignment for extensions to assign speed dialing group for each extension. There are 32 available speed dialing groups. Input data extension number up...

  • Page 123

    Program 13 : abbreviated dialing 13-04 : speed dialing number and name level: sb description use program 13-04 : speed dialing number and name to store speed dialing data in the speed dialing areas. This program is also used to define the names assigned to the speed dialing numbers. Input data speed...

  • Page 124

    Item no. Item input data description default related program 04 transfer destina- tion number if transfer mode is (refer to 13-04-03) : 1 = internal dial mode 1 ~ 9, 0, * , #, p, r, @ (maximum 36 charac- ters) 2 = incoming ring group 0 ~ 25 (irg number) p = pause r = recall @ = additional digits whe...

  • Page 125

    Program 13 : abbreviated dialing 13-05 : speed dial trunk group level: sb description use program 13-05 : speed dialing trunk group to define the trunk group to be seized for each speed dialing number. If this program has an entry of 0 (no setting), then seizing a line follows the trunk access group...

  • Page 126

    Program 13 : abbreviated dialing 13-06 : speed dial number and name level: sb description use program 13-06 : speed dial number and name to set up the dial number and name of each speed dial number. Input data extension number up to 8 digits speed dial number 01 ~ 20 item no. Item input data default...

  • Page 127

    Program 13 : abbreviated dialing 13-11 : abbreviated dial group name level: sb description use program 13-11 : abbreviated dial group name to set the name of abbreviated dial group name. Input data group number 01 ~ 32 item no. Item input data default 01 group name up to 12 characters 1 = abb : grou...

  • Page 128

    Program 14 : trunk, basic setup 14-01 : basic trunk data setup level: in description use program 14-01 : basic trunk data setup to set the basic options for each trunk port. Refer to the chart below for a description of each option, its range and default setting. Input data trunk port number 001 ~ 0...

  • Page 129

    Item no. Item input data description default related program 09 private line 0 = disable private line (normal) 1 = enable private line (private line) 0 10 dtmf tones for outgoing calls 0 = disable (no) 1 = enable (yes) use this option to enable (1) or disa- ble (0) dtmf tones for outgoing trunk call...

  • Page 130

    Item no. Item input data description default related program 24 trunk-to-trunk outgoing caller id through mode 0 = disable (caller id not forwarded out.) 1 = enable (caller id is forwarded out.) enable (1) or disable (0) the ability to send the original caller id through when the call is forward off...

  • Page 131

    Item no. Item input data description default related program 40 isdn queue an- nouncement connect mode (v2.0 added) 0 = send connect 1 = send progress #8 when a vrs queue message is to be played back (configured in prg 22-14, prg 22-15, prg 41-11, or prg 41-19, the system shall, in- stead of a conne...

  • Page 132

    Program 14 : trunk, basic setup 14-02 : analog trunk data setup level: in description use program 14-02 : analog trunk data setup to set the basic options for each analog trunk port. Refer to the table below for a description of each option, its range and default setting. Input data trunk port numbe...

  • Page 133

    Item no. Item input data description default related program 07 dp to dtmf con- version options 0 = automatic 1 = automatic and manual 2 = manual determine how a user can convert a dial pulse (dp) call to a dtmf call. For each trunk, set the type of dp to dtmf conversion required. There are three co...

  • Page 134

    Conditions none feature cross reference none sl1100 issue 4.0 2-114 program 14 : trunk, basic setup program 14.

  • Page 135: 14-04 : Behind Pbx Setup

    Program 14 : trunk, basic setup 14-04 : behind pbx setup level: in description use program 14-04 : behind pbx setup to indicate if the trunk is installed behind a pbx. There is one item for each mode. Input data trunk port number 001 ~ 084 day/night mode 1 ~ 8 item no. Item input data default relate...

  • Page 136: 14-05 : Trunk Group

    Program 14 : trunk, basic setup 14-05 : trunk group level: in description use program 14-05 : trunk group to assign trunks to trunk groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in the...

  • Page 137: 14-06 : Trunk Group Routing

    Program 14 : trunk, basic setup 14-06 : trunk group routing level: in description use program 14-06 : trunk group routing to set up an outbound routing table for the trunk groups you assigned in program 14-05. When a user dial 9, the system routes their calls in the order (priority) specified. For e...

  • Page 138

    Default route no. Order data route 1 1 1 (trunk group 1) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) route 2 1 0 (not specified) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) : 1 0 (not specified) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) route 25 1 0 ...

  • Page 139

    Program 14 : trunk, basic setup 14-07 : trunk access map setup level: in description use program 14-07 : trunk access map setup to set up the trunk access maps. This sets an extension access options for trunks. For example, an extension can place only outgoing calls on trunks to which it has outgoin...

  • Page 140

    Access map no. Trunk port no. Default : 1 7 (t, r, h) 2 7 (t, r, h) : : 084 7 (t, r, h) 084 1 7 (t, r, h) 2 7 (t, r, h) : : 084 7 (t, r, h) conditions none feature cross reference • central office calls, answering • central office calls, placing sl1100 issue 4.0 2-120 program 14 : trunk, basic setup...

  • Page 141

    Program 14 : trunk, basic setup 14-08 : music on hold source for trunks level: in description use program 14-08 : music on hold source for trunks to define a music on hold source for a trunk as coi port. Input data trunk port number 001 ~ 084 item no. Item input data description default 01 moh type ...

  • Page 142

    Program 14 : trunk, basic setup 14-09 : conversation recording destination for trunks level: in description use program 14-09 : conversation recording destination for trunks to set the conversation recording destination for each trunk. If both programs 14-09 and 15-12 define a destination, the desti...

  • Page 143

    Program 14 : trunk, basic setup 14-11 : id setup for ip trunk level: in description use program 14-11 : id setup for ip trunk to set the id of each ip trunk. This program refers to incoming and outgoing ip trunk calls. The id is sent on an outgoing ip trunk call. This program is used only for h.323....

  • Page 144

    Program 14 : trunk, basic setup 14-12 : sip register id setup for ip trunk level: in description use program 14-12 : sip register id setup for ip trunk to define the sip register id for ip trunks. Input data trunk port number 001 ~ 084 item no. Item input data default 01 register id 0 ~ 31 0 02 pilo...

  • Page 145

    Program 15 : extension, basic setup 15-01 : basic extension data setup level: sa description use program 15-01 : basic extension data setup to define the basic settings for each extension. Input data extension number maximum eight digits item no. Item input data description default related program 0...

  • Page 146

    Item no. Item input data description default related program 10 extension num- ber 0 = off (when set to off the system will not send any outbound calling party informa- tion.) 1 = on (when set to on the system will send calling party informa- tion.) this program enables/disables the ability to send ...

  • Page 147

    Program 15 : extension, basic setup 15-02 : multiline telephone basic data setup level: in description use program 15-02 : multiline telephone basic data setup to set up various multiline telephone options. Input data extension number maximum eight digits item no. Item input data description default...

  • Page 148

    Item no. Item input data description default related program 05 transfer key op- eration mode 0 = transfer 1 = call back 2 = hook use this option to set the operating mode of the extension transfer key. The keys can be for call transfer, serial calling or flash. When select- ing the flash option (se...

  • Page 149

    Item no. Item input data description default related program 21 virtual extension access mode (when idle virtual extension key pressed) 0 = dss 1 = outgoing (otg) 2 = ignore determine whether a virtual exten- sion (ve) should function as a dss key or a virtual extension. When dss (0) is selected, th...

  • Page 150

    Item no. Item input data description default related program 36 message waiting lamp cycle for called extension 1 = cycle 1 2 = cycle 2 3 = cycle 3 4 = cycle 4 5 = cycle 5 6 = cycle 6 7 = cycle 7 select the cycle method that the large led flashes when the exten- sion has message waiting set to the e...

  • Page 151

    Item no. Item input data description default related program 58 display mode of trunk incoming (v1.5 deleted) 0 = caller id 1 = memo information 0 13-04-08 13-04-09 13-04-10 60 soft key/naviga- tion key mode 0 = standard mode 1 = advanced mode1 2 = advanced mode2 2 61 backlight max brightness 0 ~ 8 ...

  • Page 152

    Program 15-02 - incoming signal frequency patterns incoming signal fre- quency pattern type frequency 1 frequency 2 modulation external incoming signal frequency (pattern 1) high middle low 1100 hz 660 hz 520 hz 1400 hz 760 hz 660 hz 16 hz 16 hz 16 hz external incoming signal frequency (pattern 2) h...

  • Page 153

    Program 15 : extension, basic setup 15-03 : single line telephone basic data setup level: in description use program 15-03 : single line telephone basic data setup to set up various single line telephone options. Input data extension number maximum eight digits item no. Item input data description d...

  • Page 154

    Item no. Item input data description default related program 09 caller id func- tion - for exter- nal module 0 = disable (caller id not displayed.) 1 = enable (caller id is displayed.) enable (1) or disable (0) the caller id fsk signal for an external caller id module or a 3rd party vendor tel- epho...

  • Page 155

    (1) (2) (3) (4) (5) normal reverse reverse reverse normal normal idle idle idle outgoing call incoming call call pickup (1) = off-hook (2) = calling/ringing (3) = answer (4) = detect hang up (5) = on-hook conditions none feature cross reference • single line telephones issue 4.0 sl1100 programming m...

  • Page 156

    Program 15 : extension, basic setup 15-05 : ip telephone terminal basic data setup level: in description use program 15-05 : ip telephone terminal basic data setup to set up the basic settings for an ip telephone. Input data extension number maximum eight digits item no. Item input data description ...

  • Page 157

    Item no. Item input data description default related program 18 ip duplication al- lowed group 0 = not used 1 = group 1 2 = group 2 3 = group 3 4 = group 4 5 = group 5 6 = group 6 7 = group 7 8 = group 8 9 = group 9 10 = group 10 if there is an adapter that has one ip address coming into it but has ...

  • Page 158

    Item no. Item input data description default related program 40 calling name dis- play info via trunk for stand- ard sip 0 = both name and number 1 = name only 2 = number only 3 = none 0 41 time zone(hour) 0 ~ 24 (- 12 ~ + 12 hour) 12 43 video mode 0 = disable 1 = enable 0 44 using std-sip display f...

  • Page 159

    Program 15 : extension, basic setup 15-06 : trunk access map for extensions level: in description use program 15-06 : trunk access map for extensions to define the trunk access map for each extension. An extension can place only outgoing calls on trunks to which it has outgoing access. Use program 1...

  • Page 160

    Program 15 : extension, basic setup 15-07 : programmable function keys level: sa description use program 15-07 : programmable function keys to assign functions to a multiline terminal line keys. For certain functions, you can append data to the key basic function. For example, the function 26 append...

  • Page 161

    Table 2-2 function number list [1] normal function code (00 ~ 99, #00 ~ #99) (service code 751) function number function additional data led indication note 01 dss/one-touch extension number or any numbers (up to 36 digits) on (red) : dss ext. Busy off : dss ext. Idle, dnd external, dnd transfer, cf...

  • Page 162

    Function number function additional data led indication note 27 speed dial - common/private speed dial number (common / private) none 28 speed dial - group speed dial number (group) none 29 repeat redial on (red) : repeat dialing 30 saved number redial none 31 memo dial none 32 meet - me con- ferenc...

  • Page 163

    Function number function additional data led indication note 55 extension name change none 56 general purpose led operation 001 ~ 100 : (red) on off 001 ~ 100 : (red) on off 57 general purpose led indication 001 ~ 100 : (red) on off 001 ~ 100 : (red) on off 58 automatic trans- fer at department grou...

  • Page 164

    Function number function additional data led indication note 83 conversation re- cording function (vmsu) 0 = pause 1 = re-recording 2 = address 3 = erase 4 = urgent page 84 drop key none 86 private call re- fuse none off : cancel slow blink (red) : set 87 caller id refuse none off : cancel slow blin...

  • Page 165

    Func- tion number function additional da- ta led indication note * 04 park key park number (01 ~ 64) slow blink (green) : holding(own) fast blink (green) : recall(own) slow blink (red) : holding(other) * 05 loop keys use programs 15-13-01 and/or 15-13-02 to as- sign the loop key to a trunk group. 0 ...

  • Page 166

    L e d p a tte rn 0 :[o f f ] l e d p a tte rn 1 :[f l : o n (5 0 0 m s)/off(5 0 0 m s)] o n o ff o n o ff l e d p a tte rn 2 :[w k : o n (2 5 0 m s)/off(2 5 0 m s)] o n o ff l e d p a tte rn 3 :[r w : o n (1 2 5 m s)/off(1 2 5 m s)] o n o ff l e d p a tte rn 4 :[ir : o n (1 2 5 m s)/off(1 2 5 m s)/ ...

  • Page 167

    Program 15 : extension, basic setup 15-08 : incoming virtual extension ring tone setup level: in description use program 15-08 : incoming virtual extension ring tone setup to assign a ring tone range (0 ~ 4) to incoming virtual extensions assigned to a virtual extension key (program 15-07). If you e...

  • Page 168

    Conditions none feature cross reference none sl1100 issue 4.0 2-148 program 15 : extension, basic setup program 15.

  • Page 169

    Program 15 : extension, basic setup 15-09 : virtual extension ring assignment level: sa description use program 15-09 : virtual extension ring assignment to assign the ringing options for an extension virtual extension key or virtual extension group answer key which is defined in program 15-07. You ...

  • Page 170

    Program 15 : extension, basic setup 15-10 : incoming virtual extension ring tone order setup level: sa description use program 15-10 : incoming virtual extension ring tone order setup to set the priority (1 ~ 4) for the virtual extension ring tones set in program 15-08. When virtual extension calls ...

  • Page 171

    Program 15 : extension, basic setup 15-11 : virtual extension delayed ring assignment level: sa description use program 15-11 : virtual extension delayed ring assignment to assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in progra...

  • Page 172

    Program 15 : extension, basic setup 15-12 : conversation recording destination for extensions level: in description use program 15-12 : conversation recording destination for extensions to set the conversation recording destination for each extension. If both programs 14-09 and 15-12 define a destin...

  • Page 173: 15-13 : Loop Keys

    Program 15 : extension, basic setup 15-13 : loop keys level: in description use program 15-13 : loop keys to assign the loop key data for each keyset terminal. Loop keys can be incoming, outgoing or both ways. Outgoing loop keys use the entry in item 1. Incoming loop keys use the entry in item 2. Bo...

  • Page 174

    Program 15 : extension, basic setup 15-14 : programmable one-touch keys level: sb description use program 15-14 : programmable one-touch keys to define the one-touch key data for each multiline terminal. For each sl1100 wireless telephone to use the transfer when out of range feature, enter the dest...

  • Page 175

    Program 15 : extension, basic setup 15-16 : sip register id setup for extension level: in description use program 15-16 : sip register id setup for extension to define the sip register id for extensions. Input data extension number maximum eight digits item no. Item input data default 01 register id...

  • Page 176

    Program 15 : extension, basic setup 15-17 : co message waiting indication level: in description use program 15-17 : co message waiting indication to set the message waiting led flash assignment on each co line. Input data extension number including virtual extensions up to eight digits trunk port nu...

  • Page 177

    Program 15 : extension, basic setup 15-18 : virtual extension key enhanced options level: in description use program 15-18 : virtual extension key enhanced options to define the operation when a virtual extension key is pressed. Input data extension number including virtual extensions up to eight di...

  • Page 178

    Condition • if a dil rings a virtual extension, the virtual extension key operation mode must be set to 1. Feature cross reference none sl1100 issue 4.0 2-158 program 15 : extension, basic setup program 15.

  • Page 179

    Program 15 : extension, basic setup 15-22 : mobile extension setup level: in description use program 15-22 : mobile extension setup to set the system information for the mobile extension feature. Input data extension number up to eight digits item no. Item input data description default 01 mobile ex...

  • Page 180

    Program 15 : extension, basic setup 15-24 : registration of standard sip terminal level: in (this program is available for v1.5 or higher) description use program 15-24 : registration of standard sip terminal to register data in the standard sip terminal where register is not used. Input data item n...

  • Page 181

    Program 15 : extension, basic setup 15-28 : trunk incoming ring tone of extension setup level: in (this program is available for v1.5 or higher) description use program 15-28 : trunk incoming ring tone of extension setup to define the ringing tone for each trunk port of extension. Input data extensi...

  • Page 182

    Program 16 : department group setup 16-01 : department group basic data setup level: in description use program 16-01 : department group basic data setup to set the function mode for each department group. There are 32 available department groups. Input data department group number 1 ~ 32 item no. I...

  • Page 183

    Item no. Item input data description default related program 08 maximum queu- ing number for department group call 0 ~ 32 0 = no queuing this program sets the amount of calls that can queue to a department group when all members of the group are busy. 0 09 department hunting no an- swer time 0 ~ 648...

  • Page 184

    Program 16 : department group setup 16-02 : department group assignment for extensions level: in description use program 16-02 : department group assignment for extensions to set the department groups. The system uses these groups (32 department groups) for department calling. Assign pilot numbers t...

  • Page 185

    Program 16 : department group setup 16-03 : secondary department group level: in description use program 16-03 : secondary department group to set a second department group for extensions. Up to 16 extensions can be assigned per a department group. There are 32 available department groups. Input dat...

  • Page 186

    Program 16 : department group setup 16-04 : call restriction between department groups level: in description use program 16-04 : call restriction between department groups to set internal calls between members of different department (station) groups that can be restricted on a per group basis. Each...

  • Page 187: 20-01 : System Options

    Program 20 : system option setup 20-01 : system options level: in description use program 20-01 : system options to set various system options. Input data item no. Item input data description default related program 01 operator access mode 0 = step call 1 = circular use this program to set up priori...

  • Page 188

    Item no. Item input data description default related program 20 progresstone for mobile exten- sion setting (v4.0 added) 0 = disable 1 = enable enable/disable the progressive- tone when calling a mobile exten- sion. 1 conditions none feature cross reference none sl1100 issue 4.0 2-168 program 20 : s...

  • Page 189

    Program 20 : system option setup 20-02 : system options for multiline telephones level: in description use program 20-02 : system options for multiline telephones to set various system options for multiline telephones. Input data item no. Item input data description default related program 01 trunk ...

  • Page 190

    Item no. Item input data description default related program 07 time and date dis- play mode 1 ~ 8 type 1 = (12 hour) 10 mar tue 3 : 15 pm type 2 = (12 hour) 3 : 15 pm mar 10 tue type 3 = (12 hour) 3-10 tue 3 : 15 pm type 4 = (12 hour) 3 : 15 pm tue 10 mar type 5 = (24 hour) 10 mar tue 15 : 15 type ...

  • Page 191

    Item no. Item input data description default related program 19 dss key - virtual extension mode 0 = no 1 = yes sets the mode of a virtual ex- tension key that appears on a dss con- sole. 0 24 lcd scroll mode 0 = character 1 = dot 0 conditions none feature cross reference none issue 4.0 sl1100 progr...

  • Page 192

    Item no. Item input data description default 10 subnet mask 128.0.0.0

  • Page 193

    Item no. Item input data description default related program 06 headset ringing start time (for slt) 0 ~ 64800 seconds define the headset ringing start time. After this time expires from the time when a single line telephone is off-hook, the system sets the single line telephone to headset ringing m...

  • Page 194

    Program 20 : system option setup 20-04 : system options for virtual extensions level: in description use program 20-04 : system options for virtual extensions to set up various system options for virtual extensions. There are 50 available virtual extension ports. Input data item no. Item input data ...

  • Page 195

    Program 20 : system option setup 20-06 : class of service for extensions level: in description use program 20-06 : class of service for extensions to assign a class of service (cos) to an extension. There are 15 classes of service that can be assigned. To specify the options in each class of service...

  • Page 196

    Program 20 : system option setup 20-07 : class of service options (administrator level) level: in description use program 20-07 : class of service options (administrator level) to define the administrator service availability for each extension class of service (cos). Input data class of service num...

  • Page 197

    Item no. Item input data description default related program 15 vrs general message record/ delete 0 = off 1 = on turns off or on an extension user ability to dial service code 612 and record, listen to, or erase the gener- al message. Cos1 ~ 14/ cos15 = 0/1 11-10-22 18 smdr printout accumulated ex-...

  • Page 198

    Program 20 : system option setup 20-08 : class of service options (outgoing call service) level: in description use program 20-08 : class of service options (outgoing call service) to define the outgoing call feature availability for each extension class of service (cos). Input data class of service...

  • Page 199

    Item no. Item input data description default related program 13 isdn clip 0 = off (when set to off the system will not send any outbound calling party informa- tion.) 1 = on (when set to on the system will send calling party informa- tion for the station or trunk.) determines if the isdn calling lin...

  • Page 200

    Program 20 : system option setup 20-09 : class of service options (incoming call service) level: in description use program 20-09 : class of service options (incoming call service) to define the incoming call feature availability for each extension class of service (cos). Input data class of service...

  • Page 201

    Conditions none feature cross reference • class of service issue 4.0 sl1100 programming manual 2-181 program 20

  • Page 202

    Program 20 : system option setup 20-10 : class of service options (answer service) level: in description use program 20-10 : class of service options (answer service) to define the answer feature availability for each extension class of service (cos). Input data class of service number 01 ~ 15 item ...

  • Page 203

    Feature cross reference none issue 4.0 sl1100 programming manual 2-183 program 20

  • Page 204

    Program 20 : system option setup 20-11 : class of service options (hold/transfer service) level: in description use program 20-11 : class of service options (hold/transfer service) to define the hold and transfer feature availability for each extension class of service (cos). Input data class of ser...

  • Page 205

    Item no. Item input data description default 16 call redirect 0 = off 1 = on turns off or on a multiline terminal user ability to transfer a call to a predefined destination (such as an operator, voice mail, or another extension) without an- swering the call. Cos 01 ~ 15 = 1 17 department group trun...

  • Page 206

    Program 20 : system option setup 20-12 : class of service options (charging cost service) level: in description use program 20-12 : class of service options (charging cost service) to define the charging cost service availability for each extension service class. Input data class of service number 0...

  • Page 207

    Program 20 : system option setup 20-13 : class of service options (supplementary service) level: in description use program 20-13 : class of service options (supplementary service) to define the supplementary feature availability for each extension class of service (cos). Input data class of service...

  • Page 208

    Item no. Item input data description default related program 12 room monitor, extension being monitored 0 = off 1 = on turn off or on an extension ability to be monitored by other extensions. Cos 01 ~ 15 = 1 13 continued dial- ing (dtmf) sig- nal on icm call 0 = off 1 = on turn off or on an extensio...

  • Page 209

    Item no. Item input data description default related program 29 paging display 0 = off 1 = on turns off or on an extension user ability to display paging information. Cos 01 ~ 15 = 1 30 background mu- sic 0 = deny (user cannot control background mu- sic on their station.) 1 = allow (user can control...

  • Page 210

    Item no. Item input data description default related program 49 blf indication on co incoming state 0 = off (disabled) 1 = on (enabled) determine if a blf of the station will light when a normal co call is ring- ing the phone. Cos 01 ~ 15 = 0 51 number and name appear in the directory 0 = off 1 = on...

  • Page 211

    Program 20 : system option setup 20-14 : class of service options for disa/e&m level: in description use program 20-14 : class of service options for disa/e&m to enable/disable disa and tie line class of service options. You assign a disa class of service to disa users in program 25-09. Assign tie l...

  • Page 212

    Item no. Item input data description default 10 call forward setting by remote via disa 0 = off 1 = on enable or disable a disa caller ability to use the call forward service codes (pro- grams 11-11-01 ~ 11-11-05). Cos 01 ~ 15 = 0 11 disa/tie trunk barge-in 0 = off 1 = on this option enables or disa...

  • Page 213: 20-15 : Ring Cycle Setup

    Program 20 : system option setup 20-15 : ring cycle setup level: in description use program 20-15 : ring cycle setup to define the ringing cycles for each ring type. Input data item no. Item input data default 01 incoming signal type : normal in- coming call on trunk ringing cycle number : 1 ~ 13 2 ...

  • Page 214

    Number ringing cycle 11 on : 0.25 / off : 0.25 / on : 0.25 / off : 4.25 12 on : 1.0 / off : 3.0 13 on : 0.25 / off : 0.25 / on : 0.25 / off : 2.25 conditions none feature cross reference none sl1100 issue 4.0 2-194 program 20 : system option setup program 20

  • Page 215

    Program 20 : system option setup 20-16 : selectable display messages level: sa description use program 20-16 : selectable display messages to enter the selectable display messages. There are 20 alphanumeric messages, with up to 48 characters. Use the following chart when programming messages. Use th...

  • Page 216

    Number message 5 busy call after ## : ## 6 out for lunch back ## : ## 7 business trip back ## / ## 8 business trip ########## 9 gone for the day 10 on vacation until ## / ## 11 message 11 12 message 12 13 message 13 14 message 14 15 message 15 16 message 16 17 message 17 18 message 18 19 message 19 ...

  • Page 217: 20-17 : Operator Extension

    Program 20 : system option setup 20-17 : operator extension level: in description use program 20-17 : operator extension to designate an operator. When an extension user dials 0 (defined by program 11-01 type 5), calls go to the operator selected in this program. If you do not assign an extension in...

  • Page 218: 20-18 : Service Tone Timers

    Program 20 : system option setup 20-18 : service tone timers level: in description use program 20-18 : service tone timers to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Input data item no. Item inpu...

  • Page 219

    Program 20 : system option setup 20-19 : system options for caller id level: in description use program 20-19 : system options for caller id to define the system options for the caller id feature. Input data item no. Item input data description default 01 caller id displaying format 0 = first 10 dig...

  • Page 220

    Program 20 : system option setup 20-20 : message setup for non-caller id data level: in description use program 20-20 : message setup for non-caller id data to define the messages which are displayed when no caller id information is received. Input data item no. Item input data default 01 private ca...

  • Page 221

    Program 20 : system option setup 20-21 : system options for long conversation level: in description use program 20-21 : system options for long conversation to define the system options for the long conversation feature. Input data item no. Item input data description default related program 01 long...

  • Page 222

    Program 20 : system option setup 20-23 : system options for cti level: in description use program 20-23 : system options for cti to define the system options for the cti feature. Input data item no. Item input data description default 01 delayed ring timer for cti 0 ~ 64800 seconds 30 seconds 02 ale...

  • Page 223: 20-25 : Isdn Options

    Program 20 : system option setup 20-25 : isdn options level: in description use program 20-25 : isdn options to define the isdn system options. Input data item no. Item input data description default 01 send the release message after sub- scriber hangs up 0 = service off 1 = service on 1 02 progress...

  • Page 224

    Item no. Item input data description default 14 no response release send 0 = off 1 = on operation mode setting for when second t303 timer expires. 0 15 call reference selec- tion for pri 2b-ch transfer 0 = off 1 = on 0 18 include cpn on pre- sentation restriction (v3.0 added) 0 = not include 1 = inc...

  • Page 225

    Program 20 : system option setup 20-26 : multiplier for charging cost level: in description use program 20-26 : multiplier for charging cost to define the multiplier for charging cost to each extension service class. Input data service class 01 ~ 15 item no. Item input data default 01 value (%) 100 ...

  • Page 226

    Program 20 : system option setup 20-28 : trunk to trunk conversation level: in description use program 20-28 : trunk to trunk conversation to define system options for trunk to trunk conversation. Input data item no. Item input data description default related program 01 conversation continue code 0...

  • Page 227

    Program 20 : system option setup 20-29 : timer class for extension level: in description use program 20-29 : timer class for extension to assign the timer class to each extension. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. Thi...

  • Page 228

    Program 20 : system option setup 20-30 : timer class for trunks level: in description use program 20-30 : timer class for trunks to assign the timer class to each trunk. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. The details o...

  • Page 229

    Program 20 : system option setup 20-31 : timer class timer assignment level: in description use program 20-31 : timer class timer assignment to assign values to the timers on a class of service basis. Input data timer class number 0 ~ 15 item no. Item input data description default related program 0...

  • Page 230

    Item no. Item input data description default related program 10 hold recall time (non exclusive hold) 0 ~ 64800 seconds a call on hold recalls the extension that placed it on hold after this time. This time works with the hold recall callback time (program 24-01-02 ). 60 (v1.5 changed) 24-01-01 11 h...

  • Page 231

    Item no. Item input data description default related program 22 disa external paging time 0 ~ 64800 seconds this is the maximum length of an external page placed by a disa caller. If the page continues longer than this time, the system termi- nates the disa call. 30 25-07-10 23 page announce- ment d...

  • Page 232

    Program 20 : system option setup 20-34 : remote conference group setup level: sa description use program 20-34 : remote conference group setup to define the remote conference options. Input data remote conference group number 1 ~ 4 item no. Item input data description default 01 conference name up t...

  • Page 233

    Program 20 : system option setup 20-35 : extension's operator setting level: in description use program 20-35 : extension’s operator setting to assign an extension to an operator group. Input data extension number up to eight digits item no. Item input data default 01 extension’s operator setting 0 ...

  • Page 234

    Program 20 : system option setup 20-36 : trunk's operator setting level: in description use program 20-36 : trunk’s operator setting to assign a trunk to an operator group. Input data trunk port number 001 ~ 084 item no. Item input data description default 01 trunk’s operator set- ting 0 ~ 15 (0 = n...

  • Page 235

    Program 20 : system option setup 20-37 : operator extension group setup level: in description use program 20-37 : operator extension group setup to define the operator(s) in the operator group. Input data operator group 1 ~ 15 operator number 1 ~ 8 item no. Item input data default 01 operator extens...

  • Page 236

    Program 20 : system option setup 20-38 : operator group setting level: in description use program 20-38 : operator group setting to set up priority of a call when calling an operator telephone. Input data operator group 1 ~ 15 item no. Item input data description default 01 operator access mode 0 = ...

  • Page 237

    Program 20 : system option setup 20-42 : night mode for each package level: in description use program 20-42 : night mode for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 15 (v3.5 changed) item no. Item input d...

  • Page 238

    Program 20 : system option setup 20-43 : power supply for each package level: in description use program 20-43 : power supply for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 15 (v3.5 changed) operation mode 01...

  • Page 239: 20-44 : Watch Mode Setup

    Program 20 : system option setup 20-44 : watch mode setup level: in description use program 20-44 : watch mode setup to defines the watch mode. Input data item no. Item input data description default 01 internal paging group for watch message 0 ~ 32 define internal paging group number for watching m...

  • Page 240: 20-45 : Remote Watch Setup

    Program 20 : system option setup 20-45 : remote watch setup level: in description use program 20-45 : remote watch setup to defines the remote watch. Input data terminal number 1 ~ 6 item no. Item input data description default 01 ring terminal for re- mote inspection extension number (up to 8 digit...

  • Page 241

    Program 20 : system option setup 20-46 : security sensor setup level: in description use program 20-46 : security sensor setup to defines the security sensor. Input data security sensor number 1 ~ 6 item no. Item input data description default 01 sensor mode 0 = off 1 = on define door port (084m 3, ...

  • Page 242

    Program 20 : system option setup 20-47 : time pattern setting for watch mode level: in description use program 20-47 : time pattern setting for watch mode to defines the watch mode time pattern. Input data time pattern 01 ~ 08 item no. Item input data description default 01 watch mode time pattern 0...

  • Page 243

    Program 20 : system option setup 20-48 : time pattern setting for security sensor level: in description use program 20-48 : time pattern setting for security sensor to defines the security sensor time pattern. Input data time pattern 01 ~ 08 item no. Item input data description default 01 security s...

  • Page 244

    Program 20 : system option setup 20-49 : caller id shared group basic data setup level: in description use program 20-49 : caller id shared group basic data setup to defines the function mode for each caller id shared group. Input data caller id shared group number 01 ~ 08 item no. Item input data d...

  • Page 245

    Program 20 : system option setup 20-55 : delay timer for security sensor level: in (this program is available for v1.5 or higher) description use program 20-55 : delay timer for secuirty sensor to set time for security to be operational. Once it reach the time the security will starts if the securit...

  • Page 246

    Program 21 : outgoing call setup 21-01 : system options for outgoing calls level: in description use program 21-01 : system options for outgoing calls to set the system options for outgoing call service. Input data item no. Item input data description default related program 01 seizure trunk line mo...

  • Page 247

    Item no. Item input data description default related program 10 dial digits for toll restriction path 0 ~ 36 if this option is programmed with an entry other than 0, a call does not have a talk path unless the user di- als at least the number of digits en- tered in this option when placing an outgoi...

  • Page 248

    Item no. Item input data description default related program 21 hnpa exception type (v4.0 add- ed) 0 = toll 1 = local sets the exception of hnpa list. 0 21-01-20 21-01-22 21-26-01 21-27-01 21-28-01 22 10 digit local calls (v4.0 add- ed) 0 = 7 digits (without area code) 1 = 10 digits (with area code)...

  • Page 249

    Program 21 : outgoing call setup 21-02 : trunk group routing for extensions level: in description use program 21-02 : trunk group routing for extensions to assign program 14-06 routes to extensions. Input data extension number maximum eight digits day/night mode 1 ~ 8 item no. Item input data defaul...

  • Page 250

    Program 21 : outgoing call setup 21-03 : trunk group routing for trunks level: in description use program 21-03 : trunk group routing for trunks to set the trunk route table for automatic external call forward. The route table is set in program 14-06. Input data trunk port number 001 ~ 084 day/night...

  • Page 251

    Program 21 : outgoing call setup 21-04 : toll restriction class for extensions level: in description use program 21-04 : toll restriction class for extensions to assign a toll restriction class to an extension. The details of toll restriction are defined in program 21-05 and 21-06. A telephone and a...

  • Page 252

    Program 21 : outgoing call setup 21-05 : toll restriction class level: in description use program 21-05 : toll restriction class to set the system toll restriction classes (1 ~ 15). Input data toll restriction class number 1 ~ 15 item no. Item input data description default related program 01 intern...

  • Page 253

    Item no. Item input data description default related program 09 restriction for common speed dials 0 = does not restrict 1 = following restric- tion check use this option to enable/disable toll restriction for common speed dialing numbers. If enabled, system speed dialing numbers have the same restr...

  • Page 254

    Program 21 : outgoing call setup 21-06 : toll restriction table data setup level: in description use program 21-06 : toll restriction table data setup to set the system toll restriction data. Dial 1 ~ 9, 0, * , # can be entered in each table. Input data item no. Item table input data default 01 inte...

  • Page 255

    Item no. Item table input data default 07 deny restriction table this option lets you program the restrict code tables. If the system has toll restriction enabled, users cannot dial numbers listed in these ta- bles. There are four restrict code tables, with up to 60 entries in each table. The system...

  • Page 256

    Program 21 : outgoing call setup 21-07 : toll restriction override password setup level: sa description use program 21-07 : toll restriction override password setup to assign toll restriction override codes to extension ports. Each code must have four digits, using any combination of 0 ~ 9, # and * ...

  • Page 257: 21-08 : Repeat Dial Setup

    Program 21 : outgoing call setup 21-08 : repeat dial setup level: in description use program 21-08 : repeat dial setup to define the automatic repeat dial data. Input data item no. Item input data description default 01 repeat redial count 0 ~ 255 sets how many times a repeat redial au- tomatically ...

  • Page 258: 21-09 : Dial Block Setup

    Program 21 : outgoing call setup 21-09 : dial block setup level: in description use program 21-09 : dial block setup to define the dial blocking toll restriction class and dial block password to be used by the supervisor extension. Input data item no. Item input data description default 01 toll rest...

  • Page 259

    Program 21 : outgoing call setup 21-10 : dial block restriction class per extension level: in description use program 21-10 : dial block restriction class per extension to define the toll restriction class to each extension when the extension is set for dial block restriction. If this data is 0, tol...

  • Page 260

    Program 21 : outgoing call setup 21-11 : extension ringdown (hotline) assignment level: in description use program 21-11 : extension ringdown (hotline) assignment to define the hotline destination number for each extension number. Input data extension number maximum eight digits item no. Item input ...

  • Page 261

    Program 21 : outgoing call setup 21-12 : isdn calling party number setup for trunks level: in description use program 21-12 : isdn calling party number setup for trunks to assign calling party numbers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not ha...

  • Page 262

    Program 21 : outgoing call setup 21-13 : isdn calling party number setup for extensions level: in description use program 21-13 : isdn calling party number setup for extensions to assign each extension a calling party number (maximum 16 digits per entry). The calling number is the subscriber number ...

  • Page 263

    Program 21 : outgoing call setup 21-14 : walking toll restriction password setup level: sa description use program 21-14 : walking toll restriction password setup to assign the password and toll restriction class for walking toll restriction. Each code has six digits, using any combination of 0 ~ 9,...

  • Page 264

    Program 21 : outgoing call setup 21-15 : individual trunk group routing for extensions level: in description use program 21-15 : individual trunk group routing for extensions to designate the alternate trunk access route accessed when a user dials the alternate trunk route access code. Refer to prog...

  • Page 265

    Program 21 : outgoing call setup 21-16 : trunk group routing for networking level: in (this program is available for v1.5 or higher) description use program 21-16 : trunk group routing for networking to assign program 14-06 routes for a networked system. This is required to seize the trunk in a netw...

  • Page 266

    Program 21 : outgoing call setup 21-17 : ip trunk (sip) calling party number setup for trunk level: in description use program 21-17 : ip trunk (sip) calling party number setup for trunk set the sip calling party number for individual trunks. Input data trunk port number 001 ~ 084 item no. Item inpu...

  • Page 267: Extension

    Program 21 : outgoing call setup 21-19 : ip trunk (sip) calling party number setup for extension level: in description use program 21-19 : ip trunk (sip) calling party number setup for extension to set the sip calling party number for an individual extension. Input data extension number up to eight ...

  • Page 268

    Program 21 : outgoing call setup 21-20 : sip trunk call discernment setup for extension level: sb description use program 21-20 : sip trunk call discernment setup for extension to set the sip trunk call discernment. Input data extension number up to eight digits item no. Item input data default 01 d...

  • Page 269: Setting)

    Program 21 : outgoing call setup 21-21 : toll restriction for trunks (seized trunk basis setting) level: in description use program 21-21 : toll restriction for trunks (seized trunk basis setting) to define the toll restriction class to each trunk. The details of toll restriction are defined by prog...

  • Page 270

    Program 21 : outgoing call setup 21-22 : co message waiting indication - call back settings level: in description use program 21-22 : co message waiting indication - call back settings to define the settings of co message waiting indication. Input data trunk port number 001 ~ 084 item no. Item input...

  • Page 271: 21-26 : Home Npa Setup

    Program 21 : outgoing call setup 21-26 : home npa setup level: in (this program is available for v4.0 or higher) description use program 21-26 : home npa setup to set the home npa dial. Order to use this program prg 21-01-20 needs to set to 2: automatic call back. Input data index 1 ~ 16 item no. It...

  • Page 272

    Program 21 : outgoing call setup 21-27 : hnpa exceptions setup level: in (this program is available for v4.0 or higher) description use program 21-27 : hnpa exceptions setup to set the dial number sent. Order to use this program prg 21-01-20 needs to set as 2: automatic call back. Input data index 1...

  • Page 273

    Program 21 : outgoing call setup 21-28 : foreign npa locals setup level: in (this program is available for v4.0 or higher) description use program 21-28 : foreign npa locals setup to set the dial number sent. Order to use this program prg 21-01-20 needs to set as 2: automatic call back. Input data s...

  • Page 274

    Program 22 : incoming call setup 22-01 : system options for incoming calls level: in description use program 22-01 : system options for incoming calls to define the system options for incoming calls. Input data item no. Item input data description default related program 01 incoming call priority 0 ...

  • Page 275

    Item no. Item input data description default related program 11 vrs waiting message interval time 0 ~ 64800 seconds setup the sending duration time of the auto - attendant & queuing. The message is repeatedly sent out during the specified time. 20 22-14-06 22-15-06 41-11-06 12 mobile extension answe...

  • Page 276

    Program 22 : incoming call setup 22-02 : incoming call trunk setup level: in description use program 22-02 : incoming call trunk setup to assign the incoming trunk type for each trunk. There is one item for each night service mode. Input data trunk port number 001 ~ 084 day/night mode 1 ~ 8 item no....

  • Page 277

    Program 22 : incoming call setup 22-03 : trunk ring tone range level: in description use program 22-03 : trunk ring tone range to select the ring tone range for the trunk. The trunk uses a ring tone in the range selected when it rings an extension. Eight ring tones are available. Customize the trunk...

  • Page 278

    Incoming signal frequency pattern type frequency 1 frequency 2 modulation pattern 5 (v3.0 added) high middle low 1400hz 760hz 660hz 540hz 540hz 540hz 16hz 16hz 16hz pattern 6 (v3.0 added) high middle low 1400hz 760hz 660hz 540hz 540hz 540hz 8hz 8hz 8hz pattern 7 (v3.0 added) high middle low 2000hz 2...

  • Page 279

    Program 22 : incoming call setup 22-04 : incoming extension ring group assignment level: sa description use program 22-04 : incoming extension ring group assignment to assign extensions to ring groups. Calls ring extensions according to ring group programming. Use program 22-05 to assign trunks to r...

  • Page 280

    Program 22 : incoming call setup 22-05 : incoming trunk ring group assignment level: in description use program 22-05 : incoming trunk ring group assignment to assign trunks to incoming ring groups. There are 25 available ring groups. Input data trunk port number 001 ~ 084 day/night mode 1 ~ 8 item ...

  • Page 281

    Program 22 : incoming call setup 22-06 : normal incoming ring mode level: in description use program 22-06 : normal incoming ring mode to define whether or not an extension should ring for the normal incoming ring mode. Input data extension number maximum eight digits day/night mode 1 ~ 8 item no. I...

  • Page 282: 22-07 : Dil Assignment

    Program 22 : incoming call setup 22-07 : dil assignment level: in description use program 22-07 : dil assignment to assign the destination extension or department calling group for each dil incoming trunk. A dil rings an extension directly, without any other access map or ring group programming. If ...

  • Page 283

    Program 22 : incoming call setup 22-08 : dil/irg no answer destination level: in description for dil delayed ringing, use program 22-08 : dil/irg no answer destination to assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time expires (program 22-01-04). ...

  • Page 284: 22-09 : Did Basic Data Setup

    Program 22 : incoming call setup 22-09 : did basic data setup level: in description use program 22-09 : did basic data setup to define the basic setting of dial-in incoming calls for each trunk group. Input data trunk group number 01 ~ 25 item no. Item input data description default 01 expected numb...

  • Page 285

    Feature cross reference • direct inward dialing (did) issue 4.0 sl1100 programming manual 2-265 program 22.

  • Page 286

    Program 22 : incoming call setup 22-10 : did translation table setup level: in description use program 22-10 : did translation table setup to specify the size of the did translation tables. There are 800 (v1.5 or higher) translation table entries that you can allocate among 20 translation tables. In...

  • Page 287

    Program 22 : incoming call setup 22-11 : did translation number conversion level: sa description use program 22-11 : did translation number conversion to specify for each translation table entry (800). • the digits received by the system (eight maximum) • the extension the system dials after transla...

  • Page 288

    Item no. Item input data description default 01 received number maximum eight digits (0 ~ 9, * , #) this is the received did digits. No setting 02 target number maximum 36 digits (0 ~ 9, * , #, @) enter the destination number to which the did number is sent. No setting 03 did name maximum 12 charact...

  • Page 289

    Item no. Item input data description default 11 incoming ring group transfer 0 = disable (calls will not be routed to prg 22-12.) 1 = enable (calls will be routed to prg 22-12.) enable (1) or disable (0) each conversa- tion tables ability to follow the ring group programming defined in program 22-12...

  • Page 290

    Program 22 : incoming call setup 22-12 : did intercept ring group level: in description for each did translation table, use program 22-12 : did intercept ring group to define the first destination group for did calls. Depending on the entry in programs 22-09-02 and 22-11-04, the incoming calls route...

  • Page 291

    Program 22 : incoming call setup 22-13 : did trunk group to translation table assignment level: in description use program 22-13 : did trunk group to translation table assignment to assign the did trunk groups to did translation tables. Did trunks should be in their own group. If you have more than ...

  • Page 292

    Program 22 : incoming call setup 22-14 : vrs delayed message for irg level: in description use program 22-14 : vrs delayed message for irg (incoming group ring) to define for each incoming ring group the timers, vrs message number and type of tone for vrs waiting message. Input data incoming ring gr...

  • Page 293

    Program 22 : incoming call setup 22-15 : vrs delayed message for department group level: in description use program 22-15 : vrs delayed message for department group to define for each department (extension) group the timers, vrs message number and tone kind for vrs delayed message. There are 32 avai...

  • Page 294

    Program 22 : incoming call setup 22-16 : private call refuse target area setup level: in description use program 22-16 : private call refuse target area setup to define speed dial group number for private call refuse. Input data item no. Item input data description default 01 speed dial group number...

  • Page 295: Pattern

    Program 22 : incoming call setup 22-17 : dial-in conversion table area setup for time pattern level: sa description use program 22-17: dial-in conversion table area setup for time pattern to define time zone and dial-in conversion table (program 22-11) for time pattern. Input data conversion table n...

  • Page 296

    Program 22 : incoming call setup 22-18 : private call assignment setup level: in description use program 22-18: private call assignment setup to define assignment and incoming ring pattern for private calls. Input data item no. Item input data description default related program 01 transfer mode 0 =...

  • Page 297

    Program 22 : incoming call setup 22-20 : flexible ringing by caller id setup level: in description use program 22-20: flexible ringing by caller id setup to set flexible ringing by caller id per timer pattern mode. Input data trunk port number 001 ~ 084 day/night mode 01 ~ 08 item no. Item input dat...

  • Page 298: 23-02 : Call Pickup Groups

    Program 23 : answer features setup 23-02 : call pickup groups level: in description use program 23-02 : call pickup groups to assign extensions to call pickup groups. This program also lets you assign an extension call pickup group priority. If two extensions in a group are ringing at the same time,...

  • Page 299

    Program 23 : answer features setup 23-03 : universal answer/auto answer level: in description use program 23-03 : universal answer/auto answer to assign trunk routes (set in program 14-06) to extensions for universal answer. If the call ringing the paging system is in an extension assigned route, th...

  • Page 300

    Program 23 : answer features setup 23-04 : ringing line preference for virtual extensions level: in description use program 23-04 : ringing line preference for virtual extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. There are 50 ava...

  • Page 301

    Program 24 : hold/transfer setup 24-01 : system options for hold level: in description use program 24-01 : system options for hold to define the system options for the hold feature. Input data item no. Item input data description default related program 01 hold recall time 0 ~ 64800 seconds a call o...

  • Page 302

    Program 24 : hold/transfer setup 24-02 : system options for transfer level: in description use program 24-02 : system options for transfer to define the system options for the transfer feature. Input data item no. Item input data description default related program 01 busy transfer 0 = disable (no) ...

  • Page 303

    Item no. Item input data description default related program 09 two b-channel transfer retry timer 0 ~ 30 seconds 10 10-03-16 (pri) 10 disconnect trunk-to-trunk 0 ~ 64800 seconds 0 14-01-25 20-28-01 20-28-02 20-28-03 24-02-07 11 no answer step transfer 0 ~ 64800 seconds 10 14-01-26 12 no answer trun...

  • Page 304: 24-03 : Park Group

    Program 24 : hold/transfer setup 24-03 : park group level: in description use program 24-03 : park group to assign an extension to a park group. The system allows a total of 64 park groups. An extension user can pick up only a call parked in orbit by an extension user in own group. Input data extens...

  • Page 305

    Program 24 : hold/transfer setup 24-04 : automatic trunk-to-trunk transfer target setup level: in description use program 24-04 : automatic trunk-to-trunk transfer target setup to assign the speed dialing number bin which should be used as the destination of the automatic trunk-to-trunk transfer. In...

  • Page 306

    Program 24 : hold/transfer setup 24-05 : department group transfer target setup level: in description use program 24-05 : department group transfer target setup to assign the speed dialing bin which is used as the destination of the extension for the extension group. There are 32 available departmen...

  • Page 307

    Program 24 : hold/transfer setup 24-09 : call forward split settings level: in description use program 24-09 : call forward split settings to assign call forwarding type and the destination number for each extension/virtual extension. The destination can have up to 24 digits, using 0 ~ 9, * , #, and...

  • Page 308

    Feature cross reference • call forwarding, off-premise sl1100 issue 4.0 2-288 program 24 : hold/transfer setup program 24.

  • Page 309: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-01 : vrs/disa line basic data setup level: in description use program 25-01 : vrs/disa line basic data setup to define the basic setting of each vrs/ disa line. Input data trunk port number 001 ~ 084 item no. Item input data default related program 01 vrs/disa dial - i...

  • Page 310: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-02 : did/disa vrs message level: in description use program 25-02 : did/disa vrs message to assign the vrs message number to be used as the automated attendant message for each trunk which is assigned as a vrs/disa. Input data trunk port number 001 ~ 084 day/night mode...

  • Page 311: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-03 : vrs/disa transfer ring group with incorrect dialing level: in description use program 25-03 : vrs/disa transfer ring group with incorrect dialing to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial....

  • Page 312: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-04 : vrs/disa transfer ring group with no answer/ busy level: in description use program 25-04 : vrs/disa transfer ring group with no answer/busy to set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant calle...

  • Page 313: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-05 : vrs/disa error message assignment level: in description use program 25-05 : vrs/disa error message assignment to assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message ...

  • Page 314: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-06 : vrs/disa one-digit code attendant setup level: in description use program 25-06 : vrs/disa one-digit code attendant setup to set up single digit dialing through the vrs. This gives vrs callers single key access to extensions, the company operator, department calli...

  • Page 315

    Conditions • outside caller may not be able to dial individual extensions or lines if the same first digit is defined here. Feature cross reference • direct inward system access (disa) • voice response system (vrs) issue 4.0 sl1100 programming manual 2-295 program 25.

  • Page 316: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-07 : system timers for vrs/disa level: in description use program 25-07 : system timers for vrs/disa to set the value for the system timers which affect did and disa. Refer to the following chart for a description of each option, its range and default setting. Input da...

  • Page 317

    Item no. Item input data description default related program 09 disa internal paging time 0 ~ 64800 seconds this is the maximum length of an in- ternal page placed by a disa caller. If the page continues longer than this time, the system terminates the disa call. 30 seconds 20-31-21 10 disa external...

  • Page 318: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-08 : disa user id setup level: sa description use program 25-08 : disa user id setup to set the 6-digit disa password for each user. There are 15 users each with one 6-digit password. Input data disa user number 01 ~ 15 item no. Item input data default 01 password dial...

  • Page 319: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-09 : class of service for disa users level: in description use program 25-09 : class of service for disa users to set the disa class of service for each user. When a disa caller enters a password (defined in program 25-08), the system identifies the user and associates...

  • Page 320: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-10 : trunk group routing for disa level: in description use program 25-10 : trunk group routing for disa to assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. Enable or disable the dis...

  • Page 321: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-11 : disa toll restriction class level: in description for systems that use toll restriction, use program 25-11 : disa toll restriction class to assign a toll restriction class (1-15) to each disa user (1~15). The system uses the toll restriction class you enter in pro...

  • Page 322: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-12 : alternate trunk group routing for disa level: in description use program 25-12 : alternate trunk group routing for disa to define the trunk route selected when a disa caller dials the alternate trunk access code. The route selected is based on the disa caller clas...

  • Page 323: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-13 : system option for disa level: in description use program 25-13 : system option for disa to enter the password disa callers must dial before the system allows them to record, listen to and or erase the vrs messages. This program also is used to define additional di...

  • Page 324: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-15 : disa transfer target setup level: in description use program 25-15 : disa transfer target setup to assign a speed dial number when a dial tone times-out, or when the wrong number is received and the target extension does not answer or is busy. Input data trunk por...

  • Page 325: Program 26 : Ars Service

    Program 26 : ars service 26-01 : automatic route selection (ars/f-route) service level: in description use program 26-01 : automatic route selection service (ars/f-route) to define the system options for automatic route selection (ars/f-route). Input data item no. Item input data description default...

  • Page 326: Program 26 : Ars Service

    Program 26 : ars service 26-02 : dial analysis table for ars level: in description use program 26-02 : dial analysis table for ars to set pre-transaction tables for selecting automatic route selection (ars/f-route). • service type 1 (route to trunk group number) - the number routes to a trunk group....

  • Page 327: Program 26 : Ars Service

    Program 26 : ars service 26-03 : ars dial treatments level: in description use program 26-03 : ars dial treatments to assign the 15 dial treatments for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial treatment options are: • ...

  • Page 328: Program 26 : Ars Service

    Program 26 : ars service 26-04 : ars class of service level: in description use program 26-04 : ars class of service to set the ars class of service for an extension. Automatic route selection (ars/f-route) uses ars class of service when determining how to route extension calls. Input data extension...

  • Page 329: Program 26 : Ars Service

    Program 26 : ars service 26-11 : transit network id table level: in description use program 26-11 : transit network id table to define transit network id for alternate carrier access, which is referred from program 26-03. Input data transit network id table 1 ~ 4 item no. Item input data default 01 ...

  • Page 330: Program 26 : Ars Service

    Program 26 : ars service 26-12 : network specific parameter table for ars level: in description use program 26-12 : network specific parameter table for ars to define the network specific parameter table. Input data network specific parameter table 1 ~ 16 item no. Item input data description default...

  • Page 331

    Program 30 : dss/dls console setup 30-01 : dss console operating mode level: in description use program 30-01 : dss console operating mode to set the mode of the system dss consoles. The entry for this option applies to all the system dss consoles. The available options are: • regular (business) mod...

  • Page 332

    Program 30 : dss/dls console setup 30-02 : dss console extension assignment level: in description use program 30-02 : dss console extension assignment to identify which extensions have dss consoles connected. • up to 12 different extensions with dss consoles can be set up. A single extension can hav...

  • Page 333

    Program 30 : dss/dls console setup 30-03 : dss console key assignment level: sa description use program 30-03 : dss console key assignment to customize the key assignments for 60- button dss consoles. A dss console key can have any function with up to eight digits (e.G., extension number or service ...

  • Page 334

    Function number function additional data led indication note 07 conference key on (red) : conference operation 08 incoming call id list fast blink (red) : existing new cid on (red) : existing checked cid off : no cid 09 day/night mode switch mode number (1 ~ 8) on : while each mode 10 call forward -...

  • Page 335

    Function number function additional data led indication note 41 secretary buzzer extension number (8 digits) on (red) : calling party fast blink : called party 42 boss - secretary call pickup extension number (8 digits) on (red) : active 43 series call none 44 common hold none 45 exclusive hold none...

  • Page 336

    Function number function additional data led indication note 80 tandem ringing set up key 0 = cancel 1 = set extension number to tandem ring (8 dig- its) on (red) : master side slow blink (red) : slave side 81 automatic transfer to transfer key trunk line number 001 ~ 084 off : cancel slow blink (re...

  • Page 337

    Table 2-8 function number list [2] appearance function level ( * 00 - * 99) (service code 752) function number function additional data led indication * 01 trunk key trunk line number 001 ~ 084 fast blink (red) : incoming on (red) : speaking slow blink (red) : holding/ transferring/recall * 04 park ...

  • Page 338

    Program 30 : dss/dls console setup 30-04 : dss console alternate answer level: sa description use program 30-04 : dss console alternate answer to assign the alternate dss console station in case off-duty mode is set (by pressing the alt key on the dss console). Input data index 1 dss console number ...

  • Page 339

    Program 30 : dss/dls console setup 30-05 : dss console lamp table level: in description use program 30-05 : dss console lamp table to define the led patterns for functions on the dss consoles. Input data item no. Item input data default 01 idle extension 0 ~ 7 (lamp pattern data) 0 02 busy extension...

  • Page 340

    L e d p a tte rn 0 :[o f f ] l e d p a tte rn 1 :[f l : o n (5 0 0 m s)/off(5 0 0 m s)] o n o ff o n o ff l e d p a tte rn 2 :[w k : o n (2 5 0 m s)/off(2 5 0 m s)] o n o ff l e d p a tte rn 3 :[r w : o n (1 2 5 m s)/off(1 2 5 m s)] o n o ff l e d p a tte rn 4 :[ir : o n (1 2 5 m s)/off(1 2 5 m s)/ ...

  • Page 341: Program 31 : Paging Setup

    Program 31 : paging setup 31-01 : system options for internal/external paging level: in description use program 31-01 : system options for internal/external paging to define the system options for internal/external paging. The system shows the name you program on the telephone display. Use the follo...

  • Page 342

    Item no. Item input data description default related program 04 privacy release time 0 ~ 64800 seconds once the user initiates a meet-me conference or voice call confer- ence, the system waits this time for the paged party to join the call. 90 seconds conditions none feature cross reference • paging...

  • Page 343: Program 31 : Paging Setup

    Program 31 : paging setup 31-02 : internal paging group assignment level: in description use program 31-02 : internal paging group assignment to assign extensions to internal paging groups (i.E., page zones). The setting in this program also determines if the internal page group can receive internal...

  • Page 344: Program 31 : Paging Setup

    Program 31 : paging setup 31-03 : internal paging group settings level: in description use program 31-03 : internal paging group settings to assign names to internal paging groups (i.E., page zones) and to define the splash tone for internal paging. The system shows the names you program on the tele...

  • Page 345

    Default item 01 : internal paging group name extension paging group name 01 group 1 02 group 2 : : 32 group 32 conditions none feature cross reference • paging, internal issue 4.0 sl1100 programming manual 2-325 program 31.

  • Page 346: Program 31 : Paging Setup

    Program 31 : paging setup 31-04 : external paging zone group level: in description use program 31-04 : external paging zone group to assign each external paging zone to an external paging group. Users call the external paging group when broadcasting announcements to the external zone. To simplify pr...

  • Page 347: Program 31 : Paging Setup

    Program 31 : paging setup 31-05 : universal night answer/ring over page level: in description use program 31-05 : universal night answer/ring over page to assign universal night answer ringing to each external paging zone. For each trunk port, make a separate entry for each external paging zone. For...

  • Page 348: Program 31 : Paging Setup

    Program 31 : paging setup 31-06 : external speaker control level: in description use program 31-06 : external speaker control to define the settings for the external speaker using an amplifier. Input data external speaker number 1 ~ 3 item no. Item input data description default 01 broadcast splash ...

  • Page 349: Program 31 : Paging Setup

    Program 31 : paging setup 31-07 : combined paging assignments level: in description use program 31-07 : combined paging assignments to assign an external paging group (0 ~ 3) to an internal paging zone (0 ~ 32) for combined paging. When an extension user makes a combined page, they simultaneously br...

  • Page 350: Program 31 : Paging Setup

    Program 31 : paging setup 31-08 : bgm on external paging level: in description use program 31-08 : bgm on external paging to set the background music option for each external paging zone. If enabled, the system plays background music over the zone when it is idle. Input data external speaker number ...

  • Page 351: Program 31 : Paging Setup

    Program 31 : paging setup 31-10 : external paging group basic setting level: in description use program 31-10 : external paging group basic setting assigns the name of external paging group and defines the splash tone for external paging. Input data external speaker number 01 ~ 03 item no. Item inpu...

  • Page 352

    Program 32 : door box and sensor setup 32-01 : door box timers setup level: in description use program 32-01 : door box timers setup to assign the timers used for the door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data item no. I...

  • Page 353

    Program 32 : door box and sensor setup 32-02 : door box ring assignment level: sa description use program 32-02 : door box ring assignment to assign the extension which rings when a caller presses the associated door box call button. The door box feature is called door phone when programming via web...

  • Page 354: 32-03 : Door Box Basic Setup

    Program 32 : door box and sensor setup 32-03 : door box basic setup level: in description use program 32-03 : door box basic setup to select the chime pattern and gain level for each door box. There are six distinctive chime patterns. The chime tones are defined in 80-01 : service tone setup. On pag...

  • Page 355: 32-04 : Door Box Name Setup

    Program 32 : door box and sensor setup 32-04 : door box name setup level: in description use program 32-04 : door box name setup to define the name of each door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data door box number 1 ~ 6...

  • Page 356: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-01 : e&m tie line basic setup level: in description use program 34-01 : e&m tie line basic setup to define the basic settings for each e&m tie line. Input data trunk port number 001 ~ 084 item no. Item input data description default related program 01 did/e&m start sig...

  • Page 357: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-02 : e&m tie line class of service level: in description use program 34-02 : e&m tie line class of service to assign a class of service to a tie line (there are 15 tie line classes of service). The class of service options are defined in program 20-14. For each tie lin...

  • Page 358: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-03 : trunk group routing for e&m tie lines level: in description use program 34-03 : trunk group routing for e&m tie lines to assign the trunk group route 01 ~ 25) chosen when a user seizes a tie line and dials 9. (set trunk group routing in program 14-07.) if the syst...

  • Page 359: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-04 : e&m tie line toll restriction class level: in description use program 34-04 : e&m tie line toll restriction class to enter a toll restriction class for each tie line. There are 15 toll restriction classes which are defined in programs 21-05 and 21-06. For each tie...

  • Page 360: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-05 : tie line outgoing call restriction level: in description use program 34-05 : tie line outgoing call restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.G., dialed from a tie line). For each inbound trunk group, enable...

  • Page 361: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-06 : add/delete digit for e&m tie line level: in description use program 34-06 : add/delete digit for e&m tie line to set digits that the system should add or delete for tie lines. • delete digit some tie line networks pass the location number and extension number to t...

  • Page 362: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-07 : e&m tie line timer level: in description use program 34-07 : e&m tie line timer to define the system service tone timers. Input data item no. Item input data default 01 first digit pause (e&m immediate start) 0 ~ 64800 seconds 3 seconds 02 first digit pause (e&m w...

  • Page 363: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-08 : toll restriction data for e&m tie lines level: in description use program 34-08 : toll restriction data for e&m tie lines to define the toll restriction data for e&m tie lines. This data should be defined if tie line toll restriction is enabled in program 21-05-13...

  • Page 364: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-09 : ani/dnis service options level: in description use program 34-09 : ani/dnis service options to define the ani/dnis service option setup for e&m class of service. Input data class of service 01 ~ 15 item no. Item input data description default related program 01 re...

  • Page 365

    Item no. Item input data description default related program 04 route table set- up of target dial 0 = spd table (program 13-03) 1 = did table (program 22-11) the option sets how the system uses the route data (gathered in item 3) to route incoming ani/dnis calls. If option 2 is selected, and the ca...

  • Page 366

    Item no. Item input data description default related program 09 calling number address length 1 ~ 8 when item 01 = 0 (ani/dnis re- ceive format is the address), use this option to specify the address length. The choices are from 1 ~ 8 digits. Cos 01 = 7 cos 02 ~ 15 = 7 34-09-01 conditions none featu...

  • Page 367: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-10 : digit delete for t1 ani level: in description use program 34-10 : digit delete for t1 ani to delete the information digits received from the network on feature group d trunks. Input data incoming trunk group number 001 ~ 025 item no. Item input data description de...

  • Page 368: 35-01 : Smdr Options

    Program 35 : smdr account code setup 35-01 : smdr options level: in description use program 35-01 : smdr options to set the smdr (station message detail recording) options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range and default setting. ...

  • Page 369

    Feature cross reference • station message detail recording issue 4.0 sl1100 programming manual 2-349 program 35.

  • Page 370: 35-02 : Smdr Output Options

    Program 35 : smdr account code setup 35-02 : smdr output options level: in description use program 35-02 : smdr output options to set the smdr (station message detail recording) output options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range ...

  • Page 371

    Item no. Item input data description default 13 cli output when did to trunk 0 = not displayed 1 = displayed determine if the cli output should be dis- played for did. 0 14 date 0 = not displayed 1 = displayed determine whether or not the date should be displayed on smdr reports. This option must be...

  • Page 372

    Feature cross reference • station message detail recording sl1100 issue 4.0 2-352 program 35 : smdr account code setup program 35.

  • Page 373

    Program 35 : smdr account code setup 35-03 : smdr port assignment for trunk group level: in description use program 35-03 : smdr port assignment for trunk group to assign the smdr port for each trunk group. For each trunk group, select the smdr port where the incoming smdr information should be sent...

  • Page 374

    Program 35 : smdr account code setup 35-04 : smdr port assignment for department groups level: in description use program 35-04 : smdr port assignment for department groups to assign the smdr port for each department group. For each department group, select the smdr port where the outgoing smdr info...

  • Page 375: 35-05 : Account Code Setup

    Program 35 : smdr account code setup 35-05 : account code setup level: in description use program 35-05 : account code setup to set various account code options for an extension class of service. Assign a class of service to extensions in program 20-06. Input data class of service number 01 ~ 15 ite...

  • Page 376

    Feature cross reference • account code forced/verified/unverified sl1100 issue 4.0 2-356 program 35 : smdr account code setup program 35.

  • Page 377

    Program 35 : smdr account code setup 35-06 : verified account code table level: in description use program 35-06 : verified account code table to enter account codes into the verified account code list. You can enter up to 800 codes with 1 ~ 16 digits, using the characters 0 ~ 9 or #. Use the lk1 to...

  • Page 378

    Program 40 : voice recording system 40-01 : voice mail basic setup level: in description use program 40-01 : voice mail basic setup to set the basic setting of voice mail. Input data item no. Item input data default 01 fixed channel for voice mail 0 ~ 16 0 02 time stamp 0 = disable 1 = enable 1 03 c...

  • Page 379

    Program 40 : voice recording system 40-07 : voice prompt language assignment for vrs level: in description use program 40-07 : voice prompt language assignment for vrs to specify the language to be used for the vrs prompts. Input data item no. Item input data default 01 voice prompt language assign-...

  • Page 380

    Program 40 : voice recording system 40-10 : voice announcement service option level: in description in program 40-10 : voice announcement service option define the system options for the voice announcement feature. Input data item no. Item input data description default related program 01 vrs fixed ...

  • Page 381

    Item no. Item input data description default related program 09 call attendant no answer mes- sage 0 ~ 100 (0 = no message) 0 15-01-09 10 call forward re- mainder an- nouncement (v2.0 added) 0 = do not play 1 = play flag that control the playback of the vrs announcements for 'on the for- warded phon...

  • Page 382

    Program 40 : voice recording system 40-11 : preamble message assignment level: in description in program 40-11 : preamble message assignment to assign the vrs message number to be used as the preamble message for each trunk. When the extension user answers the incoming call, the assigned vrs message...

  • Page 383: Program 41 : Acd Setup

    Program 41 : acd setup 41-01 : system options for acd level: in (this program is available for v4.0 or higher) description in program 41-01 : system options for acd define the system options for the acd feature. Input data item no. Item input data default 03 acd mis connection ports 0 = none 3 = lan...

  • Page 384: Program 41 : Acd Setup

    Program 41 : acd setup 41-02 : acd group and agent assignments level: sa (this program is available for v1.5 or higher) description in program 41-02 : acd group and agent assignments, to set the name of abbreviated dial group name. For each acd extension number, assign an acd group (01 ~ 02). An acd...

  • Page 385: Program 41 : Acd Setup

    Program 41 : acd setup 41-03 : incoming ring group assignment for acd group level: sa (this program is available for v1.5 or higher) description in program 41-03 : incoming ring group assignment for acd group for each incoming trunk group set up in program 22-05, designate which acd group (01 ~ 02) ...

  • Page 386: Program 41 : Acd Setup

    Program 41 : acd setup 41-05 : acd agent work schedules level: sa (this program is available for v1.5 or higher) description use program 41-05 : acd agent work schedules to set up the work schedules for acd agents and groups. For each acd work schedule (1~4), designate the start and stop times for e...

  • Page 387: Program 41 : Acd Setup

    Program 41 : acd setup 41-06 : trunk work schedules level: sa (this program is available for v1.5 or higher) description use program 41-06 : trunk work schedules to set up the work schedules for trunks. For each work schedule (1 ~ 4), designate the start and stop times for each of the eight work per...

  • Page 388: Program 41 : Acd Setup

    Program 41 : acd setup 41-07 : acd weekly schedule setup level: sa (this program is available for v1.5 or higher) description use program 41-07 : acd weekly schedule setup to assign the four work schedules (1 ~ 4) to days of the week. The assignments you make in this program apply to both the acd ag...

  • Page 389: Program 41 : Acd Setup

    Program 41 : acd setup 41-08 : acd overflow options level: sa (this program is available for v1.5 or higher) description for each acd group (01 ~ 02), use program 41-08 : acd overflow options to assign the overflow mode (0~9), destination and announcement message types. Delay announcement functions ...

  • Page 390

    Item no. Item input data description default 04 acd overflow trans- fer time 0 ~ 64800 (seconds) define the time before acd overflow oc- curs. Each acd group can have unique overflow options. 30 05 system speed dial bin 0 ~ 999 (used when 41-08-02 is set to 5) assign the speed dial bin to be used as...

  • Page 391: Program 41 : Acd Setup

    Program 41 : acd setup 41-09 : acd overflow table setting level: sa (this program is available for v1.5 or higher) description use program 41-09 : acd overflow table setting to define the acd group to which a call is transferred when overflow occurs. Input data acd group no. 01 ~ 02 item no. Item in...

  • Page 392: Program 41 : Acd Setup

    Program 41 : acd setup 41-11 : vrs delay announcement level: sa (this program is available for v1.5 or higher) description use program 41-11 : vrs delay announcement to assign the vrs message number to use as the message source for the 1st and 2nd delay announcement messages. Refer to program 41-08 ...

  • Page 393

    Feature cross reference • automatic call distribution (acd) issue 4.0 sl1100 programming manual 2-373 program 41.

  • Page 394: Program 41 : Acd Setup

    Program 41 : acd setup 41-12 : night announcement setup level: sa (this program is available for v1.5 or higher) description use program 41-12 : night announcement setup to set night announce time for each acd group. Night announcement availability depends on the setting in program 41-03-02. The nig...

  • Page 395: Program 41 : Acd Setup

    Program 41 : acd setup 41-13 : vrs message number for night announcement level: sa (this program is available for v1.5 or higher) description use program 41-13 : vrs message number for night announcement to define the vrs message number to use as the night announcement. This program is activated whe...

  • Page 396: Program 41 : Acd Setup

    Program 41 : acd setup 41-14 : acd options setup level: sa (this program is available for v1.5 or higher) description use program 41-14 : acd options setup to set various options for acd groups. When you set an option for an acd group, the setting is in force (if applicable) for all agents in the gr...

  • Page 397

    Item no. Item input data description default 17 cti : operation mode when transfer no log- in acd groups 0 = transfer to acd group 1 = error notice this program allows cti server transfers a trunk call to acd pilot number which group has no login agent in 3rd party cti. 0 conditions none feature cro...

  • Page 398: Program 41 : Acd Setup

    Program 41 : acd setup 41-16 : acd threshold overflow level: sa (this program is available for v1.5 or higher) description use program 41-16 : acd threshold overflow to define the value of the acd threshold call overflow and the mode for each acd group. Input data acd group no. 01 ~ 02 item no. Item...

  • Page 399: Program 41 : Acd Setup

    Program 41 : acd setup 41-19 : acd voice mail delay announcement level: sa (this program is available for v1.5 or higher) description use program 41-19 : acd voice mail delay announcement to assign inmail master mailboxes (program 47-03) as acd delay announcement mailboxes. Input data acd group numb...

  • Page 400: Program 41 : Acd Setup

    Program 41 : acd setup 41-20 : acd queue display settings level: sa (this program is available for v1.5 or higher) description use program 41-20 : acd queue display settings to assign the options for the acd queue status display feature. This program allows the queue status display, and causes an al...

  • Page 401: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-01 : system options for hotel/motel level: in description use program 42-01 : system options for hotel/motel to assign the system options for hotel/motel service. Input data item no. Item input data description default 01 answering message mode for wake up call (hotel mod...

  • Page 402: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-02 : hotel/motel telephone setup level: in description use program 42-02 : hotel/motel telephone setup to define the basic operation of the hotel/motel extensions. Input data extension number up to eight digits item no. Item input data description default 01 hotel mode 0 ...

  • Page 403: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-03 : class of service options (hotel/motel) level: in description use program 42-03 : class of service options (hotel/motel) to set the hotel/motel class of service (cos) options. Assign class of service to extensions in program 42-02 : hotel/motel telephone setup. There ...

  • Page 404

    Feature cross reference • class of service • hotel/motel sl1100 issue 4.0 2-384 program 42 : hotel setup program 42.

  • Page 405: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-04 : hotel mode one-digit service codes level: in description use program 42-04 : hotel mode one-digit service codes to set up the hotel mode one-digit service codes which are assigned in 42-02-01. For each department calling group (01 ~ 32), you enter the destination for...

  • Page 406: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-05 : hotel room status printer level: in description use program 42-05 : hotel room status printer to set the lan port to output the hotel data (check-out sheet, room status, etc.) and the output options for the hotel/ motel feature. Input data item no. Item input data de...

  • Page 407: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-09 : flexible setup for room status level: in (this program is available for v2.0 or higher) description use program 42-09 : flexible setup for room status to enable dial room status codes. Note the code definitions only apply to the system itself. Input data room status ...

  • Page 408

    Program 44 : ars/f-route setup 44-01 : system options for ars/f-route level: in description use program 44-01 : system options for ars/f-route to define the system options for the ars/f- route feature. Input data item no. Item input data description default 01 ars/f-route time schedule 0 = not used ...

  • Page 409

    Program 44 : ars/f-route setup 44-02 : dial analysis table for ars/f-route access level: in description use program 44-02 : dial analysis table for ars/f-route access to set the pre-transaction table for selecting ars/f-route. Input data dial analysis table number 001 ~ 120 item no. Item input data ...

  • Page 410

    Item no. Item input data description default 04 dial tone simulation 0 = off 1 = on if enabled, this option sends dial tone to the calling party after the routing is deter- mined. This may be required if the central office at the destination does not send dial tone. 0 conditions none feature cross r...

  • Page 411

    Program 44 : ars/f-route setup 44-03 : dial analysis extension table level: in description when program 44-02-02 is set to type 3, use program 44-03 : dial analysis extension table to set the dial extension analysis table. These tables are used when the analyzed digits must be more than eight digits...

  • Page 412

    Conditions none feature cross reference • automatic route selection (ars/f-route) sl1100 issue 4.0 2-392 program 44 : ars/f-route setup program 44.

  • Page 413

    Program 44 : ars/f-route setup 44-04 : ars/f-route selection for time schedule level: in description use program 44-04 : ars/f-route selection for time schedule to assign each ars/ f-route selection number to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for ...

  • Page 414: 44-05 : Ars/f-Route Table

    Program 44 : ars/f-route setup 44-05 : ars/f-route table level: in description use program 44-05 : ars/f-route table to set the ars/f-route table. There are four kinds of order. If the higher priority trunk groups are busy, the next order group is used. If a lower priority route is selected, the cal...

  • Page 415

    Conditions none feature cross reference • automatic route selection (ars/f-route) issue 4.0 sl1100 programming manual 2-395 program 44.

  • Page 416

    Program 44 : ars/f-route setup 44-06 : additional dial table level: in description use program 44-06 : additional dial table to set the additional dial table to add prior to the dialed ars/f-route number. The additional dial table used is determined in program 44-05-03. Input data additional dial ta...

  • Page 417

    Program 44 : ars/f-route setup 44-07 : gain table for ars/f-route access level: in description use program 44-07 : gain table for ars/f-route access to set the gain/pad table. If an extension dials ars/f-route number: • the extension dial gain table, assigned in program 44-05, is activated. • the ex...

  • Page 418

    Program 44 : ars/f-route setup 44-08 : time schedule for ars/f-route level: in description use program 44-08 : time schedule for ars/f-route to define the daily pattern of the ars/f- route feature. Ars/f-route has 10 time patterns. These patterns are used in programs 44-09 and 44-10. The daily patte...

  • Page 419

    Feature cross reference • automatic route selection (ars/f-route) issue 4.0 sl1100 programming manual 2-399 program 44.

  • Page 420

    Program 44 : ars/f-route setup 44-09 : weekly schedule for ars/f-route level: in description use program 44-09 : weekly schedule for ars/f-route to define a weekly schedule for using ars/f-route. The pattern number is defined in program 44-08-01. Input data day number 1 = sunday 2 = monday 3 = tuesd...

  • Page 421

    Program 44 : ars/f-route setup 44-10 : holiday schedule for ars/f-route level: in description use program 44-10 : holiday schedule for ars/f-route to define a yearly schedule for ars/f- route. This schedule is used for setting special days such as national holidays. The pattern number is defined in ...

  • Page 422

    Program 45 : voice mail integration 45-01 : voice mail integration options level: in description use program 45-01 : voice mail integration options to customize certain voice mail integration options. Input data item no. Item input data description default related program 01 voice mail de- partment ...

  • Page 423

    Item no. Item input data description default related program 10 new nsl proto- col support 0 = off (disable) 1 = on (enable) 0 11 prefix for call screening dial (one digit) 1 45-01-03 12 prefix for park and page dial (one digit) * 45-01-04 13 prefix for mes- sage wait dial (one digit) # 45-01-05 15 ...

  • Page 424: 45-02 : Nsl Option Setup

    Program 45 : voice mail integration 45-02 : nsl option setup level: sa description use program 45-02 : nsl option setup to setup the nsl options for voice mail integration. Input data item no. Item input data default 01 send dtmf tone or 6kd message 0 = send dtmf tone to slt-vm port 1 = send 6kd mes...

  • Page 425

    Program 45 : voice mail integration 45-04 : voice mail digit add assignment level: in description use program 45-04 : voice mail digit add assignment to define the digits to add. Input data item no. Item input data default related program 01 remote logon (internal) up to four digits no setting 45-01...

  • Page 426: Digits

    Program 45 : voice mail integration 45-05 : voice mail send protocol signal without additional digits level: in description use program 45-05 : voice mail send protocol signal without additional digits to send trunk number and/or station number information if integrating to voice mail when program 4...

  • Page 427: Program 47 : Inmail

    Program 47 : inmail 47-01 : inmail system options level: in description use program 47-01 : inmail system options to set up the inmail system-wide options. Input data item no. Item input data description default 02 inmail master name up to 12 characters (mastername) the cpu must be reset for a chang...

  • Page 428

    Item no. Item input data description default 05 message backup/go ahead time 1 ~ 6015 seconds (msg bkup/adv time) use this option to set the backup/ go ahead time. This time sets how far inmail backs up when a user dials b while listen- ing to a message. This interval also sets how far inmail jumps ...

  • Page 429

    Item no. Item input data description default 10 wait between non- pager callout at- tempts 1 ~ 255 minutes (notify n-pgr intvl) use this option to set the minimum time (1 ~ 255 minutes) between non-pager mes- sage notification callouts in which the des- tination answers, says hello, dials 1 to ac- k...

  • Page 430

    Item no. Item input data description default 17 inmail port 0 ~ 113 (v3.5 changed) (can only use the port numbers provided in the description section.) when using v3.5 or higher software the in- mail can be assigned to ports 113-128 and will not affect the total station and trunk ports. In addition ...

  • Page 431: Program 47 : Inmail

    Program 47 : inmail 47-02 : inmail station mailbox options level: in description use program 47-02 : inmail station mailbox options to set up a station/extension mailbox. Station mailboxes are automatically assigned as subscriber mailboxes. Normally, inmail station mailbox numbers 1 ~ 64 should corr...

  • Page 432

    Item no. Item input data description default 05 auto erase/save of messages 0 = erase after the subscriber lis- tens to the entire new message and hangs up, inmail erases the mes- sage. 1 = save after the subscriber lis- tens to the entire new message and hangs up, inmail saves the mes- sage. Use th...

  • Page 433

    Item no. Item input data description default 10 forced unscreened transfer 0 = no (disabled) 1 = yes (enabled) (forced utrf) use this option to enable or disable auto- mated attendant forced unscreened transfer for the subscriber mailbox. If ena- bled, each screened transfer (trf) to the extension i...

  • Page 434

    Item no. Item input data description default 24 all find-me follow- me enabled 0 = no 1 = yes 0 25 security code option 0 = always 1 = remote logon only 0 26 auto play (v1.5 add- ed) 0 = disabled 1 = enable 0 27 email message save/ delete option (v1.5 added) 0 = no change 1 = save 2 = delete 0 28 qu...

  • Page 435: Program 47 : Inmail

    Program 47 : inmail 47-03 : inmail group mailbox options level: in description use program 47-03 : inmail group mailbox options to set up the 32 group mailboxes (01 ~ 32). A group mailbox is used for department group overflow and can be a subscriber or call routing. Input data group mailbox number 0...

  • Page 436: Program 47 : Inmail

    Program 47 : inmail 47-06 : group mailbox subscriber options level: in description use program 47-06 : group mailbox subscriber options to set up a master mailbox assigned as a subscriber mailbox in 47-03-03 : master mailbox type. Input data group mailbox number 01 ~ 32 item no. Item input data desc...

  • Page 437

    Item no. Item input data description default 05 recording conversa- tion beep 0 = no (disabled) 1 = yes (enabled) (rec conv beep) use this option to enable or disable the conversation record beep. If enabled, all parties on a call hear the voice prompt “recording”, followed by a single beep when the...

  • Page 438

    Item no. Item input data description default 11 dialing option 0 = no (disabled) 1 = yes (enabled) dialing option provides additional dialing options for next call routing mailbox calls (see next call routing mailbox below). If enabled, a caller who accesses the sub- scriber mailbox to leave a messa...

  • Page 439

    Table 2-10 47-06-14 default table item name input data 47-06-14 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 440: Program 47 : Inmail

    Program 47 : inmail 47-07 : inmail routing mailbox options level: in description use program 47-07 : inmail routing mailbox options to set up the 32 routing mailboxes. Routing mailboxes can be either announcement or call routing mailboxes. Input data routing mailbox number 01 ~ 32 item no. Item inpu...

  • Page 441

    Table 2-11 47-07-03 default table item name input data 47-07-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 442: Program 47 : Inmail

    Program 47 : inmail 47-08 : call routing mailbox options level: in description use program 47-08 : call routing mailbox options to set the options for mailboxes assigned as call routing mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data d...

  • Page 443

    Conditions none feature cross reference none issue 4.0 sl1100 programming manual 2-423 program 47.

  • Page 444: Program 47 : Inmail

    Program 47 : inmail 47-09 : announcement mailbox options level: in description use program 47-09 : announcement mailbox options to set the options for mailboxes assigned as announcement mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data d...

  • Page 445

    Feature cross reference none issue 4.0 sl1100 programming manual 2-425 program 47.

  • Page 446: Program 47 : Inmail

    Program 47 : inmail 47-10 : inmail trunk options level: in description use program 47-10 : inmail trunk options to assign inmail options for each trunk. Currently, only 47-10-01 : answer table assignment is available. Input data trunk port number 001 ~ 084 item no. Item input data description defaul...

  • Page 447

    Table 2-12 47-10-03 default table item name input data 47-10-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 448: Program 47 : Inmail

    Program 47 : inmail 47-11 : inmail answer table options level: in description use program 47-11 : inmail answer table options to set options for the answer tables. Inmail provides eight answer tables (1 ~ 16 (v3.0 higher) ). To set up the schedules for each answer table, go to 47-12 : inmail answer ...

  • Page 449

    Item no. Item input data description default 02 override mailbox category (over- ride mb ctg) use this option to specify the category of the mailbox where automated at- tendant calls should route when you enable answer schedule override. • if the override mailbox is a sub- scriber mailbox, the outsi...

  • Page 450

    Item no. Item input data description default 03 default mailbox category(default mb ctg) use this option to specify the category of mailbox used as the default mail- box. • if the default mailbox is a sub- scriber mailbox, the outside caller hears the mailbox greeting (if recor- ded) and can leave a...

  • Page 451: Program 47 : Inmail

    Program 47 : inmail 47-12 : inmail answer schedules level: in description use program 47-12 : inmail answer schedules to set up the inmail automated attendant answer schedules. There are 16 (v3.5 or higher) answer tables, with up to 10 answer schedules in each answer table. Input data answer table n...

  • Page 452

    Item no. Item input data default description 01 schedule type 0 = undefined 1 = day of the week 2 = range of days 3 = date answer table 1/ schedule 1 = 2 all other schedules = 0 (entryxx schedule type) use this option to assign a sched- ule type to the selected answer schedule. The schedule type de-...

  • Page 453

    Item no. Item input data default description 02 answering mailbox catego- ry (entryxx mb ctg) use this option to specify the category of mailbox to which automated attendant calls should route when the sched- ule is in effect. If the answering mailbox is a subscriber mailbox, the out- side caller he...

  • Page 454

    Item no. Item input data default description 06 date (entryxx date) for date (type 3) answer schedules, use this option to select the date the answer schedule should be active. Mmdd for example : - 0101 = january 1 - 1231 = december 31 (0000 = undefined) all schedule = 0000 07 schedule start time (e...

  • Page 455: Program 47 : Inmail

    Program 47 : inmail 47-13 : inmail dial action tables level: in description use program 47-13 : inmail dial action tables to set up the inmail dial action tables. The dial action table defines the options than an automated attendant caller can dial. A dial action table is associated with a call rout...

  • Page 456

    Item no. Name input data description 01 action 0 = und (undefined) 1 = trf (transfer) 2 = utrf (unscreened transfer) 3 = rec1 4 = rec2 5 = logon 6 = hang up 7 = goto • trf action - screened transfer (1) (trf) • utrf action - unscreened transfer (2) (utrf) • rec1 action - quick message with greeting ...

  • Page 457

    Dial action table default settings key dial action table 1 dial action table 2 ~ 16 action data action data 7 0 (und) 0 0 (und) 0 8 0 (und) 0 0 (und) 0 9 6 (hang up) 0 0 (und) 0 0 2 (utrf) 101 0 (und) 0 * 3 (rec1) ixxx 0 (und) 0 # 5 (logon) ixxx 0 (und) 0 timeout 2 (utrf) 101 0 (und) 0 timeout provi...

  • Page 458: Program 47 : Inmail

    Program 47 : inmail 47-15 : routing directory mailbox options level: in description use program 47-15 : routing directory mailbox options to define the routing directory mailbox options. This data is referred if program 47-07-02 (routing master mailbox type) was set to type 4 (directory). Input data...

  • Page 459: Program 47 : Inmail

    Program 47 : inmail 47-17 : routing distribution mailbox options level: in description use program 47-17 : routing distribution mailbox options to assign data when program 47-07-02 is set to 4 (distribution). Input data routing mailbox number 01 ~ 32 entry number 01 ~ 20 item no. Item input data des...

  • Page 460: Program 47 : Inmail

    Program 47 : inmail 47-18 : smtp setup level: in description use program 47-18 : smtp setup to set the snmp e-mail notification. Input data item no. Item input data default 01 smtp enabled 0 = no 1 = yes 0 02 server name up to 48 characters no setting 03 smtp port 0 ~ 65535 25 04 encryption 0 = no 1...

  • Page 461: Program 47 : Inmail

    Program 47 : inmail 47-19 : pop3 setup level: in description use program 47-19 : pop3 setup to set the inmail e-mail notification. Input data item no. Item input data default 01 server name up to 48 characters no setting 02 pop3 port 0 ~ 65535 110 03 encryption 0 = no 1 = yes 0 04 user name up to 48...

  • Page 462: Program 47 : Inmail

    Program 47 : inmail 47-20 : station mailbox message notification options level: in description use program 47-20 : station mailbox message notification options to define the intramail station mailbox message notification options. Input data station mailbox number 001 ~ 128 (v3.5 changed) index numbe...

  • Page 463

    Conditions none feature cross reference none issue 4.0 sl1100 programming manual 2-443 program 47.

  • Page 464: Program 47 : Inmail

    Program 47 : inmail 47-21 : station mailbox find-me follow-me options level: in description use program 47-21 : station mailbox find-me follow-me options to define the intramail station mailbox find-me follow-me options. Input data station mailbox number 001 ~ 128 (v3.5 changed) index number 1 ~ 3 i...

  • Page 465: Program 47 : Inmail

    Program 47 : inmail 47-22 : group mailbox message notification options level: in description use program 47-22 : group mailbox message notification options to define the intramail group mailbox message notification options. Input data group mailbox number 01 ~ 32 index number 1 ~ 5 item no. Item inp...

  • Page 466

    Conditions none feature cross reference none sl1100 issue 4.0 2-446 program 47 : inmail program 47.

  • Page 467: Program 47 : Inmail

    Program 47 : inmail 47-23 : group mailbox find-me follow-me options level: in description use program 47-23 : group mailbox find-me follow-me options to define the intramail group mailbox find-me follow-me options. Input data group mailbox number 01 ~ 32 index number 1 ~ 3 item no. Item input data d...

  • Page 468: 80-01 : Service Tone Setup

    Program 80 : basic hardware setup for system 80-01 : service tone setup level: in description use program 80-01 : service tone setup to define up to 64 service tones. Each service tone is defined by the combination of 32 basic tones. Input data service tone number 01 ~ 64 item no. Item input data de...

  • Page 469

    Basic tone no. Frequency (hz) level (db) 15 650 / 780 -19 / -13 16 780 / 1040 -19 / -13 17 520 / 650 -13 / -19 18 650 / 780 -13 / -19 19 780 / 1040 -13 / -19 20 1040 -13 21 450 -13 22 950 -13 23 1800 -13 24 400 / 450 -13/-13 25 -- reserve -- - 26 -- reserve -- - 27 -- reserve -- - 28 -- reserve -- -...

  • Page 470

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 13 external hold tone 0 0 0 0 32 (0 db) 14 internal ring-back tone (internal audible ring) (ring back tone) 0 2 10 0 10 30 20 (- 6 db) 20 (- 6 db) 15 override tone 1 1 12 5 32 (0 db) 16 lock-out tone...

  • Page 471

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 30 doorphone call tone 1 2 0 6 1 1 32 (0 db) 32 (0 db) 31 paging tone 2 2 0 6 1 1 32 (0 db) 32 (0 db) 32 splash tone 1 1 2 0 6 1 1 32 (0 db) 32 (0 db) 33 splash tone 2 2 2 0 6 1 1 32 (0 db) 32 (0 db)...

  • Page 472

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 57 headset ear piece ringing tone 0 5 0 2 0 2 0 2 1 1 1 20 32 (0 db) 32 (0 db) 32 (0 db) 32 (0 db) 32 (0 db) 58 opening chime tone 1 8 2 2 14 14 15 15 16 16 2 2 2 2 2 2 6 4 32 (0 db) 26 (- 3 db) 32 (...

  • Page 473: 80-02 : Dtmf Tone Setup

    Program 80 : basic hardware setup for system 80-02 : dtmf tone setup level: mf description use program 80-02 : dtmf tone setup to define the duration (on time) and pause (off time) for dtmf dialing. This option affects all trunk line calls system wide. Make separate entries for duration and pause. I...

  • Page 474

    Program 80 : basic hardware setup for system 80-03 : dtmf tone receiver setup level: mf description use program 80-03 : dtmf tone receiver setup to define the various levels and timers for the dtmf tone receiver. Dtmf tone receiver type : • 1 = dtmf receiver for extension • 2 = dtmf receiver for tru...

  • Page 475

    Item no. Item input data description default 04 max. Detect level 0 ~ 15 dtmf tone 0 = 0 dbm (0) to - 15 dbm (15) dtmf tone 1 = - 5 dbm (0) to - 20 dbm (15) dtmf tone 2 = - 10 dbm (0) to - 25 dbm (15) dtmf tone 3 = - 15 dbm (0) to - 30 dbm (15) dtmf tone 4 = - 20 dbm (0) to - 35 dbm (15) dtmf tone 5...

  • Page 476

    Program 80 : basic hardware setup for system 80-04 : call progress tone detector setup level: mf description use program 80-04 : call progress tone detector setup to define the various levels and timers for the call progress tone detector. Tone detector type : • 1 = dial tone for trunk • 2 = busy to...

  • Page 477

    Item no. Item input data default 08 off minimum time 1 ~ 255 (30 + 30 ~ 7680 ms) refer below 09 off maximum time 0 ~ 255 (30 + 30 ~ 7680 ms) refer below 12 frequency no. 1 1 ~ 8 (frequency table no. Set by 80-07) refer below 13 frequency no. 2 0 ~ 8 (0 = not used) (frequency table no. Set by 80-07) ...

  • Page 478

    Program 80 : basic hardware setup for system 80-05 : date format for smdr and system level: mf description use program 80-05 : date format for smdr and system to define the date format when printing out the smdr, alarm report, and system information report. Input data item no. Item input data defaul...

  • Page 479

    Program 80 : basic hardware setup for system 80-07 : call progress tone detector frequency setup level: mf description use program 80-07 : call progress tone detector frequency setup to set the frequency of the detection tone set with program 80-04-12 and program 80-04-13. Input data frequency table...

  • Page 480: 80-08 : Mfc Tone Setup

    Program 80 : basic hardware setup for system 80-08 : mfc tone setup level: in description use program 80-08 : mfc tone setup to define the duration (on time) and pause (off time) for mfc dialing. This option affects all trunk line calls system wide. And also it is possible to adjust the level of ton...

  • Page 481: 80-09 : Short Ring Setup

    Program 80 : basic hardware setup for system 80-09 : short ring setup level: in description use program 80-09 : short ring setup to define the short ring tone for sl1100 multiline terminals. Input data short ring number 01 ~ 32 item no. Item input data description default 01 frequency 1 00 = no sett...

  • Page 482

    Table 2-15 ring cycle table data ring cycle (ms) 01 125 (on) / off 02 125 (on) / 125 (off) / 125 (on) / off 03 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 04 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 05 250 (on) / off 06 250 (on) / 250 (off)...

  • Page 483

    Program 80 : basic hardware setup for system 80-10 : mf tone receiver setup level: mf description use program 80-10 : mf tone receiver setup to define the various level and time for mf tone receiver. Input data mf tone receiver type number 1 = mf receiver for extension 2 = mf receiver for trunk 3 = ...

  • Page 484

    Default item no. Item name type 1 type 2 type 3 type 4 type 5 01 detect level 0 0 0 0 0 02 start delay time 0 0 0 0 0 03 min. Detect level 10 (- 20 dbm) 10 (- 20 dbm) 10 (- 20 dbm) 10 (- 20 dbm) 10 (- 20 dbm) 04 max. Detect level 2 (- 2 dbm) 2 (- 2 dbm) 2 (- 2 dbm) 2 (- 2 dbm) 2 (- 2 dbm) 05 twist l...

  • Page 485

    Program 80 : basic hardware setup for system 80-12 : caller id receiver setup level: in description use program 80-12 : caller id receiver setup defines the type and level for caller id detection of dsp. Input data item no. Item input data default 01 type 0 = ntt 1 = other 2 = korea 1 02 level (mark...

  • Page 486

    Program 81 : basic hardware setup for trunk 81-01 : co initial data setup level: in description use program 81-01 : co initial data setup to define the various basic data parameters for the coiu. Input data item no. Item input data default 01 pcm encoding method specifica- tion 0 = μ-law 1 = a-law 0...

  • Page 487

    Item no. Item input data default 23 loop disconnect detect maximum time 1 ~ 255 (10 ~ 2550 ms) 64 (640 ms) 27 dial pulse break time (10pps) 1 ~ 255 (5 ~ 1275 ms) 12 (60 ms) 28 dial pulse make time (10pps) 1 ~ 255 (5 ~ 1275 ms) 8 (40 ms) 29 dp inter-digit time (10pps) 1 ~ 255 (10 ~ 2550 ms) 80 (800 m...

  • Page 488

    Program 81 : basic hardware setup for trunk 81-05 : isdn pri layer 2 (t-point) initial data setup level: mf description use program 81-05 : isdn pri layer 2 (t-point) initial data setup to define the various basic data for layer 2 of isdn pri. Input data item no. Item input data description default ...

  • Page 489

    Program 81 : basic hardware setup for trunk 81-06 : isdn pri layer 3 (t-point) timer setup level: in description use program 81-06 : isdn pri layer 3 (t-point) timer setup to define the various basic timers for layer 3 of isdn pri (defined in program 10-03-04). Input data layer 3 timer type number 1...

  • Page 490

    Item no. Item input data description default 11 t312 1 ~ 254 seconds specifies the timer value in 1/100ths of a second of the timer to be started when setup is sent or re-sent on broadcast da- ta link. This timer is only valid for network side use only. 6 12 t313 1 ~ 254 seconds specifies the timer ...

  • Page 491

    Program 81 : basic hardware setup for trunk 81-07 : codec filter setup for analog trunk port level: in description use program 81-07 : codec filter setup for analog trunk port to define the codec (qslac) filter for each analog trunk port. Input data trunk port number 001 ~ 084 item no. Item input da...

  • Page 492: 81-08 : T1 Trunk Timer Setup

    Program 81 : basic hardware setup for trunk 81-08 : t1 trunk timer setup level: in description use program 81-08 : t1 trunk timer setup to define the basic timer setting of each t1 trunk type. Input data item no. Item input data default 01 answer signal detection time (loop) 1 ~ 250 (4 ms ~ 1000 ms)...

  • Page 493

    Item no. Item input data default 20 ringing signal stop detection time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 50 (5000 ms) 21 loop current detection time (loop) 1 ~ 250 (4 ms ~ 1000 ms) 40 (160 ms) 22 loop current detection time (ground) 1 ~ 250 (4 ms ~ 1000 ms) 40 (160 ms) 23 loop current detection time...

  • Page 494

    Item no. Item input data default 54 receive hookflash duration min. Time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 3 (300 ms) 55 receive hookflash duration max. Time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 6 (600 ms) 56 loop off guard time (loop) 1 ~ 255 (100 ms ~ 25500 ms) 20 (2000 ms) 57 loop off guard time (gr...

  • Page 495

    Program 81 : basic hardware setup for trunk 81-09 : cot codec (qslac) filter setting level: in description use program 81-09 : cot codec (qslac) filter setting to define the filter setting data (when program 81-07 is set to 4). Input data item no. Item input data default 01 b1 filter setup (1) 0 ~ 2...

  • Page 496

    Item no. Item input data default 30 z filter coefficients (13) 0 ~ 255 84 31 z filter coefficients (14) 0 ~ 255 31 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 170 34 r filter coefficients (2) 0 ~ 255 192 35 r filter coefficients (3) 0 ~ 255 187 36 r filter coefficien...

  • Page 497: Extension

    Program 82 : basic hardware setup for extension 82-01 : incoming ring tone level: mf description use program 82-01 : incoming ring tone to set the incoming ring tones, which are the tones a user hears when a call rings an extension. These tones are grouped into four ring tone ranges (1 ~ 4), also ca...

  • Page 498

    Item no. Item input data default 03 modulation 0 = no modulation 1 = 8 hz modulation 2 = 16 hz modulation 3 = envelope refer below default table 2-17 82-01 default table incoming ringing tone number tone type frequency 1 (hz) frequency 2 (hz) modulation pattern 1 (trunk incoming) high mid low 1100 h...

  • Page 499: Extension

    Program 82 : basic hardware setup for extension 82-04 : astu initial data setup level: mf description use program 82-04 : astu initial data setup to set the basic data of the slt. Input data item no. Item input data default 01 companding method type 0 = μ-law 1 = a-law 0 02 ringing frequency 0 = 25 ...

  • Page 500: Extension

    Program 82 : basic hardware setup for extension 82-05 : isdn pri layer2 (s-point) initial data setup level: mf description use program 82-05 : isdn pri layer2 (s-point) initial data setup to set the basic data for the layer 2 of isdn pri s-point. Input data item no. Item input data default 01 timer ...

  • Page 501: Extension

    Program 82 : basic hardware setup for extension 82-06 : isdn pri layer3 (s-point) timer setup level: in description use program 82-06 : isdn pri layer3 (s-point) timer setup to set the basic timer for the layer 3 of isdn pri s-point. Input data layer3 timer type no. 1 ~ 5 item no. Item input data de...

  • Page 502

    Feature cross reference none sl1100 issue 4.0 2-482 program 82 : basic hardware setup for extension program 82.

  • Page 503: Extension

    Program 82 : basic hardware setup for extension 82-07 : codec filter setup for analog station port level: in description use program 82-07 : codec filter setup for analog station port to set the filter value of the codec (qslac) filter of each analog port. Input data station port number 001 ~ 128 (v...

  • Page 504: Extension

    Program 82 : basic hardware setup for extension 82-08 : sidetone volume setup level: mf description use program 82-08 : sidetone volume setup for adjusting the telephone sidetone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Input data item no...

  • Page 505: Extension

    Program 82 : basic hardware setup for extension 82-09 : sliu codec filter data setup level: in description use program 82-09 : sliu codec filter data setup to define the filter setting data (when program 82-07 is set to 4). Input data item no. Item input data default 01 b1 filter setup (1) 0 ~ 255 1...

  • Page 506

    Item no. Item input data default 28 z filter coefficients (11) 0 ~ 255 43 29 z filter coefficients (12) 0 ~ 255 169 30 z filter coefficients (13) 0 ~ 255 166 31 z filter coefficients (14) 0 ~ 255 159 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 220 34 r filter coeffic...

  • Page 507

    Feature cross reference none issue 4.0 sl1100 programming manual 2-487 program 82.

  • Page 508: Extension

    Program 82 : basic hardware setup for extension 82-11 : sliu initial data setup level: in description use program 82-11 : sliu initial data setup to define the various timers for sliu. Input data item no. Item input data description default 01 bounce protect time 0 = no setting 1 ~ 15 = 100 ms ~ 1.5...

  • Page 509: Extension

    Program 82 : basic hardware setup for extension 82-12 : opx initial data setup level: in description use program 82-12 : opx initial data setup to define the various initial data for opx packages. Input data item no. Item input data description default 01 bounce protect time 0 = no setting 1 ~ 15 = ...

  • Page 510: Extension

    Program 82 : basic hardware setup for extension 82-14 : handset/headset gain setup for multi line telephone level: in description use program 82-14: handset/headset gain setup for multi line telephone to define the handset/ headset gain level for multi line telephone. Input data extension number up ...

  • Page 511: Extension

    Program 82 : basic hardware setup for extension 82-21 : sensor setup level: in description use program 82-21 : sensor setup to setup the sensor for sl1100. Input data sensor number 1 ~ 6 item no. Item input data description default 01 sensor type 0 = close detect 1 = open detect set sensor type. 0 0...

  • Page 512

    Program 84 : hardware setup for voipdb 84-02 : h.225 and h.245 information basic setup level: in description use program 84-02 : h.225 and h.245 information basic setup to define the basic setup information of h.225 and h.245. Input data item no. Item input data default 01 h.225 alerting time 0 ~ 25...

  • Page 513

    Item no. Item input data default 29 ras lrq timer 0 ~ 255 seconds 5 30 lrq retry count 0 ~ 255 2 31 ras rai timer 0 ~ 255 seconds 3 32 rai retry count 0 ~ 255 2 33 call signaling port number 0 ~ 65535 : 0 ~ 1719, 1721 ~ 65535 1730 35 fast start mode 0 = disable 1 = enable 1 36 ras unicast port numbe...

  • Page 514

    Program 84 : hardware setup for voipdb 84-07 : firmware download setup level: in description use program 84-07 : firmware download setup to configure the settings related to central firmware download for ip phones. Input data item no. Item input data description default 01 server mode 0 = tftp 1 = f...

  • Page 515: 84-09 : Vlan Setup

    Program 84 : hardware setup for voipdb 84-09 : vlan setup level: in description use program 84-09 : vlan setup to set up the vlan data. I/f no.2 the packets send from lan i/f on voipdb is set the vlan tag. Input data interface number 1 ~ 2 item no. Item input data default 01 vlan 0 = disable (off) 1...

  • Page 516: 84-10 : Tos Setup

    Program 84 : hardware setup for voipdb 84-10 : tos setup level: in description use program 84-10 : tos setup to set up the type of service data. Input data protocol type 1 ~ 3 = not used 4 = networking (v1.5 changed) 5 = rtp/rtcp 6 = sip 7 = not used 8 = sip-mlt 9 = sip trunk 10 = not used item no. ...

  • Page 517

    Program 84 : hardware setup for voipdb 84-12 : networking codec information basic setup level: in (this program is available for v1.5 or higher) description use program 84-12 : networking codec information basic setup to set voice (rtp packet) encoding parameters. Input data item no. Item input data...

  • Page 518

    Item no. Item input data description default 17 jitter buffer mode 1 = static 3 = adaptive immediate- ly 3 18 vad threshold 01 ~ 30 (19 db ~ +10 db) 1 = -19 db (-49 dbm) : 20 = 0 db (-30 dbm) : 29 = 9 dbm(-21 dbm) 30 = 10 dbm(-20 dbm) 20 28 audio capability pri- ority 0 = g.711_pt 1 = g.723_pt 2 = g...

  • Page 519

    Program 84 : hardware setup for voipdb 84-13 : sip trunk codec information basic setup level: in description use program 84-13 : sip trunk codec information basic setup to set up the basic codec options for sip trunks. Input data item no. Item input data description default related program 01 number...

  • Page 520

    Item no. Item input data description default related program 15 g.723 jitter buf- fer - standard 0 ~ 300 ms set the average value of the g.723 jitter buffer. 60 16 g.723 jitter buf- fer - maximum 0 ~ 300 ms set the maximum value of the g. 723 jitter buffer. 120 17 jitter buffer mode 1 = static 3 = a...

  • Page 521

    Item no. Item input data description default related program 40 g.726 jitter buf- fer - minimum 0 ~ 255 ms set the minimum value of the jitter buffer of g.726 is set. Jitter is the variation in the time between pack- ets arriving and the buffer allows this variation to be absorbed. 30 41 g.726 jitte...

  • Page 522

    Item no. Item input data description default related program 65 vad negotiation on sdp (future) (v2.0 added) 0 = disable 1 = enable this prg is used to determine the vad determination method setting vad information on sdp. This prg is effective when vad is enabled on each codec. G.711 and g.729 are ...

  • Page 523

    Program 84 : hardware setup for voipdb 84-14 : sip trunk basic information setup level: in description use program 84-14 : sip trunk basic information setup to define the basic setup for sip trunks. Input data item no. Item input data description default 01 invite retx count specifies the number of ...

  • Page 524

    Item no. Item input data description default 16 sip trunk sip-uri e. 164 incoming mode (v2.0 added) 0 = off 1 = mode 1 2 = mode 2 0 17 call forward moved temporarily support (v3.0 added) 0 = disabled 1 = 302 return when enabled a 302 moved temporarily response is sent for external call forward desti...

  • Page 525

    Program 84 : hardware setup for voipdb 84-15 : sip phone keep alive setup level: in description use program 84-15 : sip phone keep alive setup to set the keep alive configuration of the sip phone. Input data item no. Item input data description default 01 registration informa- tion automatic dele- t...

  • Page 526

    Program 84 : hardware setup for voipdb 84-16 : voipdb limiter control gain setup level: in description use program 84-16 : voipdb limiter control gain setup to set the limiter control gain configuration of voipdb. Input data item no. Item input data description default 01 rx limiter control gain 0 ~...

  • Page 527

    Feature cross reference none issue 4.0 sl1100 programming manual 2-507 program 84.

  • Page 528

    Program 84 : hardware setup for voipdb 84-19 : sip extension codec information basic setup level: in description use program 84-19 : sip extension codec information basic setup to define the codec information for the sip extensions. Input data item no. Item input data description default 01 number o...

  • Page 529

    Item no. Item input data description default 16 g.723 jitter buffer - maximum 0 ~ 300 ms set the maximum value of the g.723 jitter buffer. 120 17 jitter buffer mode 1 = static 3 = adaptive immediately set the mode of the jitter buffer. 1 = size set to the fixed amount for the co- dec. 2 = the minimu...

  • Page 530

    Item no. Item input data description default 42 g.726 jitter buffer - maximum 0 ~ 255 ms set the maximum g.726 jitter buffer. 120 43 ilbc audio frame 2 = 20 ms 3 = 30 ms 4 = 40 ms maximum number of ilbc audio frames. Ilbc assumes the frame of 10ms is a unit. 3 45 ilbc jitter buffer - minimum 0 ~ 255...

  • Page 531

    Program 84 : hardware setup for voipdb 84-20 : sip extension basic information setup level: in description use program 84-20 : sip extension basic information setup to set up proxy information, session timers, called party information and expire value of invite. Input data item no. Item input data d...

  • Page 532

    Program 84 : hardware setup for voipdb 84-22 : dr700 multiline logon information setup level: sa description use program 84-22 : dr700 multiline logon information setup to set the dr700 multiline logon information. Input data personal id index 001 ~ 128 (v3.5 changed) item no. Item input data descri...

  • Page 533

    Program 84 : hardware setup for voipdb 84-23 : dr700 multiline basic information setup level: in description use program 84-23 : dr700 multiline basic information setup to set the basic information for the dr700 multiline terminal. Input data item no. Item input data description default 01 registrat...

  • Page 534

    Item no. Item input data description default 14 refer expire timer 0 ~ 65535 seconds 60 seconds conditions none feature cross reference none sl1100 issue 4.0 2-514 program 84 : hardware setup for voipdb program 84.

  • Page 535

    Program 84 : hardware setup for voipdb 84-24 : dr700 multiline codec basic information setup level: in description use program 84-24 : dr700 multiline codec basic information setup to set the codec of each type of dr700 multiline telephone. Input data type 1 = type 1 2 = type 2 3 = type 3 4 = type 4...

  • Page 536

    Item no. Item input data description default 08 g.729 silence com- pression (vad) mode 0 = disable 1 = enable select whether to compress silence with g.729. When there is silence, the rtp packet is not sent. When vad is enabled the cpu will stop sending silence packets but the ip phone will continue...

  • Page 537

    Item no. Item input data description default 38 dtmf level mode 0 = use the default of voipdb unit 1 = use the main sys- tem 0 39 dtmf level high 1 = - 33 dbm : 28 = - 6 dbm 28 40 dtmf level low 1 = - 33 dbm : 28 = - 6 dbm 28 conditions none feature cross reference none issue 4.0 sl1100 programming ...

  • Page 538

    Program 84 : hardware setup for voipdb 84-26 : voip basic setup (dsp) level: in description use program 84-26 : voip basic setup to set the ip address and the port of voip. Input data slot number 0 voipdb gw number gw number will not be shown in telephone programming mode. 1 item no. Item input data...

  • Page 539: 84-27 : Voip Basic Setup

    Program 84 : hardware setup for voipdb 84-27 : voip basic setup level: in description use program 84-27 : voip basic setup to set the dtmf relay and the srtp mode of the voipdb. Input data slot number 0 item no. Item input data description default 01 dtmf relay setup 0 = dtmf relay disa- bled 1 = in...

  • Page 540

    Item no. Item input data description default 14 icmp redirect 0 = enabled, voice packets will follow icmp redirect messages. 1 = disabled, voice packets will not follow the icmp redirect mes- sage. 1 15 dtmf detect mini- mum duration 23 ~ 2000 ms this setting is the minimal time setting to distingui...

  • Page 541

    Program 84 : hardware setup for voipdb 84-28 : dr700 multiline firmware name setup level: in description use program 84-28 : dr700 multiline firmware name setup to set the firmware name to download for the ip phone. Input data terminal type 1 ~ 3 = not used 4 = ip4ww-24tixh item no. Item input data ...

  • Page 542

    Program 84 : hardware setup for voipdb 84-29 : sip-mlt codec information fixed mode setup level: in description use program 84-29 : sip-mlt codec information fixed mode setup to set the codec data of the sip-mlt when it uses multicast. Input data type 1 = type 1 (multicast) 2 = type 2 (reserved) 3 =...

  • Page 543

    Program 84 : hardware setup for voipdb 84-31 : voipdb echo canceller setup level: in description use program 84-31 : voipdb echo canceller setup to sets voipdb echo canceller value. Input data type 1 = h.323 trunk 2 ~ 6 = not used (v1.5 changed) 7 = networking (v1.5 changed) 8 = sip trunk 9 = sip ex...

  • Page 544

    Item no. Item input data description default related program 07 tdm echo can- celler default erl level (v2.0 added) 0 ~ 6 (- 9 db ~ 9 db) 0 = - 9 db 1 = - 6 db 2 = - 3 db : 5 = 6 db 6 = 9 db do not change the setting unless asked to change by engineer. Select length of echo. Effective when prg 84-31...

  • Page 545

    Item no. Item input data description default related program 29 rtp tx level control level 0 ~ 16 (- 24 ~ 24 db) 0 = - 24 db 1 = - 21 db 2 = - 18 db : 8 = 0 db : 14 = 18 db 15 = 21 db 16 = 24 db 8 30 rtp tx automa- ticlevelcontrol level (v2.0 add- ed) 0 ~ 12 (- 42 dbm~ - 6 dbm) 0 = - 42 dbm 1 = - 39...

  • Page 546

    Item no. Item input data description default related program 37 tdm echo can- celler nlp mode (4w) 0 = disable 1 = enable 2 = echo path mode 3 = echo path auto de- tect mode 1 conditions none feature cross reference none sl1100 issue 4.0 2-526 program 84 : hardware setup for voipdb program 84.

  • Page 547

    Program 84 : hardware setup for voipdb 84-32 : fax over ip codec setup level: in (this program is available for v4.0 or higher) description use program 84-32 : fax over ip codec setup to program the codecs used when faxing across sip trunk. Note these settings must match in both systems for faxing a...

  • Page 548

    Program 84 : hardware setup for voipdb 84-39 : sip trunk message customize level: in (this program is available for v4.0 or higher) description this program is not available for web programming or telephone programming. You can only change setting using script function of pc programming. Use program...

  • Page 549: 90-01 : Installation Date

    Program 90 : maintenance program 90-01 : installation date level: in description use program 90-01 : installation date to define the installation date of the system. Input data item no. Item input data default 01 year 00 ~ 99 00 (no setting) 02 month 01 ~ 12 00 (no setting) 03 day 01 ~ 31 00 (no set...

  • Page 550

    Program 90 : maintenance program 90-02 : programming password setup level: in description use program 90-02 : programming password setup to set the system passwords. For password entry, the system allows eight users to be defined. Each user can have a: • unique alphanumeric name (up to 10 alphanumer...

  • Page 551

    User no. User name password level level description 5 user1 1111 5 (ua) user programming administer mode lev- el 1 conditions • more than one extension can be in the programming mode. Feature cross reference none issue 4.0 sl1100 programming manual 2-531 program 90

  • Page 552: 90-03 : Save Data

    Program 90 : maintenance program 90-03 : save data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-03 : save data to save the programmed data on the cf card. This program should be used after changing the programmed ...

  • Page 553: 90-04 : Load Data

    Program 90 : maintenance program 90-04 : load data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-04 : load data to load the system data from the inserted cf card into the pz-vm21 daughter board installed to the sys...

  • Page 554: 90-05 : Slot Control

    Program 90 : maintenance program 90-05 : slot control level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-05 : slot control to reset or delete (uninstall) units (slots 0 ~ 15 (v3.5 or higher)). Delete allows you to com...

  • Page 555: 90-06 : Trunk Control

    Program 90 : maintenance program 90-06 : trunk control level: sa description use program 90-06 : trunk control for trunk maintenance. Busy out lets you block a unit from placing outgoing calls (just like placing the unit switch down). Once busied out, none of the ports on the unit can be used for ne...

  • Page 556: 90-07 : Station Control

    Program 90 : maintenance program 90-07 : station control level: sa description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-07 : station control for extension maintenance. Input data menu number 1 = hardware reset 2 = software reset ...

  • Page 557: 90-08 : System Reset

    Program 90 : maintenance program 90-08 : system reset level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-08 : system reset to perform a system reset. Input data item no. Item input data default 01 system reset dial 1 + ...

  • Page 558

    Program 90 : maintenance program 90-09 : automatic system reset time setup level: in description use program 90-09 : automatic system reset time setup to define the time for the system to automatically reset. Input data item no. Item input data default 01 month 00 ~ 12 if the month is set to 00 and ...

  • Page 559: 90-10 : System Alarm Setup

    Program 90 : maintenance program 90-10 : system alarm setup level: in description use program 90-10 : system alarm setup to assign a status to system alarms. You can designate an alarm as major or minor. This program also assigns whether or not the alarm information is reported to the pre-defined de...

  • Page 560

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 3 2 0 connec- tion fault between cpu and other pkgs. The error occur- red when com- municating with the package. When the pack- age is broken, it recognizes it as a communica- tion fault. 1. The unit is not completely i...

  • Page 561

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 6 0 0 blocking the link of ter- minals connec- ted with the esi package came off. 1. Terminal breakdown. 2. Faulty wiring and wiring ter- mination. 3. External noise. 4. Esi package breakdown. Confirm the termi- nal con...

  • Page 562

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 17 1 0 denial of service the system re- ceived illegal packet. Service outage (dos attack) confirm whether to find abnormality on the net side. War 18 1 0 connec- tion error digital station wiring error the wiring conne...

  • Page 563

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 57 2 0 ip colli- sion error check the ip address colli- sion (cpu, voipdb, pro- gram 84-26-01 gw : 1 ~ 8). Collision ip ad- dress in the net- work. Check the ip ad- dress in the net- work. Recover the ip address collisi...

  • Page 564

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 63 0 0 sip-mlt trouble in- formation. 1. The trouble occurred by the sip- mlt rela- tion. 2. The dsp resource could not be acquired at incom- ing/outgo- ing. 3. The nego- tiation with voipdb failed. 1. The packet loss o...

  • Page 565

    • system alarm type is shown despite the setting done at 90-10-01. If multiple alarm display setting is set, only one highest priority alarm will be shown on a lcd display. • the priority level (highest -> lowest) : alarm 55 > alarm 7 > alarm 5 > alarm 30 > alarm 8 > alarm 52> alarm 29 > free demo l...

  • Page 566

    Program 90 : maintenance program 90-11 : alarm report smtp setting level: in description use program 90-11 : alarm report smtp setting to define the details of the system alarm report. Input data item no. Item input data description default related program 02 report method 0 = no report 1 = e-mail a...

  • Page 567

    Item no. Item input data description default related program 15 dimlog notifica- tion (v2.0 added) 0 = no 1 = yes prg 90-11-14=yes (prg 47-18 smtp client uses) and cf mount are necessary. In the case of system fault, dim- last.Gz and dimdump.Gz are noti- fied. 0 90-11-14 conditions none feature cros...

  • Page 568: 90-12 : System Alarm Output

    Program 90 : maintenance program 90-12 : system alarm output level: in description use program 90-12 : system alarm output to set the options for the alarm report. This program has six separate menu options. Define the output port to be used as the output for system alarm report and set the system a...

  • Page 569

    Program 90 : maintenance program 90-13 : system information output level: in description use program 90-13 : system information output to define the output port to be used as the system information output. Input data item no. Item input data description default 01 output port type 0 = no setting 5 =...

  • Page 570

    Program 90 : maintenance program 90-16 : main software information level: in description use program 90-16 : main software information to display the main software information on the cpu. Input data item no. Item input data default 01 version number read only: 01.00 ~ 99.99 ascii code (5 bytes) 02 s...

  • Page 571: 90-17 : Firmware Information

    Program 90 : maintenance program 90-17 : firmware information level: in description use program 90-17 : firmware information to display the firmware versions of the various system units. Input data item no. Item input data default 01 dsp firmware version no. Read only: 00.00.00.00 ~ 15.15.15.15 bcd ...

  • Page 572: 90-19 : Dial Block Release

    Program 90 : maintenance program 90-19 : dial block release level: sa description note: this program is available via telephone programming and webpro not through pc programming. When the extension number is entered in program 90-19 : dial block release, the extension is released from the dial block...

  • Page 573

    Program 90 : maintenance program 90-20 : traffic report data setup level: in description use program 90-20 : traffic report data setup to define the details of the traffic report. Input data item no. Item input data description default 01 call traffic output 0 = not measured 1 = measure 0 03 all lin...

  • Page 574

    Feature cross reference • traffic reports sl1100 issue 4.0 2-554 program 90 : maintenance program program 90

  • Page 575

    Program 90 : maintenance program 90-21 : traffic report output level: in description use program 90-21 : traffic report output to define the output port to be used as the traffic report output. Input data item no. Item input data default 01 output port type 0 = no setting 3 = lan 0 conditions none f...

  • Page 576

    Program 90 : maintenance program 90-23 : deleting registration of ip telephones level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-23 : deleting registration of ip telephones to delete the registered ip telephone from...

  • Page 577

    Program 90 : maintenance program 90-24 : system alarm report notification time setup level: in description use program 90-24 : system alarm report notification time setup to set the date and time for the alarm report to print. Input data notification number 1 ~ 12 item no. Item input data default 01...

  • Page 578

    Program 90 : maintenance program 90-25 : system alarm report cc mail setup level: in description use program 90-25 : system alarm report cc mail setup to define the mail address to receive the system alarm report cc mail setup. Input data cc number 1 ~ 5 item no. Item input data default 01 cc mail a...

  • Page 579

    Program 90 : maintenance program 90-26 : program access level setup level: in description use program 90-26 : program access level setup to define the password access level required to change a system program. Input data program numbers 1001 ~ 9903 item no. Item input data default 01 maintenance lev...

  • Page 580

    Program 90 : maintenance program 90-28 : user programming password setup level: in description use program 90-28 : user programming password setup to set the password used to enter the user programming mode. Input data extension numbers maximum eight digits item no. Item input data default 01 passwo...

  • Page 581

    Program 90 : maintenance program 90-31 : dim access over ethernet level: in description use program 90-31 : dim access over ethernet to enable dim (diagnostic information maintenance) access over the lan, and to define the user name and password. Dim is a maintenance tool used by engineering to extr...

  • Page 582

    Program 90 : maintenance program 90-33 : preselected data setup level: in description note: this program is available only via telephone programming and not through pc programming. Use 90-33 : preselected data setup to setup the system to preselected setting. Input data item no. Item input data defa...

  • Page 583

    Program no. Name default 21-03-01 trunk group routing for trunks 1 (all trunks : all modes : group1) 22-01-03 incoming ring no answer alarm start timer 30 22-01-04 normal dil incoming no answer timer 30 22-01-08 did (ddi) pilot call no answer timer 30 22-08-01 second irg setup for unanswered 1 (all ...

  • Page 584

    Program no. Name default 80-01-02 basic tone no 1 (svc tone 2 unit 1) 12-01-02 automatic night mode switch 0 20-02-07 display mode of date and time 8 20-02-09 disconnect supervision 1 20-02-12 mode setting for incoming call from extension 1 20-07-11 force trunk disconnection (analog trunk only) 1 (c...

  • Page 585

    Program no. Name default 40-07-01 voice prompt language assignment for system based 7 47-02-16 voice prompt language 7 47-06-14 voice prompt language 7 47-07-03 prompt language 7 47-10-03 voice prompt language 7 taiwan program no. Name default 15-01-01 extension name - (delete all station name) 20-0...

  • Page 586

    Program no. Name default 20-13-01 long conversation alarm 0 (class 1 only) 20-13-22 called party status 1 (class 1 only) 20-09-04 notification for incoming call list existence 0 (class 1 only) 14-02-18 busy tone detection on talking 1 (trunks 1 ~ 27) 14-02-19 busy tone detection frequency 3 (trunks ...

  • Page 587

    Program no. Name default 25-05-01 vrs/disa error message assignment 4 (trunks 1 ~ 27 mode 1, 2) 40-10-08 call attendant message - when busy 8 40-10-09 call attendant message - when no answer 9 25-06-02 did/disa one-digit code attendant setup msg (1, 2, 4, 8, 9) recv. 9 data=101 14-01-13 loop disconn...

  • Page 588

    Program no. Name default 14-02-18 busy tone detection talking 1 15-01-01 extension name - 15-03-09 extension display 1 15-03-15 hook disconnect mode 1 16-01-03 auto step call 1 16-01-04 hunting mode 1 16-01-08 max queue no 32 20-02-04 transfer retrieve 1 20-02-11 microphone of key telephone 0 20-02-...

  • Page 589

    Program no. Name default 25-07-01 vrs dial time 5 25-07-02 disa no answer time 60 25-07-03 disa disconnect retransfer to irg 30 31-02-01 internal paging group 1 31-02-02 internal all paging group 1 32-01-02 door box lock cancel 1 35-01-04 smdr-omit digits 0 35-02-09 smdr-extension number or name 1 3...

  • Page 590

    Program no. Name default 20-13-01 long conversation alarm 0 (class 1 only) 20-13-22 called party status 1 (class 1 only) 20-17-01 operator extension number 101 20-19-02 caller id wait timer 0 21-01-06 dial pause at first digit of dialing 1 22-01-11 vrs waiting message interval time 10 24-02-03 delay...

  • Page 591

    Program no. Name default 12-02-01 automatic night service pattern (time pattern 2) set time 01 = s 0000, e 0800, m2 modegrp 1 12-02-01 automatic night service pattern (time pattern 2) set time 02 = s 0800, e 1200, m1 modegrp 1 12-02-01 automatic night service pattern (time pattern 2) set time 03 = s...

  • Page 592

    Program no. Name default 15-02-34 call register mode 1 (all stations) 15-03-12 fixed cadence 0 (all stations) 15-07-01 programmable function key key 21 : 00 key 22 : 00 (all stations) 20-01-01 operator access mode 1 20-02-07 time and date display mode 5 20-02-09 disconnect supervision 1 20-02-11 def...

  • Page 593

    Program no. Name default dial analysis table number 157 06@@@@@@@@@@ dial analysis table number 158 07@@@@@@@@@@ dial analysis table number 159 080@@@@@@@ dial analysis table number 160 081@@@@@@@@@ dial analysis table number 161 082@@@@@@@@@ dial analysis table number 162 083@@@@@@@@@ dial analysis...

  • Page 594

    Program no. Name default dial analysis table number 153 1 dial analysis table number 154 1 dial analysis table number 155 1 dial analysis table number 156 1 dial analysis table number 157 1 dial analysis table number 158 1 dial analysis table number 159 1 dial analysis table number 160 1 dial analys...

  • Page 595

    Program no. Name default dial analysis table number 196 1 26-02-03 additional data dial analysis table number 151 10 dial analysis table number 152 10 dial analysis table number 153 10 dial analysis table number 154 10 dial analysis table number 155 10 dial analysis table number 156 10 dial analysis...

  • Page 596

    Program no. Name default dial analysis table number 192 10 dial analysis table number 193 10 dial analysis table number 194 10 dial analysis table number 195 10 dial analysis table number 196 10 26-02-06 lcr carrier table dial analysis table number 151 1 dial analysis table number 152 2 dial analysi...

  • Page 597

    Program no. Name default 35-02-16 trunk name or received dialed number 2 (port 1 only) 40-07-01 voice prompt language assignment 9 40-08-01 voice prompt language assignment 9 80-04-04 no tone time type 2 bt 7 80-04-06 on minimum time type 2 bt 6 80-04-07 on maximum time type 2 bt 8 80-04-08 off mini...

  • Page 598

    Thailand program no. Name default 10-02-01 country code 66 india program no. Name default 10-02-01 country code 91 conditions none feature cross reference none sl1100 issue 4.0 2-578 program 90 : maintenance program program 90

  • Page 599: 90-34 : Firmware Information

    Program 90 : maintenance program 90-34 : firmware information level: in description use program 90-34 : firmware information to list the package type and firmware units installed in the system. Input data slot number 00 ~ 15 (v3.5 changed) item no. Item input data default 01 package name read only: ...

  • Page 600

    Program 90 : maintenance program 90-35 : wizard programming level setup level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-35 : wizard programming level setup to set the maintenance level for wizard programming. Input d...

  • Page 601

    Program 90 : maintenance program 90-36 : firmware update time setting level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-36 : firmware update time setting to define the data for the firmware update feature. This data is...

  • Page 602

    Conditions none feature cross reference none sl1100 issue 4.0 2-582 program 90 : maintenance program program 90

  • Page 603

    Program 90 : maintenance program 90-37 : set temporary license level: in (this program is available for v4.0 or higher) description use program 90-37 : set temporary license to set the effective days of the temporary license. Input data item no. Item input data default 01 set number of days for temp...

  • Page 604

    Program 90 : maintenance program 90-38 : user programming data level setup level: in description use program 90-38 : user programming data level setup sets system data to turn on/off each user programming feature. Input data item no. Item input data default related program 01 time setting 0 = turn o...

  • Page 605

    Item no. Item input data default related program 18 call forward-immediate/no answer /both ring 0 = turn off 1 = turn on 1 = turn on 11-11-01 11-11-03 11-11-05 19 call forward-busy 0 = turn off 1 = turn on 1 = turn on 11-11-02 20 trunk incoming ring tone 0 = turn off 1 = turn on 1 = turn on 11-11-20...

  • Page 606

    Program 90 : maintenance program 90-39 : virtual loop back port reset level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-39 : virtual loop back port reset to reset to initial status. Input data item no. Item input data ...

  • Page 607

    Program 90 : maintenance program 90-41 : server setting to update terminal local data level: in description use program 90-41 : server setting to update terminal local data to define the primary dns server address, the secondary dns server address and the data roaming server address. Input data serv...

  • Page 608

    Program 90 : maintenance program 90-42 : dr700 multiline terminal version information level: in description use program 90-42 : dr700 multiline terminal version information to set the hardware version and firmware version of the dr700 mlt terminal. Input data terminal type 1 ~ 3 = not used 4 = ip4ww...

  • Page 609

    Program 90 : maintenance program 90-43 : deleting terminal license of dr700 level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-43 : deleting terminal license of dr700 to delete the terminal license information delivered...

  • Page 610

    Program 90 : maintenance program 90-44 : deleting terminal license of tcp interface level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-44 : deleting terminal license of tcp interface to delete the terminal license infor...

  • Page 611: Telephone

    Program 90 : maintenance program 90-45 : temporary password change for multiline telephone level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-45 : temporary password change for multiline telephone to change the tempor...

  • Page 612

    Program 90 : maintenance program 90-50 : system alarm display setup level: in description use program 90-50 : system alarm display setup to set the system alarm report display. Input data index number 01 ~ 50 item no. Item input data default 01 system alarm display telephone up to eight digits no se...

  • Page 613

    Program 90 : maintenance program 90-51 : alarm setup for maintenance exchange level: in description use program 90-51 : alarm setup for maintenance exchange to set the day for the maintenance exchange of parts that need regular maintenance. Input data index 1 ~ 10 item no. Item input data default 01...

  • Page 614: 90-52 : System Alarm Save

    Program 90 : maintenance program 90-52 : system alarm save level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-52 : system alarm save for the system alarm output operation. Input data item no. Item input data default 01 ...

  • Page 615: 90-53 : System Alarm Clear

    Program 90 : maintenance program 90-53 : system alarm clear level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-53 : system alarm clear to clear the system alarm. Input data item no. Item input data default 01 clear all ...

  • Page 616: 90-54 : Pc/web Programming

    Program 90 : maintenance program 90-54 : pc/web programming level: in description use program 90-54 : pc/web programming sets parameters for pc and web programming. Input data item no. Item input data description default 01 web pro tcp port number 1 ~ 65535 the port number of tcp of the web pro- gra...

  • Page 617: 90-55 : Free License Select

    Program 90 : maintenance program 90-55 : free license select level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-55 : free license select to validate the free license. Input data item no. Item input data default 01 start...

  • Page 618: 90-56 : Ntp Setup

    Program 90 : maintenance program 90-56 : ntp setup level: in description use program 90-56 : ntp setup to set the ntp. Input data item no. Item input data default 01 ntp synchronize 0 = no 1 = yes 0 02 server address ipv4 form : xxx.Xxx.Xxx.Xxx ipv6 form : xxxx.Xxxx.Xxxx.Xxxx.Xxxx no setting conditi...

  • Page 619: 90-57 : Backup Recovery Data

    Program 90 : maintenance program 90-57 : backup recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-57 : backup recovery data to backup the system data in the compact flash memory on the cpu and to make the...

  • Page 620

    Program 90 : maintenance program 90-58 : restore recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-58 : restore recovery data to select the recovery data stored in the compact flash memory of the cpu. Aft...

  • Page 621: 90-59 : Delete Recovery Data

    Program 90 : maintenance program 90-59 : delete recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-59 : delete recovery data to select and delete the recovery data stored in the compact flash memory of the...

  • Page 622

    Program 90 : maintenance program 90-60 : t1/isdn layer status information level: in description use program 90-60 : t1/isdn layer status information to display layer status information for t1 packages. Input data slot no. 00 ~ 15 (v3.5 changed) item no. Item input data default 01 link status read on...

  • Page 623

    Program 90 : maintenance program 90-62 : security id information level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-62 : security id information to view the information for security id. Input data item no. Item input da...

  • Page 624: 90-63 : Dr700 Control

    Program 90 : maintenance program 90-63 : dr700 control level: in description use program 90-63 : dr700 control to adjust settings of the dr700. Input data item no. Item input data default 01 priority timer 0 ~ 255 80 conditions none feature cross reference none sl1100 issue 4.0 2-604 program 90 : ma...

  • Page 625

    Program 90 : maintenance program 90-65 : 1st party cti authentication password setup level: sa description use program 90-65 : 1st party cti authentication password setup to set the authentication password. Input data item no. Item input data description default 01 password up to 16 characters sets ...

  • Page 626

    Program 90 : maintenance program 90-66 : ftp firmware update setup level: in description use program 90-66 : ftp firmware update setup to setup the login info to connect to the ftp server. Input data item no. Item input data description default 01 user name up to 32 characters slsystem 02 password u...

  • Page 627

    Program 90 : maintenance program 90-67 : backup data auto-save interval time set level: in description use program 90-67 : backup data auto-save interval time set to set time interval d-ram data that is saved in f-rom memory. D-ram memory : configuration information such as call transfer and do not ...

  • Page 628: 90-68 : Side Tone Auto Setup

    Program 90 : maintenance program 90-68 : side tone auto setup level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-68 : side tone auto setup to setup the volume level of side tone for each analog trunk port. This program ...

  • Page 629: Program 92 : Copy Program

    Program 92 : copy program 92-01 : copy program level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-01 : copy program to copy the data for one program to another multiline terminal, port, group, or other number. Refer to ...

  • Page 630

    Program no. Program name 22-02 incoming service type setup 22-03 trunk ring tone setup 22-05 irg assignment for normal ring trunk 22-08 second irg setup for unanswered dil / irg 31-05 incoming ring tone audible on external speaker 81–07 codec filter setup for analog trunk port trunk group base progr...

  • Page 631

    Department base program no. Program name 16-01 department (extension) group basic data setup copy all data except group name (item 01). 35-04 smdr port assignment for department group dss console base program no. Program name 30-01 dss console operation mode 30-03 dss key assignment door box base pr...

  • Page 632: Program 92 : Copy Program

    Program 92 : copy program 92-02 : delete all extension numbers level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-02 : delete all extension numbers to delete all extension numbers 11-02>, . However, the extension number...

  • Page 633: Program 92 : Copy Program

    Program 92 : copy program 92-03 : copy program by port number level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-03 : copy program by port number to copy extension and the data of each outside line. Input data program n...

  • Page 634: Program 92 : Copy Program

    Program 92 : copy program 92-04 : extension data swap level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-04 : extension data swap to swap data between two extensions. Input data item no. Item input data 01 1st extension...

  • Page 635

    Program number program name 21-11 hotline assignment 21-13 isdn calling party number setup for extension 21-15 individual trunk group routing for extensions 21-18 ip trunk (h.323) calling party number setup for extension 21-19 ip trunk (sip) calling party number setup for extension 21-20 sip trunk c...

  • Page 636: Program 92 : Copy Program

    Program 92 : copy program 92-05 : extension data swap password level: in description use program 92-05 : extension data swap password to define the 4-digit password for each extension to allow extension data swap. Input data extension number up to eight digits. Item no. Item input data description d...

  • Page 637: Program 92 : Copy Program

    Program 92 : copy program 92-06 : fill command level: in description use program 92-06 : fill command to allocate the data of each extension number of each extension group or each table. Input data program number xx - xx item no. Item input data 01 source number each extension port = 001 ~ 128 (v3.5...

  • Page 638: Program 92 : Copy Program

    Program 92 : copy program 92-07 : delete command level: in description use program 92-07 : delete command to delete the data of each extension number of each extension group or each table. Input data program number xx-xx item no. Item input data 01 destination number (from) each extension port = 001...

  • Page 639

    Program 93 : system information 93-01 : day/night mode information level: sa (this program is available for v3.0 or higher) description use program 93-01 : day/night mode information to display day/night mode for night mode service group. Input data night mode service group no. 1 ~ 4 item no. Item i...

  • Page 640: 93-02 : Trunk Information

    Program 93 : system information 93-02 : trunk information level: sa (this program is available for v3.0 or higher) description use program 93-02 : trunk information to display the setting of each trunk. Input data trunk port number 1 ~ 84 item no. Item input data description default related program ...

  • Page 641

    Program 93 : system information 93-03 : extension information level: sa (this program is available for v3.0 or higher) description use program 93-03 : extension information to display the settings of each extension. Input data extension up to 8 digits item no. Item input data description default rel...

  • Page 642

    Item no. Item input data description default related program 10 alarm clock 1 0 = disable 1 = enable read only: indicates alarm clock 1 setting sta- tus. No setting 11-11-12 11 preset time at alarm 1 time set in alarm clock 1. When prg93-03-11 is "0", 「 00 ： 00 」 is indicated. Read only: indicates t...

  • Page 643: 93-04 : Redial List

    Program 93 : system information 93-04 : redial list level: sa (this program is available for v3.0 or higher) description use program 93-04 : redial list to display the redial list of each extension. Input data extension number up to 8 digits redial last number 10 item no. Item input data description...

  • Page 644

    Program 93 : system information 93-05 : department group information level: sa (this program is available for v3.0 or higher) description use program 93-05 : department group information to display the settings of each department group. Input data department group number 1 ~ 32 item no. Item input d...

  • Page 645

    Memo issue 4.0 sl1100 programming manual 2-625.

  • Page 646

    Programming manual nec corporation issue 4.0